kernel_optimize_test/drivers/spi/Makefile
David Brownell d29389de0b spi_gpio driver
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data.  Such SPI masters support:

 - any number of bus instances (bus_num is the platform_device.id)
 - any number of chipselects (one GPIO per spi_device)
 - all four SPI_MODE values, and SPI_CS_HIGH
 - i/o word sizes from 1 to 32 bits;
 - devices configured as with any other spi_master controller

When configured using platform_data, this provides relatively low clock
rates.  On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)

Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.

[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Magnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06 15:59:19 -08:00

46 lines
1.4 KiB
Makefile

#
# Makefile for kernel SPI drivers.
#
ifeq ($(CONFIG_SPI_DEBUG),y)
EXTRA_CFLAGS += -DDEBUG
endif
# small core, mostly translating board-specific
# config declarations into driver model code
obj-$(CONFIG_SPI_MASTER) += spi.o
# SPI master controller drivers (bus)
obj-$(CONFIG_SPI_ATMEL) += atmel_spi.o
obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o
obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
obj-$(CONFIG_SPI_AU1550) += au1550_spi.o
obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
obj-$(CONFIG_SPI_GPIO) += spi_gpio.o
obj-$(CONFIG_SPI_IMX) += spi_imx.o
obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o
obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o
obj-$(CONFIG_SPI_OMAP_UWIRE) += omap_uwire.o
obj-$(CONFIG_SPI_OMAP24XX) += omap2_mcspi.o
obj-$(CONFIG_SPI_ORION) += orion_spi.o
obj-$(CONFIG_SPI_MPC52xx_PSC) += mpc52xx_psc_spi.o
obj-$(CONFIG_SPI_MPC83xx) += spi_mpc83xx.o
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx.o
obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o
obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o
# ... add above this line ...
# SPI protocol drivers (device/link on bus)
obj-$(CONFIG_SPI_AT25) += at25.o
obj-$(CONFIG_SPI_SPIDEV) += spidev.o
obj-$(CONFIG_SPI_TLE62X0) += tle62x0.o
# ... add above this line ...
# SPI slave controller drivers (upstream link)
# ... add above this line ...
# SPI slave drivers (protocol for that link)
# ... add above this line ...