* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Fix an offset error when reading the CS89x0 ADD_PORT register
[PATCH] spidernet: poor network performance
[PATCH] Spidernet: remove ETH_ZLEN check in earlier patch
[PATCH] bonding: fix an oops when slave device does not provide get_stats
[PATCH] drivers/net: SAA9730: Fix build error
Revert "[PATCH] zd1211rw: Removed unneeded packed attributes"
[PATCH] zd1211rw: Fix of a locking bug
[PATCH] softmac: remove netif_tx_disable when scanning
[PATCH] ieee80211: Fix kernel panic when QoS is enabled
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
On devices with hard_header_len > LL_MAX_HEADER ip_route_me_harder()
reallocates the skb, leading to memory corruption when using the stale
tcph pointer to update the checksum.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of __{ip,nf}_conntrack_expect_find() don't expect that
it increments the reference count of expectation.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NFA_NEST exceeds the skb size the protocol reference is leaked.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The found helper cannot be assigned to conntrack after unlocking
nf_conntrack_lock. This tries to find helper to assign again.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the bug which doesn't assign helper to newly created
conntrack via nf_conntrack_netlink.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the scan section of ieee80211softmac, network transmits are
disabled. When SoftMAC re-enables transmits, it may override the
wishes of a driver that may have very good reasons for disabling
transmits. At least one failure in bcm43xx can be traced to this
problem. In addition, several unexplained problems may arise from
the unexpected enabling of transmits. Note that making this change
introduces a new bug that would allow transmits for the current session
to be transmitted on the wrong channel; however, the new bug is much
less severe than the one being fixed, as the new one only leads to
a few retransmits, whereas the old one can bring the interface down.
A fix that will not introduce new bugs is being investigated; however,
the current, more serious one should be fixed now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When application uses XFRM_MSG_GETSA to get state entry through
netlink socket and kernel has no matching one, the application expects
reply message with error status by kernel.
Kernel doesn't send the message back in the case of Mobile IPv6 route
optimization protocols (i.e. routing header or destination options
header). This is caused by incorrect return code "0" from
net/xfrm/xfrm_user.c(xfrm_user_state_lookup) and it makes kernel skip
to acknowledge at net/netlink/af_netlink.c(netlink_rcv_skb).
This patch fix to reply ESRCH to application.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: TAKAMIYA Noriaki <takamiya@po.ntts.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of kfifo_alloc() should be checked by IS_ERR().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make udp_encap_rcv use pskb_may_pull
IPsec with NAT-T breaks on some notebooks using the latest e1000 chipset,
when header split is enabled. When receiving sufficiently large packets, the
driver puts everything up to and including the UDP header into the header
portion of the skb, and the rest goes into the paged part. udp_encap_rcv
forgets to use pskb_may_pull, and fails to decapsulate it. Instead, it
passes it up it to the IKE daemon.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
H.323 connection tracking code calls ip_ct_refresh_acct() when
processing RCFs and URQs but passes NULL as the skb.
When CONFIG_IP_NF_CT_ACCT is enabled, the connection tracking core tries
to derefence the skb, which results in an obvious panic.
A similar fix was applied on the SIP connection tracking code some time
ago.
Signed-off-by: Faidon Liambotis <paravoid@debian.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP and RAW do not have this issue. Closes Bug #7432.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "u16 *" derefs of skb->data need to be wrapped inside of
a get_unaligned().
Thanks to Gustavo Zacarias for the bug report.
Signed-off-by: David S. Miller <davem@davemloft.net>
I actually dont have a test case for these; i just found them by
inspection. Refer to patch "[XFRM]: Sub-policies broke policy events"
for more info
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XFRM policy events are broken when sub-policy feature is turned on.
A simple test to verify this:
run ip xfrm mon on one window and add then delete a policy on another
window ..
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any L2CAP connection in disconnecting state shall not response
to any further config requests from the remote side. So in case
such a request is received, ignore it.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When sending a positive config response it shall include the actual
MTU to be used on this channel. This differs from the Bluetooth 1.1
specification where it was enough to acknowledge the config request.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the RFCOMM session is no longer attached to the TTY device, then it
makes no sense to go through with changing the termios settings.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After an inquiry completed or got canceled the Bluetooth core should
check for any pending connect attempts.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To receive uvents for the low-level ACL and SCO links, they must be
assigned to a subsystem. It is enough to attach them to the already
established Bluetooth bus.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RFC4191 explicitly states that the procedures are applicable to
hosts only. We should not have changed behavior of routers.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Only routers in "FAILED" state should be considered unreachable.
Otherwise, we do not try to use speicific routes unless all least specific
routers are considered unreachable.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Fix up tcp_mem initial settings to take into account the size of the
hash entries (different on SMP and non-SMP systems).
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
nexthdr is NEXTHDR_FRAGMENT, the nexthdr value from the fragment header
is hp->nexthdr.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patch by James D. Nurmi:
I've got some code very dependant on nfnetlink_queue, and turned up a
large number of warns coming from skb_trim. While it's quite possibly
my code, having not seen it on older kernels made me a bit suspect.
Anyhow, based on some googling I turned up this thread:
http://lkml.org/lkml/2006/8/13/56
And believe the issue to be related, so attached is a small patch to
the kernel -- not sure if this is completely correct, but for anyone
else hitting the WARN_ON(1) in skbuff.h, it might be helpful..
Signed-off-by: James D. Nurmi <jdnurmi@gmail.com>
Ported to ip6_queue and nfnetlink_queue and added return value
checks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFULA_SEQ_GLOBAL should be in network byteorder.
