kernel_optimize_test/drivers/gpio/gpio-davinci.c
Krzysztof Kozlowski 33b78b5f14 gpio: davinci: Simplify with dev_err_probe()
Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-08-28 20:15:06 +02:00

652 lines
17 KiB
C

// SPDX-License-Identifier: GPL-2.0-or-later
/*
* TI DaVinci GPIO Support
*
* Copyright (c) 2006-2007 David Brownell
* Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com>
*/
#include <linux/gpio/driver.h>
#include <linux/errno.h>
#include <linux/kernel.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/irqdomain.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/pinctrl/consumer.h>
#include <linux/platform_device.h>
#include <linux/platform_data/gpio-davinci.h>
#include <linux/irqchip/chained_irq.h>
#include <linux/spinlock.h>
#include <asm-generic/gpio.h>
#define MAX_REGS_BANKS 5
#define MAX_INT_PER_BANK 32
struct davinci_gpio_regs {
u32 dir;
u32 out_data;
u32 set_data;
u32 clr_data;
u32 in_data;
u32 set_rising;
u32 clr_rising;
u32 set_falling;
u32 clr_falling;
u32 intstat;
};
typedef struct irq_chip *(*gpio_get_irq_chip_cb_t)(unsigned int irq);
#define BINTEN 0x8 /* GPIO Interrupt Per-Bank Enable Register */
static void __iomem *gpio_base;
static unsigned int offset_array[5] = {0x10, 0x38, 0x60, 0x88, 0xb0};
struct davinci_gpio_irq_data {
void __iomem *regs;
struct davinci_gpio_controller *chip;
int bank_num;
};
struct davinci_gpio_controller {
struct gpio_chip chip;
struct irq_domain *irq_domain;
/* Serialize access to GPIO registers */
spinlock_t lock;
void __iomem *regs[MAX_REGS_BANKS];
int gpio_unbanked;
int irqs[MAX_INT_PER_BANK];
};
static inline u32 __gpio_mask(unsigned gpio)
{
return 1 << (gpio % 32);
}
static inline struct davinci_gpio_regs __iomem *irq2regs(struct irq_data *d)
{
struct davinci_gpio_regs __iomem *g;
g = (__force struct davinci_gpio_regs __iomem *)irq_data_get_irq_chip_data(d);
return g;
}
static int davinci_gpio_irq_setup(struct platform_device *pdev);
/*--------------------------------------------------------------------------*/
/* board setup code *MUST* setup pinmux and enable the GPIO clock. */
static inline int __davinci_direction(struct gpio_chip *chip,
unsigned offset, bool out, int value)
{
struct davinci_gpio_controller *d = gpiochip_get_data(chip);
struct davinci_gpio_regs __iomem *g;
unsigned long flags;
u32 temp;
int bank = offset / 32;
u32 mask = __gpio_mask(offset);
g = d->regs[bank];
spin_lock_irqsave(&d->lock, flags);
temp = readl_relaxed(&g->dir);
if (out) {
temp &= ~mask;
writel_relaxed(mask, value ? &g->set_data : &g->clr_data);
} else {
temp |= mask;
}
writel_relaxed(temp, &g->dir);
spin_unlock_irqrestore(&d->lock, flags);
return 0;
}
static int davinci_direction_in(struct gpio_chip *chip, unsigned offset)
{
return __davinci_direction(chip, offset, false, 0);
}
static int
davinci_direction_out(struct gpio_chip *chip, unsigned offset, int value)
{
return __davinci_direction(chip, offset, true, value);
}
/*
* Read the pin's value (works even if it's set up as output);
* returns zero/nonzero.
*
* Note that changes are synched to the GPIO clock, so reading values back
* right after you've set them may give old values.
*/
static int davinci_gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct davinci_gpio_controller *d = gpiochip_get_data(chip);
struct davinci_gpio_regs __iomem *g;
int bank = offset / 32;
g = d->regs[bank];
return !!(__gpio_mask(offset) & readl_relaxed(&g->in_data));
}
/*
* Assuming the pin is muxed as a gpio output, set its output value.
