AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity
7fbacd5213
kernel_optimize_test/drivers/serial/8250_pci.c
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2 
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

2304 lines
55 KiB
C
Raw Blame History

/*
* linux/drivers/char/8250_pci.c
*
* Probe module for 8250/16550-type PCI serial ports.
*
* Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
*
* Copyright (C) 2001 Russell King, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License.
*
* $Id: 8250_pci.c,v 1.28 2002/11/02 11:14:18 rmk Exp $
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/sched.h>
#include <linux/string.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/serial_core.h>
#include <linux/8250_pci.h>
#include <linux/bitops.h>
#include <asm/byteorder.h>
#include <asm/io.h>
#include "8250.h"
#undef SERIAL_DEBUG_PCI
/*
* Definitions for PCI support.
*/
#define FL_BASE_MASK 0x0007
#define FL_BASE0 0x0000
#define FL_BASE1 0x0001
#define FL_BASE2 0x0002
#define FL_BASE3 0x0003
#define FL_BASE4 0x0004
#define FL_GET_BASE(x) (x & FL_BASE_MASK)
/* Use successive BARs (PCI base address registers),
else use offset into some specified BAR */
#define FL_BASE_BARS 0x0008
/* do not assign an irq */
#define FL_NOIRQ 0x0080
/* Use the Base address register size to cap number of ports */
#define FL_REGION_SZ_CAP 0x0100
struct pci_board {
unsigned int flags;
unsigned int num_ports;
unsigned int base_baud;
unsigned int uart_offset;
unsigned int reg_shift;
unsigned int first_offset;
};
/*
* init function returns:
* > 0 - number of ports
* = 0 - use board->num_ports
* < 0 - error
*/
struct pci_serial_quirk {
u32 vendor;
u32 device;
u32 subvendor;
u32 subdevice;
int (*init)(struct pci_dev *dev);
int (*setup)(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx);
void (*exit)(struct pci_dev *dev);
};
#define PCI_NUM_BAR_RESOURCES 6
struct serial_private {
unsigned int nr;
void __iomem *remapped_bar[PCI_NUM_BAR_RESOURCES];
struct pci_serial_quirk *quirk;
int line[0];
};
static void moan_device(const char *str, struct pci_dev *dev)
{
printk(KERN_WARNING "%s: %s\n"
KERN_WARNING "Please send the output of lspci -vv, this\n"
KERN_WARNING "message (0x%04x,0x%04x,0x%04x,0x%04x), the\n"
KERN_WARNING "manufacturer and name of serial board or\n"
KERN_WARNING "modem board to rmk+serial@arm.linux.org.uk.\n",
pci_name(dev), str, dev->vendor, dev->device,
dev->subsystem_vendor, dev->subsystem_device);
}
static int
setup_port(struct pci_dev *dev, struct uart_port *port,
int bar, int offset, int regshift)
{
struct serial_private *priv = pci_get_drvdata(dev);
unsigned long base, len;
if (bar >= PCI_NUM_BAR_RESOURCES)
return -EINVAL;
if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
base = pci_resource_start(dev, bar);
len = pci_resource_len(dev, bar);
if (!priv->remapped_bar[bar])
priv->remapped_bar[bar] = ioremap(base, len);
if (!priv->remapped_bar[bar])
return -ENOMEM;
port->iotype = UPIO_MEM;
port->mapbase = base + offset;
port->membase = priv->remapped_bar[bar] + offset;
port->regshift = regshift;
} else {
base = pci_resource_start(dev, bar) + offset;
port->iotype = UPIO_PORT;
port->iobase = base;
}
return 0;
}
/*
* AFAVLAB uses a different mixture of BARs and offsets
* Not that ugly ;) -- HW
*/
static int
afavlab_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
bar = FL_GET_BASE(board->flags);
if (idx < 4)
bar += idx;
else {
bar = 4;
offset += (idx - 4) * board->uart_offset;
}
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/*
* HP's Remote Management Console. The Diva chip came in several
* different versions. N-class, L2000 and A500 have two Diva chips, each
* with 3 UARTs (the third UART on the second chip is unused). Superdome
* and Keystone have one Diva chip with 3 UARTs. Some later machines have
* one Diva chip, but it has been expanded to 5 UARTs.
*/
static int __devinit pci_hp_diva_init(struct pci_dev *dev)
{
int rc = 0;
switch (dev->subsystem_device) {
case PCI_DEVICE_ID_HP_DIVA_TOSCA1:
case PCI_DEVICE_ID_HP_DIVA_HALFDOME:
case PCI_DEVICE_ID_HP_DIVA_KEYSTONE:
case PCI_DEVICE_ID_HP_DIVA_EVEREST:
rc = 3;
break;
case PCI_DEVICE_ID_HP_DIVA_TOSCA2:
rc = 2;
break;
case PCI_DEVICE_ID_HP_DIVA_MAESTRO:
rc = 4;
break;
case PCI_DEVICE_ID_HP_DIVA_POWERBAR:
rc = 1;
break;
}
return rc;
}
/*
* HP's Diva chip puts the 4th/5th serial port further out, and
* some serial ports are supposed to be hidden on certain models.
*/
static int
pci_hp_diva_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int offset = board->first_offset;
unsigned int bar = FL_GET_BASE(board->flags);
switch (dev->subsystem_device) {
case PCI_DEVICE_ID_HP_DIVA_MAESTRO:
if (idx == 3)
idx++;
break;
case PCI_DEVICE_ID_HP_DIVA_EVEREST:
if (idx > 0)
idx++;
if (idx > 2)
idx++;
break;
}
if (idx > 2)
offset = 0x18;
offset += idx * board->uart_offset;
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/*
* Added for EKF Intel i960 serial boards
*/
static int __devinit pci_inteli960ni_init(struct pci_dev *dev)
{
unsigned long oldval;
if (!(dev->subsystem_device & 0x1000))
return -ENODEV;
/* is firmware started? */
pci_read_config_dword(dev, 0x44, (void*) &oldval);
if (oldval == 0x00001000L) { /* RESET value */
printk(KERN_DEBUG "Local i960 firmware missing");
return -ENODEV;
}
return 0;
}
/*
* Some PCI serial cards using the PLX 9050 PCI interface chip require
* that the card interrupt be explicitly enabled or disabled. This
* seems to be mainly needed on card using the PLX which also use I/O
* mapped memory.