Spotted by Al Viro.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.11 header length is affected by the wireless mode (WDS or not) and
type (QoS or not). We should use the variable hdr_len instead of the
hard coded IEEE80211_3ADDR_LEN, otherwise we may touch invalid memory.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- make sure port in FTP data is in network order (in fact it was looking
buggy for big endian boxes before Viro's changes)
- htonl -> htons for port
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some fixes to endianess problems spotted by Al Viro.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since pskb_copy tacks on the non-linear bits from the original
skb, it needs to count them in the truesize field of the new skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we can hit paths that (legally) do multiple deletes on the
same node and OOPS with the HLIST poison values there instead of
NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes consideration of high memory when determining TCP
hash table sizes. Taking into account high memory results in tcp_mem
values that are too large.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
auth_domain_put() forgot to unlock acquired spinlock.
Cc: Olaf Kirch <okir@monad.swb.de>
Cc: Andy Adamson <andros@citi.umich.edu>
Cc: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
> the build with the attached .config failed, make ends with:
> ...
> : undefined reference to `cipso_v4_sock_getattr'
> net/built-in.o: In function `netlbl_socket_getattr':
...
It looks like I was stupid and made NetLabel depend on CONFIG_NET and not
CONFIG_INET, the patch below should fix this by making NetLabel depend on
CONFIG_INET and CONFIG_SECURITY. Please review and apply for 2.6.19.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It would be nice to keep things working even with this built as a
module, it took me some time to realize my IPv6 tunnel was broken
because of the missing sit module. This module alias fixes things
until distributions have added an appropriate alias to modprobe.conf.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If inet6_init() fails later than ndisc_init() call, or IPv6 module is
unloaded, ndisc_netdev_notifier call remains in the list and will follows in
oops later.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have seen a couple of __alloc_pages() failures due to
fragmentation, there is plenty of free memory but no large order pages
available. I think the problem is in sock_alloc_send_pskb(), the
gfp_mask includes __GFP_REPEAT but its never used/passed to the page
allocator. Shouldnt the gfp_mask be passed to alloc_skb() ?
Signed-off-by: Larry Woodman <lwoodman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
open-coded variant there works only for little-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
htons() is not needed (and no, it's not misspelled ntohs() -
userland expects net-endian here).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculation of IPX checksum got buggered about 2.4.0. The old variant
mangled the packet; that got fixed, but calculation itself got buggered.
Restored the correct logics, fixed a subtle breakage we used to have even
back then: if the sum is 0 mod 0xffff, we want to return 0, not 0xffff.
The latter has special meaning for IPX (cheksum disabled). Observation
(and obvious fix) nicked from history of FreeBSD ipx_cksum.c...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/bridge/netfilter/ebtables.c: In function 'ebt_dev_check':
net/bridge/netfilter/ebtables.c:89: warning: initialization discards qualifiers from pointer target type
So make the char* a const char * and the warning is gone.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
In theory these are opaque 32bit values. However, we end up
allocating them sequentially in host-endian and stick unchanged
on the wire.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setting of the default congestion control was buried in
the sysctl code so it would not be done properly if SYSCTL was
not enabled.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct order is: NULL check before dereference
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ieee80211: Workaround malformed 802.11 frames from AP" patch (see
http://kernel.org/git/?p=linux/kernel/git/linville/wireless-2.6.git;a=commit;h=f09fc44d8c25f22c4d985bb93857338ed02feac6 )
fixes the problem with some buggy APs but also converts debug message into
an error one. This floods the log with errors when you are near such AP (you
get a message for every beacon). This patch reverts the error message back
to the debug one.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I don't want my code to downgraded to GPLv3 because of
cut-n-pasted the comments. These files which I hold copyright
on were started before it was clear what GPLv3 was going to be.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's a bug in the seqfile show operation for flowlabel objects, where
each hash chain is traversed cumulatively for each element. The following
function is called for each element of each chain:
static void ip6fl_fl_seq_show(struct seq_file *seq, struct ip6_flowlabel *fl)
{
while(fl) {
seq_printf...
fl = fl->next;
}
}
Thus, objects can appear mutliple times when reading
/proc/net/ip6_flowlabel, as the above is called for each element in the
chain.
The solution is to remove the while() loop from the above, and traverse
each chain exactly once, per the patch below. This also removes the
ip6fl_fl_seq_show() function, which does nothing else.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when an application requests a lease for a flowlabel via the
IPV6_FLOWLABEL_MGR socket option, no error is returned if an invalid type
of destination address is supplied as part of the request, leading to a
silent failure. This patch ensures that EINVAL is returned to the
application in this case.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time SCTP creates a temporary association, the stack hashes it,
puts it on a list of endpoint associations and increments the backlog.
However, the lifetime of a temporary association is the processing time
of a current packet and it's destroyed after that. In fact, we don't
really want anyone else finding this association. There is no reason to
do this extra work.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make SCTP 1-1 style and peeled-off associations behave like TCP when
setting IP id. In both cases, we set the inet_sk(sk)->daddr and initialize
inet_sk(sk)->id to a random value.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes two changes to protect applications from either removing or
tampering with the CIPSOv4 IP option on a socket. The first is the requirement
that applications have the CAP_NET_RAW capability to set an IPOPT_CIPSO option
on a socket; this prevents untrusted applications from setting their own
CIPSOv4 security attributes on the packets they send. The second change is to
SELinux and it prevents applications from setting any IPv4 options when there
is an IPOPT_CIPSO option already present on the socket; this prevents
applications from removing CIPSOv4 security attributes from the packets they
send.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes bug in iptables modules refcounting on compat error way.
As we are getting modules in check_compat_entry_size_and_hooks(), in case of
later error, we should put them all in translate_compat_table(), not in the
compat_copy_entry_from_user() or compat_copy_match_from_user(), as it is now.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Acked-by: Vasily Averin <vvs@openvz.org>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing unlock in get_next_corpse() in nf_conntrack. It was missed
during the removal of listhelp.h . Also remove an unneeded use of
nf_ct_tuplehash_to_ctrack() in the same function.
Should be applied before 2.6.19 is released.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds forgotten compat_flush_offset() call to error way of
translate_compat_table(). May lead to table corruption on the next
compat_do_replace().