*/
static void
davinci_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
{
struct davinci_gpio_controller *d = gpiochip_get_data(chip);
struct davinci_gpio_regs __iomem *g;
int bank = offset / 32;
g = d->regs[bank];
writel_relaxed(__gpio_mask(offset),
value ? &g->set_data : &g->clr_data);
}
static struct davinci_gpio_platform_data *
davinci_gpio_get_pdata(struct platform_device *pdev)
{
struct device_node *dn = pdev->dev.of_node;
struct davinci_gpio_platform_data *pdata;
int ret;
u32 val;
if (!IS_ENABLED(CONFIG_OF) || !pdev->dev.of_node)
return dev_get_platdata(&pdev->dev);
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
return NULL;
ret = of_property_read_u32(dn, "ti,ngpio", &val);
if (ret)
goto of_err;
pdata->ngpio = val;
ret = of_property_read_u32(dn, "ti,davinci-gpio-unbanked", &val);
if (ret)
goto of_err;
pdata->gpio_unbanked = val;
return pdata;
of_err:
dev_err(&pdev->dev, "Populating pdata from DT failed: err %d\n", ret);
return NULL;
}
static int davinci_gpio_probe(struct platform_device *pdev)
{
int bank, i, ret = 0;
unsigned int ngpio, nbank, nirq;
struct davinci_gpio_controller *chips;
struct davinci_gpio_platform_data *pdata;
struct device *dev = &pdev->dev;
pdata = davinci_gpio_get_pdata(pdev);
if (!pdata) {
dev_err(dev, "No platform data found\n");
return -EINVAL;
}
dev->platform_data = pdata;
/*
* The gpio banks conceptually expose a segmented bitmap,
* and "ngpio" is one more than the largest zero-based
* bit index that's valid.
*/
ngpio = pdata->ngpio;
if (ngpio == 0) {
dev_err(dev, "How many GPIOs?\n");
return -EINVAL;
}
if (WARN_ON(ARCH_NR_GPIOS < ngpio))
ngpio = ARCH_NR_GPIOS;
/*
* If there are unbanked interrupts then the number of
* interrupts is equal to number of gpios else all are banked so
* number of interrupts is equal to number of banks(each with 16 gpios)
*/
if (pdata->gpio_unbanked)
nirq = pdata->gpio_unbanked;
else
nirq = DIV_ROUND_UP(ngpio, 16);
chips = devm_kzalloc(dev, sizeof(*chips), GFP_KERNEL);
if (!chips)
return -ENOMEM;
gpio_base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(gpio_base))
return PTR_ERR(gpio_base);
for (i = 0; i < nirq; i++) {
chips->irqs[i] = platform_get_irq(pdev, i);
if (chips->irqs[i] < 0)
return dev_err_probe(dev, chips->irqs[i], "IRQ not populated\n");
}
chips->chip.label = dev_name(dev);
chips->chip.direction_input = davinci_direction_in;
chips->chip.get = davinci_gpio_get;
chips->chip.direction_output = davinci_direction_out;
chips->chip.set = davinci_gpio_set;
chips->chip.ngpio = ngpio;
chips->chip.base = pdata->no_auto_base ? pdata->base : -1;
#ifdef CONFIG_OF_GPIO
chips->chip.of_gpio_n_cells = 2;
chips->chip.parent = dev;
chips->chip.of_node = dev->of_node;
chips->chip.request = gpiochip_generic_request;
chips->chip.free = gpiochip_generic_free;
#endif
spin_lock_init(&chips->lock);
nbank = DIV_ROUND_UP(ngpio, 32);
for (bank = 0; bank < nbank; bank++)
chips->regs[bank] = gpio_base + offset_array[bank];
ret = devm_gpiochip_add_data(dev, &chips->chip, chips);
if (ret)
return ret;
platform_set_drvdata(pdev, chips);
ret = davinci_gpio_irq_setup(pdev);
if (ret)
return ret;
return 0;
}
/*--------------------------------------------------------------------------*/
/*
* We expect irqs will normally be set up as input pins, but they can also be
* used as output pins ... which is convenient for testing.