*/
static int __devinit pci_plx9050_init(struct pci_dev *dev)
{
u8 irq_config;
void __iomem *p;
if ((pci_resource_flags(dev, 0) & IORESOURCE_MEM) == 0) {
moan_device("no memory in bar 0", dev);
return 0;
}
irq_config = 0x41;
if (dev->vendor == PCI_VENDOR_ID_PANACOM)
irq_config = 0x43;
if ((dev->vendor == PCI_VENDOR_ID_PLX) &&
(dev->device == PCI_DEVICE_ID_PLX_ROMULUS)) {
/*
* As the megawolf cards have the int pins active
* high, and have 2 UART chips, both ints must be
* enabled on the 9050. Also, the UARTS are set in
* 16450 mode by default, so we have to enable the
* 16C950 'enhanced' mode so that we can use the
* deep FIFOs
*/
irq_config = 0x5b;
}
/*
* enable/disable interrupts
*/
p = ioremap(pci_resource_start(dev, 0), 0x80);
if (p == NULL)
return -ENOMEM;
writel(irq_config, p + 0x4c);
/*
* Read the register back to ensure that it took effect.
*/
readl(p + 0x4c);
iounmap(p);
return 0;
}
static void __devexit pci_plx9050_exit(struct pci_dev *dev)
{
u8 __iomem *p;
if ((pci_resource_flags(dev, 0) & IORESOURCE_MEM) == 0)
return;
/*
* disable interrupts
*/
p = ioremap(pci_resource_start(dev, 0), 0x80);
if (p != NULL) {
writel(0, p + 0x4c);
/*
* Read the register back to ensure that it took effect.
*/
readl(p + 0x4c);
iounmap(p);
}
}
/* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */
static int
sbs_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
bar = 0;
if (idx < 4) {
/* first four channels map to 0, 0x100, 0x200, 0x300 */
offset += idx * board->uart_offset;
} else if (idx < 8) {
/* last four channels map to 0x1000, 0x1100, 0x1200, 0x1300 */
offset += idx * board->uart_offset + 0xC00;
} else /* we have only 8 ports on PMC-OCTALPRO */
return 1;
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/*
* This does initialization for PMC OCTALPRO cards:
* maps the device memory, resets the UARTs (needed, bc
* if the module is removed and inserted again, the card
* is in the sleep mode) and enables global interrupt.
*/
/* global control register offset for SBS PMC-OctalPro */
#define OCT_REG_CR_OFF 0x500
static int __devinit sbs_init(struct pci_dev *dev)
{
u8 __iomem *p;
p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
if (p == NULL)
return -ENOMEM;
/* Set bit-4 Control Register (UART RESET) in to reset the uarts */
writeb(0x10,p + OCT_REG_CR_OFF);
udelay(50);
writeb(0x0,p + OCT_REG_CR_OFF);
/* Set bit-2 (INTENABLE) of Control Register */
writeb(0x4, p + OCT_REG_CR_OFF);
iounmap(p);
return 0;
}
/*
* Disables the global interrupt of PMC-OctalPro
*/
static void __devexit sbs_exit(struct pci_dev *dev)
{
u8 __iomem *p;
p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
if (p != NULL) {
writeb(0, p + OCT_REG_CR_OFF);
}
iounmap(p);
}
/*
* SIIG serial cards have an PCI interface chip which also controls
* the UART clocking frequency. Each UART can be clocked independently
* (except cards equiped with 4 UARTs) and initial clocking settings
* are stored in the EEPROM chip. It can cause problems because this
* version of serial driver doesn't support differently clocked UART's
* on single PCI card. To prevent this, initialization functions set
* high frequency clocking for all UART's on given card. It is safe (I
* hope) because it doesn't touch EEPROM settings to prevent conflicts
* with other OSes (like M$ DOS).
*
* SIIG support added by Andrey Panin <pazke@donpac.ru>, 10/1999
*
* There is two family of SIIG serial cards with different PCI
* interface chip and different configuration methods:
* - 10x cards have control registers in IO and/or memory space;
* - 20x cards have control registers in standard PCI configuration space.
*
* Note: some SIIG cards are probed by the parport_serial object.