Signed-off-by: Vasily Averin <vvs@openvz.org>
Acked-by: Dmitry Mishin <dim@openvz.org>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a number of issues in parsing user-provided table in
translate_table(). Malicious user with CAP_NET_ADMIN may crash system by
passing special-crafted table to the *_tables.
The first issue is that mark_source_chains() function is called before entry
content checks. In case of standard target, mark_source_chains() function
uses t->verdict field in order to determine new position. But the check, that
this field leads no further, than the table end, is in check_entry(), which
is called later, than mark_source_chains().
The second issue, that there is no check that target_offset points inside
entry. If so, *_ITERATE_MATCH macro will follow further, than the entry
ends. As a result, we'll have oops or memory disclosure.
And the third issue, that there is no check that the target is completely
inside entry. Results are the same, as in previous issue.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bug in the seqfile handling for /proc/net/ip6_flowlabel, where,
after finding a flowlabel, the code will loop forever not finding any
further flowlabels, first traversing the rest of the hash bucket then just
looping.
This patch fixes the problem by breaking after the hash bucket has been
traversed.
Note that this bug can cause lockups and oopses, and is trivially invoked
by an unpriveleged user.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was looking at a RHEL5 bug report involving Xen and SCTP
(https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=212550).
It turns out that SCTP wasn't written to handle skb fragments at
all. The absence of any calls to skb_may_pull is testament to
that.
It just so happens that Xen creates fragmented packets more often
than other scenarios (header & data split when going from domU to
dom0). That's what caused this bug to show up.
Until someone has the time sits down and audits the entire net/sctp
directory, here is a conservative and safe solution that simply
linearises all packets on input.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings:
build2.out:net/dccp/ccids/ccid2.c:355: warning: long long unsigned int format, u64 arg (arg 3)
build2.out:net/dccp/ccids/ccid2.c:360: warning: long long unsigned int format, u64 arg (arg 3)
build2.out:net/dccp/ccids/ccid2.c:482: warning: long long unsigned int format, u64 arg (arg 5)
build2.out:net/dccp/ccids/ccid2.c:639: warning: long long unsigned int format, u64 arg (arg 3)
build2.out:net/dccp/ccids/ccid2.c:639: warning: long long unsigned int format, u64 arg (arg 4)
build2.out:net/dccp/ccids/ccid2.c:674: warning: long long unsigned int format, u64 arg (arg 3)
build2.out:net/dccp/ccids/ccid2.c:720: warning: long long unsigned int format, u64 arg (arg 3)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_segment fails to segment linear packets correctly because it
tries to write all linear parts of the original skb into each
segment. This will always panic as each segment only contains
enough space for one MSS.
This was not detected earlier because linear packets should be
rare for GSO. In fact it still remains to be seen what exactly
created the linear packets that triggered this bug. Basically
the only time this should happen is if someone enables GSO
emulation on an interface that does not support SG.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use memcpy() to move xfrm_address_t objects in and out
of netlink messages. The vast majority of xfrm_user was
doing this properly, except for copy_from_user_state()
and copy_to_user_state().
Signed-off-by: David S. Miller <davem@davemloft.net>
atrtr_find() can return NULL, so do not blindly dereference
rt->dev before we check for rt being NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch fixed a problem which would occur when the refcount on an
auth_domain reached zero. This problem has not been reported in practice
despite existing in two major kernel releases because the refcount can
never reach zero.
This patch fixes the problems that stop the refcount reaching zero.
1/ We were adding to the refcount when inserting in the hash table,
but only removing from the hashtable when the refcount reached zero.
Obviously it never would. So don't count the implied reference of
being in the hash table.
2/ There are two paths on which a socket can be destroyed. One called
svcauth_unix_info_release(). The other didn't. So when the other was
taken, we can lose a reference to an ip_map which in-turn holds a
reference to an auth_domain
So unify the exit paths into svc_sock_put. This highlights the fact
that svc_delete_socket has slightly odd semantics - it does not drop
a reference but probably should. Fixing this need a bit more
thought and testing.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When using H-TCP with a single flow on a 500Mbit connection (or less
actually), alpha can exceed 65000, so alpha needs to be a u32.
Signed-off-by: Gavin McCullagh <gavin.mccullagh@nuim.ie>
Signed-off-by: Doug Leith <doug.leith@nuim.ie>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Leith observed a discrepancy between the version of CUBIC described
in the papers and the version in 2.6.18. A math error related to scaling
causes Cubic to grow too slowly.
Patch is from "Sangtae Ha" <sha2@ncsu.edu>. I validated that
it does fix the problems.
See the following to show behavior over 500ms 100 Mbit link.
Sender (2.6.19-rc3) --- Bridge (2.6.18-rt7) ------- Receiver (2.6.19-rc3)
1G [netem] 100M
http://developer.osdl.org/shemminger/tcp/2.6.19-rc3/cubic-orig.pnghttp://developer.osdl.org/shemminger/tcp/2.6.19-rc3/cubic-fix.png
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CRYPTO_MANAGER is selected automatically by CONFIG_ECB and CONFIG_CBC.
config CRYPTO_ECB
tristate "ECB support"
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
I've added CONFIG_ECB to the ones you mentioned and CONFIG_CBC to
gssapi.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Updates the references to spec documents throughout the code, taking into
account that
* the DCCP, CCID 2, and CCID 3 drafts all became RFCs in March this year
* RFC 1063 was obsoleted by RFC 1191
* draft-ietf-tcpimpl-pmtud-0x.txt was published as an Informational
RFC, RFC 2923 on 2000-09-22.
All references verified.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Mark Dowd <Mark_Dowd@McAfee.com>, ip6_tables is susceptible
to a fragmentation attack causing false negatives on extension header matches.
When extension headers occur in the non-first fragment after the fragment
header (possibly with an incorrect nexthdr value in the fragment header)
a rule looking for this extension header will never match.
Drop fragments that are at offset 0 and don't contain the final protocol
header regardless of the ruleset, since this should not happen normally.