*
* NOTE: The first few GPIOs also have direct INTC hookups in addition
* to their GPIOBNK0 irq, with a bit less overhead.
*
* All those INTC hookups (direct, plus several IRQ banks) can also
* serve as EDMA event triggers.
*/
static void gpio_irq_disable(struct irq_data *d)
{
struct davinci_gpio_regs __iomem *g = irq2regs(d);
uintptr_t mask = (uintptr_t)irq_data_get_irq_handler_data(d);
writel_relaxed(mask, &g->clr_falling);
writel_relaxed(mask, &g->clr_rising);
}
static void gpio_irq_enable(struct irq_data *d)
{
struct davinci_gpio_regs __iomem *g = irq2regs(d);
uintptr_t mask = (uintptr_t)irq_data_get_irq_handler_data(d);
unsigned status = irqd_get_trigger_type(d);
status &= IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING;
if (!status)
status = IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING;
if (status & IRQ_TYPE_EDGE_FALLING)
writel_relaxed(mask, &g->set_falling);
if (status & IRQ_TYPE_EDGE_RISING)
writel_relaxed(mask, &g->set_rising);
}
static int gpio_irq_type(struct irq_data *d, unsigned trigger)
{
if (trigger & ~(IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
return -EINVAL;
return 0;
}
static struct irq_chip gpio_irqchip = {
.name = "GPIO",
.irq_enable = gpio_irq_enable,
.irq_disable = gpio_irq_disable,
.irq_set_type = gpio_irq_type,
.flags = IRQCHIP_SET_TYPE_MASKED,
};
static void gpio_irq_handler(struct irq_desc *desc)
{
struct davinci_gpio_regs __iomem *g;
u32 mask = 0xffff;
int bank_num;
struct davinci_gpio_controller *d;
struct davinci_gpio_irq_data *irqdata;
irqdata = (struct davinci_gpio_irq_data *)irq_desc_get_handler_data(desc);
bank_num = irqdata->bank_num;
g = irqdata->regs;
d = irqdata->chip;
/* we only care about one bank */
if ((bank_num % 2) == 1)
mask <<= 16;
/* temporarily mask (level sensitive) parent IRQ */
chained_irq_enter(irq_desc_get_chip(desc), desc);
while (1) {
u32 status;
int bit;
irq_hw_number_t hw_irq;
/* ack any irqs */
status = readl_relaxed(&g->intstat) & mask;
if (!status)
break;
writel_relaxed(status, &g->intstat);
/* now demux them to the right lowlevel handler */
while (status) {
bit = __ffs(status);
status &= ~BIT(bit);
/* Max number of gpios per controller is 144 so
* hw_irq will be in [0..143]
*/
hw_irq = (bank_num / 2) * 32 + bit;
generic_handle_irq(
irq_find_mapping(d->irq_domain, hw_irq));
}
}
chained_irq_exit(irq_desc_get_chip(desc), desc);
/* now it may re-trigger */
}
static int gpio_to_irq_banked(struct gpio_chip *chip, unsigned offset)
{
struct davinci_gpio_controller *d = gpiochip_get_data(chip);
if (d->irq_domain)
return irq_create_mapping(d->irq_domain, offset);
else
return -ENXIO;
}
static int gpio_to_irq_unbanked(struct gpio_chip *chip, unsigned offset)
{
struct davinci_gpio_controller *d = gpiochip_get_data(chip);
/*
* NOTE: we assume for now that only irqs in the first gpio_chip
* can provide direct-mapped IRQs to AINTC (up to 32 GPIOs).
