forked from luck/tmp_suning_uos_patched
eace75cfdc
194 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Srinivas Kandagatla
|
eace75cfdc |
nvmem: Add a simple NVMEM framework for nvmem providers
This patch adds just providers part of the framework just to enable easy review. Up until now, NVMEM drivers like eeprom were stored in drivers/misc, where they all had to duplicate pretty much the same code to register a sysfs file, allow in-kernel users to access the content of the devices they were driving, etc. This was also a problem as far as other in-kernel users were involved, since the solutions used were pretty much different from on driver to another, there was a rather big abstraction leak. This introduction of this framework aims at solving this. It also introduces DT representation for consumer devices to go get the data they require (MAC Addresses, SoC/Revision ID, part numbers, and so on) from the nvmems. Having regmap interface to this framework would give much better abstraction for nvmems on different buses. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> [Maxime Ripard: intial version of eeprom framework] Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Linus Torvalds
|
88793e5c77 |
The libnvdimm sub-system introduces, in addition to the libnvdimm-core,
4 drivers / enabling modules:
NFIT:
Instantiates an "nvdimm bus" with the core and registers memory devices
(NVDIMMs) enumerated by the ACPI 6.0 NFIT (NVDIMM Firmware Interface
table). After registering NVDIMMs the NFIT driver then registers
"region" devices. A libnvdimm-region defines an access mode and the
boundaries of persistent memory media. A region may span multiple
NVDIMMs that are interleaved by the hardware memory controller. In
turn, a libnvdimm-region can be carved into a "namespace" device and
bound to the PMEM or BLK driver which will attach a Linux block device
(disk) interface to the memory.
PMEM:
Initially merged in v4.1 this driver for contiguous spans of persistent
memory address ranges is re-worked to drive PMEM-namespaces emitted by
the libnvdimm-core. In this update the PMEM driver, on x86, gains the
ability to assert that writes to persistent memory have been flushed all
the way through the caches and buffers in the platform to persistent
media. See memcpy_to_pmem() and wmb_pmem().
BLK:
This new driver enables access to persistent memory media through "Block
Data Windows" as defined by the NFIT. The primary difference of this
driver to PMEM is that only a small window of persistent memory is
mapped into system address space at any given point in time. Per-NVDIMM
windows are reprogrammed at run time, per-I/O, to access different
portions of the media. BLK-mode, by definition, does not support DAX.
BTT:
This is a library, optionally consumed by either PMEM or BLK, that
converts a byte-accessible namespace into a disk with atomic sector
update semantics (prevents sector tearing on crash or power loss). The
sinister aspect of sector tearing is that most applications do not know
they have a atomic sector dependency. At least today's disk's rarely
ever tear sectors and if they do one almost certainly gets a CRC error
on access. NVDIMMs will always tear and always silently. Until an
application is audited to be robust in the presence of sector-tearing
the usage of BTT is recommended.
Thanks to: Ross Zwisler, Jeff Moyer, Vishal Verma, Christoph Hellwig,
Ingo Molnar, Neil Brown, Boaz Harrosh, Robert Elliott, Matthew Wilcox,
Andy Rudoff, Linda Knippers, Toshi Kani, Nicholas Moulin, Rafael
Wysocki, and Bob Moore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VtWG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm
Pull libnvdimm subsystem from Dan Williams:
"The libnvdimm sub-system introduces, in addition to the
libnvdimm-core, 4 drivers / enabling modules:
NFIT:
Instantiates an "nvdimm bus" with the core and registers memory
devices (NVDIMMs) enumerated by the ACPI 6.0 NFIT (NVDIMM Firmware
Interface table).
After registering NVDIMMs the NFIT driver then registers "region"
devices. A libnvdimm-region defines an access mode and the
boundaries of persistent memory media. A region may span multiple
NVDIMMs that are interleaved by the hardware memory controller. In
turn, a libnvdimm-region can be carved into a "namespace" device and
bound to the PMEM or BLK driver which will attach a Linux block
device (disk) interface to the memory.
PMEM:
Initially merged in v4.1 this driver for contiguous spans of
persistent memory address ranges is re-worked to drive
PMEM-namespaces emitted by the libnvdimm-core.
In this update the PMEM driver, on x86, gains the ability to assert
that writes to persistent memory have been flushed all the way
through the caches and buffers in the platform to persistent media.
See memcpy_to_pmem() and wmb_pmem().
BLK:
This new driver enables access to persistent memory media through
"Block Data Windows" as defined by the NFIT. The primary difference
of this driver to PMEM is that only a small window of persistent
memory is mapped into system address space at any given point in
time.
Per-NVDIMM windows are reprogrammed at run time, per-I/O, to access
different portions of the media. BLK-mode, by definition, does not
support DAX.
BTT:
This is a library, optionally consumed by either PMEM or BLK, that
converts a byte-accessible namespace into a disk with atomic sector
update semantics (prevents sector tearing on crash or power loss).
The sinister aspect of sector tearing is that most applications do
not know they have a atomic sector dependency. At least today's
disk's rarely ever tear sectors and if they do one almost certainly
gets a CRC error on access. NVDIMMs will always tear and always
silently. Until an application is audited to be robust in the
presence of sector-tearing the usage of BTT is recommended.
Thanks to: Ross Zwisler, Jeff Moyer, Vishal Verma, Christoph Hellwig,
Ingo Molnar, Neil Brown, Boaz Harrosh, Robert Elliott, Matthew Wilcox,
Andy Rudoff, Linda Knippers, Toshi Kani, Nicholas Moulin, Rafael
Wysocki, and Bob Moore"
* tag 'libnvdimm-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm: (33 commits)
arch, x86: pmem api for ensuring durability of persistent memory updates
libnvdimm: Add sysfs numa_node to NVDIMM devices
libnvdimm: Set numa_node to NVDIMM devices
acpi: Add acpi_map_pxm_to_online_node()
libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only
pmem: flag pmem block devices as non-rotational
libnvdimm: enable iostat
pmem: make_request cleanups
libnvdimm, pmem: fix up max_hw_sectors
libnvdimm, blk: add support for blk integrity
libnvdimm, btt: add support for blk integrity
fs/block_dev.c: skip rw_page if bdev has integrity
libnvdimm: Non-Volatile Devices
tools/testing/nvdimm: libnvdimm unit test infrastructure
libnvdimm, nfit, nd_blk: driver for BLK-mode access persistent memory
nd_btt: atomic sector updates
libnvdimm: infrastructure for btt devices
libnvdimm: write blk label set
libnvdimm: write pmem label set
libnvdimm: blk labels and namespace instantiation
...