Since all extension headers are before the protocol header this makes sure
an extension header is either not present or in the first fragment, where
we can properly parse it.
With help from Yasuyuki KOZAKAI <yasuyuki.kozakai@toshiba.co.jp>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Mark Dowd <Mark_Dowd@McAfee.com>, ip6_tables is susceptible
to a fragmentation attack causing false negatives on protocol matches.
When the protocol header doesn't follow the fragment header immediately,
the fragment header contains the protocol number of the next extension
header. When the extension header and the protocol header are sent in
a second fragment a rule like "ip6tables .. -p udp -j DROP" will never
match.
Drop fragments that are at offset 0 and don't contain the final protocol
header regardless of the ruleset, since this should not happen normally.
With help from Yasuyuki KOZAKAI <yasuyuki.kozakai@toshiba.co.jp>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_state_num needs to be increased for XFRM_STATE_ACQ states created
by xfrm_state_find() to prevent the counter from going negative when
the state is destroyed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
memcpy 4 bytes to address of auto unsigned long variable followed
by comparison with u32 is a bloody bad idea.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The networking emulator can queue SKBs for a very long
time, so if you're using netem on the sender side for
large bandwidth/delay product testing, the SKB socket
send queue sizes become artificially larger.
Correct this by calling skb_orphan() in netem_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a patch from Jesper Juhl. Try to match the
TCP IPv6 code this was copied from as much as possible,
so that it's easy to see where to add the ipv6 pktoptions
support code.
Signed-off-by: David S. Miller <davem@davemloft.net>
I think I got the cause for the Oops observed in
http://www.mail-archive.com/dccp@vger.kernel.org/msg00578.html
The problem is always with applications listening on PF_INET6 sockets. Apart
from the mentioned oops, I observed another one one, triggered at irregular
intervals via timer interrupt:
run_timer_softirq -> dccp_keepalive_timer
-> inet_csk_reqsk_queue_prune
-> reqsk_free
-> dccp_v6_reqsk_destructor
The latter function is the problem and is also the last function to be called
in said kernel panic.
In any case, there is a real problem with allocating the right request_sock
which is what this patch tackles.
It fixes the following problem:
- application listens on PF_INET6
- DCCPv4 packet comes in, is handed over to dccp_v4_do_rcv, from there
to dccp_v4_conn_request
Now: socket is PF_INET6, packet is IPv4. The following code then furnishes the
connection with IPv6 - request_sock operations:
req = reqsk_alloc(sk->sk_prot->rsk_prot);
The first problem is that all further incoming packets will get a Reset since
the connection can not be looked up.
The second problem is worse:
--> reqsk_alloc is called instead of inet6_reqsk_alloc
--> consequently inet6_rsk_offset is never set (dangling pointer)
--> the request_sock_ops are nevertheless still dccp6_request_ops
--> destructor is called via reqsk_free
--> dccp_v6_reqsk_destructor tries to free random memory location (inet6_rsk_offset not set)
--> panic
I have tested this for a while, DCCP sockets are now handled correctly in all
three scenarios (v4/v6 only/v4-mapped).
Commiter note: I've added the dccp_request_sock_ops forward declaration to keep
the tree building and to reduce the size of the patch for 2.6.19,
later I'll move the functions to the top of the affected source
code to match what we have in the TCP counterpart, where this
problem hasn't existed in the first place, dumb me not to have
done the same thing on DCCP land 8)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (36 commits)
[Bluetooth] Fix HID disconnect NULL pointer dereference
[Bluetooth] Add missing entry for Nokia DTL-4 PCMCIA card
[Bluetooth] Add support for newer ANYCOM USB dongles
[NET]: Can use __get_cpu_var() instead of per_cpu() in loopback driver.
[IPV4] inet_peer: Group together avl_left, avl_right, v4daddr to speedup lookups on some CPUS
[TCP]: One NET_INC_STATS() could be NET_INC_STATS_BH in tcp_v4_err()
[NETFILTER]: Missing check for CAP_NET_ADMIN in iptables compat layer
[NETPOLL]: initialize skb for UDP
[IPV6]: Fix route.c warnings when multiple tables are disabled.
[TG3]: Bump driver version and release date.
[TG3]: Add lower bound checks for tx ring size.
[TG3]: Fix set ring params tx ring size implementation
[NET]: reduce per cpu ram used for loopback stats
[IPv6] route: Fix prohibit and blackhole routing decision
[DECNET]: Fix input routing bug
[TCP]: Bound TSO defer time
[IPv4] fib: Remove unused fib_config members
[IPV6]: Always copy rt->u.dst.error when copying a rt6_info.
[IPV6]: Make IPV6_SUBTREES depend on IPV6_MULTIPLE_TABLES.
[IPV6]: Clean up BACKTRACK().
...
This patch is suitable for just about any 2.6 kernel. It should go in
2.6.19 and 2.6.18.2 and possible even the .17 and .16 stable series.
This is a long standing bug that seems to have only recently become
apparent, presumably due to increasing use of NFS over TCP - many
distros seem to be making it the default.
The SK_CONN bit gets set when a listening socket may be ready
for an accept, just as SK_DATA is set when data may be available.
It is entirely possible for svc_tcp_accept to be called with neither
of these set. It doesn't happen often but there is a small race in
svc_sock_enqueue as SK_CONN and SK_DATA are tested outside the
spin_lock. They could be cleared immediately after the test and
before the lock is gained.
This normally shouldn't be a problem. The sockets are non-blocking so
trying to read() or accept() when ther is nothing to do is not a problem.
However: svc_tcp_recvfrom makes the decision "Should I accept() or
should I read()" based on whether SK_CONN is set or not. This usually
works but is not safe. The decision should be based on whether it is
a TCP_LISTEN socket or a TCP_CONNECTED socket.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: <stable@kernel.org>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Yes, this actually passed tests the way it was.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When submitting a request to a fast portmapper (such as the local rpcbind
daemon), the request can complete before the parent task is even queued up on
xprt->binding. Fix this by queuing before submitting the rpcbind request.