*/
#define PCI_DEVICE_ID_SIIG_1S_10x (PCI_DEVICE_ID_SIIG_1S_10x_550 & 0xfffc)
#define PCI_DEVICE_ID_SIIG_2S_10x (PCI_DEVICE_ID_SIIG_2S_10x_550 & 0xfff8)
static int pci_siig10x_init(struct pci_dev *dev)
{
u16 data;
void __iomem *p;
switch (dev->device & 0xfff8) {
case PCI_DEVICE_ID_SIIG_1S_10x: /* 1S */
data = 0xffdf;
break;
case PCI_DEVICE_ID_SIIG_2S_10x: /* 2S, 2S1P */
data = 0xf7ff;
break;
default: /* 1S1P, 4S */
data = 0xfffb;
break;
}
p = ioremap(pci_resource_start(dev, 0), 0x80);
if (p == NULL)
return -ENOMEM;
writew(readw(p + 0x28) & data, p + 0x28);
readw(p + 0x28);
iounmap(p);
return 0;
}
#define PCI_DEVICE_ID_SIIG_2S_20x (PCI_DEVICE_ID_SIIG_2S_20x_550 & 0xfffc)
#define PCI_DEVICE_ID_SIIG_2S1P_20x (PCI_DEVICE_ID_SIIG_2S1P_20x_550 & 0xfffc)
static int pci_siig20x_init(struct pci_dev *dev)
{
u8 data;
/* Change clock frequency for the first UART. */
pci_read_config_byte(dev, 0x6f, &data);
pci_write_config_byte(dev, 0x6f, data & 0xef);
/* If this card has 2 UART, we have to do the same with second UART. */
if (((dev->device & 0xfffc) == PCI_DEVICE_ID_SIIG_2S_20x) ||
((dev->device & 0xfffc) == PCI_DEVICE_ID_SIIG_2S1P_20x)) {
pci_read_config_byte(dev, 0x73, &data);
pci_write_config_byte(dev, 0x73, data & 0xef);
}
return 0;
}
int pci_siig10x_fn(struct pci_dev *dev, int enable)
{
int ret = 0;
if (enable)
ret = pci_siig10x_init(dev);
return ret;
}
int pci_siig20x_fn(struct pci_dev *dev, int enable)
{
int ret = 0;
if (enable)
ret = pci_siig20x_init(dev);
return ret;
}
EXPORT_SYMBOL(pci_siig10x_fn);
EXPORT_SYMBOL(pci_siig20x_fn);
/*
* Timedia has an explosion of boards, and to avoid the PCI table from
* growing *huge*, we use this function to collapse some 70 entries
* in the PCI table into one, for sanity's and compactness's sake.
*/
static unsigned short timedia_single_port[] = {
0x4025, 0x4027, 0x4028, 0x5025, 0x5027, 0
};
static unsigned short timedia_dual_port[] = {
0x0002, 0x4036, 0x4037, 0x4038, 0x4078, 0x4079, 0x4085,
0x4088, 0x4089, 0x5037, 0x5078, 0x5079, 0x5085, 0x6079,
0x7079, 0x8079, 0x8137, 0x8138, 0x8237, 0x8238, 0x9079,
0x9137, 0x9138, 0x9237, 0x9238, 0xA079, 0xB079, 0xC079,
0xD079, 0
};
static unsigned short timedia_quad_port[] = {
0x4055, 0x4056, 0x4095, 0x4096, 0x5056, 0x8156, 0x8157,
0x8256, 0x8257, 0x9056, 0x9156, 0x9157, 0x9158, 0x9159,
0x9256, 0x9257, 0xA056, 0xA157, 0xA158, 0xA159, 0xB056,
0xB157, 0
};
static unsigned short timedia_eight_port[] = {
0x4065, 0x4066, 0x5065, 0x5066, 0x8166, 0x9066, 0x9166,
0x9167, 0x9168, 0xA066, 0xA167, 0xA168, 0
};
static struct timedia_struct {
int num;
unsigned short *ids;
} timedia_data[] = {
{ 1, timedia_single_port },
{ 2, timedia_dual_port },
{ 4, timedia_quad_port },
{ 8, timedia_eight_port },
{ 0, NULL }
};
static int __devinit pci_timedia_init(struct pci_dev *dev)
{
unsigned short *ids;
int i, j;
for (i = 0; timedia_data[i].num; i++) {
ids = timedia_data[i].ids;
for (j = 0; ids[j]; j++)
if (dev->subsystem_device == ids[j])
return timedia_data[i].num;
}
return 0;
}
/*
* Timedia/SUNIX uses a mixture of BARs and offsets
* Ugh, this is ugly as all hell --- TYT
*/
static int
pci_timedia_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar = 0, offset = board->first_offset;
switch (idx) {
case 0:
bar = 0;
break;
case 1:
offset = board->uart_offset;
bar = 0;
break;
case 2:
bar = 1;
break;
case 3:
offset = board->uart_offset;
bar = 1;
case 4: /* BAR 2 */
case 5: /* BAR 3 */
case 6: /* BAR 4 */
case 7: /* BAR 5 */
bar = idx - 2;
}
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/*
* Some Titan cards are also a little weird
*/
static int
titan_400l_800l_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
switch (idx) {
case 0:
bar = 1;
break;
case 1:
bar = 2;
break;
default:
bar = 4;
offset = (idx - 2) * board->uart_offset;
}
return setup_port(dev, port, bar, offset, board->reg_shift);
}
static int __devinit pci_xircom_init(struct pci_dev *dev)
{
msleep(100);
return 0;
}
static int __devinit pci_netmos_init(struct pci_dev *dev)
{
/* subdevice 0x00PS means <P> parallel, <S> serial */
unsigned int num_serial = dev->subsystem_device & 0xf;
if (num_serial == 0)
return -ENODEV;
return num_serial;
}
static int
pci_default_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset, maxnr;
bar = FL_GET_BASE(board->flags);
if (board->flags & FL_BASE_BARS)
bar += idx;
else
offset += idx * board->uart_offset;
maxnr = (pci_resource_len(dev, bar) - board->first_offset) /
(8 << board->reg_shift);
if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr)
return 1;
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/* This should be in linux/pci_ids.h */
#define PCI_VENDOR_ID_SBSMODULARIO 0x124B
#define PCI_SUBVENDOR_ID_SBSMODULARIO 0x124B
#define PCI_DEVICE_ID_OCTPRO 0x0001
#define PCI_SUBDEVICE_ID_OCTPRO232 0x0108
#define PCI_SUBDEVICE_ID_OCTPRO422 0x0208
#define PCI_SUBDEVICE_ID_POCTAL232 0x0308
#define PCI_SUBDEVICE_ID_POCTAL422 0x0408
/*
* Master list of serial port init/setup/exit quirks.
* This does not describe the general nature of the port.
* (ie, baud base, number and location of ports, etc)
*
* This list is ordered alphabetically by vendor then device.
* Specific entries must come before more generic entries.
*/
static struct pci_serial_quirk pci_serial_quirks[] = {
/*
* AFAVLAB cards.
* It is not clear whether this applies to all products.