|
||
|
Dan Williams
|
b94d5230d0 |
libnvdimm, nfit: initial libnvdimm infrastructure and NFIT support
A struct nvdimm_bus is the anchor device for registering nvdimm resources and interfaces, for example, a character control device, nvdimm devices, and I/O region devices. The ACPI NFIT (NVDIMM Firmware Interface Table) is one possible platform description for such non-volatile memory resources in a system. The nfit.ko driver attaches to the "ACPI0012" device that indicates the presence of the NFIT and parses the table to register a struct nvdimm_bus instance. Cc: <linux-acpi@vger.kernel.org> Cc: Lv Zheng <lv.zheng@intel.com> Cc: Robert Moore <robert.moore@intel.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Jeff Moyer <jmoyer@redhat.com> Acked-by: Christoph Hellwig <hch@lst.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Toshi Kani <toshi.kani@hp.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> |
||
|
Valentin Rothberg
|
f6abdb5029 |
staging: I2O cleanup
Remove the last reference on menuconfig I20 that has been removed by
commit
|
||
|
Mathieu Poirier
|
01081f5ab9 |
coresight: moving to new "hwtracing" directory
Keeping drivers related to HW tracing on ARM, i.e coresight, under "drivers/coresight" doesn't make sense when other architectures start rolling out technologies of the same nature. As such creating a new "drivers/hwtracing" directory where all drivers of the same kind can reside, reducing namespace pollution under "drivers/". Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Oded Gabbay
|
1bacc894c2 |
drivers: Move iommu/ before gpu/ in Makefile
AMD GPU devices are dependent on AMD IOMMU controller functionality to allow the GPU to access a process's virtual memory address space, without the need for pinning the memory. This patch changes the order in the drivers makefile, so iommu/ subsystem is linked before gpu/ subsystem. That way, if the gpu and iommu drivers are compiled inside the kernel image (not as modules), the correct order of device loading is still maintained (iommu module is loaded before gpu module). Signed-off-by: Oded Gabbay <oded.gabbay@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> |
||
|
Linus Torvalds
|
dab363f938 |
Staging patches for 3.19-rc1
Here's the big staging tree pull request for 3.19-rc1. We continued to delete more lines than were added, always a good thing, but not at a huge rate this release, only about 70k lines removed overall mostly from removing the horrid bcm driver. Lots of normal staging driver cleanups and fixes all over the place, well over a thousand of them, the shortlog shows all the horrid details. The "contentious" thing here is the movement of the Android binder code out of staging into the "real" part of the kernel. This is code that has been stable for a few years now and is working as-is in the tens of millions of devices with no issues. Yes, the code is horrid, and the userspace api leaves a lot to be desired, but it's not going to change due to legacy issues that we have no control over. Because so many devices and companies rely on this, and the code is stable, might as well promote it out of staging. This was all discussed at the Linux Plumbers conference, and everyone participating agreed that this was the best way forward. There is work happening to replace the binder code with something new that is happening right now, but I don't expect to see the results of that work for another year at the earliest. If that ever happens, and Android switches over to it, I'll gladly remove this version. As for maintainers, I'll be glad to maintain this code, I've been doing it for the past few years with no problems. I'll send a MAINTAINERS entry for it before 3.19-final is out, still need to talk to the Google developers about if they are willing to help with it or not, last I checked they were, which was good. All of these patches have been in linux-next for a while with no reported issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iEYEABECAAYFAlSPICkACgkQMUfUDdst+yksdwCfSLE9VUy1o2sAPDRe+J3bQced EWEAoL3RtnejKbo5tHS2IT69pLrwiIDS =YXyM -----END PGP SIGNATURE----- Merge tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging driver updates from Greg KH: "Here's the big staging tree pull request for 3.19-rc1. We continued to delete more lines than were added, always a good thing, but not at a huge rate this release, only about 70k lines removed overall mostly from removing the horrid bcm driver. Lots of normal staging driver cleanups and fixes all over the place, well over a thousand of them, the shortlog shows all the horrid details. The "contentious" thing here is the movement of the Android binder code out of staging into the "real" part of the kernel. This is code that has been stable for a few years now and is working as-is in the tens of millions of devices with no issues. Yes, the code is horrid, and the userspace api leaves a lot to be desired, but it's not going to change due to legacy issues that we have no control over. Because so many devices and companies rely on this, and the code is stable, might as well promote it out of staging. This was all discussed at the Linux Plumbers conference, and everyone participating agreed that this was the best way forward. There is work happening to replace the binder code with something new that is happening right now, but I don't expect to see the results of that work for another year at the earliest. If that ever happens, and Android switches over to it, I'll gladly remove this version. As for maintainers, I'll be glad to maintain this code, I've been doing it for the past few years with no problems. I'll send a MAINTAINERS entry for it before 3.19-final is out, still need to talk to the Google developers about if they are willing to help with it or not, last I checked they were, which was good. All of these patches have been in linux-next for a while with no reported issues" * tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1382 commits) Staging: slicoss: Fix long line issues in slicoss.c staging: rtl8712: remove unnecessary else after return staging: comedi: change some printk calls to pr_err staging: rtl8723au: hal: Removed the extra semicolon lustre: Deletion of unnecessary checks before three function calls staging: lustre: fix sparse warnings: static function declaration staging: lustre: fixed sparse warnings related to static declarations staging: unisys: remove duplicate header staging: unisys: remove unneeded structure staging: ft1000 : replace __attribute ((__packed__) with __packed drivers: staging: rtl8192e: Include "asm/unaligned.h" instead of "access_ok.h" in "rtl819x_BAProc.c" Drivers:staging:rtl8192e: Fixed checkpatch warning Drivers:staging:clocking-wizard: Added a newline staging: clocking-wizard: check for a valid clk_name pointer staging: rtl8723au: Hal_InitPGData() avoid unnecessary typecasts staging: rtl8723au: _DisableAnalog(): Avoid zero-init variables unnecessarily staging: rtl8723au: Remove unnecessary wrapper _ResetDigitalProcedure1() staging: rtl8723au: _ResetDigitalProcedure1_92C() reduce code obfuscation staging: rtl8723au: Remove unnecessary wrapper _DisableRFAFEAndResetBB() staging: rtl8723au: _DisableRFAFEAndResetBB8192C(): Reduce code obfuscation ... |