Test plan:
Connectathon locking test with UDP.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The latest HID disconnect sequence change introduced a NULL pointer
dereference. For the quirk to handle buggy remote HID implementations,
it is enough to wait for a potential control channel disconnect from
the remote side and it is also enough to wait only 500 msecs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
I believe this NET_INC_STATS() call can be replaced by
NET_INC_STATS_BH(), a little bit cheaper.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 32bit compatibility layer has no CAP_NET_ADMIN check in
compat_do_ipt_get_ctl, which for example allows to list the current
iptables rules even without having that capability (the non-compat
version requires it). Other capabilities might be required to exploit
the bug (eg. CAP_NET_RAW to get the nfnetlink socket?), so a plain user
can't exploit it, but a setup actually using the posix capability system
might very well hit such a constellation of granted capabilities.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to fully initialize skb to keep lower layers and queueing happy.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
WE-21 changed the ABI for the SIOC[SG]IW{ESSID,NICKN} ioctls by dropping
NULL termination. This patch adds compatibility code so that WE-21 can
work properly with WE-20 (and older) tools.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lookups resolving to ip6_blk_hole_entry must result in silently
discarding the packets whereas an ip6_pkt_prohibit_entry is
supposed to cause an ICMPV6_ADM_PROHIBITED message to be sent.
Thanks to Kim Nordlund <kim.nordlund@nokia.com> for noticing
this bug.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a silly bug that has been in the input routing code
for some time. It results in trying to send to a node directly when
the origin of the packet is via the default router.
Its been tested by Alan Kemmerer <alan.kemmerer@mittalsteel.com> who
reported the bug and its a fairly obvious fix for a typo.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Patrick Caulfield <patrick@tykepenguin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch limits the amount of time you will defer sending a TSO segment
to less than two clock ticks, or the time between two acks, whichever is
longer.
On slow links, deferring causes significant bursts. See attached plots,
which show RTT through a 1 Mbps link with a 100 ms RTT and ~100 ms queue
for (a) non-TSO, (b) currnet TSO, and (c) patched TSO. This burstiness
causes significant jitter, tends to overflow queues early (bad for short
queues), and makes delay-based congestion control more difficult.
Deferring by a couple clock ticks I believe will have a relatively small
impact on performance.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
As IPV6_SUBTREES can't work without IPV6_MULTIPLE_TABLES have IPV6_SUBTREES
depend on it.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fn check is unnecessary as fn can never be NULL in BACKTRACK().
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ip6_route_output() never returns NULL, error checking must be done by
looking at dst->error in stead of comparing dst against NULL.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch causes TIPC to return an error message when it receives
an unrecognized configuration command. (Previously, the sender
received no feedback.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a TIPC application to cancel an existing
topology service subscription by re-requesting the subscription
with the TIPC_SUB_CANCEL filter bit set. (All other bits of
the cancel request must match the original subscription request.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a minor bug that prevents "tipc-config -l" from
displaying the multicast link if a TIPC node has never successfully
established at least one unicast link.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects an issue wherein a previouly failed node could
not reestablish a links to a non-failing node in the TIPC network
until the latter node detected the link failure itself (which might
be configured to take up to 30 seconds). The non-failing node now
responds to link setup requests from a previously failed node in at
most 1 second, allowing it to detect the link failure more quickly.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tivially re-orders the entries in TIPC's list of local
publications so that applications will receive publication events
in the order they were published.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances TIPC's Ethernet support to include VLAN interfaces.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the compiler to optimize out any code that tries to
send debugging output to the null print buffer (TIPC_NULL), a capability
that was unintentionally broken during the recent print buffer rework.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a simple test so TIPC doesn't try waking up processes
waiting on a socket if there are none waiting.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC now rejects and logs link setup requests from node <Z.C.N> if the
receiving node already has a functional link to that node on the associated
interface, or if the requestor is using the same <Z.C.N> as the receiver.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stream socket send code was not initializing some required fields
of the temporary msghdr structure it was utilizing; this is now fixed.
A check has also been added to detect if a user illegally specifies
a destination address when sending on an established stream connection.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change modifies TIPC's print buffer code as follows:
1) Now supports small print buffers (min. size reduced from 512 bytes to 64)
2) Now uses TIPC_NULL print buffer structure to indicate null device
instead of NULL pointer (this simplified error handling)
3) Fixed misuse of console buffer structure by tipc_dump()
4) Added and corrected comments in various places
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the ->fopen callback from lockd into nfsd to find that an
answer cannot be given straight away (an upcall is needed) and so the request
has to be 'dropped', to be retried later. That error status is not currently
propagated back.
So:
Change nlm_fopen to return nlm error codes (rather than a private
protocol) and define a new nlm_drop_reply code.
Cause nlm_drop_reply to cause the rpc request to get rpc_drop_reply
when this error comes back.
Cause svc_process to drop a request which returns a status of
rpc_drop_reply.
[akpm@osdl.org: fix warning storm]
Cc: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make net_random() more widely available by calling it random32
akpm: hopefully this will permit the removal of carta_random32. That needs
confirmation from Stephane - this code looks somewhat more computationally
expensive, and has a different (ie: callee-stateful) interface.
[akpm@osdl.org: lots of build fixes, cleanups]
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a slab corruption in ieee80211softmac_auth(). The size of a buffer
was miscomputed.
see http://bugzilla.kernel.org/show_bug.cgi?id=7245
Acked-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some race conditions in the WirelessExtension
handling and association handling code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bt_proto array needs to be protected by some kind of locking to
prevent a race condition between bt_sock_create and bt_sock_register.
And in addition all calls to sk_alloc need to be made GFP_ATOMIC now.