*/
if (offset < d->gpio_unbanked)
return d->irqs[offset];
else
return -ENODEV;
}
static int gpio_irq_type_unbanked(struct irq_data *data, unsigned trigger)
{
struct davinci_gpio_controller *d;
struct davinci_gpio_regs __iomem *g;
u32 mask, i;
d = (struct davinci_gpio_controller *)irq_data_get_irq_handler_data(data);
g = (struct davinci_gpio_regs __iomem *)d->regs[0];
for (i = 0; i < MAX_INT_PER_BANK; i++)
if (data->irq == d->irqs[i])
break;
if (i == MAX_INT_PER_BANK)
return -EINVAL;
mask = __gpio_mask(i);
if (trigger & ~(IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
return -EINVAL;
writel_relaxed(mask, (trigger & IRQ_TYPE_EDGE_FALLING)
? &g->set_falling : &g->clr_falling);
writel_relaxed(mask, (trigger & IRQ_TYPE_EDGE_RISING)
? &g->set_rising : &g->clr_rising);
return 0;
}
static int
davinci_gpio_irq_map(struct irq_domain *d, unsigned int irq,
irq_hw_number_t hw)
{
struct davinci_gpio_controller *chips =
(struct davinci_gpio_controller *)d->host_data;
struct davinci_gpio_regs __iomem *g = chips->regs[hw / 32];
irq_set_chip_and_handler_name(irq, &gpio_irqchip, handle_simple_irq,
"davinci_gpio");
irq_set_irq_type(irq, IRQ_TYPE_NONE);
irq_set_chip_data(irq, (__force void *)g);
irq_set_handler_data(irq, (void *)(uintptr_t)__gpio_mask(hw));
return 0;
}
static const struct irq_domain_ops davinci_gpio_irq_ops = {
.map = davinci_gpio_irq_map,
.xlate = irq_domain_xlate_onetwocell,
};
static struct irq_chip *davinci_gpio_get_irq_chip(unsigned int irq)
{
static struct irq_chip_type gpio_unbanked;
gpio_unbanked = *irq_data_get_chip_type(irq_get_irq_data(irq));
return &gpio_unbanked.chip;
};
static struct irq_chip *keystone_gpio_get_irq_chip(unsigned int irq)
{
static struct irq_chip gpio_unbanked;
gpio_unbanked = *irq_get_chip(irq);
return &gpio_unbanked;
};
static const struct of_device_id davinci_gpio_ids[];
/*
* NOTE: for suspend/resume, probably best to make a platform_device with
* suspend_late/resume_resume calls hooking into results of the set_wake()
* calls ... so if no gpios are wakeup events the clock can be disabled,
* with outputs left at previously set levels, and so that VDD3P3V.IOPWDN0
* (dm6446) can be set appropriately for GPIOV33 pins.
*/
static int davinci_gpio_irq_setup(struct platform_device *pdev)
{
unsigned gpio, bank;
int irq;
int ret;
struct clk *clk;
u32 binten = 0;
unsigned ngpio;
struct device *dev = &pdev->dev;
struct davinci_gpio_controller *chips = platform_get_drvdata(pdev);
struct davinci_gpio_platform_data *pdata = dev->platform_data;
struct davinci_gpio_regs __iomem *g;
struct irq_domain *irq_domain = NULL;
const struct of_device_id *match;
struct irq_chip *irq_chip;
struct davinci_gpio_irq_data *irqdata;
gpio_get_irq_chip_cb_t gpio_get_irq_chip;
/*
* Use davinci_gpio_get_irq_chip by default to handle non DT cases
*/
gpio_get_irq_chip = davinci_gpio_get_irq_chip;
match = of_match_device(of_match_ptr(davinci_gpio_ids),
dev);
if (match)
gpio_get_irq_chip = (gpio_get_irq_chip_cb_t)match->data;
ngpio = pdata->ngpio;
clk = devm_clk_get(dev, "gpio");
if (IS_ERR(clk)) {
dev_err(dev, "Error %ld getting gpio clock\n", PTR_ERR(clk));
return PTR_ERR(clk);
}
ret = clk_prepare_enable(clk);
if (ret)
return ret;
if (!pdata->gpio_unbanked) {
irq = devm_irq_alloc_descs(dev, -1, 0, ngpio, 0);
if (irq < 0) {
dev_err(dev, "Couldn't allocate IRQ numbers\n");
clk_disable_unprepare(clk);
return irq;
}
irq_domain = irq_domain_add_legacy(dev->of_node, ngpio, irq, 0,
&davinci_gpio_irq_ops,
chips);
if (!irq_domain) {
dev_err(dev, "Couldn't register an IRQ domain\n");
clk_disable_unprepare(clk);
return -ENODEV;
}
}
/*
* Arrange gpio_to_irq() support, handling either direct IRQs or
* banked IRQs. Having GPIOs in the first GPIO bank use direct
* IRQs, while the others use banked IRQs, would need some setup
* tweaks to recognize hardware which can do that.