||
|
Pratik Patel
|
a06ae8609b |
coresight: add CoreSight core layer framework
CoreSight components are compliant with the ARM CoreSight architecture specification and can be connected in various topologies to suit a particular SoC tracing needs. These trace components can generally be classified as sources, links and sinks. Trace data produced by one or more sources flows through the intermediate links connecting the source to the currently selected sink. The CoreSight framework provides an interface for the CoreSight trace drivers to register themselves with. It's intended to build up a topological view of the CoreSight components and configure the correct serie of components on user input via sysfs. For eg., when enabling a source, the framework builds up a path consisting of all the components connecting the source to the currently selected sink(s) and enables all of them. The framework also supports switching between available sinks and provides status information to user space applications through the debugfs interface. Signed-off-by: Pratik Patel <pratikp@codeaurora.org> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Greg Kroah-Hartman
|
777783e0ab |
staging: android: binder: move to the "real" part of the kernel
The Android binder code has been "stable" for many years now. No matter what comes in the future, we are going to have to support this API, so might as well move it to the "real" part of the kernel as there's no real work that needs to be done to the existing code. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Linus Torvalds
|
29b88e23a9 |
Driver core patches for 3.17-rc1
Here's the big driver-core pull request for 3.17-rc1. Largest thing in here is the dma-buf rework and fence code, that touched many different subsystems so it was agreed it should go through this tree to handle merge issues. There's also some firmware loading updates, as well as tests added, and a few other tiny changes, the changelog has the details. All have been in linux-next for a long time. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iEYEABECAAYFAlPf1XcACgkQMUfUDdst+ylREACdHLXBa02yLrRzbrONJ+nARuFv JuQAoMN49PD8K9iMQpXqKBvZBsu+iCIY =w8OJ -----END PGP SIGNATURE----- Merge tag 'driver-core-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here's the big driver-core pull request for 3.17-rc1. Largest thing in here is the dma-buf rework and fence code, that touched many different subsystems so it was agreed it should go through this tree to handle merge issues. There's also some firmware loading updates, as well as tests added, and a few other tiny changes, the changelog has the details. All have been in linux-next for a long time" * tag 'driver-core-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits) ARM: imx: Remove references to platform_bus in mxc code firmware loader: Fix _request_firmware_load() return val for fw load abort platform: Remove most references to platform_bus device test: add firmware_class loader test doc: fix minor typos in firmware_class README staging: android: Cleanup style issues Documentation: devres: Sort managed interfaces Documentation: devres: Add devm_kmalloc() et al fs: debugfs: remove trailing whitespace kernfs: kernel-doc warning fix debugfs: Fix corrupted loop in debugfs_remove_recursive stable_kernel_rules: Add pointer to netdev-FAQ for network patches driver core: platform: add device binding path 'driver_override' driver core/platform: remove unused implicit padding in platform_object firmware loader: inform direct failure when udev loader is disabled firmware: replace ALIGN(PAGE_SIZE) by PAGE_ALIGN firmware: read firmware size using i_size_read() firmware loader: allow disabling of udev as firmware loader reservation: add suppport for read-only access using rcu reservation: update api and add some helpers ... Conflicts: drivers/base/platform.c |
||
|
Linus Torvalds
|
2521129a6d |
Char / Misc driver patches for 3.17-rc1
Here's the big driver misc / char pull request for 3.17-rc1. Lots of things in here, the thunderbolt support for Apple laptops, some other new drivers, testing fixes, and other good things. All have been in linux-next for a long time. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iEYEABECAAYFAlPf1LcACgkQMUfUDdst+ymaVwCgqMrKFmpduBufOSFROhxlfB5Q ajsAoNDmIn3pgla+kj23Y5ib20aMi++s =IdIr -----END PGP SIGNATURE----- Merge tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char / misc driver patches from Greg KH: "Here's the big driver misc / char pull request for 3.17-rc1. Lots of things in here, the thunderbolt support for Apple laptops, some other new drivers, testing fixes, and other good things. All have been in linux-next for a long time" * tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (119 commits) misc: bh1780: Introduce the use of devm_kzalloc Lattice ECP3 FPGA: Correct endianness drivers/misc/ti-st: Load firmware from ti-connectivity directory. dt-bindings: extcon: Add support for SM5502 MUIC device extcon: sm5502: Change internal hardware switch according to cable type extcon: sm5502: Detect cable state after completing platform booting extcon: sm5502: Add support new SM5502 extcon device driver extcon: arizona: Get MICVDD against extcon device extcon: Remove unnecessary OOM messages misc: vexpress: Fix sparse non static symbol warnings mei: drop unused hw dependent fw status functions misc: bh1770glc: Use managed functions pcmcia: remove DEFINE_PCI_DEVICE_TABLE usage misc: remove DEFINE_PCI_DEVICE_TABLE usage ipack: Replace DEFINE_PCI_DEVICE_TABLE macro use drivers/char/dsp56k.c: drop check for negativity of unsigned parameter mei: fix return value on disconnect timeout mei: don't schedule suspend in pm idle mei: start disconnect request timer consistently mei: reset client connection state on timeout ... |
||
|
Maarten Lankhorst
|
35fac7e305 |
dma-buf: move to drivers/dma-buf
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com> Acked-by: Sumit Semwal <sumit.semwal@linaro.org> Acked-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Chen, Gong
|
76ac8275f2 |
trace, RAS: Add basic RAS trace event
To avoid confuision and conflict of usage for RAS related trace event, add an unified RAS trace event stub. Start a RAS subsystem menu which will be fleshed out in time, when more features get added to it. Signed-off-by: Chen, Gong <gong.chen@linux.intel.com> Link: http://lkml.kernel.org/r/1402475691-30045-2-git-send-email-gong.chen@linux.intel.com Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Tony Luck <tony.luck@intel.com> |