Signed-off-by: Masatake YAMATO <jet@gyve.org>
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the DLC device is no longer attached to the TTY device, then it
makes no sense to go through with changing the termios settings.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the connection lookup for the device structure fails, the reference
count for the HCI device needs to be decremented.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth HID specification demands that the interrupt channel
shall be disconnected first. This is needed to pass the qualification
tests.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Most Bluetooth chips don't support concurrent connect requests, because
this would involve a multiple baseband page with only one radio. In the
case an upper layer like L2CAP requests a concurrent connect these chips
return the error "Command Disallowed" for the second request. If this
happens it the responsibility of the Bluetooth core to queue the request
and try again after the previous connect attempt has been completed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth subsystem currently uses a platform device for devices
with no parent. It is a better idea to use the new virtual devices
tree for these.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some return values of the driver core register and create functions
are not handled and so might cause unexpected problems.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There exists no attempt do deal with the fact that a structure with
a uint32_t followed by a pointer is going to be different for 32-bit
and 64-bit userspace. Any 32-bit process trying to use it will be
failing with -EFAULT if it's lucky; suffering from having data dumped
at a random address if it's not.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is missing the MODULE_LICENSE statements and taints the kernel
upon loading. License is obvious from the beginning of the file.
Signed-off-by: Jan Dittmer <jdi@l4x.org>
Signed-off-by: Joerg Roedel <joro-lkml@zlug.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes rt6_lookup() to provide the source address in the flow
and sets RT6_LOOKUP_F_HAS_SADDR whenever it is present in
the flow.
Avoids unnecessary prefix comparisons by checking for a prefix
length first.
Fixes the rule logic to not match packets if a source selector
has been specified but no source address is available.
Thanks to Kim Nordlund <kim.nordlund@nokia.com> for working
on this patch with me.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing counter bump when hashing in a new ACQ
xfrm_state.
Now that we have two spots to do the hash grow
check, break it out into a helper function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The CIPSO passthrough mapping had a problem when sending categories which
would cause no or incorrect categories to be sent on the wire with a packet.
This patch fixes the problem which was a simple off-by-one bug.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Fix several places in the CIPSO code where it was dereferencing fields which
did not have valid pointers by moving those pointer dereferences into code
blocks where the pointers are valid.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Flush the forwarding table when carrier is lost. This helps for
availability because we don't want to forward to a downed device and
new packets may come in on other links.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove (compilation-breaking) debugging messages introduced at early
development stage.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONNSECMARK needs conntrack, add missing dependency to fix linking error
with CONNSECMARK=y and CONNTRACK=m.
Reported by Toralf Förster <toralf.foerster@gmx.de>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the tos field is only a single byte large, the values need to
be converted to net-endian for the checkum update so they are in the
corrent byte position. Also fix incorrect endian annotations.
Reported by Stephane Chazelas <Stephane_Chazelas@yahoo.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use rb_first() to get first entry in rb tree.
Signed-off-by: Akinbou Mita <akinobu.mita@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb is the netlink query, nskb is the reply message.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are not necessarily initialized to zero by the compiler,
for example when using run-time initializers of automatic
on-stack variables.
Noticed by Eric Dumazet and Patrick McHardy.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the changes to net/ipv6/addrconf.c to remove sit
specific code if the sit driver is not selected.
Signed-off-by: Joerg Roedel <joro-lkml@zlug.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the driver of the IPv6-in-IPv4 tunnel driver (sit)
from the IPv6 module. It adds an option to Kconfig which makes it
possible to compile it as a seperate module.
Signed-off-by: Joerg Roedel <joro-lkml@zlug.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If more than one file descriptor was sent with an SCM_RIGHTS message,
and on the receiving end, after installing a nonzero (but not all)
file descritpors the process runs out of fds, then the already
installed fds will be lost (userspace will have no way of knowing
about them).
The following patch makes sure, that at least the already installed
fds are sent to userspace. It doesn't solve the issue of losing file
descriptors in case of an EFAULT on the userspace buffer.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Show the true receive buffer usage.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing receiver buffer accounting, we always used skb->truesize.
This is problematic when processing bundled DATA chunks because for
every DATA chunk that could be small part of one large skb, we would
charge the size of the entire skb. The new approach is to store the
size of the DATA chunk we are accounting for in the sctp_ulpevent
structure and use that stored value for accounting.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This treats the security errors encountered in the case of
socket policy matching, the same as how these are treated in
the case of main/sub policies, which is to return a full lookup
failure.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently when an IPSec policy rule doesn't specify a security
context, it is assumed to be "unlabeled" by SELinux, and so
the IPSec policy rule fails to match to a flow that it would
otherwise match to, unless one has explicitly added an SELinux
policy rule allowing the flow to "polmatch" to the "unlabeled"
IPSec policy rules. In the absence of such an explicitly added
SELinux policy rule, the IPSec policy rule fails to match and
so the packet(s) flow in clear text without the otherwise applicable
xfrm(s) applied.
The above SELinux behavior violates the SELinux security notion of
"deny by default" which should actually translate to "encrypt by
default" in the above case.
This was first reported by Evgeniy Polyakov and the way James Morris
was seeing the problem was when connecting via IPsec to a
confined service on an SELinux box (vsftpd), which did not have the
appropriate SELinux policy permissions to send packets via IPsec.
With this patch applied, SELinux "polmatching" of flows Vs. IPSec
policy rules will only come into play when there's a explicit context
specified for the IPSec policy rule (which also means there's corresponding
SELinux policy allowing appropriate domains/flows to polmatch to this context).
Secondly, when a security module is loaded (in this case, SELinux), the
security_xfrm_policy_lookup() hook can return errors other than access denied,
such as -EINVAL. We were not handling that correctly, and in fact
inverting the return logic and propagating a false "ok" back up to
xfrm_lookup(), which then allowed packets to pass as if they were not
associated with an xfrm policy.
The solution for this is to first ensure that errno values are
correctly propagated all the way back up through the various call chains
from security_xfrm_policy_lookup(), and handled correctly.
