forked from luck/tmp_suning_uos_patched
778dbcc1eb
Remove the ARM dependency from the generic "onenand" platform device driver. This change makes the driver useful for other architectures as well. Needed for the SuperH kfr2r09 board. Apart from the obvious Kconfig bits, the most important change is the move away from ARM specific includes and platform data. Together with this change the only in-tree board code gets an update, and the driver name is also changed gracefully break potential out of tree drivers. The driver is also updated to allow NULL as platform data together with a few changes to make use of resource_size() and dev_name(). Signed-off-by: Magnus Damm <damm@igel.co.jp> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Tony Lindgren <tony@atomide.com> Cc: Kyungmin Park <kmpark@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
74 lines
2.3 KiB
Plaintext
74 lines
2.3 KiB
Plaintext
#
|
|
# linux/drivers/mtd/onenand/Kconfig
|
|
#
|
|
|
|
menuconfig MTD_ONENAND
|
|
tristate "OneNAND Device Support"
|
|
depends on MTD
|
|
select MTD_PARTITIONS
|
|
help
|
|
This enables support for accessing all type of OneNAND flash
|
|
devices. For further information see
|
|
<http://www.samsung.com/Products/Semiconductor/OneNAND/index.htm>
|
|
|
|
if MTD_ONENAND
|
|
|
|
config MTD_ONENAND_VERIFY_WRITE
|
|
bool "Verify OneNAND page writes"
|
|
help
|
|
This adds an extra check when data is written to the flash. The
|
|
OneNAND flash device internally checks only bits transitioning
|
|
from 1 to 0. There is a rare possibility that even though the
|
|
device thinks the write was successful, a bit could have been
|
|
flipped accidentally due to device wear or something else.
|
|
|
|
config MTD_ONENAND_GENERIC
|
|
tristate "OneNAND Flash device via platform device driver"
|
|
help
|
|
Support for OneNAND flash via platform device driver.
|
|
|
|
config MTD_ONENAND_OMAP2
|
|
tristate "OneNAND on OMAP2/OMAP3 support"
|
|
depends on MTD_ONENAND && (ARCH_OMAP2 || ARCH_OMAP3)
|
|
help
|
|
Support for a OneNAND flash device connected to an OMAP2/OMAP3 CPU
|
|
via the GPMC memory controller.
|
|
|
|
config MTD_ONENAND_OTP
|
|
bool "OneNAND OTP Support"
|
|
select HAVE_MTD_OTP
|
|
help
|
|
One Block of the NAND Flash Array memory is reserved as
|
|
a One-Time Programmable Block memory area.
|
|
Also, 1st Block of NAND Flash Array can be used as OTP.
|
|
|
|
The OTP block can be read, programmed and locked using the same
|
|
operations as any other NAND Flash Array memory block.
|
|
OTP block cannot be erased.
|
|
|
|
OTP block is fully-guaranteed to be a valid block.
|
|
|
|
config MTD_ONENAND_2X_PROGRAM
|
|
bool "OneNAND 2X program support"
|
|
help
|
|
The 2X Program is an extension of Program Operation.
|
|
Since the device is equipped with two DataRAMs, and two-plane NAND
|
|
Flash memory array, these two component enables simultaneous program
|
|
of 4KiB. Plane1 has only even blocks such as block0, block2, block4
|
|
while Plane2 has only odd blocks such as block1, block3, block5.
|
|
So MTD regards it as 4KiB page size and 256KiB block size
|
|
|
|
Now the following chips support it. (KFXXX16Q2M)
|
|
Demux: KFG2G16Q2M, KFH4G16Q2M, KFW8G16Q2M,
|
|
Mux: KFM2G16Q2M, KFN4G16Q2M,
|
|
|
|
And more recent chips
|
|
|
|
config MTD_ONENAND_SIM
|
|
tristate "OneNAND simulator support"
|
|
help
|
|
The simulator may simulate various OneNAND flash chips for the
|
|
OneNAND MTD layer.
|
|
|
|
endif # MTD_ONENAND
|