*/
{
.vendor = PCI_VENDOR_ID_AFAVLAB,
.device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = afavlab_setup,
},
/*
* HP Diva
*/
{
.vendor = PCI_VENDOR_ID_HP,
.device = PCI_DEVICE_ID_HP_DIVA,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_hp_diva_init,
.setup = pci_hp_diva_setup,
},
/*
* Intel
*/
{
.vendor = PCI_VENDOR_ID_INTEL,
.device = PCI_DEVICE_ID_INTEL_80960_RP,
.subvendor = 0xe4bf,
.subdevice = PCI_ANY_ID,
.init = pci_inteli960ni_init,
.setup = pci_default_setup,
},
/*
* Panacom
*/
{
.vendor = PCI_VENDOR_ID_PANACOM,
.device = PCI_DEVICE_ID_PANACOM_QUADMODEM,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
{
.vendor = PCI_VENDOR_ID_PANACOM,
.device = PCI_DEVICE_ID_PANACOM_DUALMODEM,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
/*
* PLX
*/
{
.vendor = PCI_VENDOR_ID_PLX,
.device = PCI_DEVICE_ID_PLX_9050,
.subvendor = PCI_SUBVENDOR_ID_KEYSPAN,
.subdevice = PCI_SUBDEVICE_ID_KEYSPAN_SX2,
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
{
.vendor = PCI_VENDOR_ID_PLX,
.device = PCI_DEVICE_ID_PLX_ROMULUS,
.subvendor = PCI_VENDOR_ID_PLX,
.subdevice = PCI_DEVICE_ID_PLX_ROMULUS,
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
/*
* SBS Technologies, Inc., PMC-OCTALPRO 232
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_OCTPRO232,
.init = sbs_init,
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
/*
* SBS Technologies, Inc., PMC-OCTALPRO 422
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_OCTPRO422,
.init = sbs_init,
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
/*
* SBS Technologies, Inc., P-Octal 232
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_POCTAL232,
.init = sbs_init,
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
/*
* SBS Technologies, Inc., P-Octal 422
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_POCTAL422,
.init = sbs_init,
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
/*
* SIIG cards.
* It is not clear whether these could be collapsed.
*/
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_10x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_10x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_10x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_10x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_10x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_10x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_10x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_10x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_10x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_20x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_20x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_20x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_20x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{ .vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_20x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_20x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_20x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_20x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_20x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
/*
* Titan cards
*/
{
.vendor = PCI_VENDOR_ID_TITAN,
.device = PCI_DEVICE_ID_TITAN_400L,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = titan_400l_800l_setup,
},
{
.vendor = PCI_VENDOR_ID_TITAN,
.device = PCI_DEVICE_ID_TITAN_800L,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = titan_400l_800l_setup,
},
/*
* Timedia cards
*/
{
.vendor = PCI_VENDOR_ID_TIMEDIA,
.device = PCI_DEVICE_ID_TIMEDIA_1889,
.subvendor = PCI_VENDOR_ID_TIMEDIA,
.subdevice = PCI_ANY_ID,
.init = pci_timedia_init,
.setup = pci_timedia_setup,
},
{
.vendor = PCI_VENDOR_ID_TIMEDIA,
.device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_timedia_setup,
},
/*
* Xircom cards
*/
{
.vendor = PCI_VENDOR_ID_XIRCOM,
.device = PCI_DEVICE_ID_XIRCOM_X3201_MDM,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_xircom_init,
.setup = pci_default_setup,
},
/*
* Netmos cards
*/
{
.vendor = PCI_VENDOR_ID_NETMOS,
.device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_netmos_init,
.setup = pci_default_setup,
},
/*
* Default "match everything" terminator entry
*/
{
.vendor = PCI_ANY_ID,
.device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_default_setup,
}
};
static inline int quirk_id_matches(u32 quirk_id, u32 dev_id)
{
return quirk_id == PCI_ANY_ID || quirk_id == dev_id;
}
static struct pci_serial_quirk *find_quirk(struct pci_dev *dev)
{
struct pci_serial_quirk *quirk;
for (quirk = pci_serial_quirks; ; quirk++)
if (quirk_id_matches(quirk->vendor, dev->vendor) &&
quirk_id_matches(quirk->device, dev->device) &&
quirk_id_matches(quirk->subvendor, dev->subsystem_vendor) &&
quirk_id_matches(quirk->subdevice, dev->subsystem_device))
break;
return quirk;
}
static _INLINE_ int
get_pci_irq(struct pci_dev *dev, struct pci_board *board, int idx)
{
if (board->flags & FL_NOIRQ)
return 0;
else
return dev->irq;
}
/*
* This is the configuration table for all of the PCI serial boards
* which we support. It is directly indexed by the pci_board_num_t enum
* value, which is encoded in the pci_device_id PCI probe table's
* driver_data member.
*
* The makeup of these names are:
* pbn_bn{_bt}_n_baud
*
* bn = PCI BAR number
* bt = Index using PCI BARs
* n = number of serial ports
* baud = baud rate
*
* Please note: in theory if n = 1, _bt infix should make no difference.