Then, flow_cache_lookup() is modified, so that if the policy resolver
fails (typically a permission denied via the security module), the flow
cache entry is killed rather than having a null policy assigned (which
indicates that the packet can pass freely). This also forces any future
lookups for the same flow to consult the security module (e.g. SELinux)
for current security policy (rather than, say, caching the error on the
flow cache entry).
This patch: Fix the selinux side of things.
This makes sure SELinux polmatching of flow contexts to IPSec policy
rules comes into play only when an explicit context is associated
with the IPSec policy rule.
Also, this no longer defaults the context of a socket policy to
the context of the socket since the "no explicit context" case
is now handled properly.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
When a security module is loaded (in this case, SELinux), the
security_xfrm_policy_lookup() hook can return an access denied permission
(or other error). We were not handling that correctly, and in fact
inverting the return logic and propagating a false "ok" back up to
xfrm_lookup(), which then allowed packets to pass as if they were not
associated with an xfrm policy.
The way I was seeing the problem was when connecting via IPsec to a
confined service on an SELinux box (vsftpd), which did not have the
appropriate SELinux policy permissions to send packets via IPsec.
The first SYNACK would be blocked, because of an uncached lookup via
flow_cache_lookup(), which would fail to resolve an xfrm policy because
the SELinux policy is checked at that point via the resolver.
However, retransmitted SYNACKs would then find a cached flow entry when
calling into flow_cache_lookup() with a null xfrm policy, which is
interpreted by xfrm_lookup() as the packet not having any associated
policy and similarly to the first case, allowing it to pass without
transformation.
The solution presented here is to first ensure that errno values are
correctly propagated all the way back up through the various call chains
from security_xfrm_policy_lookup(), and handled correctly.
Then, flow_cache_lookup() is modified, so that if the policy resolver
fails (typically a permission denied via the security module), the flow
cache entry is killed rather than having a null policy assigned (which
indicates that the packet can pass freely). This also forces any future
lookups for the same flow to consult the security module (e.g. SELinux)
for current security policy (rather than, say, caching the error on the
flow cache entry).
Signed-off-by: James Morris <jmorris@namei.org>
Testing revealed a problem with the NetLabel cache where a cached entry could
be freed while in use by the LSM layer causing an oops and other problems.
This patch fixes that problem by introducing a reference counter to the cache
entry so that it is only freed when it is no longer in use.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
This annotation makes it possible to assign a subclass on lock init. This
annotation is meant to reduce the _nested() annotations by assigning a
default subclass.
One could do without this annotation and rely on lockdep_set_class()
exclusively, but that would require a manual stack of struct lock_class_key
objects.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is some confusion about the meaning of 'bufsz' for a sunrpc server.
In some cases it is the largest message that can be sent or received. In
other cases it is the largest 'payload' that can be included in a NFS
message.
In either case, it is not possible for both the request and the reply to be
this large. One of the request or reply may only be one page long, which
fits nicely with NFS.
So we remove 'bufsz' and replace it with two numbers: 'max_payload' and
'max_mesg'. Max_payload is the size that the server requests. It is used
by the server to check the max size allowed on a particular connection:
depending on the protocol a lower limit might be used.
max_mesg is the largest single message that can be sent or received. It is
calculated as the max_payload, rounded up to a multiple of PAGE_SIZE, and
with PAGE_SIZE added to overhead. Only one of the request and reply may be
this size. The other must be at most one page.
Cc: Greg Banks <gnb@sgi.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh:
Remove all inclusions of <linux/config.h>
Manually resolved trivial path conflicts due to removed files in
the sound/oss/ subdirectory.
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[XFRM]: BEET mode
[TCP]: Kill warning in tcp_clean_rtx_queue().
[NET_SCHED]: Remove old estimator implementation
[ATM]: [zatm] always *pcr in alloc_shaper()
[ATM]: [ambassador] Change the return type to reflect reality
[ATM]: kmalloc to kzalloc patches for drivers/atm
[TIPC]: fix printk warning
[XFRM]: Clearing xfrm_policy_count[] to zero during flush is incorrect.
[XFRM] STATE: Use destination address for src hash.
[NEIGH]: always use hash_mask under tbl lock
[UDP]: Fix MSG_PROBE crash
[UDP6]: Fix flowi clobbering
[NET_SCHED]: Revert "HTB: fix incorrect use of RB_EMPTY_NODE"
[NETFILTER]: ebt_mark: add or/and/xor action support to mark target
[NETFILTER]: ipt_REJECT: remove largely duplicate route_reverse function
[NETFILTER]: Honour source routing for LVS-NAT
[NETFILTER]: add type parameter to ip_route_me_harder
[NETFILTER]: Kconfig: fix xt_physdev dependencies
The rpc reply has multiple levels of error returns. The code here contributes
to the confusion by using "accept_statp" for a pointer to what the rfc (and
wireshark, etc.) refer to as the "reply_stat". (The confusion is compounded
by the fact that the rfc also has an "accept_stat" which follows the
reply_stat in the succesful case.)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the request is denied after gss_accept was called, we shouldn't try to wrap
the reply. We were checking the accept_stat but not the reply_stat.
To check the reply_stat in _release, we need a pointer to before (rather than
after) the verifier, so modify body_start appropriately.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Factor out some common code from the integrity and privacy cases.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The NFSACL patches introduced support for multiple RPC services listening on
the same transport. However, only the first of these services was registered
with portmapper. This was perfectly fine for nfsacl, as you traditionally do
not want these to show up in a portmapper listing.
The patch below changes the default behavior to always register all services
listening on a given transport, but retains the old behavior for nfsacl
services.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Speed up high call-rate workloads by caching the struct ip_map for the peer on
the connected struct svc_sock instead of looking it up in the ip_map cache
hashtable on every call. This helps workloads using AUTH_SYS authentication
over TCP.
