kernel_optimize_test/arch/ia64/kernel/Makefile
Anil S Keshavamurthy b2761dc262 [PATCH] Kprobes/IA64: architecture specific JProbes support
This patch adds IA64 architecture specific JProbes support on top of Kprobes

Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 09:45:22 -07:00

55 lines
1.9 KiB
Makefile

#
# Makefile for the linux kernel.
#
extra-y := head.o init_task.o vmlinux.lds
obj-y := acpi.o entry.o efi.o efi_stub.o gate-data.o fsys.o ia64_ksyms.o irq.o irq_ia64.o \
irq_lsapic.o ivt.o machvec.o pal.o patch.o process.o perfmon.o ptrace.o sal.o \
salinfo.o semaphore.o setup.o signal.o sys_ia64.o time.o traps.o unaligned.o \
unwind.o mca.o mca_asm.o topology.o
obj-$(CONFIG_IA64_BRL_EMU) += brl_emu.o
obj-$(CONFIG_IA64_GENERIC) += acpi-ext.o
obj-$(CONFIG_IA64_HP_ZX1) += acpi-ext.o
obj-$(CONFIG_IA64_HP_ZX1_SWIOTLB) += acpi-ext.o
obj-$(CONFIG_IA64_PALINFO) += palinfo.o
obj-$(CONFIG_IOSAPIC) += iosapic.o
obj-$(CONFIG_MODULES) += module.o
obj-$(CONFIG_SMP) += smp.o smpboot.o domain.o
obj-$(CONFIG_PERFMON) += perfmon_default_smpl.o
obj-$(CONFIG_IA64_CYCLONE) += cyclone.o
obj-$(CONFIG_IA64_MCA_RECOVERY) += mca_recovery.o
obj-$(CONFIG_KPROBES) += kprobes.o jprobes.o
obj-$(CONFIG_IA64_UNCACHED_ALLOCATOR) += uncached.o
mca_recovery-y += mca_drv.o mca_drv_asm.o
# The gate DSO image is built using a special linker script.
targets += gate.so gate-syms.o
extra-y += gate.so gate-syms.o gate.lds gate.o
# fp_emulate() expects f2-f5,f16-f31 to contain the user-level state.
CFLAGS_traps.o += -mfixed-range=f2-f5,f16-f31
CPPFLAGS_gate.lds := -P -C -U$(ARCH)
quiet_cmd_gate = GATE $@
cmd_gate = $(CC) -nostdlib $(GATECFLAGS_$(@F)) -Wl,-T,$(filter-out FORCE,$^) -o $@
GATECFLAGS_gate.so = -shared -s -Wl,-soname=linux-gate.so.1
$(obj)/gate.so: $(obj)/gate.lds $(obj)/gate.o FORCE
$(call if_changed,gate)
$(obj)/built-in.o: $(obj)/gate-syms.o
$(obj)/built-in.o: ld_flags += -R $(obj)/gate-syms.o
GATECFLAGS_gate-syms.o = -r
$(obj)/gate-syms.o: $(obj)/gate.lds $(obj)/gate.o FORCE
$(call if_changed,gate)
# gate-data.o contains the gate DSO image as data in section .data.gate.
# We must build gate.so before we can assemble it.
# Note: kbuild does not track this dependency due to usage of .incbin
$(obj)/gate-data.o: $(obj)/gate.so