Xen requires all active pagetables to be marked read-only. When the
base of the pagetable is loaded into %cr3, the hypervisor validates
the entire pagetable and only allows the load to proceed if it all
checks out.
This is pretty slow, so to mitigate this cost Xen has a notion of
pinned pagetables. Pinned pagetables are pagetables which are
considered to be active even if no processor's cr3 is pointing to is.
This means that it must remain read-only and all updates are validated
by the hypervisor. This makes context switches much cheaper, because
the hypervisor doesn't need to revalidate the pagetable each time.
This also adds a new paravirt hook which is called during setup once
the zones and memory allocator have been initialized. When the
init_mm pagetable is first built, the struct page array does not yet
exist, and so there's nowhere to put he init_mm pagetable's PG_pinned
flags. Once the zones are initialized and the struct page array
exists, we can set the PG_pinned flags for those pages.
This patch also adds the Xen support for pte pages allocated out of
highmem (highpte) by implementing xen_kmap_atomic_pte.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Zach Amsden <zach@vmware.com>
Put config options for Xen after the core pieces are in place.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Xen maintains a base clock which measures nanoseconds since system
boot. This is provided to guests via a shared page which contains a
base time in ns, a tsc timestamp at that point and tsc frequency
parameters. Guests can compute the current time by reading the tsc
and using it to extrapolate the current time from the basetime. The
hypervisor makes sure that the frequency parameters are updated
regularly, paricularly if the tsc changes rate or stops.
This is implemented as a clocksource, so the interface to the rest of
the kernel is a simple clocksource which simply returns the current
time directly in nanoseconds.
Xen also provides a simple timer mechanism, which allows a timeout to
be set in the future. When that time arrives, a timer event is sent
to the guest. There are two timer interfaces:
- An old one which also delivers a stream of (unused) ticks at 100Hz,
and on the same event, the actual timer events. The 100Hz ticks
cause a lot of spurious wakeups, but are basically harmless.
- The new timer interface doesn't have the 100Hz ticks, and can also
fail if the specified time is in the past.
This code presents the Xen timer as a clockevent driver, and uses the
new interface by preference.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Xen implements interrupts in terms of event channels. Each guest
domain gets 1024 event channels which can be used for a variety of
purposes, such as Xen timer events, inter-domain events,
inter-processor events (IPI) or for real hardware IRQs.
Within the kernel, we map the event channels to IRQs, and implement
the whole interrupt handling using a Xen irq_chip.
Rather than setting NR_IRQ to 1024 under PARAVIRT in order to
accomodate Xen, we create a dynamic mapping between event channels and
IRQs. Ideally, Linux will eventually move towards dynamically
allocating per-irq structures, and we can use a 1:1 mapping between
event channels and irqs.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Xen pagetable handling, including the machinery to implement direct
pagetables.
Xen presents the real CPU's pagetables directly to guests, with no
added shadowing or other layer of abstraction. Naturally this means
the hypervisor must maintain close control over what the guest can put
into the pagetable.
When the guest modifies the pte/pmd/pgd, it must convert its
domain-specific notion of a "physical" pfn into a global machine frame
number (mfn) before inserting the entry into the pagetable. Xen will
check to make sure the domain is allowed to create a mapping of the
given mfn.
Xen also requires that all mappings the guest has of its own active
pagetable are read-only. This is relatively easy to implement in
Linux because all pagetables share the same pte pages for kernel
mappings, so updating the pte in one pagetable will implicitly update
the mapping in all pagetables.
Normally a pagetable becomes active when you point to it with cr3 (or
the Xen equivalent), but when you do so, Xen must check the whole
pagetable for correctness, which is clearly a performance problem.
Xen solves this with pinning which keeps a pagetable effectively
active even if its currently unused, which means that all the normal
update rules are enforced. This means that it need not revalidate the
pagetable when loading cr3.
This patch has a first-cut implementation of pinning, but it is more
fully implemented in a later patch.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
Add the "nosegneg" fake capabilty to the vsyscall page notes. This is
used by the runtime linker to select a glibc version which then
disables negative-offset accesses to the thread-local segment via
%gs. These accesses require emulation in Xen (because segments are
truncated to protect the hypervisor address space) and avoiding them
provides a measurable performance boost.
Signed-off-by: Ian Pratt <ian.pratt@xensource.com>
Signed-off-by: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: Zachary Amsden <zach@vmware.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ulrich Drepper <drepper@redhat.com>
The tsc-based get_scheduled_cycles interface is not a good match for
Xen's runstate accounting, which reports everything in nanoseconds.
