kernel_optimize_test/drivers/net/phy/bcm7xxx.c
Florian Fainelli b08d46b01e net: phy: bcm7xxx: Add BCM74371 PHY ID
Add the BCM74371 PHY ID to the list of supported chips. This is a 28nm
technology Gigabit PHY SoC.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-07 13:03:10 -05:00

490 lines
13 KiB
C

/*
* Broadcom BCM7xxx internal transceivers support.
*
* Copyright (C) 2014, Broadcom Corporation
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
#include <linux/module.h>
#include <linux/phy.h>
#include <linux/delay.h>
#include "bcm-phy-lib.h"
#include <linux/bitops.h>
#include <linux/brcmphy.h>
#include <linux/mdio.h>
/* Broadcom BCM7xxx internal PHY registers */
/* 40nm only register definitions */
#define MII_BCM7XXX_100TX_AUX_CTL 0x10
#define MII_BCM7XXX_100TX_FALSE_CAR 0x13
#define MII_BCM7XXX_100TX_DISC 0x14
#define MII_BCM7XXX_AUX_MODE 0x1d
#define MII_BCM7XXX_64CLK_MDIO BIT(12)
#define MII_BCM7XXX_TEST 0x1f
#define MII_BCM7XXX_SHD_MODE_2 BIT(2)
/* 28nm only register definitions */
#define MISC_ADDR(base, channel) base, channel
#define DSP_TAP10 MISC_ADDR(0x0a, 0)
#define PLL_PLLCTRL_1 MISC_ADDR(0x32, 1)
#define PLL_PLLCTRL_2 MISC_ADDR(0x32, 2)
#define PLL_PLLCTRL_4 MISC_ADDR(0x33, 0)
#define AFE_RXCONFIG_0 MISC_ADDR(0x38, 0)
#define AFE_RXCONFIG_1 MISC_ADDR(0x38, 1)
#define AFE_RXCONFIG_2 MISC_ADDR(0x38, 2)
#define AFE_RX_LP_COUNTER MISC_ADDR(0x38, 3)
#define AFE_TX_CONFIG MISC_ADDR(0x39, 0)
#define AFE_VDCA_ICTRL_0 MISC_ADDR(0x39, 1)
#define AFE_VDAC_OTHERS_0 MISC_ADDR(0x39, 3)
#define AFE_HPF_TRIM_OTHERS MISC_ADDR(0x3a, 0)
struct bcm7xxx_phy_priv {
u64 *stats;
};
static void r_rc_cal_reset(struct phy_device *phydev)
{
/* Reset R_CAL/RC_CAL Engine */
bcm_phy_write_exp(phydev, 0x00b0, 0x0010);
/* Disable Reset R_AL/RC_CAL Engine */
bcm_phy_write_exp(phydev, 0x00b0, 0x0000);
}
static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev)
{
/* Increase VCO range to prevent unlocking problem of PLL at low
* temp
*/
bcm_phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048);
/* Change Ki to 011 */
bcm_phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b);
/* Disable loading of TVCO buffer to bandgap, set bandgap trim
* to 111
*/
bcm_phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20);
/* Adjust bias current trim by -3 */
bcm_phy_write_misc(phydev, DSP_TAP10, 0x690b);
/* Switch to CORE_BASE1E */
phy_write(phydev, MII_BRCM_CORE_BASE1E, 0xd);
r_rc_cal_reset(phydev);
/* write AFE_RXCONFIG_0 */
bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19);
/* write AFE_RXCONFIG_1 */
bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f);
/* write AFE_RX_LP_COUNTER */
bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
/* write AFE_HPF_TRIM_OTHERS */
bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b);
/* write AFTE_TX_CONFIG */
bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800);
return 0;
}
static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
{
/* AFE_RXCONFIG_0 */
bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);
/* AFE_RXCONFIG_1 */
bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
/* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */
bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);
/* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */
bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
/* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */
bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);
/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
/* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */
bcm_phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);
/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
* offset for HT=0 code
*/
bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010);
/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);
/* Reset R_CAL/RC_CAL engine */
r_rc_cal_reset(phydev);
return 0;
}
static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev)
{
/* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */
bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
/* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */
bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);
/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
* offset for HT=0 code
*/
bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010);
/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);
/* Reset R_CAL/RC_CAL engine */
r_rc_cal_reset(phydev);
return 0;
}
static int bcm7xxx_28nm_a0_patch_afe_config_init(struct phy_device *phydev)
{
/* +1 RC_CAL codes for RL centering for both LT and HT conditions */
bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0xd003);
/* Cut master bias current by 2% to compensate for RC_CAL offset */
bcm_phy_write_misc(phydev, DSP_TAP10, 0x791b);
/* Improve hybrid leakage */
bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x10e3);
/* Change rx_on_tune 8 to 0xf */
bcm_phy_write_misc(phydev, 0x21, 0x2, 0x87f6);
/* Change 100Tx EEE bandwidth */
bcm_phy_write_misc(phydev, 0x22, 0x2, 0x017d);
/* Enable ffe zero detection for Vitesse interoperability */
bcm_phy_write_misc(phydev, 0x26, 0x2, 0x0015);
r_rc_cal_reset(phydev);
return 0;
}
static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
{
u8 rev = PHY_BRCM_7XXX_REV(phydev->dev_flags);
u8 patch = PHY_BRCM_7XXX_PATCH(phydev->dev_flags);
u8 count;
int ret = 0;
/* Newer devices have moved the revision information back into a
* standard location in MII_PHYS_ID[23]
*/
if (rev == 0)
rev = phydev->phy_id & ~phydev->drv->phy_id_mask;
pr_info_once("%s: %s PHY revision: 0x%02x, patch: %d\n",
phydev_name(phydev), phydev->drv->name, rev, patch);
/* Dummy read to a register to workaround an issue upon reset where the
* internal inverter may not allow the first MDIO transaction to pass
* the MDIO management controller and make us return 0xffff for such
* reads.