*/
chips->chip.to_irq = gpio_to_irq_banked;
chips->irq_domain = irq_domain;
/*
* AINTC can handle direct/unbanked IRQs for GPIOs, with the GPIO
* controller only handling trigger modes. We currently assume no
* IRQ mux conflicts; gpio_irq_type_unbanked() is only for GPIOs.
*/
if (pdata->gpio_unbanked) {
/* pass "bank 0" GPIO IRQs to AINTC */
chips->chip.to_irq = gpio_to_irq_unbanked;
chips->gpio_unbanked = pdata->gpio_unbanked;
binten = GENMASK(pdata->gpio_unbanked / 16, 0);
/* AINTC handles mask/unmask; GPIO handles triggering */
irq = chips->irqs[0];
irq_chip = gpio_get_irq_chip(irq);
irq_chip->name = "GPIO-AINTC";
irq_chip->irq_set_type = gpio_irq_type_unbanked;
/* default trigger: both edges */
g = chips->regs[0];
writel_relaxed(~0, &g->set_falling);
writel_relaxed(~0, &g->set_rising);
/* set the direct IRQs up to use that irqchip */
for (gpio = 0; gpio < pdata->gpio_unbanked; gpio++) {
irq_set_chip(chips->irqs[gpio], irq_chip);
irq_set_handler_data(chips->irqs[gpio], chips);
irq_set_status_flags(chips->irqs[gpio],
IRQ_TYPE_EDGE_BOTH);
}
goto done;
}
/*
* Or, AINTC can handle IRQs for banks of 16 GPIO IRQs, which we
* then chain through our own handler.
*/
for (gpio = 0, bank = 0; gpio < ngpio; bank++, gpio += 16) {
/* disabled by default, enabled only as needed
* There are register sets for 32 GPIOs. 2 banks of 16
* GPIOs are covered by each set of registers hence divide by 2
*/
g = chips->regs[bank / 2];
writel_relaxed(~0, &g->clr_falling);
writel_relaxed(~0, &g->clr_rising);
/*
* Each chip handles 32 gpios, and each irq bank consists of 16
* gpio irqs. Pass the irq bank's corresponding controller to
* the chained irq handler.
*/
irqdata = devm_kzalloc(&pdev->dev,
sizeof(struct
davinci_gpio_irq_data),
GFP_KERNEL);
if (!irqdata) {
clk_disable_unprepare(clk);
return -ENOMEM;
}
irqdata->regs = g;
irqdata->bank_num = bank;
irqdata->chip = chips;
irq_set_chained_handler_and_data(chips->irqs[bank],
gpio_irq_handler, irqdata);
binten |= BIT(bank);
}
done:
/*
* BINTEN -- per-bank interrupt enable. genirq would also let these
* bits be set/cleared dynamically.
*/
writel_relaxed(binten, gpio_base + BINTEN);
return 0;
}
static const struct of_device_id davinci_gpio_ids[] = {
{ .compatible = "ti,keystone-gpio", keystone_gpio_get_irq_chip},
{ .compatible = "ti,am654-gpio", keystone_gpio_get_irq_chip},
{ .compatible = "ti,dm6441-gpio", davinci_gpio_get_irq_chip},
{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, davinci_gpio_ids);
static struct platform_driver davinci_gpio_driver = {
.probe = davinci_gpio_probe,
.driver = {
.name = "davinci_gpio",
.of_match_table = of_match_ptr(davinci_gpio_ids),
},
};
/**
* GPIO driver registration needs to be done before machine_init functions
* access GPIO. Hence davinci_gpio_drv_reg() is a postcore_initcall.
*/
static int __init davinci_gpio_drv_reg(void)
{
return platform_driver_register(&davinci_gpio_driver);
}
postcore_initcall(davinci_gpio_drv_reg);