* ie, pbn_b0_1_115200 is the same as pbn_b0_bt_1_115200
*/
enum pci_board_num_t {
pbn_default = 0,
pbn_b0_1_115200,
pbn_b0_2_115200,
pbn_b0_4_115200,
pbn_b0_5_115200,
pbn_b0_1_921600,
pbn_b0_2_921600,
pbn_b0_4_921600,
pbn_b0_bt_1_115200,
pbn_b0_bt_2_115200,
pbn_b0_bt_8_115200,
pbn_b0_bt_1_460800,
pbn_b0_bt_2_460800,
pbn_b0_bt_4_460800,
pbn_b0_bt_1_921600,
pbn_b0_bt_2_921600,
pbn_b0_bt_4_921600,
pbn_b0_bt_8_921600,
pbn_b1_1_115200,
pbn_b1_2_115200,
pbn_b1_4_115200,
pbn_b1_8_115200,
pbn_b1_1_921600,
pbn_b1_2_921600,
pbn_b1_4_921600,
pbn_b1_8_921600,
pbn_b1_bt_2_921600,
pbn_b1_1_1382400,
pbn_b1_2_1382400,
pbn_b1_4_1382400,
pbn_b1_8_1382400,
pbn_b2_1_115200,
pbn_b2_8_115200,
pbn_b2_1_460800,
pbn_b2_4_460800,
pbn_b2_8_460800,
pbn_b2_16_460800,
pbn_b2_1_921600,
pbn_b2_4_921600,
pbn_b2_8_921600,
pbn_b2_bt_1_115200,
pbn_b2_bt_2_115200,
pbn_b2_bt_4_115200,
pbn_b2_bt_2_921600,
pbn_b2_bt_4_921600,
pbn_b3_4_115200,
pbn_b3_8_115200,
/*
* Board-specific versions.
*/
pbn_panacom,
pbn_panacom2,
pbn_panacom4,
pbn_plx_romulus,
pbn_oxsemi,
pbn_intel_i960,
pbn_sgi_ioc3,
pbn_nec_nile4,
pbn_computone_4,
pbn_computone_6,
pbn_computone_8,
pbn_sbsxrsio,
pbn_exar_XR17C152,
pbn_exar_XR17C154,
pbn_exar_XR17C158,
};
/*
* uart_offset - the space between channels
* reg_shift - describes how the UART registers are mapped
* to PCI memory by the card.
* For example IER register on SBS, Inc. PMC-OctPro is located at
* offset 0x10 from the UART base, while UART_IER is defined as 1
* in include/linux/serial_reg.h,
* see first lines of serial_in() and serial_out() in 8250.c
*/
static struct pci_board pci_boards[] __devinitdata = {
[pbn_default] = {
.flags = FL_BASE0,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_1_115200] = {
.flags = FL_BASE0,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_2_115200] = {
.flags = FL_BASE0,
.num_ports = 2,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_4_115200] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_5_115200] = {
.flags = FL_BASE0,
.num_ports = 5,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_1_921600] = {
.flags = FL_BASE0,
.num_ports = 1,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_2_921600] = {
.flags = FL_BASE0,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_4_921600] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_bt_1_115200] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_bt_2_115200] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_bt_8_115200] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 8,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_bt_1_460800] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 1,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b0_bt_2_460800] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b0_bt_4_460800] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b0_bt_1_921600] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 1,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_bt_2_921600] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_bt_4_921600] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_bt_8_921600] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_1_115200] = {
.flags = FL_BASE1,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b1_2_115200] = {
.flags = FL_BASE1,
.num_ports = 2,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b1_4_115200] = {
.flags = FL_BASE1,
.num_ports = 4,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b1_8_115200] = {
.flags = FL_BASE1,
.num_ports = 8,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b1_1_921600] = {
.flags = FL_BASE1,
.num_ports = 1,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_2_921600] = {
.flags = FL_BASE1,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_4_921600] = {
.flags = FL_BASE1,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_8_921600] = {
.flags = FL_BASE1,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_bt_2_921600] = {
.flags = FL_BASE1|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_1_1382400] = {
.flags = FL_BASE1,
.num_ports = 1,
.base_baud = 1382400,
.uart_offset = 8,
},
[pbn_b1_2_1382400] = {
.flags = FL_BASE1,
.num_ports = 2,
.base_baud = 1382400,
.uart_offset = 8,
},
[pbn_b1_4_1382400] = {
.flags = FL_BASE1,
.num_ports = 4,
.base_baud = 1382400,
.uart_offset = 8,
},
[pbn_b1_8_1382400] = {
.flags = FL_BASE1,
.num_ports = 8,
.base_baud = 1382400,
.uart_offset = 8,
},
[pbn_b2_1_115200] = {
.flags = FL_BASE2,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_8_115200] = {
.flags = FL_BASE2,
.num_ports = 8,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_1_460800] = {
.flags = FL_BASE2,
.num_ports = 1,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b2_4_460800] = {
.flags = FL_BASE2,
.num_ports = 4,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b2_8_460800] = {
.flags = FL_BASE2,
.num_ports = 8,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b2_16_460800] = {
.flags = FL_BASE2,
.num_ports = 16,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b2_1_921600] = {
.flags = FL_BASE2,
.num_ports = 1,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b2_4_921600] = {
.flags = FL_BASE2,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b2_8_921600] = {
.flags = FL_BASE2,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b2_bt_1_115200] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_bt_2_115200] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_bt_4_115200] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_bt_2_921600] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b2_bt_4_921600] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b3_4_115200] = {
.flags = FL_BASE3,
.num_ports = 4,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b3_8_115200] = {
.flags = FL_BASE3,
.num_ports = 8,
.base_baud = 115200,
.uart_offset = 8,
},
/*
* Entries following this are board-specific.
*/
/*
* Panacom - IOMEM
*/
[pbn_panacom] = {
.flags = FL_BASE2,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 0x400,
.reg_shift = 7,
},
[pbn_panacom2] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 0x400,
.reg_shift = 7,
},
[pbn_panacom4] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 0x400,
.reg_shift = 7,
},
/* I think this entry is broken - the first_offset looks wrong --rmk */
[pbn_plx_romulus] = {
.flags = FL_BASE2,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8 << 2,
.reg_shift = 2,
.first_offset = 0x03,
},
/*
* This board uses the size of PCI Base region 0 to
* signal now many ports are available
*/
[pbn_oxsemi] = {
.flags = FL_BASE0|FL_REGION_SZ_CAP,
.num_ports = 32,
.base_baud = 115200,
.uart_offset = 8,
},
/*
* EKF addition for i960 Boards form EKF with serial port.
* Max 256 ports.