This patch replaces this interface with a sched_clock interface, which
matches both Xen and VMI's requirements.
In order to do this, we:
1. replace get_scheduled_cycles with sched_clock
2. hoist cycles_2_ns into a common header
3. update vmi accordingly
One thing to note: because sched_clock is implemented as a weak
function in kernel/sched.c, we must define a real function in order to
override this weak binding. This means the usual paravirt_ops
technique of using an inline function won't work in this case.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Cc: john stultz <johnstul@us.ibm.com>
In a virtual environment, device drivers such as legacy IDE will waste
quite a lot of time probing for their devices which will never appear.
This helper function allows a paravirt implementation to lay claim to
the whole iomem and ioport space, thereby disabling all device drivers
trying to claim IO resources.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
__supported_pte_mask is needed when constructing pte values. Xen
device drivers need to do this to make mappings of foreign pages (ie,
pages granted to us by other domains).
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Make globally leave_mm visible, specifically so that Xen can use it to
shoot-down lazy uses of cr3.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Add a hook so that the paravirt backend knows when the allocator is
ready. This is useful for the obvious reason that the allocator is
available, but the other side-effect of having the bootmem allocator
available is that each page now has an associated "struct page".
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
It's useful to know which mm is allocating a pagetable. Xen uses this
to determine whether the pagetable being added to is pinned or not.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Use existing elfnote.h to generate vsyscall notes, rather than doing
it locally. Changes elfnote.h a bit to suit, since this is the first
asm user, and it wasn't quite right.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.com>
Rather than using a tri-state integer for the wait flag in
call_usermodehelper_exec, define a proper enum, and use that. I've
preserved the integer values so that any callers I've missed should
still work OK.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: David Howells <dhowells@redhat.com>
early_serial_setup was removed from serial.h, but forgot to put in
serial_8250.h
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark variables with uninitialized_var() if such a warning appears,
and analysis proves that the var is initialized properly on all paths
it is used.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (80 commits)
KVM: Use CPU_DYING for disabling virtualization
KVM: Tune hotplug/suspend IPIs
KVM: Keep track of which cpus have virtualization enabled
SMP: Allow smp_call_function_single() to current cpu
i386: Allow smp_call_function_single() to current cpu
x86_64: Allow smp_call_function_single() to current cpu
HOTPLUG: Adapt thermal throttle to CPU_DYING
HOTPLUG: Adapt cpuset hotplug callback to CPU_DYING
HOTPLUG: Add CPU_DYING notifier
KVM: Clean up #includes
KVM: Remove kvmfs in favor of the anonymous inodes source
KVM: SVM: Reliably detect if SVM was disabled by BIOS
KVM: VMX: Remove unnecessary code in vmx_tlb_flush()
KVM: MMU: Fix Wrong tlb flush order
KVM: VMX: Reinitialize the real-mode tss when entering real mode
KVM: Avoid useless memory write when possible
KVM: Fix x86 emulator writeback
KVM: Add support for in-kernel pio handlers
KVM: VMX: Fix interrupt checking on lightweight exit
KVM: Adds support for in-kernel mmio handlers
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Clean away some code inside some non-existent CONFIG ifdefs
[IA64] ar.itc access must really be after xtime_lock.sequence has been read
[IA64] correctly count CPU objects in the ia64/sn hwperf interface
[IA64] arbitary speed tty ioctl support
[IA64] use machvec=dig on hpzx1 platforms
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__init and __initdata stuff used from __devinit one
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let spu_management_ops.enumerate_spus() return the number of found SPEs
and use that information to draw some little helper penguin logos.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-By: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow fbcon to select the primary display adapter using the
fb_is_primary_device() arch-specific helper. If a a primary adapter is
detected, fbcon will unbind the old adapter from the VT layer, then rebind
using the new adapter. This requires that bind_/unbind_con_driver() be made
public.
Because this feature may produce unexpected behavior (from the user's POV),
this must be explicitly enabled in Kconfig.
[akpm@linux-foundation.org: export unbind_con_driver]
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add function helper, fb_is_primary_device(). Given struct fb_info, it will
return a nonzero value if the device is the primary display.
Currently, only the i386 is supported where the function checks for the
IORESOURCE_ROM_SHADOW flag.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update csb337 board specific init to support "new style" rtc-ds1307 code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new i2c framework to load rtc-rs5c372 for the Thecus N2100.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Voipio Riku <Riku.Voipio@movial.fi>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple SPI master driver for Xilinx SPI controller.
No support for multiple masters.
Not using level 1 drivers from EDK.