||
|
Andreas Noever
|
1660315366 |
thunderbolt: Add initial cactus ridge NHI support
Thunderbolt hotplug is supposed to be handled by the firmware. But Apple decided to implement thunderbolt at the operating system level. The firmare only initializes thunderbolt devices that are present at boot time. This driver enables hotplug of thunderbolt of non-chained thunderbolt devices on Apple systems with a cactus ridge controller. This first patch adds the Kconfig file as well the parts of the driver which talk directly to the hardware (that is pci device setup, interrupt handling and RX/TX ring management). Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Linus Torvalds
|
4046136afb |
Char / misc driver patches for 3.16-rc1
Here is the big char / misc driver updates for 3.16-rc1. Lots of different driver updates for a variety of different drivers and minor driver subsystems. All have been in linux-next with no reported issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iEYEABECAAYFAlONWI8ACgkQMUfUDdst+ykvQACdGxTChdEU7edElDAXeelVmu8v D1UAoLDvqwUsN7t5v+WG2wkOvhf5MEA7 =tVMP -----END PGP SIGNATURE----- Merge tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into next Pull char/misc driver patches from Greg KH: "Here is the big char / misc driver update for 3.16-rc1. Lots of different driver updates for a variety of different drivers and minor driver subsystems. All have been in linux-next with no reported issues" * tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (79 commits) hv: use correct order when freeing monitor_pages spmi: of: fixup generic SPMI devicetree binding example applicom: dereferencing NULL on error path misc: genwqe: fix uninitialized return value in genwqe_free_sync_sgl() miscdevice.h: Simple syntax fix to make pointers consistent. MAINTAINERS: Add miscdevice.h to file list for char/misc drivers. mcb: Add support for shared PCI IRQs drivers: Remove duplicate conditionally included subdirs misc: atmel_pwm: only build for supported platforms mei: me: move probe quirk to cfg structure mei: add per device configuration mei: me: read H_CSR after asserting reset mei: me: drop harmful wait optimization mei: me: fix hw ready reset flow mei: fix memory leak of mei_clients array uio: fix vma io range check in mmap drivers: uio_dmem_genirq: Fix memory leak in uio_dmem_genirq_probe() w1: do not unlock unheld list_mutex in __w1_remove_master_device() w1: optional bundling of netlink kernel replies connector: allow multiple messages to be sent in one packet ... |
||
|
Linus Torvalds
|
a727eaf64f |
ARM: SoC driver changes
SoC-near driver changes that we're merging through our tree. Mostly because they depend on other changes we have staged, but in some cases because the driver maintainers preferred that we did it this way. This contains a largeish cleanup series of the omap_l3_noc bus driver, cpuidle rework for Exynos, some reset driver conversions and a long branch of TI EDMA fixes and cleanups, with more to come next release. The TI EDMA cleanups is a shared branch with the dmaengine tree, with a handful of Davinci-specific fixes on top. After discussion at last year's KS (and some more on the mailing lists), we are here adding a drivers/soc directory. The purpose of this is to keep per-vendor shared code that's needed by different drivers but that doesn't fit into the MFD (nor drivers/platform) model. We expect to keep merging contents for this hierarchy through arm-soc so we can keep an eye on what the vendors keep adding here and not making it a free-for-all to shove in crazy stuff. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.14 (GNU/Linux) iQIcBAABAgAGBQJTjOFiAAoJEIwa5zzehBx30RYP/0UE+R8ccdsodunmIDrmQ7QP qFWe1YTWlyXtGBDaPCNfdcU09UYatPKuCv5dJ2ToQCyyFI26PIIhFtnCNXmMuYz+ XPCuqAlJ9hZWx7+j2hXRlyhoZMAaJ5EVVxaK5tnVYXDIfy1Y3xG7i069HD/qGrQp xrV+XofFmpU2VAds6S+SpecFFfYD7n/pJ1bTSgzPfaUsEUyV882dJ3skgs1VpTzQ PnL/0Z2t4ePoP3+6p+F7EnJxemLF5IXrlL0c7hODxQKuMqlzoUluywh6SwOHfCQL u2cc5SFUbbKhExwlGOVibdQMiC0HUOXyRvyYFOIdbv+xNH+Zc/tcoQQ22PWm4Yy1 08qOm3Fr6yw5nH5IT+1wCIFCzJEC/ZHM5B2t+RISFybAMk6Bg1TDYJLmd570zkEL aTLtS5hdmy4h8Ad5FBtwKNyL//6FJJxhbHUu/m0qaE0phq94+78B2M6vbx6757xC kCFlpJsHoN0Tn5c9Q1hpTqI/BHxb4UR7Nf+b8Ox8Veuc9JrS35lzi/rWnGxB5WB0 +1KCA8eih9KXTtksxAte1TmSbMciqW559RUR7dNAPXAMPksY2mJV1I+rg0cRsY3i F90Lnc6LWUM5PYpc4VwiC0sUCLKzTFnpZUELqMOiws3PUblbb0StXuoNo6owbtsK mp1Juxi1n7VhoN9AFVpL =SC+e -----END PGP SIGNATURE----- Merge tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next Pull ARM SoC driver changes from Olof Johansson: "SoC-near driver changes that we're merging through our tree. Mostly because they depend on other changes we have staged, but in some cases because the driver maintainers preferred that we did it this way. This contains a largeish cleanup series of the omap_l3_noc bus driver, cpuidle rework for Exynos, some reset driver conversions and a long branch of TI EDMA fixes and cleanups, with more to come next release. The TI EDMA cleanups is a shared branch with the dmaengine tree, with a handful of Davinci-specific fixes on top. After discussion at last year's KS (and some more on the mailing lists), we are here adding a drivers/soc directory. The purpose of this is to keep per-vendor shared code that's needed by different drivers but that doesn't fit into the MFD (nor drivers/platform) model. We expect to keep merging contents for this hierarchy through arm-soc so we can keep an eye on what the vendors keep adding here and not making it a free-for-all to shove in crazy stuff" * tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits) cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM tty: serial: msm: Remove direct access to GSBI power: reset: keystone-reset: introduce keystone reset driver Documentation: dt: add bindings for keystone pll control controller Documentation: dt: add bindings for keystone reset driver soc: qcom: fix of_device_id table ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos ARM: EXYNOS: Move the driver to drivers/cpuidle directory ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c ARM: EXYNOS: Pass the AFTR callback to the platform_data ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier ARM: EXYNOS: Move the AFTR state function into pm.c ARM: EXYNOS: Encapsulate the AFTR code into a function ARM: EXYNOS: Disable cpuidle for exynos5440 ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle ARM: EXYNOS: Remove ifdef for scu_enable in pm ARM: EXYNOS: Move scu_enable in the cpu_pm notifier ARM: EXYNOS: Use the cpu_pm notifier for pm ... |
||
|
Geert Uytterhoeven
|
2e1c951f5d |
drivers: Remove duplicate conditionally included subdirs
The "macintosh" and "nfs" subdirectories are already traversed unconditionally, so there's no need to keep the conditional entries. The unconditional "macintosh" entry used to depend on CONFIG_PPC_PMAC, but the dependency was dropped in commit |
||
|
Arnd Bergmann