Testing was on a 4 CPU 4 NIC Altix using 4 IRIX clients, each with 16
synthetic client threads simulating an rsync (i.e. recursive directory
listing) workload reading from an i386 RH9 install image (161480 regular files
in 10841 directories) on the server. That tree is small enough to fill in the
server's RAM so no disk traffic was involved. This setup gives a sustained
call rate in excess of 60000 calls/sec before being CPU-bound on the server.
Profiling showed strcmp(), called from ip_map_match(), was taking 4.8% of each
CPU, and ip_map_lookup() was taking 2.9%. This patch drops both contribution
into the profile noise.
Note that the above result overstates this value of this patch for most
workloads. The synthetic clients are all using separate IP addresses, so
there are 64 entries in the ip_map cache hash. Because the kernel measured
contained the bug fixed in commit
commit 1f1e030bf7
and was running on 64bit little-endian machine, probably all of those 64
entries were on a single chain, thus increasing the cost of ip_map_lookup().
With a modern kernel you would need more clients to see the same amount of
performance improvement. This patch has helped to scale knfsd to handle a
deployment with 2000 NFS clients.
Signed-off-by: Greg Banks <gnb@melbourne.sgi.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The limit over UDP remains at 32K. Also, make some of the apparently
arbitrary sizing constants clearer.
The biggest change here involves replacing NFSSVC_MAXBLKSIZE by a function of
the rqstp. This allows it to be different for different protocols (udp/tcp)
and also allows it to depend on the servers declared sv_bufsiz.
Note that we don't actually increase sv_bufsz for nfs yet. That comes next.
Signed-off-by: Greg Banks <gnb@melbourne.sgi.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
.. by allocating the array of 'kvec' in 'struct svc_rqst'.
As we plan to increase RPCSVC_MAXPAGES from 8 upto 256, we can no longer
allocate an array of this size on the stack. So we allocate it in 'struct
svc_rqst'.
However svc_rqst contains (indirectly) an array of the same type and size
(actually several, but they are in a union). So rather than waste space, we
move those arrays out of the separately allocated union and into svc_rqst to
share with the kvec moved out of svc_tcp_recvfrom (various arrays are used at
different times, so there is no conflict).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We are planning to increase RPCSVC_MAXPAGES from about 8 to about 256. This
means we need to be a bit careful about arrays of size RPCSVC_MAXPAGES.
struct svc_rqst contains two such arrays. However the there are never more
that RPCSVC_MAXPAGES pages in the two arrays together, so only one array is
needed.
The two arrays are for the pages holding the request, and the pages holding
the reply. Instead of two arrays, we can simply keep an index into where the
first reply page is.
This patch also removes a number of small inline functions that probably
server to obscure what is going on rather than clarify it, and opencode the
needed functionality.
Also remove the 'rq_restailpage' variable as it is *always* 0. i.e. if the
response 'xdr' structure has a non-empty tail it is always in the same pages
as the head.
check counters are initilised and incr properly
check for consistant usage of ++ etc
maybe extra some inlines for common approach
general review
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Magnus Maatta <novell@kiruna.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arrgg.. We cannot 'lockd_up' before 'svc_addsock' as we don't know the
protocol yet.... So switch it around again and save the name of the created
sockets so that it can be closed if lock_up fails.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The refcount that nfsd holds on lockd is based on the number of open sockets.
So when we close a socket, we should decrement the ref (with lockd_down).
Currently when a socket is closed via writing to the portlist file, that
doesn't happen.
So: make sure we get an error return if the socket that was requested does is
not found, and call lockd_down if it was.
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- rename ____kmalloc to kmalloc_track_caller so that people have a chance
to guess what it does just from it's name. Add a comment describing it
for those who don't. Also move it after kmalloc in slab.h so people get
less confused when they are just looking for kmalloc - move things around
in slab.c a little to reduce the ifdef mess.
[penberg@cs.helsinki.fi: Fix up reversed #ifdef]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the BEET mode (Bound End-to-End Tunnel) with as
specified by the ietf draft at the following link:
http://www.ietf.org/internet-drafts/draft-nikander-esp-beet-mode-06.txt
The patch provides only single family support (i.e. inner family =
outer family).
Signed-off-by: Diego Beltrami <diego.beltrami@gmail.com>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Abhinav Pathak <abhinav.pathak@hiit.fi>
Signed-off-by: Jeff Ahrenholz <ahrenholz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC can't tell we always initialize 'tv' in all the cases
we actually use it, so explicitly set it up with zeros.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused file, estimators live in net/core/gen_estimator.c now.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc spits out this warning:
net/tipc/link.c: In function ‘link_retransmit_failure’:
net/tipc/link.c:1669: warning: cast from pointer to integer of different
size
More than a little bit ugly, storing integers in void*, but at least the
code is correct, unlike some of the more crufty Linux kernel code found
elsewhere.
Rather than having two casts to massage the value into u32, it's easier
just to have a single cast and use "%lu", since it's just a printk.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we flush policies, we do a type match so we might not
actually delete all policies matching a certain direction.
So keep track of how many policies we actually kill and
subtract that number from xfrm_policy_count[dir] at the
end.
Based upon a patch by Masahide NAKAMURA.
Signed-off-by: David S. Miller <davem@davemloft.net>
Src hash is introduced for Mobile IPv6 route optimization usage.
On current kenrel code it is calculated with source address only.
It results we uses the same hash value for outbound state (when
the node has only one address for Mobile IPv6).
This patch use also destination address as peer information for
src hash to be dispersed.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure hash_mask is protected with tbl->lock in all cases just like
the hash_buckets.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP tracks corking status through the pending variable. The
IP layer also tracks it through the socket write queue. It
is possible for the two to get out of sync when MSG_PROBE is
used.
This patch changes UDP to check the write queue to ensure
that the two stay in sync.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The udp6_sendmsg function uses a shared buffer to store the
flow without taking any locks. This leads to races with SMP.
This patch moves the flowi object onto the stack.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
