AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity
6a06fa6863
kernel_optimize_test/arch/arm/mach-omap2/board-omap3evm.c
Sriram 562138a448 omap3evm: MIgrate to smsc911x ethernet driver 
Migrate to smsc911x ethernet driver instead of smc911x driver.
The smsc911x ethernet driver supports NAPI and performs better
under heavy traffic. With the smc911x driver we were witnessing
very high iowait time for high IO load over NFS.

Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-22 10:24:33 -08:00

485 lines
12 KiB
C
Raw Blame History

/*
* linux/arch/arm/mach-omap2/board-omap3evm.c
*
* Copyright (C) 2008 Texas Instruments
*
* Modified from mach-omap2/board-3430sdp.c
*
* Initial code: Syed Mohammed Khasim
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/input/matrix_keypad.h>
#include <linux/leds.h>
#include <linux/interrupt.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/i2c/twl4030.h>
#include <linux/usb/otg.h>
#include <linux/smsc911x.h>
#include <linux/regulator/machine.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <plat/board.h>
#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/common.h>
#include <plat/mcspi.h>
#include "sdram-micron-mt46h32m32lf-6.h"
#include "mmc-twl4030.h"
#define OMAP3_EVM_TS_GPIO 175
#define OMAP3_EVM_EHCI_VBUS 22
#define OMAP3_EVM_EHCI_SELECT 61
#define OMAP3EVM_ETHR_START 0x2c000000
#define OMAP3EVM_ETHR_SIZE 1024
#define OMAP3EVM_ETHR_ID_REV 0x50
#define OMAP3EVM_ETHR_GPIO_IRQ 176
#define OMAP3EVM_SMSC911X_CS 5
static u8 omap3_evm_version;
u8 get_omap3_evm_rev(void)
{
return omap3_evm_version;
}
EXPORT_SYMBOL(get_omap3_evm_rev);
static void __init omap3_evm_get_revision(void)
{
void __iomem *ioaddr;
unsigned int smsc_id;
/* Ethernet PHY ID is stored at ID_REV register */
ioaddr = ioremap_nocache(OMAP3EVM_ETHR_START, SZ_1K);
if (!ioaddr)
return;
smsc_id = readl(ioaddr + OMAP3EVM_ETHR_ID_REV) & 0xFFFF0000;
iounmap(ioaddr);
switch (smsc_id) {
/*SMSC9115 chipset*/
case 0x01150000:
omap3_evm_version = OMAP3EVM_BOARD_GEN_1;
break;
/*SMSC 9220 chipset*/
case 0x92200000:
default:
omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
}
}
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
static struct resource omap3evm_smsc911x_resources[] = {
[0] = {
.start = OMAP3EVM_ETHR_START,
.end = (OMAP3EVM_ETHR_START + OMAP3EVM_ETHR_SIZE - 1),
.flags = IORESOURCE_MEM,
},
[1] = {
.start = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ),
.end = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ),
.flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW),
},
};
static struct smsc911x_platform_config smsc911x_config = {
.phy_interface = PHY_INTERFACE_MODE_MII,
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
.flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
};
static struct platform_device omap3evm_smsc911x_device = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(omap3evm_smsc911x_resources),
.resource = &omap3evm_smsc911x_resources[0],
.dev = {
.platform_data = &smsc911x_config,
},
};
static inline void __init omap3evm_init_smsc911x(void)
{
int eth_cs;
struct clk *l3ck;
unsigned int rate;
eth_cs = OMAP3EVM_SMSC911X_CS;
l3ck = clk_get(NULL, "l3_ck");
if (IS_ERR(l3ck))
rate = 100000000;
else
rate = clk_get_rate(l3ck);
if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
OMAP3EVM_ETHR_GPIO_IRQ);
return;
}
gpio_direction_input(OMAP3EVM_ETHR_GPIO_IRQ);
platform_device_register(&omap3evm_smsc911x_device);
}
#else
static inline void __init omap3evm_init_smsc911x(void) { return; }
#endif
static struct regulator_consumer_supply omap3evm_vmmc1_supply = {