*/
[pbn_intel_i960] = {
.flags = FL_BASE0,
.num_ports = 32,
.base_baud = 921600,
.uart_offset = 8 << 2,
.reg_shift = 2,
.first_offset = 0x10000,
},
[pbn_sgi_ioc3] = {
.flags = FL_BASE0|FL_NOIRQ,
.num_ports = 1,
.base_baud = 458333,
.uart_offset = 8,
.reg_shift = 0,
.first_offset = 0x20178,
},
/*
* NEC Vrc-5074 (Nile 4) builtin UART.
*/
[pbn_nec_nile4] = {
.flags = FL_BASE0,
.num_ports = 1,
.base_baud = 520833,
.uart_offset = 8 << 3,
.reg_shift = 3,
.first_offset = 0x300,
},
/*
* Computone - uses IOMEM.
*/
[pbn_computone_4] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 0x40,
.reg_shift = 2,
.first_offset = 0x200,
},
[pbn_computone_6] = {
.flags = FL_BASE0,
.num_ports = 6,
.base_baud = 921600,
.uart_offset = 0x40,
.reg_shift = 2,
.first_offset = 0x200,
},
[pbn_computone_8] = {
.flags = FL_BASE0,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 0x40,
.reg_shift = 2,
.first_offset = 0x200,
},
[pbn_sbsxrsio] = {
.flags = FL_BASE0,
.num_ports = 8,
.base_baud = 460800,
.uart_offset = 256,
.reg_shift = 4,
},
/*
* Exar Corp. XR17C15[248] Dual/Quad/Octal UART
* Only basic 16550A support.
* XR17C15[24] are not tested, but they should work.
*/
[pbn_exar_XR17C152] = {
.flags = FL_BASE0,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 0x200,
},
[pbn_exar_XR17C154] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 0x200,
},
[pbn_exar_XR17C158] = {
.flags = FL_BASE0,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 0x200,
},
};
/*
* Given a complete unknown PCI device, try to use some heuristics to
* guess what the configuration might be, based on the pitiful PCI
* serial specs. Returns 0 on success, 1 on failure.
*/
static int __devinit
serial_pci_guess_board(struct pci_dev *dev, struct pci_board *board)
{
int num_iomem, num_port, first_port = -1, i;
/*
* If it is not a communications device or the programming
* interface is greater than 6, give up.
*
* (Should we try to make guesses for multiport serial devices
* later?)
*/
if ((((dev->class >> 8) != PCI_CLASS_COMMUNICATION_SERIAL) &&
((dev->class >> 8) != PCI_CLASS_COMMUNICATION_MODEM)) ||
(dev->class & 0xff) > 6)
return -ENODEV;
num_iomem = num_port = 0;
for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
if (pci_resource_flags(dev, i) & IORESOURCE_IO) {
num_port++;
if (first_port == -1)
first_port = i;
}
if (pci_resource_flags(dev, i) & IORESOURCE_MEM)
num_iomem++;
}
/*
* If there is 1 or 0 iomem regions, and exactly one port,
* use it. We guess the number of ports based on the IO
* region size.
*/
if (num_iomem <= 1 && num_port == 1) {
board->flags = first_port;
board->num_ports = pci_resource_len(dev, first_port) / 8;
return 0;
}
/*
* Now guess if we've got a board which indexes by BARs.
* Each IO BAR should be 8 bytes, and they should follow
* consecutively.
*/
first_port = -1;
num_port = 0;
for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
if (pci_resource_flags(dev, i) & IORESOURCE_IO &&
pci_resource_len(dev, i) == 8 &&
(first_port == -1 || (first_port + num_port) == i)) {
num_port++;
if (first_port == -1)
first_port = i;
}
}
if (num_port > 1) {
board->flags = first_port | FL_BASE_BARS;
board->num_ports = num_port;
return 0;
}
return -ENODEV;
}
static inline int
serial_pci_matches(struct pci_board *board, struct pci_board *guessed)
{
return
board->num_ports == guessed->num_ports &&
board->base_baud == guessed->base_baud &&
board->uart_offset == guessed->uart_offset &&
board->reg_shift == guessed->reg_shift &&
board->first_offset == guessed->first_offset;
}
/*
* Probe one serial board. Unfortunately, there is no rhyme nor reason
* to the arrangement of serial ports on a PCI card.
*/
static int __devinit
pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
{
struct serial_private *priv;
struct pci_board *board, tmp;
struct pci_serial_quirk *quirk;
int rc, nr_ports, i;
if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
printk(KERN_ERR "pci_init_one: invalid driver_data: %ld\n",
ent->driver_data);
return -EINVAL;
}
board = &pci_boards[ent->driver_data];
rc = pci_enable_device(dev);
if (rc)
return rc;
if (ent->driver_data == pbn_default) {
/*
* Use a copy of the pci_board entry for this;
* avoid changing entries in the table.
*/
memcpy(&tmp, board, sizeof(struct pci_board));
board = &tmp;
/*
* We matched one of our class entries. Try to
* determine the parameters of this board.
*/
rc = serial_pci_guess_board(dev, board);
if (rc)
goto disable;
} else {
/*
* We matched an explicit entry. If we are able to
* detect this boards settings with our heuristic,
* then we no longer need this entry.
*/
memcpy(&tmp, &pci_boards[pbn_default], sizeof(struct pci_board));
rc = serial_pci_guess_board(dev, &tmp);
if (rc == 0 && serial_pci_matches(board, &tmp))
moan_device("Redundant entry in serial pci_table.",
dev);
}
nr_ports = board->num_ports;
/*
* Find an init and setup quirks.
*/
quirk = find_quirk(dev);
/*
* Run the new-style initialization function.