|
34b16f74eb |
Qualcomm ARM Based driver Updates for v3.16
* Introduce drivers/soc directory for misc SoC specific code * Add driver to configure GSBI device -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.10 (GNU/Linux) Comment: GPGTools - https://gpgtools.org iQIcBAABCgAGBQJTf5R9AAoJEF9hYXeAcXzBAvkP/RSUlmSd5CQk85rbcMxIlxUz 46OUrDDPLpj1a/rHj+HQMA9vqW2KkIrqZe5eja9oAup13cqHGms36VLMqXF9Lmjt AqCIYKyJ2+NZ9JMh5+nVSAr2sxlkbLMKjHb7auHyWVvTmgv1zxOPDQrfhqqKnEkY RNmZG8OKc42S3oG2R/h0X2ehlukDG+O+SYOmnSsaQNXPzpVBHY1aPuWBJ0A3vDyq YDggeUoEPw1twWajXtUF/3XIJrOIpQo94qT9daJzlrUtrxwHWHTBI2LMGFch480z fGiJwpwgwX945l+dLW02KWpnOqwhzISPxokIeHdCZemMx8Ntm0mYOi6PX2pul0kO /pAxjmf2B7bq1ykCpW5YSR6bHv+/0Viu3Ra6iJpifm+xDMjQw5CXz/Hi5tB7Og1O dcA2XiIVfhcLfubP35J/IxWR4+2GT7YmcBr93htOFyghuzPiY2Es6sCy1uIPY4jV stvvXKnuCz7bNfQcgHsdSl+mw7qEEC1DpmpVawJCNbuSTYc5ASRESkJwPhX0XZK0 Y0mSwm9noH022oi+TMg31EftMqcpk7dB39tSukz1BkhNlLGk5q6KbuVLV7GDm4dY vyxOKD7GD7hrI0sROy2R6G9qSsaz++p2CvTaj7rr3GQiS/E2ih0bA3OSm/RoxPJM n39EfyrEuNLEPxm5pB8i =Y4iq -----END PGP SIGNATURE----- Merge tag 'qcom-drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/drivers Qualcomm ARM Based driver Updates for v3.16 * Introduce drivers/soc directory for misc SoC specific code * Add driver to configure GSBI device * tag 'qcom-drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom: soc: qcom: Add GSBI driver soc: Introduce drivers/soc place-holder for SOC specific drivers Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
||
|
Santosh Shilimkar
|
3a6e08218f |
soc: Introduce drivers/soc place-holder for SOC specific drivers
Based on earlier thread "https://lkml.org/lkml/2013/10/7/662" and discussion at Kernel Summit'2013, it was agreed to create 'driver/soc' for drivers which are quite SOC specific. Further discussion on the subject is in response to the earlier version of the patch is here: http://lwn.net/Articles/588942/ Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Kumar Gala <galak@codeaurora.org> Cc: Paul Walmsley <paul@pwsan.com> Cc: Olof Johansson <olof@lixom.net> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sandeep Nair <sandeep_n@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Kumar Gala <galak@codeaurora.org> |
||
|
Linus Torvalds
|
f6ce579d91 |
SH Driver Update for v3.15
* Compile drivers/sh/pm_runtime.c if ARCH_SHMOBILE_MULTI This resolves a regression introduced in v3.14 by |
||
|
Geert Uytterhoeven
|
3c90c55dcd |
drivers: sh: compile drivers/sh/pm_runtime.c if ARCH_SHMOBILE_MULTI
If the kernel is built to support multi-ARM configuration with shmobile support built in, then drivers/sh is not built. This contains the PM runtime code in drivers/sh/pm_runtime.c, which implicitly enables the module clocks for all devices, and thus is quite essential. Without this, the state of clocks depends on implicit reset state, or on the bootloader. If ARCH_SHMOBILE_MULTI then build the drivers/sh directory, but ensure that bits that may conflict (drivers/sh/clk if the common clock framework is enabled) or are not used (drivers/sh/intc), are not built. Also, only enable the PM runtime code when actually running on a shmobile SoCs that needs it. ARCH_SHMOBILE_MULTI was added a while ago by commit |
||
|
Tomi Valkeinen
|
f7018c2135 |
video: move fbdev to drivers/video/fbdev
The drivers/video directory is a mess. It contains generic video related files, directories for backlight, console, linux logo, lots of fbdev device drivers, fbdev framework files. Make some order into the chaos by creating drivers/video/fbdev directory, and move all fbdev related files there. No functionality is changed, although I guess it is possible that some subtle Makefile build order related issue could be created by this patch. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Rob Clark <robdclark@gmail.com> Acked-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> |
||
|
Johannes Thumshirn
|
3764e82e51 |
drivers: Introduce MEN Chameleon Bus
The MCB (MEN Chameleon Bus) is a Bus specific to MEN Mikroelektronik FPGA based devices. It is used to identify MCB based IP-Cores within an FPGA and provide the necessary framework for instantiating drivers for these devices. Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Kenneth Heitke
|
5a86bf3439 |
spmi: Linux driver framework for SPMI
System Power Management Interface (SPMI) is a specification developed by the MIPI (Mobile Industry Process Interface) Alliance optimized for the real time control of Power Management ICs (PMIC). SPMI is a two-wire serial interface that supports up to 4 master devices and up to 16 logical slaves. The framework supports message APIs, multiple busses (1 controller per bus) and multiple clients/slave devices per controller. Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org> Signed-off-by: Michael Bohan <mbohan@codeaurora.org> Signed-off-by: Josh Cartwright <joshc@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Laurent Pinchart
|
bf98c1eac1 |
ARM: Rename ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY
SH-Mobile platforms are transitioning from non-multiplatform to multiplatform kernel. A new ARCH_SHMOBILE_MULTI configuration symbol has been created to group all multiplatform-enabled SH-Mobile SoCs. The existing ARCH_SHMOBILE configuration symbol groups SoCs that haven't been converted yet. This arrangement works fine for the arch/ code, but lots of drivers needed on both ARCH_SHMOBILE and ARCH_SHMOBILE_MULTI depend on ARCH_SHMOBILE only. In order to avoid changing them, rename ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY, and create a new boolean ARCH_SHMOBILE configuration symbol that is selected by both ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> |
||
|
Linus Torvalds
|
f9300eaaac |
ACPI and power management updates for 3.13-rc1
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
|
||
|
Srinivas Pandruvada
|
12cc4b3827 |
PowerCap: Add to drivers Kconfig and Makefile
Added changes to Makefile and Kconfig to include in driver build. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
||
|
Kishon Vijay Abraham I
|
ff76496347 |
drivers: phy: add generic PHY framework
The PHY framework provides a set of APIs for the PHY drivers to create/destroy a PHY and APIs for the PHY users to obtain a reference to the PHY with or without using phandle. For dt-boot, the PHY drivers should also register *PHY provider* with the framework. PHY drivers should create the PHY by passing id and ops like init, exit, power_on and power_off. This framework is also pm runtime enabled. The documentation for the generic PHY framework is added in Documentation/phy.txt and the documentation for dt binding can be found at Documentation/devicetree/bindings/phy/phy-bindings.txt Cc: Tomasz Figa <t.figa@samsung.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Linus Torvalds
|
3aa78e0cb5 |
For the 3.11 merge we only have one new MFD driver for the Kontron PLD.