.supply = "vmmc",
};
static struct regulator_consumer_supply omap3evm_vsim_supply = {
.supply = "vmmc_aux",
};
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data omap3evm_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
.consumer_supplies = &omap3evm_vmmc1_supply,
};
/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
static struct regulator_init_data omap3evm_vsim = {
.constraints = {
.min_uV = 1800000,
.max_uV = 3000000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
.consumer_supplies = &omap3evm_vsim_supply,
};
static struct twl4030_hsmmc_info mmc[] = {
{
.mmc = 1,
.wires = 4,
.gpio_cd = -EINVAL,
.gpio_wp = 63,
},
{} /* Terminator */
};
static struct gpio_led gpio_leds[] = {
{
.name = "omap3evm::ledb",
/* normally not visible (board underside) */
.default_trigger = "default-on",
.gpio = -EINVAL, /* gets replaced */
.active_low = true,
},
};
static struct gpio_led_platform_data gpio_led_info = {
.leds = gpio_leds,
.num_leds = ARRAY_SIZE(gpio_leds),
};
static struct platform_device leds_gpio = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &gpio_led_info,
},
};
static int omap3evm_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
omap_cfg_reg(L8_34XX_GPIO63);
mmc[0].gpio_cd = gpio + 0;
twl4030_mmc_init(mmc);
/* link regulators to MMC adapters */
omap3evm_vmmc1_supply.dev = mmc[0].dev;
omap3evm_vsim_supply.dev = mmc[0].dev;
/*
* Most GPIOs are for USB OTG. Some are mostly sent to
* the P2 connector; notably LEDA for the LCD backlight.
*/
/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
platform_device_register(&leds_gpio);
return 0;
}
static struct twl4030_gpio_platform_data omap3evm_gpio_data = {
.gpio_base = OMAP_MAX_GPIO_LINES,
.irq_base = TWL4030_GPIO_IRQ_BASE,
.irq_end = TWL4030_GPIO_IRQ_END,
.use_leds = true,
.setup = omap3evm_twl_gpio_setup,
};
static struct twl4030_usb_data omap3evm_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
static int board_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
KEY(0, 2, KEY_A),
KEY(0, 3, KEY_B),
KEY(1, 0, KEY_DOWN),
KEY(1, 1, KEY_UP),
KEY(1, 2, KEY_E),
KEY(1, 3, KEY_F),
KEY(2, 0, KEY_ENTER),
KEY(2, 1, KEY_I),
KEY(2, 2, KEY_J),
KEY(2, 3, KEY_K),
KEY(3, 0, KEY_M),
KEY(3, 1, KEY_N),
KEY(3, 2, KEY_O),
KEY(3, 3, KEY_P)
};
static struct matrix_keymap_data board_map_data = {
.keymap = board_keymap,
.keymap_size = ARRAY_SIZE(board_keymap),
};
static struct twl4030_keypad_data omap3evm_kp_data = {
.keymap_data = &board_map_data,
.rows = 4,
.cols = 4,
.rep = 1,
};
static struct twl4030_madc_platform_data omap3evm_madc_data = {
.irq_line = 1,
};
static struct twl4030_codec_audio_data omap3evm_audio_data = {
.audio_mclk = 26000000,
};
static struct twl4030_codec_data omap3evm_codec_data = {
.audio_mclk = 26000000,
.audio = &omap3evm_audio_data,
};
static struct twl4030_platform_data omap3evm_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
/* platform_data for children goes here */
.keypad = &omap3evm_kp_data,
.madc = &omap3evm_madc_data,
.usb = &omap3evm_usb_data,
.gpio = &omap3evm_gpio_data,
.codec = &omap3evm_codec_data,
};
static struct i2c_board_info __initdata omap3evm_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &omap3evm_twldata,
},
};
static int __init omap3_evm_i2c_init(void)
{
/*
* REVISIT: These entries can be set in omap3evm_twl_data
* after a merge with MFD tree
*/
omap3evm_twldata.vmmc1 = &omap3evm_vmmc1;
omap3evm_twldata.vsim = &omap3evm_vsim;
omap_register_i2c_bus(1, 2600, omap3evm_i2c_boardinfo,
ARRAY_SIZE(omap3evm_i2c_boardinfo));
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
