forked from luck/tmp_suning_uos_patched
220995622d
We want to enable kgdb to debug the early parts of the kernel. Unfortunately kgdb normally is a client of the tty API in the kernel and serial drivers don't register to the tty layer until fairly late in the boot process. Serial drivers do, however, commonly register a boot console. Let's enable the kgdboc driver to work with boot consoles to provide early debugging. This change co-opts the existing read() function pointer that's part of "struct console". It's assumed that if a boot console (with the flag CON_BOOT) has implemented read() that both the read() and write() function are polling functions. That means they work without interrupts and read() will return immediately (with 0 bytes read) if there's nothing to read. This should be a safe assumption since it appears that no current boot consoles implement read() right now and there seems no reason to do so unless they wanted to support "kgdboc_earlycon". The normal/expected way to make all this work is to use "kgdboc_earlycon" and "kgdboc" together. You should point them both to the same physical serial connection. At boot time, as the system transitions from the boot console to the normal console (and registers a tty), kgdb will switch over. One awkward part of all this, though, is that there can be a window where the boot console goes away and we can't quite transtion over to the main kgdboc that uses the tty layer. There are two main problems: 1. The act of registering the tty doesn't cause any call into kgdboc so there is a window of time when the tty is there but kgdboc's init code hasn't been called so we can't transition to it. 2. On some serial drivers the normal console inits (and replaces the boot console) quite early in the system. Presumably these drivers were coded up before earlycon worked as well as it does today and probably they don't need to do this anymore, but it causes us problems nontheless. Problem #1 is not too big of a deal somewhat due to the luck of probe ordering. kgdboc is last in the tty/serial/Makefile so its probe gets right after all other tty devices. It's not fun to rely on this, but it does work for the most part. Problem #2 is a big deal, but only for some serial drivers. Other serial drivers end up registering the console (which gets rid of the boot console) and tty at nearly the same time. The way we'll deal with the window when the system has stopped using the boot console and the time when we're setup using the tty is to keep using the boot console. This may sound surprising, but it has been found to work well in practice. If it doesn't work, it shouldn't be too hard for a given serial driver to make it keep working. Specifically, it's expected that the read()/write() function provided in the boot console should be the same (or nearly the same) as the normal kgdb polling functions. That means continuing to use them should work just fine. To make things even more likely to work work we'll also trap the recently added exit() function in the boot console we're using and delay any calls to it until we're all done with the boot console. NOTE: there could be ways to use all this in weird / unexpected ways. If you do something like this, it's a bit of a buyer beware situation. Specifically: - If you specify only "kgdboc_earlycon" but not "kgdboc" then (depending on your serial driver) things will probably work OK, but you'll get a warning printed the first time you use kgdb after the boot console is gone. You'd only be able to do this, of course, if the serial driver you're running atop provided an early boot console. - If your "kgdboc_earlycon" and "kgdboc" devices are not the same device things should work OK, but it'll be your job to switch over which device you're monitoring (including figuring out how to switch over gdb in-flight if you're using it). When trying to enable "kgdboc_earlycon" it should be noted that the names that are registered through the boot console layer and the tty layer are not the same for the same port. For example when debugging on one board I'd need to pass "kgdboc_earlycon=qcom_geni kgdboc=ttyMSM0" to enable things properly. Since digging up the boot console name is a pain and there will rarely be more than one boot console enabled, you can provide the "kgdboc_earlycon" parameter without specifying the name of the boot console. In this case we'll just pick the first boot that implements read() that we find. This new "kgdboc_earlycon" parameter should be contrasted to the existing "ekgdboc" parameter. While both provide a way to debug very early, the usage and mechanisms are quite different. Specifically "kgdboc_earlycon" is meant to be used in tandem with "kgdboc" and there is a transition from one to the other. The "ekgdboc" parameter, on the other hand, replaces the "kgdboc" parameter. It runs the same logic as the "kgdboc" parameter but just relies on your TTY driver being present super early. The only known usage of the old "ekgdboc" parameter is documented as "ekgdboc=kbd earlyprintk=vga". It should be noted that "kbd" has special treatment allowing it to init early as a tty device. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Sumit Garg <sumit.garg@linaro.org> Link: https://lore.kernel.org/r/20200507130644.v4.8.I8fba5961bf452ab92350654aa61957f23ecf0100@changeid Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> |
||
|---|---|---|
| .. | ||
| kdb | ||
| debug_core.c | ||
| debug_core.h | ||
| gdbstub.c | ||
| Makefile | ||