*/
phy_read(phydev, MII_BMSR);
switch (rev) {
case 0xb0:
ret = bcm7xxx_28nm_b0_afe_config_init(phydev);
break;
case 0xd0:
ret = bcm7xxx_28nm_d0_afe_config_init(phydev);
break;
case 0xe0:
case 0xf0:
/* Rev G0 introduces a roll over */
case 0x10:
ret = bcm7xxx_28nm_e0_plus_afe_config_init(phydev);
break;
case 0x01:
ret = bcm7xxx_28nm_a0_patch_afe_config_init(phydev);
break;
default:
break;
}
if (ret)
return ret;
ret = bcm_phy_downshift_get(phydev, &count);
if (ret)
return ret;
/* Only enable EEE if Wirespeed/downshift is disabled */
ret = bcm_phy_set_eee(phydev, count == DOWNSHIFT_DEV_DISABLE);
if (ret)
return ret;
return bcm_phy_enable_apd(phydev, true);
}
static int bcm7xxx_28nm_resume(struct phy_device *phydev)
{
int ret;
/* Re-apply workarounds coming out suspend/resume */
ret = bcm7xxx_28nm_config_init(phydev);
if (ret)
return ret;
/* 28nm Gigabit PHYs come out of reset without any half-duplex
* or "hub" compliant advertised mode, fix that. This does not
* cause any problems with the PHY library since genphy_config_aneg()
* gracefully handles auto-negotiated and forced modes.
*/
return genphy_config_aneg(phydev);
}
static int phy_set_clr_bits(struct phy_device *dev, int location,
int set_mask, int clr_mask)
{
int v, ret;
v = phy_read(dev, location);
if (v < 0)
return v;
v &= ~clr_mask;
v |= set_mask;
ret = phy_write(dev, location, v);
if (ret < 0)
return ret;
return v;
}
static int bcm7xxx_config_init(struct phy_device *phydev)
{
int ret;
/* Enable 64 clock MDIO */
phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XXX_64CLK_MDIO);
phy_read(phydev, MII_BCM7XXX_AUX_MODE);
/* set shadow mode 2 */
ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2);
if (ret < 0)
return ret;
/* set iddq_clkbias */
phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00);
udelay(10);
/* reset iddq_clkbias */
phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00);
phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555);
/* reset shadow mode 2 */
ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0, MII_BCM7XXX_SHD_MODE_2);
if (ret < 0)
return ret;
return 0;
}
/* Workaround for putting the PHY in IDDQ mode, required
* for all BCM7XXX 40nm and 65nm PHYs
*/
static int bcm7xxx_suspend(struct phy_device *phydev)
{
int ret;
const struct bcm7xxx_regs {
int reg;
u16 value;
} bcm7xxx_suspend_cfg[] = {
{ MII_BCM7XXX_TEST, 0x008b },
{ MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 },
{ MII_BCM7XXX_100TX_DISC, 0x7000 },
{ MII_BCM7XXX_TEST, 0x000f },
{ MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 },
{ MII_BCM7XXX_TEST, 0x000b },
};
unsigned int i;
for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) {
ret = phy_write(phydev,
bcm7xxx_suspend_cfg[i].reg,
bcm7xxx_suspend_cfg[i].value);
if (ret)
return ret;
}
return 0;
}
static int bcm7xxx_28nm_get_tunable(struct phy_device *phydev,
struct ethtool_tunable *tuna,
void *data)
{
switch (tuna->id) {
case ETHTOOL_PHY_DOWNSHIFT:
return bcm_phy_downshift_get(phydev, (u8 *)data);
default:
return -EOPNOTSUPP;
}
}
static int bcm7xxx_28nm_set_tunable(struct phy_device *phydev,
struct ethtool_tunable *tuna,
const void *data)
{
u8 count = *(u8 *)data;
int ret;
switch (tuna->id) {
case ETHTOOL_PHY_DOWNSHIFT:
ret = bcm_phy_downshift_set(phydev, count);
break;
default:
return -EOPNOTSUPP;
}
if (ret)
return ret;
/* Disable EEE advertisment since this prevents the PHY
* from successfully linking up, trigger auto-negotiation restart
* to let the MAC decide what to do.