static struct platform_device omap3_evm_lcd_device = {
.name = "omap3evm_lcd",
.id = -1,
};
static struct omap_lcd_config omap3_evm_lcd_config __initdata = {
.ctrl_name = "internal",
};
static void ads7846_dev_init(void)
{
if (gpio_request(OMAP3_EVM_TS_GPIO, "ADS7846 pendown") < 0)
printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
gpio_direction_input(OMAP3_EVM_TS_GPIO);
omap_set_gpio_debounce(OMAP3_EVM_TS_GPIO, 1);
omap_set_gpio_debounce_time(OMAP3_EVM_TS_GPIO, 0xa);
}
static int ads7846_get_pendown_state(void)
{
return !gpio_get_value(OMAP3_EVM_TS_GPIO);
}
struct ads7846_platform_data ads7846_config = {
.x_max = 0x0fff,
.y_max = 0x0fff,
.x_plate_ohms = 180,
.pressure_max = 255,
.debounce_max = 10,
.debounce_tol = 3,
.debounce_rep = 1,
.get_pendown_state = ads7846_get_pendown_state,
.keep_vref_on = 1,
.settle_delay_usecs = 150,
};
static struct omap2_mcspi_device_config ads7846_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1, /* 0: slave, 1: master */
};
struct spi_board_info omap3evm_spi_board_info[] = {
[0] = {
.modalias = "ads7846",
.bus_num = 1,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &ads7846_mcspi_config,
.irq = OMAP_GPIO_IRQ(OMAP3_EVM_TS_GPIO),
.platform_data = &ads7846_config,
},
};
static struct omap_board_config_kernel omap3_evm_config[] __initdata = {
{ OMAP_TAG_LCD, &omap3_evm_lcd_config },
};
static void __init omap3_evm_init_irq(void)
{
omap_board_config = omap3_evm_config;
omap_board_config_size = ARRAY_SIZE(omap3_evm_config);
omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL);
omap_init_irq();
omap_gpio_init();
}
static struct platform_device *omap3_evm_devices[] __initdata = {
&omap3_evm_lcd_device,
};
static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
.port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
.phy_reset = true,
/* PHY reset GPIO will be runtime programmed based on EVM version */
.reset_gpio_port[0] = -EINVAL,
.reset_gpio_port[1] = -EINVAL,
.reset_gpio_port[2] = -EINVAL
};
static void __init omap3_evm_init(void)
{
omap3_evm_get_revision();
omap3_evm_i2c_init();
platform_add_devices(omap3_evm_devices, ARRAY_SIZE(omap3_evm_devices));
spi_register_board_info(omap3evm_spi_board_info,
ARRAY_SIZE(omap3evm_spi_board_info));
omap_serial_init();
#ifdef CONFIG_NOP_USB_XCEIV
/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
usb_nop_xceiv_register();
#endif
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
/* enable EHCI VBUS using GPIO22 */
omap_cfg_reg(AF9_34XX_GPIO22);
gpio_request(OMAP3_EVM_EHCI_VBUS, "enable EHCI VBUS");
gpio_direction_output(OMAP3_EVM_EHCI_VBUS, 0);
gpio_set_value(OMAP3_EVM_EHCI_VBUS, 1);
/* Select EHCI port on main board */
omap_cfg_reg(U3_34XX_GPIO61);
gpio_request(OMAP3_EVM_EHCI_SELECT, "select EHCI port");
gpio_direction_output(OMAP3_EVM_EHCI_SELECT, 0);
gpio_set_value(OMAP3_EVM_EHCI_SELECT, 0);
/* setup EHCI phy reset config */
omap_cfg_reg(AH14_34XX_GPIO21);
ehci_pdata.reset_gpio_port[1] = 21;
} else {
/* setup EHCI phy reset on MDC */
omap_cfg_reg(AF4_34XX_GPIO135_OUT);
ehci_pdata.reset_gpio_port[1] = 135;
}
usb_musb_init();
usb_ehci_init(&ehci_pdata);
ads7846_dev_init();
omap3evm_init_smsc911x();
}
static void __init omap3_evm_map_io(void)
{
omap2_set_globals_343x();
omap2_map_common_io();
}
MACHINE_START(OMAP3EVM, "OMAP3 EVM")
/* Maintainer: Syed Mohammed Khasim - Texas Instruments */
.phys_io = 0x48000000,
.io_pg_offst = ((0xfa000000) >> 18) & 0xfffc,
.boot_params = 0x80000100,
.map_io = omap3_evm_map_io,
.init_irq = omap3_evm_init_irq,
.init_machine = omap3_evm_init,
.timer = &omap_timer,
MACHINE_END
View Git Blame Copy Permalink