This patch allows passing platform_data to devices attached to AC97 bus
(like touchscreens, battery measurement chips ...).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX9877 needs an address of start register when we write values to
registers through i2c_master_send(), but the code for this was missed in
max9877_write_regs().
If the value of control is 0 in the max9877_set_out_mode(), the value is
not increased to 1, but actually the value to write to the register
should be 1.
And the register bits for out_mode and osc_mode should be cleared before
writing.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Conexant CX20442-11 voice modem codec, suitable
for use by the ASoC board driver for Amstrad E3 (Delta) videophone. Related
sound card driver will follow.
This codec is an optional part of the Conexant SmartV three chip modem design.
As such, documentation for its proprietary digital audio interface is not
available. However, on Amstrad Delta board, thanks to Mark Underwood who
created an initial, omap-alsa based sound driver a few years ago[1], the codec
has been discovered to be accessible not only from the modem side, but also
over the OMAP McBSP based CPU DAI. Thus, the driver can be used by any sound
card that can access the codec DAI directly. The DAI configuration parameters
(sample rate and format, number of channels) has been selected out empirically
for best user experience.
The codec analogue interface consists of two pairs of analogue I/O pins:
speakerphone interface or telephone handset/headset interface. Furthermore, it
seams to provide two operation modes for speakerphone I/O: standard and
advanced, with automatic gain control and echo cancelation. Even if the codec
control interface is unknown and not available, all those interfaces and modes
can be selected over the modem chip using V.253 commands. The driver is able
to issue necessary commands over a suitable hw_write function if provided by a
sound card driver. Otherwise, the codec can be controlled over the modem from
userspace while inactive.
Even if nothig is known about the codec internal power management
capabilities, DAPM widgets has been used to model the codec audio map.
Automatically performed powering up/down of those virtual widgets results in
corresponding V.253 commands being issued.
Some driver features/oddities may be board specific, but I have no way to
verify that with any board other than Amstrad Delta.
[1] http://www.earth.li/pipermail/e3-hacking/2006-April/000481.html
Created and tested against linux-2.6.31-rc3.
Applies and works with linux-omap-2.6 commit
7c5cb7862d32cb344be7831d466535d5255e35ac as well.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
PLL was not being enabled when it was not bypassed. This patch
enables the PLL when it is used. Additionally, it disables the PLL
when it is bypassed.
Without this patch, the audio on TI DM646x EVM and DM355 EVM
does not work properly. The bit clocks and the frame sync signals
from the codec are not correct and hence the playback/record are faster
than usual for most sample rates. The reason for this was that the PLL
was not enabled when it was not bypassed.
Tested on DM6467 EVM, playback tested on DM355 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The callback function to control register was used by whole controls in
MAX9877 driver, but this causes using many if statement for double
register control or invert.
So, the callback function for double register control is separate
differently, and the code for invert is added in the callback function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This corrects a bug with ADC Inversion Switch in wm8974 codec.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reset was failing with the original udelay(50) between the code in
psc_ac97_cold_reset() and the call to psc_ac97_warm_reset(). Through testing
it was found that a delay of 1ms was necessary for the cold_reset code to
consistently complete successfully.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GCC 4.4.0 doesn't appear to be able to spot that we don't apply any FLL
configuration if the output frequency is zero.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Board sdp3430 has hardware support for EXTMUTE using TWL4030 GPIO6
line, controlled by register INTBR_PMBR1. Machine driver takes care
of enabling gpio line through i2c and codec driver manipulates the
line during headset ramp up/down sequence.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
clock name strings are no longer passed on platform_data. Instead,
we rely entirely on struct device and clkdev to find the right clock.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX9877 combines a high-efficiency Class D audio power amplifier
with a stereo Class AB capacitor-less DirectDrive headphone amplifier.
The max9877_add_controls() is called to register the MAX9877 specific
controls on machine specific init() of the machine driver.
The datasheet for the MAX9877 can find at the following url:
http://datasheets.maxim-ic.com/en/ds/MAX9877.pdf
[Slight edit to sort the ALL_CODECS entries -- broonie.]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a macro for double controls with special callback function and
TLV. The SOC_DOUBLE_R_EXT_TLV needs two registers and one shift for
double controls.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a macro for double controls with special callback function and
TLV. The SOC_DOUBLE_EXT_TLV needs one register and two shifts for double
controls.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to the flexibility of the WM9081 FLL this should never happen
in a real system.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to use the best value we picked, not the last value we
looked at.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to manually start playback/capture ourselves as the PCM
driver will handle things for us.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to manually start playback/capture ourselves as the PCM
driver will handle things for us.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without MODULE_LICENCE("GPL"), when built as a module it will fail
to load because it uses other GPL symbols from kernel.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In SOC DAPM layer of SOUND subsystem, when add signal route (in the
function snd_soc_dapm_add_route() ), the original code has wrong logic
when dapm layer check each widget whether an external one.
Signed-off-by: Rongrong Cao <rrcao@ambarella.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Check for rtd->params->drcmr != NULL before accessing it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide an interval after the end of DAPM sequencing so that we
can distinguish between a pop in the final step of the sequence
and a pop generated from some other source outside DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The system clock is currently fixed by the driver and this avoids
the need for us to handle errors with enabling and disabling MCLK
(which was incorrect previously so this fixes bugs in error
handling).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As shipped the board does not have inputs but it is relatively
straightforward to modify the board to hook them up so support
is provided in the driver. When these modifications have not
been made enabling the microphone stage can cause problems.
Add an ifdef to disable this by default. Don't put it into
Kconfig since users will have to get their soldering irons
out to change things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This simplifies the driver by removing the need to manually
configure dividers within the CPU and improve audio performance
by ensuring that the optimal phase relationships between the
clocks in the system are maintained.
Note that currently this means that for playback to work the
Output Mixer HiFi switch must be enabled since otherwise CODEC
will not generate the DAC clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While the hardware is capable of some limited asynmmetric modes the
driver does not currently support those modes so tell applications
that only symmetric rates are available.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8993 is a highly integrated ultra-low power hi-fi CODEC designed
for portable devices such as multimedia phones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the dma link with correct data as soon as
the master channel has copied it. Otherwise, the
1st period will play twice.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Note the slightly tricky cache usage in the volume update function due
to the requirement for a separate write for the VU bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TLV320AIC3x driver is currently the only user of the CODEC hw_read
operation and is jumping through some hoops in order to do so. In order
to support future refactoring to make the hw_read operation more usable
unwrap the usage in this driver to avoid its use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nothing uses it and the existing hw_read operation needs to be
refectored so it's easier to remove it rather than work with it.
Support can be re-added if the code requires volatile registers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A lot of CODECs share the same register data formats and therefore
replicate the code to manage access to and caching of the register
map. In order to reduce code duplication centralised versions of
this code will be introduced with drivers able to configure the use
of the common code by calling the new snd_soc_codec_set_cache_io()
API call during startup.
As an initial user the 7 bit address/9 bit data format used by many
Wolfson devices is supported for write only CODECs and the drivers
with straightforward register cache implementations are converted to
use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