* The initialization function returns:
* <0 - error
* 0 - use board->num_ports
* >0 - number of ports
*/
if (quirk->init) {
rc = quirk->init(dev);
if (rc < 0)
goto disable;
if (rc)
nr_ports = rc;
}
priv = kmalloc(sizeof(struct serial_private) +
sizeof(unsigned int) * nr_ports,
GFP_KERNEL);
if (!priv) {
rc = -ENOMEM;
goto deinit;
}
memset(priv, 0, sizeof(struct serial_private) +
sizeof(unsigned int) * nr_ports);
priv->quirk = quirk;
pci_set_drvdata(dev, priv);
for (i = 0; i < nr_ports; i++) {
struct uart_port serial_port;
memset(&serial_port, 0, sizeof(struct uart_port));
serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF |
UPF_SHARE_IRQ;
serial_port.uartclk = board->base_baud * 16;
serial_port.irq = get_pci_irq(dev, board, i);
serial_port.dev = &dev->dev;
if (quirk->setup(dev, board, &serial_port, i))
break;
#ifdef SERIAL_DEBUG_PCI
printk("Setup PCI port: port %x, irq %d, type %d\n",
serial_port.iobase, serial_port.irq, serial_port.iotype);
#endif
priv->line[i] = serial8250_register_port(&serial_port);
if (priv->line[i] < 0) {
printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), priv->line[i]);
break;
}
}
priv->nr = i;
return 0;
deinit:
if (quirk->exit)
quirk->exit(dev);
disable:
pci_disable_device(dev);
return rc;
}
static void __devexit pciserial_remove_one(struct pci_dev *dev)
{
struct serial_private *priv = pci_get_drvdata(dev);
pci_set_drvdata(dev, NULL);
if (priv) {
struct pci_serial_quirk *quirk;
int i;
for (i = 0; i < priv->nr; i++)
serial8250_unregister_port(priv->line[i]);
for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
if (priv->remapped_bar[i])
iounmap(priv->remapped_bar[i]);
priv->remapped_bar[i] = NULL;
}
/*
* Find the exit quirks.
*/
quirk = find_quirk(dev);
if (quirk->exit)
quirk->exit(dev);
pci_disable_device(dev);
kfree(priv);
}
}
static int pciserial_suspend_one(struct pci_dev *dev, pm_message_t state)
{
struct serial_private *priv = pci_get_drvdata(dev);
if (priv) {
int i;
for (i = 0; i < priv->nr; i++)
serial8250_suspend_port(priv->line[i]);
}
pci_save_state(dev);
pci_set_power_state(dev, pci_choose_state(dev, state));
return 0;
}
static int pciserial_resume_one(struct pci_dev *dev)
{
struct serial_private *priv = pci_get_drvdata(dev);
pci_set_power_state(dev, PCI_D0);
pci_restore_state(dev);
if (priv) {
int i;
/*
* The device may have been disabled. Re-enable it.
*/
pci_enable_device(dev);
/*
* Ensure that the board is correctly configured.
*/
if (priv->quirk->init)
priv->quirk->init(dev);
for (i = 0; i < priv->nr; i++)
serial8250_resume_port(priv->line[i]);
}
return 0;
}
static struct pci_device_id serial_pci_tbl[] = {
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
pbn_b1_8_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_232, 0, 0,
pbn_b1_4_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232, 0, 0,
pbn_b1_2_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
pbn_b1_8_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_232, 0, 0,
pbn_b1_4_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232, 0, 0,
pbn_b1_2_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485, 0, 0,
pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_4_4, 0, 0,
pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485, 0, 0,
pbn_b1_4_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485_2_2, 0, 0,
pbn_b1_4_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_485, 0, 0,
pbn_b1_2_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_2_6, 0, 0,
pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH081101V1, 0, 0,
pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH041101V1, 0, 0,
pbn_b1_4_921600 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_U530,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_1_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM422,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM232,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_COMM4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_COMM8,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_8_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM8,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_8_115200 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_GTEK_SERIAL2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_SPCOM200,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_921600 },
/*
* VScom SPCOM800, from sl@s.pl
*/
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_SPCOM800,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_8_921600 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_1077,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_4_921600 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_KEYSPAN,
PCI_SUBDEVICE_ID_KEYSPAN_SX2, 0, 0,
pbn_panacom },
{ PCI_VENDOR_ID_PANACOM, PCI_DEVICE_ID_PANACOM_QUADMODEM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_panacom4 },
{ PCI_VENDOR_ID_PANACOM, PCI_DEVICE_ID_PANACOM_DUALMODEM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_panacom2 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
PCI_SUBDEVICE_ID_CHASE_PCIFAST4, 0, 0,
pbn_b2_4_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
PCI_SUBDEVICE_ID_CHASE_PCIFAST8, 0, 0,
pbn_b2_8_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
PCI_SUBDEVICE_ID_CHASE_PCIFAST16, 0, 0,
pbn_b2_16_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
PCI_SUBDEVICE_ID_CHASE_PCIFAST16FMC, 0, 0,
pbn_b2_16_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIRAS,
PCI_SUBDEVICE_ID_CHASE_PCIRAS4, 0, 0,
pbn_b2_4_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIRAS,
PCI_SUBDEVICE_ID_CHASE_PCIRAS8, 0, 0,
pbn_b2_8_460800 },
/*
* Megawolf Romulus PCI Serial Card, from Mike Hudson
* (Exoray@isys.ca)
*/
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_ROMULUS,
0x10b5, 0x106a, 0, 0,
pbn_plx_romulus },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSC100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_4_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSC100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_2_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100D,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100M,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
{ PCI_VENDOR_ID_SPECIALIX, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4, 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_115200 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_921600 },
/*
* SBS Technologies, Inc. P-Octal and PMC-OCTPRO cards,
* from skokodyn@yahoo.com
*/
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_OCTPRO232, 0, 0,
pbn_sbsxrsio },
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_OCTPRO422, 0, 0,
pbn_sbsxrsio },
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_POCTAL232, 0, 0,
pbn_sbsxrsio },
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_POCTAL422, 0, 0,
pbn_sbsxrsio },
/*
* Digitan DS560-558, from jimd@esoft.com
*/
{ PCI_VENDOR_ID_ATT, PCI_DEVICE_ID_ATT_VENUS_MODEM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_1_115200 },
/*
* Titan Electronic cards
* The 400L and 800L have a custom setup quirk.