[akpm@linux-foundation.org: uninlining]
Signed-off-by: Yuri Frolov <yfrolov@ru.mvista.com>
Signed-off-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid dirtying remote cpu's memory if it already has the correct value.
Cc: Andi Kleen <ak@suse.de>
Cc: Konrad Rzeszutek <konrad@darnok.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid dirtying remote cpu's memory if it already has the correct value.
Cc: Andi Kleen <ak@suse.de>
Cc: Konrad Rzeszutek <konrad@darnok.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On large memory configuration with not so fast CPUs the NMI watchdog is
triggered when memory addresses are being gathered and printed. The code
paths for Alt-SysRq-t are sprinkled with touch_nmi_watchdog in various
places but not in this routine (or in the loop that utilizes this
function). The patch has been tested for regression on large CPU+memory
configuration (128 logical CPUs + 224 GB) and 1,2,4,16-CPU sockets with
various memory sizes (1,2,4,6,20).
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on usage and testing over the past couple of years, kprobes on
i386, ia64, powerpc and x86_64 is no longer EXPERIMENTAL.
This is a follow-up to Robert P.J. Day's patch making "Instrumentation
support" non-EXPERIMENTAL:
http://marc.info/?l=linux-kernel&m=118396955423812&w=2
Arch maintainers for sparc64, avr32 and s390 need to take a similar call.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KSYM_NAME_LEN is peculiar in that it does not include the space for the
trailing '\0', forcing all users to use KSYM_NAME_LEN + 1 when allocating
buffer. This is nonsense and error-prone. Moreover, when the caller
forgets that it's very likely to subtly bite back by corrupting the stack
because the last position of the buffer is always cleared to zero.
This patch increments KSYM_NAME_LEN by one and updates code accordingly.
* off-by-one bug in asm-powerpc/kprobes.h::kprobe_lookup_name() macro
is fixed.
* Where MODULE_NAME_LEN and KSYM_NAME_LEN were used together,
MODULE_NAME_LEN was treated as if it didn't include space for the
trailing '\0'. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Paulo Marques <pmarques@grupopie.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the SB1250 DUART, a dual serial port implementation
included in the Broadcom family of SOCs descending from the SiByte SB1250
MIPS64 chip multiprocessor. It is a new implementation replacing the
old-fashioned driver currently present in the linux-mips.org tree. It
supports all the usual features one would expect from a(n asynchronous)
serial driver, including modem line control (as far as hardware supports it
-- there is edge detection logic missing from the DCD and RI lines and the
driver does not implement polling of these lines at the moment), the serial
console, BREAK transmission and reception, including the magic SysRq. The
receive FIFO threshold is not maintained though.
The driver was tested with a SWARM board which uses a BCM1250 SOC (which is
dual MIPS64 CMP) and has both ports of the single DUART implemented wired
externally. Both were tested. Testing included using the ports as
terminal lines at 1200bps (which is the ports minimum), 115200bps and a
couple of random speeds inbetween. The modem lines were verified to
operate correctly. No testing was performed with a use as a network
interface, like with SLIP or PPP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical implementations of PTRACE_POKEDATA go into generic_ptrace_pokedata()
function.
AFAICS, fix bug on xtensa where successful PTRACE_POKEDATA will nevertheless
return EPERM.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kernel OOPSed or BUGed then it probably should be considered as
tainted. Thus, all subsequent OOPSes and SysRq dumps will report the
tainted kernel. This saves a lot of time explaining oddities in the
calltraces.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Added parisc patch from Matthew Wilson -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rolling forward PCMCIA driver, it was discovered that the indentation in
existing one, as well as in BSP side are very odd. This patch is just result
of Lindent run ontop of culprit files.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the kernelcore= parameter for x86.
Once all patches are applied, a new command-line parameter exist and a new
sysctl. This patch adds the necessary documentation.
From: Yasunori Goto <y-goto@jp.fujitsu.com>
When "kernelcore" boot option is specified, kernel can't boot up on ia64
because of an infinite loop. In addition, the parsing code can be handled
in an architecture-independent manner.
This patch uses common code to handle the kernelcore= parameter. It is
only available to architectures that support arch-independent zone-sizing
(i.e. define CONFIG_ARCH_POPULATES_NODE_MAP). Other architectures will
ignore the boot parameter.
[bunk@stusta.de: make cmdline_parse_kernelcore() static]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparse gives us a few of these:
stacktrace.c:69:38: warning: incorrect type in argument 2
(different signedness)
stacktrace.c:69:38: expected unsigned int *skip
Just get rid of the 'skip' argument since it is contained in the
struct stack_trace that gets passed anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
z/VM Unit record character device driver to access VM reader, punch,
and printer.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