*/
ret = bcm_phy_set_eee(phydev, count == DOWNSHIFT_DEV_DISABLE);
if (ret)
return ret;
return genphy_restart_aneg(phydev);
}
static void bcm7xxx_28nm_get_phy_stats(struct phy_device *phydev,
struct ethtool_stats *stats, u64 *data)
{
struct bcm7xxx_phy_priv *priv = phydev->priv;
bcm_phy_get_stats(phydev, priv->stats, stats, data);
}
static int bcm7xxx_28nm_probe(struct phy_device *phydev)
{
struct bcm7xxx_phy_priv *priv;
priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
phydev->priv = priv;
priv->stats = devm_kcalloc(&phydev->mdio.dev,
bcm_phy_get_sset_count(phydev), sizeof(u64),
GFP_KERNEL);
if (!priv->stats)
return -ENOMEM;
return 0;
}
#define BCM7XXX_28NM_GPHY(_oui, _name) \
{ \
.phy_id = (_oui), \
.phy_id_mask = 0xfffffff0, \
.name = _name, \
.features = PHY_GBIT_FEATURES, \
.flags = PHY_IS_INTERNAL, \
.config_init = bcm7xxx_28nm_config_init, \
.config_aneg = genphy_config_aneg, \
.read_status = genphy_read_status, \
.resume = bcm7xxx_28nm_resume, \
.get_tunable = bcm7xxx_28nm_get_tunable, \
.set_tunable = bcm7xxx_28nm_set_tunable, \
.get_sset_count = bcm_phy_get_sset_count, \
.get_strings = bcm_phy_get_strings, \
.get_stats = bcm7xxx_28nm_get_phy_stats, \
.probe = bcm7xxx_28nm_probe, \
}
#define BCM7XXX_40NM_EPHY(_oui, _name) \
{ \
.phy_id = (_oui), \
.phy_id_mask = 0xfffffff0, \
.name = _name, \
.features = PHY_BASIC_FEATURES, \
.flags = PHY_IS_INTERNAL, \
.config_init = bcm7xxx_config_init, \
.config_aneg = genphy_config_aneg, \
.read_status = genphy_read_status, \
.suspend = bcm7xxx_suspend, \
.resume = bcm7xxx_config_init, \
}
static struct phy_driver bcm7xxx_driver[] = {
BCM7XXX_28NM_GPHY(PHY_ID_BCM7250, "Broadcom BCM7250"),
BCM7XXX_28NM_GPHY(PHY_ID_BCM7278, "Broadcom BCM7278"),
BCM7XXX_28NM_GPHY(PHY_ID_BCM7364, "Broadcom BCM7364"),
BCM7XXX_28NM_GPHY(PHY_ID_BCM7366, "Broadcom BCM7366"),
BCM7XXX_28NM_GPHY(PHY_ID_BCM74371, "Broadcom BCM74371"),
BCM7XXX_28NM_GPHY(PHY_ID_BCM7439, "Broadcom BCM7439"),
BCM7XXX_28NM_GPHY(PHY_ID_BCM7439_2, "Broadcom BCM7439 (2)"),
BCM7XXX_28NM_GPHY(PHY_ID_BCM7445, "Broadcom BCM7445"),
BCM7XXX_40NM_EPHY(PHY_ID_BCM7346, "Broadcom BCM7346"),
BCM7XXX_40NM_EPHY(PHY_ID_BCM7362, "Broadcom BCM7362"),
BCM7XXX_40NM_EPHY(PHY_ID_BCM7425, "Broadcom BCM7425"),
BCM7XXX_40NM_EPHY(PHY_ID_BCM7429, "Broadcom BCM7429"),
BCM7XXX_40NM_EPHY(PHY_ID_BCM7435, "Broadcom BCM7435"),
};
static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
{ PHY_ID_BCM7250, 0xfffffff0, },
{ PHY_ID_BCM7278, 0xfffffff0, },
{ PHY_ID_BCM7364, 0xfffffff0, },
{ PHY_ID_BCM7366, 0xfffffff0, },
{ PHY_ID_BCM7346, 0xfffffff0, },
{ PHY_ID_BCM7362, 0xfffffff0, },
{ PHY_ID_BCM7425, 0xfffffff0, },
{ PHY_ID_BCM7429, 0xfffffff0, },
{ PHY_ID_BCM74371, 0xfffffff0, },
{ PHY_ID_BCM7439, 0xfffffff0, },
{ PHY_ID_BCM7435, 0xfffffff0, },
{ PHY_ID_BCM7445, 0xfffffff0, },
{ }
};
module_phy_driver(bcm7xxx_driver);
MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl);
MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver");
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Broadcom Corporation");