*/
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_200,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_2_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_400,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_800B,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_100L,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_1_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_200L,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_bt_2_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_400L,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_800L,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_8_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_10x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_460800 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_10x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_460800 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_10x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_460800 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_10x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_10x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_10x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_10x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_10x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_10x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_20x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_20x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_20x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_20x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_20x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_20x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_921600 },
/*
* Computone devices submitted by Doug McNash dmcnash@computone.com
*/
{ PCI_VENDOR_ID_COMPUTONE, PCI_DEVICE_ID_COMPUTONE_PG,
PCI_SUBVENDOR_ID_COMPUTONE, PCI_SUBDEVICE_ID_COMPUTONE_PG4,
0, 0, pbn_computone_4 },
{ PCI_VENDOR_ID_COMPUTONE, PCI_DEVICE_ID_COMPUTONE_PG,
PCI_SUBVENDOR_ID_COMPUTONE, PCI_SUBDEVICE_ID_COMPUTONE_PG8,
0, 0, pbn_computone_8 },
{ PCI_VENDOR_ID_COMPUTONE, PCI_DEVICE_ID_COMPUTONE_PG,
PCI_SUBVENDOR_ID_COMPUTONE, PCI_SUBDEVICE_ID_COMPUTONE_PG6,
0, 0, pbn_computone_6 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI95N,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_oxsemi },
{ PCI_VENDOR_ID_TIMEDIA, PCI_DEVICE_ID_TIMEDIA_1889,
PCI_VENDOR_ID_TIMEDIA, PCI_ANY_ID, 0, 0,
pbn_b0_bt_1_921600 },
/*
* AFAVLAB serial card, from Harald Welte <laforge@gnumonks.org>
*/
{ PCI_VENDOR_ID_AFAVLAB, PCI_DEVICE_ID_AFAVLAB_P028,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_8_115200 },
{ PCI_VENDOR_ID_AFAVLAB, PCI_DEVICE_ID_AFAVLAB_P030,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_8_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DSERIAL,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUATRO_A,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUATRO_B,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_OCTO_A,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_OCTO_B,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PORT_PLUS,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUAD_A,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUAD_B,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_SSERIAL,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_1_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PORT_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_1_460800 },
/*
* Dell Remote Access Card 4 - Tim_T_Murphy@Dell.com
*/
{ PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_RAC4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_1_1382400 },
/*
* Dell Remote Access Card III - Tim_T_Murphy@Dell.com
*/
{ PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_RACIII,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_1_1382400 },
/*
* RAStel 2 port modem, gerg@moreton.com.au
*/
{ PCI_VENDOR_ID_MORETON, PCI_DEVICE_ID_RASTEL_2PORT,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
/*
* EKF addition for i960 Boards form EKF with serial port
*/
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80960_RP,
0xE4BF, PCI_ANY_ID, 0, 0,
pbn_intel_i960 },
/*
* Xircom Cardbus/Ethernet combos
*/
{ PCI_VENDOR_ID_XIRCOM, PCI_DEVICE_ID_XIRCOM_X3201_MDM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_115200 },
/*
* Xircom RBM56G cardbus modem - Dirk Arnold (temp entry)
*/
{ PCI_VENDOR_ID_XIRCOM, PCI_DEVICE_ID_XIRCOM_RBM56G,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_115200 },
/*
* Untested PCI modems, sent in from various folks...
*/
/*
* Elsa Model 56K PCI Modem, from Andreas Rath <arh@01019freenet.de>
*/
{ PCI_VENDOR_ID_ROCKWELL, 0x1004,
0x1048, 0x1500, 0, 0,
pbn_b1_1_115200 },
{ PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3,
0xFF00, 0, 0, 0,
pbn_sgi_ioc3 },
/*
* HP Diva card
*/
{ PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA,
PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA_RMP3, 0, 0,
pbn_b1_1_115200 },
{ PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_5_115200 },
{ PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA_AUX,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_115200 },
/*
* NEC Vrc-5074 (Nile 4) builtin UART.
*/
{ PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_NILE4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_nec_nile4 },
{ PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b3_4_115200 },
{ PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM8,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b3_8_115200 },
/*
* Exar Corp. XR17C15[248] Dual/Quad/Octal UART
*/
{ PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17C152 },
{ PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17C154 },
{ PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17C158 },
/*
* Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke)
*/
{ PCI_VENDOR_ID_TOPIC, PCI_DEVICE_ID_TOPIC_TP560,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_115200 },
/*
* These entries match devices with class COMMUNICATION_SERIAL,
* COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL
*/
{ PCI_ANY_ID, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_COMMUNICATION_SERIAL << 8,
0xffff00, pbn_default },
{ PCI_ANY_ID, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_COMMUNICATION_MODEM << 8,
0xffff00, pbn_default },
{ PCI_ANY_ID, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_COMMUNICATION_MULTISERIAL << 8,
0xffff00, pbn_default },
{ 0, }
};
static struct pci_driver serial_pci_driver = {
.name = "serial",
.probe = pciserial_init_one,
.remove = __devexit_p(pciserial_remove_one),
.suspend = pciserial_suspend_one,
.resume = pciserial_resume_one,
.id_table = serial_pci_tbl,
};
static int __init serial8250_pci_init(void)
{
return pci_register_driver(&serial_pci_driver);
}
static void __exit serial8250_pci_exit(void)
{
pci_unregister_driver(&serial_pci_driver);
}
module_init(serial8250_pci_init);
module_exit(serial8250_pci_exit);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Generic 8250/16x50 PCI serial probe module");
MODULE_DEVICE_TABLE(pci, serial_pci_tbl);
View Git Blame Copy Permalink