But we also have: - Support for the TPS659038 PMIC from the palmas driver. - Intel's Coleto Creek and Avoton SoCs support from the lpc_ich driver. - RTL8411B support from the rtsx driver. - More DT support for the Arizona, max8998, twl4030-power and the ti_am335x_tsadc drivers. - The SSBI driver move under MFD. - A conversion to the devm_* API for most of the MFD drivers. - The twl4030-power got split from twl-core into its own module. - A major ti_am335x_adc cleanup, leading to a proper DT support. - Our regular arizona and wm* updates and cleanups from the Wolfson folks. - A better error handling and initialization, and a regulator subdevice addition for the 88pm80x driver. - A bulk platform_set_drvdata() call removal that's no longer need since commit |
||
|
Alessandro Rubini
|
9c9f32edde |
FMC: create drivers/fmc and toplevel Kconfig question
This commit creates the drivers/fmc directory and puts the necessary hooks for kbuild and kconfig. The code is currently a placeholder that only registers an empty bus. Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Acked-by: Juan David Gonzalez Cobas <dcobas@cern.ch> Acked-by: Emilio G. Cota <cota@braap.org> Acked-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Arnd Bergmann
|
45fcac1aad |
mfd: Move ssbi driver into drivers/mfd
There is no reason for ssbi to have its own top-level driver directory when the only users of this interface are all MFD drivers. The only mainline driver using it at the moment (PM8921) is marked broken and in fact does not compile. I have verified that fixing the trivial build breakage in pm8921 links in the new ssbi code just fine, but that can be a separate patch. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: David Brown <davidb@codeaurora.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> |
||
|
Linus Torvalds
|
6fa52ed33b |
ARM: arm-soc driver changes for 3.10
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
|
||
|
Linus Torvalds
|
736a2dd257 |
Lots of virtio work which wasn't quite ready for last merge window. Plus
I dived into lguest again, reworking the pagetable code so we can move the switcher page: our fixmaps sometimes take more than 2MB now... Cheers, Rusty. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.12 (GNU/Linux) iQIcBAABAgAGBQJRga7lAAoJENkgDmzRrbjx/yIQAKpqIBtxOJeYH3SY+Uoe7Cfp toNYcpJEldvb0UcWN8M2cSZpHoxl1SUoq9djwcM29tcKa7EZAjHaGtb/Q1qMTDgv +B3WAfiGU2pmXFxLAkbrlLNGnysy24JspqJQ5hcYV84EiBxQdZp+nCYgOphd+GMK ww16vo9ya8jFjzt3GeRp/Heb3vEzV4Cp6BC3i0m8A3WNpEpbRb66pqXNk5o8ggJO SxQOKSXmUM+0m+jKSul5xn3e2Ls2LOrZZ8/DIHA+gW66N4Zab7n2/j1Q9VRxb4lh FqnR7KwgBX8OCh9IsBDqQYS7MohvMYge6eUdLtFrq84jvMleMEhrC8q9v2tucFUb 5t18CLwvyK7Gdg6UCKiZ7YSPcuURAILO16al9bh5IseeBDsuX+43VsvQoBmFn9k6 cLOVTZ6BlOmahK5PyRYFSvLa9Rxzr/05Mr7oYq9UgshD9io78dnqczFYIORF53rW zD7C4HuTZfYJFfNd0wAJ0RfVXnf8QvDlMdo7zPC26DSXNWqj8OexCY0qqSWUB+2F vcfJP6NkV4fZB8aawWIFUVwc64yqtt2uPVLa7ATZWqk16PgKrchGewmw3tiEwOgu 1l7xgffTRRUIJsqaCZoXdgw3yezcKRjuUBcOxL09lDAAhc+NxWNvzZBsKp66DwDk yZQKn0OdXnuf0CeEOfFf =1tYL -----END PGP SIGNATURE----- Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux Pull virtio & lguest updates from Rusty Russell: "Lots of virtio work which wasn't quite ready for last merge window. Plus I dived into lguest again, reworking the pagetable code so we can move the switcher page: our fixmaps sometimes take more than 2MB now..." Ugh. Annoying conflicts with the tcm_vhost -> vhost_scsi rename. Hopefully correctly resolved. * tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (57 commits) caif_virtio: Remove bouncing email addresses lguest: improve code readability in lg_cpu_start. virtio-net: fill only rx queues which are being used lguest: map Switcher below fixmap. lguest: cache last cpu we ran on. lguest: map Switcher text whenever we allocate a new pagetable. lguest: don't share Switcher PTE pages between guests. lguest: expost switcher_pages array (as lg_switcher_pages). lguest: extract shadow PTE walking / allocating. lguest: make check_gpte et. al return bool. lguest: assume Switcher text is a single page. lguest: rename switcher_page to switcher_pages. lguest: remove RESERVE_MEM constant. lguest: check vaddr not pgd for Switcher protection. lguest: prepare to make SWITCHER_ADDR a variable. virtio: console: replace EMFILE with EBUSY for already-open port virtio-scsi: reset virtqueue affinity when doing cpu hotplug virtio-scsi: introduce multiqueue support virtio-scsi: push vq lock/unlock into virtscsi_vq_done virtio-scsi: pass struct virtio_scsi to virtqueue completion function ... |
||
|
Linus Torvalds
|
ec25e246b9 |
USB patches for 3.10-rc1
Here's the big USB pull request for 3.10-rc1. Lots of USB patches here, the majority being USB gadget changes and USB-serial driver cleanups, the rest being ARM build fixes / cleanups, and individual driver updates. We also finally got some chipidea fixes, which have been delayed for a number of kernel releases, as the maintainer has now reappeared. All of these have been in linux-next for a while. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.19 (GNU/Linux) iEYEABECAAYFAlF+md4ACgkQMUfUDdst+ymkSgCfZWIiCtiX/li0yJqSiRB4yYJx Ex0AoNemOOf6ywvSOHPbILTbJ1G+c/PX =JmvB -----END PGP SIGNATURE----- Merge tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB patches from Greg Kroah-Hartman: "Here's the big USB pull request for 3.10-rc1. Lots of USB patches here, the majority being USB gadget changes and USB-serial driver cleanups, the rest being ARM build fixes / cleanups, and individual driver updates. We also finally got some chipidea fixes, which have been delayed for a number of kernel releases, as the maintainer has now reappeared. All of these have been in linux-next for a while" * tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (568 commits) USB: ehci-msm: USB_MSM_OTG needs USB_PHY USB: OHCI: avoid conflicting platform drivers USB: OMAP: ISP1301 needs USB_PHY USB: lpc32xx: ISP1301 needs USB_PHY USB: ftdi_sio: enable two UART ports on ST Microconnect Lite usb: phy: tegra: don't call into tegra-ehci directly usb: phy: phy core cannot yet be a module USB: Fix initconst in ehci driver usb-storage: CY7C68300A chips do not support Cypress ATACB USB: serial: option: Added support Olivetti Olicard 145 USB: ftdi_sio: correct ST Micro Connect Lite PIDs ARM: mxs_defconfig: add CONFIG_USB_PHY ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY usb: phy: remove exported function from __init section usb: gadget: zero: put function instances on unbind usb: gadget: f_sourcesink.c: correct a copy-paste misnomer usb: gadget: cdc2: fix error return code in cdc_do_config() usb: gadget: multi: fix error return code in rndis_do_config() usb: gadget: f_obex: fix error return code in obex_bind() USB: storage: convert to use module_usb_driver() ... |
||
|
Philipp Zabel
|
61fc413176 |
reset: Add reset controller API
This adds a simple API for devices to request being reset by separate reset controller hardware and implements the reset signal device tree binding. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Pavel Machek <pavel@ucw.cz> |
||
|
David Brown
|
ce44bf5b55 |
SSBI: Remove MSM_ prefix from SSBI drivers
Although the SSBI sub is currently only used on MSM SoCs, it is still a bus in its own right. Remove this msm_ prefix from the driver and it's symbols. Clients can now refer directly to ssbi_write() and ssbi_read(). Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Kenneth Heitke
|
e44b0ceee4 |
add single-wire serial bus interface (SSBI) driver
SSBI is the Qualcomm single-wire serial bus interface used to connect the MSM devices to the PMIC and other devices. Since SSBI only supports a single slave, the driver gets the name of the slave device passed in from the board file through the master device's platform data. SSBI registers pretty early (postcore), so that the PMIC can come up before the board init. This is useful if the board init requires the use of gpios that are connected through the PMIC. Based on a patch by Dima Zavin <dima@android.com> that can be found at: http://android.git.kernel.org/?p=kernel/msm.git;a=commitdiff;h=eb060bac4 This patch adds PMIC Arbiter support for the MSM8660. The PMIC Arbiter is a hardware wrapper around the SSBI 2.0 controller that is designed to overcome concurrency issues and security limitations. A controller_type field is added to the platform data to specify the type of the SSBI controller (1.0, 2.0, or PMIC Arbiter). [davidb@codeaurora.org: I've moved this driver into drivers/ssbi/ and added an include for linux/module.h so that it will compile] Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Rusty Russell
|
f87d0fbb57 |
vringh: host-side implementation of virtio rings.
