The callers of scsi_send_eh_cmnd are setting the cmnd buffer,
and then scsi_send_eh_cmnd is copying that updated buffer to
the old_cmnd variable. Then after the command runs, we end up
copying that old_cmnd var which has the new cmnd to the scsi
command buffer. When this command gets recent, all types of fun
things happen like getting TUR or START_STOP commands with
data and scatterlists.
This patch made against scsi-rc-fixes, has the callers of
scsi_send_eh_cmnd pass in the command so scsi_send_eh_cmnd
can do the right thing. This should go into 2.6.18 since this
fixes a regression added when we removed some of the scsi_cmnd
fields and replaced them with local variables.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Software must explicitely re-enable extended firmware tracing
after any ISP abort condition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only. If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).
The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a problem where sg is executing a ->nopage operation on a
compound page, it actually calls get_page() on the first page in the
compound rather than the page which is being mapped. The fix is to
select the correct page by indexing into the compound.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The subsystem check in the PAV code is incorrect, it enables PAV
per device instead of per subsystem.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
vt6420 has super-fragile SCR registers which can hang the whole
machine if accessed with the wrong timings. This patch makes sata_via
use SCR registers only during probing and with the same timings as
before (pre new EH), which is proven to work.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements force_pcs module parameter for ata_piix. If 1,
PCS is ignored, 2 honored. As there seem to be quite a few ICHs w/
impaired PCS, this option will be useful for cases where the default
setting doesn't work.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There have been a number of reports regarding some ICH5s failing to
detect devices since the PCS handling update. Analysis shows that
these problems are caused by bogus PCS values from those controllers.
Before the PCS update, the driver didn't honor PCS regs exactly and
probed them in many cases PCS reports no device. Now that PCS is
honored exactly, these hardware problems are visible.
This patch makes ICH5 ignore PCS.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
spectrum_cs: Fix the logic so we error when the device is *not* present!
This fixes firmware upload failures which prevent the driver from
working (the bug is also present in 2.6.17).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A change I made for 2.6.17 and another for 2.6.18 do not work on older
pcnet32 chips which I do not have access to. If the chip is a 79C970 or
79C965, do not try and suspend or check the link status.
I have tested with a 79C970A, 79C971, 79C972, 79C973, 79C975, 79C976,
and 79C978.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I am using a Xircom CEM33 pcmcia NIC which has occasional hardware problems.
If the netdev watchdog detects a transmit timeout, do_reset is called which
msleeps - this is illegal in atomic context.
This patch schedules the timeout handling as a workqueue item.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
while playing with gcc 4.1 -Wextra warnings, I came across this one:
drivers/net/3c515.c:1027: warning: comparison of unsigned expression >= 0 is always true
Since i is unsigned the >= 0 check in the for loop is always true,
so we might spin there forever unless the if condition triggers.
Since i is only used in this loop, this patch changes it to
an integer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes yet another sunsab problem, when console is set to anything
but the first port. The console framework calls sunsab_console_setup
for each port, and we end up setting up a console on a not yet
discovered port, which leads to an Oops. Instead, defer console setup
until the requested port is properly initialized. Tested on an E250
through an RSC console.
Reported by Daniel Smolik <marvin@mydatex.cz>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver's list of HCA firmware revisions to make sure people
running Sinai firmware older than 1.1.0 get a message suggesting a
firmware upgrade. Update the Arbel versions as well while we are at it.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Intersil firmware 1.7.4 (and possibly others) loses the antenna
selection settings when the port is reset.
Signed-off-by: David Acker <dacker@roinet.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug was introduced during the PCMCIA API conversion and broke
spectrum_cs completely.
Tracked down by Fredrik Tolf <fredrik@dolda2000.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced in commit 3d0f0fa0cb:
bounds checking is performed against period[32] while indexing delay[4].
Spotted by Coverity, CID 1376.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move out PCS handling from piix_sata_prereset() into
piix_sata_present_mask() and use it from newly implemented
piix_sata_softreset(). Class codes for devices which are indicated to
be absent by PCS are cleared to ATA_DEV_NONE. This fixes ghost device
problem reported on ICH6 and 7.
This patch moves PCS handling from prereset to softreset, which makes
two behavior changes.
* perform softreset even when PCS indicates no device
* PCS handling is repeated before retrying softresets due to reset
failures.
Both behavior changes are intended and more consistent with how other
drivers behave.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
One of my recent changes broke C101 carrier handling, this patch
fixes it. Also fixes an old TX underrun checking bug.
2.6.18 material. Please apply.
Thanks.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch should update the fs_enet infrastructure to utilize Phy Abstraction
Layer subsystem. Along with the above, there are apparent bugfixes, overhaul
and improvements.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc. information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
qeth: bhs must be disabled when accessing neighbour tables.
=================================
[ INFO: inconsistent lock state ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@axis.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool -g (show ring sizes) support to the Spidernet network driver.
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unclear how these bugs arrived, presumably from incorrect cleanup of
the 16-bit-only paths, but smc91x wouldn't build for OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It looks like broken BIOSes controlling Rhine chips will remain in use in
significant numbers; such systems fail to come up via PXE after they have
been put into D3 (power-saving) mode.
This patch adds a module option for disabling the call that puts the chip
to sleep.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Joerg Bashir <brak@archive.org>
Cc: Tim Phipps <tim@phipps-hutton.freeserve.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When booting using root-nfs, I'm seeing (independently) two lockdep dumps
in the smc91x driver. The patch below fixes both. Both dumps look like
real locking issues.
Nico - please review and ack if you think the patch is correct.
Dump 1:
Sending DHCP requests .
=================================
[ INFO: inconsistent lock state ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The poll_enable should be in init_registers before enabling interrupts, not
in tx_timeout. Thanks for spotting it Roger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Cc: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add NAPI support to the via-rhine driver so that it can handle higher
speeds and doesn't get overloaded by interrupts as easily.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x driver forgets to release the spinlock on spurious interrupts.
This little patch fixes it.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add netconsole support to dm9000 driver.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sparc32:
drivers/net/s2io.c:2636: warning: implicit declaration of function 'disable_irq'
drivers/net/s2io.c:2656: warning: implicit declaration of function 'enable_irq'
Cc: Ananda Raju <Ananda.Raju@neterion.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device. This patch provides driver for the device.
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/sundance.c:110: error: version causes a section type conflict
I don't understand this error. It's referred to from both __init and
__devinit code. With CONFIG_HOTPLUG=n, version[] is placed in .init.data and
is referred to from .init.text.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