Getting use of virtio rings correct is tricky, and a recent patch saw an implementation of in-kernel rings (as separate from userspace). This abstracts the business of dealing with the virtio ring layout from the access (userspace or direct); to do this, we use function pointers, which gcc inlines correctly. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Michael S. Tsirkin <mst@redhat.com> |
||
|
Felipe Balbi
|
edc7cb2e95 |
usb: phy: make it a menuconfig
We already have a considerable amount of USB PHY drivers, making it a menuconfig just prevents us from adding too much churn to USB's menuconfig. While at that, also select USB_OTG_UTILS from this new menuconfig just to keep backwards compatibility until we manage to remove that symbol. Signed-off-by: Felipe Balbi <balbi@ti.com> |
||
|
Linus Torvalds
|
9d3cae26ac |
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Benjamin Herrenschmidt:
"So from the depth of frozen Minnesota, here's the powerpc pull request
for 3.9. It has a few interesting highlights, in addition to the
usual bunch of bug fixes, minor updates, embedded device tree updates
and new boards:
- Hand tuned asm implementation of SHA1 (by Paulus & Michael
Ellerman)
- Support for Doorbell interrupts on Power8 (kind of fast
thread-thread IPIs) by Ian Munsie
- Long overdue cleanup of the way we handle relocation of our open
firmware trampoline (prom_init.c) on 64-bit by Anton Blanchard
- Support for saving/restoring & context switching the PPR (Processor
Priority Register) on server processors that support it. This
allows the kernel to preserve thread priorities established by
userspace. By Haren Myneni.
- DAWR (new watchpoint facility) support on Power8 by Michael Neuling
- Ability to change the DSCR (Data Stream Control Register) which
controls cache prefetching on a running process via ptrace by
Alexey Kardashevskiy
- Support for context switching the TAR register on Power8 (new
branch target register meant to be used by some new specific
userspace perf event interrupt facility which is yet to be enabled)
by Ian Munsie.
- Improve preservation of the CFAR register (which captures the
origin of a branch) on various exception conditions by Paulus.
- Move the Bestcomm DMA driver from arch powerpc to drivers/dma where
it belongs by Philippe De Muyter
- Support for Transactional Memory on Power8 by Michael Neuling
(based on original work by Matt Evans). For those curious about
the feature, the patch contains a pretty good description."
(See commit db8ff907027b: "powerpc: Documentation for transactional
memory on powerpc" for the mentioned description added to the file
Documentation/powerpc/transactional_memory.txt)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (140 commits)
powerpc/kexec: Disable hard IRQ before kexec
powerpc/85xx: l2sram - Add compatible string for BSC9131 platform
powerpc/85xx: bsc9131 - Correct typo in SDHC device node
powerpc/e500/qemu-e500: enable coreint
powerpc/mpic: allow coreint to be determined by MPIC version
powerpc/fsl_pci: Store the pci ctlr device ptr in the pci ctlr struct
powerpc/85xx: Board support for ppa8548
powerpc/fsl: remove extraneous DIU platform functions
arch/powerpc/platforms/85xx/p1022_ds.c: adjust duplicate test
powerpc: Documentation for transactional memory on powerpc
powerpc: Add transactional memory to pseries and ppc64 defconfigs
powerpc: Add config option for transactional memory
powerpc: Add transactional memory to POWER8 cpu features
powerpc: Add new transactional memory state to the signal context
powerpc: Hook in new transactional memory code
powerpc: Routines for FP/VSX/VMX unavailable during a transaction
powerpc: Add transactional memory unavaliable execption handler
powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes
powerpc: Add FP/VSX and VMX register load functions for transactional memory
powerpc: Add helper functions for transactional memory context switching
...
|
||
|
Linus Torvalds
|
7ed214ac20 |
Char/Misc driver patches for 3.9-rc1
Here's the big char/misc driver patches for 3.9-rc1. Nothing major here, just lots of different driver updates (mei, hyperv, ipack, extcon, vmci, etc.). All of these have been in the linux-next tree for a while. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.19 (GNU/Linux) iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5 x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK =i5HH -----END PGP SIGNATURE----- Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver patches from Greg Kroah-Hartman: "Here's the big char/misc driver patches for 3.9-rc1. Nothing major here, just lots of different driver updates (mei, hyperv, ipack, extcon, vmci, etc.). All of these have been in the linux-next tree for a while." * tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits) w1: w1_therm: Add force-pullup option for "broken" sensors w1: ds2482: Added 1-Wire pull-up support to the driver vme: add missing put_device() after device_register() fails extcon: max8997: Use workqueue to check cable state after completing boot of platform extcon: max8997: Set default UART/USB path on probe extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type extcon: max8997: Set default of ADC debounce time during initialization extcon: max8997: Remove duplicate code related to set H/W line path extcon: max8997: Move defined constant to header file extcon: max77693: Make max77693_extcon_cable static extcon: max8997: Remove unreachable code extcon: max8997: Make max8997_extcon_cable static extcon: max77693: Remove unnecessary goto statement to improve readability extcon: max77693: Convert to devm_input_allocate_device() extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style CREDITS: update email and address of Harald Hoyer extcon: arizona: Use MICDET for final microphone identification extcon: arizona: Always take the first HPDET reading as the final one extcon: arizona: Clear _trig_sts bits after jack detection extcon: arizona: Don't HPDET magic when headphones are enabled ... |
||
|
Rob Herring
|
300586778d |
ARM / highbank: add support for pl320 IPC
The pl320 IPC allows for interprocessor communication between the highbank A9 and the EnergyCore Management Engine. The pl320 implements a straightforward mailbox protocol. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
||
|
Jon Mason
|
fce8a7bb5b |
PCI-Express Non-Transparent Bridge Support
A PCI-Express non-transparent bridge (NTB) is a point-to-point PCIe bus connecting 2 systems, providing electrical isolation between the two subsystems. A non-transparent bridge is functionally similar to a transparent bridge except that both sides of the bridge have their own independent address domains. The host on one side of the bridge will not have the visibility of the complete memory or I/O space on the other side of the bridge. To communicate across the non-transparent bridge, each NTB endpoint has one (or more) apertures exposed to the local system. Writes to these apertures are mirrored to memory on the remote system. Communications can also occur through the use of doorbell registers that initiate interrupts to the alternate domain, and scratch-pad registers accessible from both sides. The NTB device driver is needed to configure these memory windows, doorbell, and scratch-pad registers as well as use them in such a way as they can be turned into a viable communication channel to the remote system. ntb_hw.[ch] determines the usage model (NTB to NTB or NTB to Root Port) and abstracts away the underlying hardware to provide access and a common interface to the doorbell registers, scratch pads, and memory windows. These hardware interfaces are exported so that other, non-mainlined kernel drivers can access these. ntb_transport.[ch] also uses the exported interfaces in ntb_hw.[ch] to setup a communication channel(s) and provide a reliable way of transferring data from one side to the other, which it then exports so that "client" drivers can access them. These client drivers are used to provide a standard kernel interface (i.e., Ethernet device) to NTB, such that Linux can transfer data from one system to the other in a standard way. Signed-off-by: Jon Mason <jon.mason@intel.com> Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Philippe De Muyter
|
9a32299394 |
powerpc, dma: move bestcomm driver from arch/powerpc/sysdev to drivers/dma
The bestcomm dma hardware, and some of its users like the FEC ethernet component, is used in different FreeScale parts, including non-powerpc parts like the ColdFire MCF547x & MCF548x families. Don't keep the driver hidden in arch/powerpc where it is inaccessible for other arches. .c files are moved to drivers/dma/bestcomm, while .h files are moved to include/linux/fsl/bestcomm. Makefiles, Kconfigs and #include directives are updated for the new file locations. Tested by recompiling for MPC5200 with all bestcomm users enabled. Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Anatolij Gustschin <agust@denx.de> |
||
|
Greg Kroah-Hartman
|
05e5027efc |
Staging: ipack: move out of staging
The ipack subsystem is cleaned up enough to now move out of the staging tree, and into drivers/ipack. Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com> Cc: Jens Taprogge <jens.taprogge@taprogge.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Matthew Garrett
|
061475b65c |
IPMI: Change link order
IPMI must be initialised before ACPI in order to ensure that any IPMI services are available before ACPI driver initialisation attempts to use any IPMI operation regions. Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Linus Torvalds
|
aecdc33e11 |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
|
||
|
Linus Torvalds
|
8f446a7a06 |
ARM: soc: driver specific changes
- A long-coming conversion of various platforms to a common LED infrastructure - AT91 is moved over to use the newer MCI driver for MMC - Pincontrol conversions for samsung platforms - DT bindings for gscaler on samsung - i2c driver fixes for tegra, acked by i2c maintainer -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.11 (GNU/Linux) iQIcBAABAgAGBQJQaO48AAoJEIwa5zzehBx3excP/ieEkRhvfnWxdYST6ekvGIQr nEyskOh2rVjgYKmSXUJyKSbvG+7bZ8VIxvPvojeAJ/R84pTFMzbR2F0CaPKzAuSW inDt6c0Bnx1NZlfUTAoXcz7feyq9zHYNs9BCLoPU0bYNchCCqcWSKzqnpXk2ph/P LFnmNa0j6a4E3QJYAjM2zFvc3Tgk+MWTq1fWwNFvsWTh2WbQtmB/iGnzT5Xs4XQh u1SSx5tz0lcF5zQRGmJhXgL5+nnIP4sRwRUBAkpe3Gv5cM6WBVEBRDANa5QpbUL2 RXK5YyCTIln2Me4bPk32zEBLjiZ/WXbmiA2uwoqVgy6XToubemDXd0PtKmjj5tZ1 BkTD1DND7BKBEQnJj/GBECEdvx2FbrKfruoPcJHvXPZ7Svn5Dt/MWYJQIkRFkuhL zlVNoDGWlU8nScGrgmTM56UvWmGWC3UFsWSgdVQNfW9yEva+G1FvRUwUH02Ip5Ad 4r28JFIn6zyjtM99ZHipU6C6Rze2ordC7fl5X5LBLkVOobioblxCAhIhcqkhfKsk rFriNsdfYs7SrJA7mK7GzvaMEJgp/5o1noJKXI7ZBcLI8yYagzbQbPu/vGi6G6d3 0xC7NaTEJbtoXoDAtmtilLRxmw0YCXgVBBGua0K2YKpcRwnzCHNbV4gsLMnDuOXS HP4M96LxLHJlLGCxhEme =ck7M -----END PGP SIGNATURE----- Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM soc driver specific changes from Olof Johansson: - A long-coming conversion of various platforms to a common LED infrastructure - AT91 is moved over to use the newer MCI driver for MMC - Pincontrol conversions for samsung platforms - DT bindings for gscaler on samsung - i2c driver fixes for tegra, acked by i2c maintainer Fix up conflicts as per Olof. * tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits) drivers: bus: omap_l3: use resources instead of hardcoded irqs pinctrl: exynos: Fix wakeup IRQ domain registration check pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data pinctrl: exynos: Correct the detection of wakeup-eint node pinctrl: exynos: Mark exynos_irq_demux_eint as inline pinctrl: exynos: Handle only unmasked wakeup interrupts pinctrl: exynos: Fix typos in gpio/wkup _irq_mask pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa drivers: bus: Move the OMAP interconnect driver to drivers/bus/ i2c: tegra: dynamically control fast clk i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20 ARM: tegra: clock: remove unused clock entry for i2c ARM: tegra: clock: add connection name in i2c clock entry i2c: tegra: pass proper name for getting clock ARM: tegra: clock: add i2c fast clock entry in clock table ARM: EXYNOS: Adds G-Scaler device from Device Tree ARM: EXYNOS: Add clock support for G-Scaler ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used ... |
||
|
Simon Arlott
|
89214f009c |
ARM: bcm2835: add interrupt controller driver
The BCM2835 contains a custom interrupt controller, which supports 72 interrupt sources using a 2-level register scheme. The interrupt controller, or the HW block containing it, is referred to occasionally as "armctrl" in the SoC documentation, hence the symbol naming in the code. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split as of 2012/09/08, and modified as follows: * s/bcm2708/bcm2835/. * Modified device tree vendor prefix. * Moved implementation to drivers/irchip/. * Added devicetree documentation, and hence removed list of IRQs from bcm2835.dtsi. * Changed shift in MAKE_HWIRQ() and HWIRQ_BANK() from 8 to 5 to reduce the size of the hwirq space, and pass the total size of the hwirq space to irq_domain_add_linear(), rather than just the number of valid hwirqs; the two are different due to the hwirq space being sparse. * Added the interrupt controller DT node to the top-level of the DT, rather than nesting it inside a /axi node. Hence, changed the reg value since /axi had a ranges property. This seems simpler to me, but I'm not sure if everyone will like this change or not. * Don't set struct irq_domain_ops.map = irq_domain_simple_map, hence removing the need to patch include/linux/irqdomain.h or kernel/irq/irqdomain.c. * Simplified armctrl_of_init() using of_iomap(). * Removed unused IS_VALID_BANK()/IS_VALID_IRQ() macros. * Renamed armctrl_handle_irq() to prevent possible symbol clashes. * Made armctrl_of_init() static. * Removed comment "Each bank is registered as a separate interrupt controller" since this is no longer true. * Removed FSF address from license header. * Added my name to copyright header. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Dom Cobley <popcornmix@gmail.com> Signed-off-by: Dom Cobley <dc4@broadcom.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Arnd Bergmann <arnd@arndb.de> |
||
|
alex.bluesman.smirnov@gmail.com
|
0739d643b8 |
drivers/ieee802154: move ieee802154 drivers to net folder
The IEEE 802.15.4 standard represents a networking protocol. I don't exactly know why drivers for this protocol are stored into the root 'driver' folder, but better will be to store them with other networking stuff. Currently there are only 3 drivers available for IEEE 802.15.4 stack, so lets do it now with the smallest overhead. Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |