forked from luck/tmp_suning_uos_patched
2d24b532f9
These changes based on work by Steven King <sfking@fdwdc.com> to support the i2c hardware modules on ColdFire SoC family devices. This is the per SoC hardware support. Contains a common platform device setup. Each of the SoC family members tends to have some minor local setup required to initialize the module. But all ColdFire family members use the same i2c hardware module. This i2c hardware module is the same as used in the Freescale iMX ARM based family of SoC devices. Steven's original patches were based on using a new and different i2c-coldfire.c driver. But this is not neccessary as we can use the existing Linux i2c-imx.c driver with no change required to it. And this patch is now based on using the existing i2c-imx driver. This patch only contains the ColdFire platform changes. Signed-off-by: Greg Ungerer <gerg@uclinux.org> Tested-by: Angelo Dureghello <angelo@sysam.it>
151 lines
3.8 KiB
C
151 lines
3.8 KiB
C
/***************************************************************************/
|
|
|
|
/*
|
|
* m528x.c -- platform support for ColdFire 528x based boards
|
|
*
|
|
* Sub-architcture dependent initialization code for the Freescale
|
|
* 5280, 5281 and 5282 CPUs.
|
|
*
|
|
* Copyright (C) 1999-2003, Greg Ungerer (gerg@snapgear.com)
|
|
* Copyright (C) 2001-2003, SnapGear Inc. (www.snapgear.com)
|
|
*/
|
|
|
|
/***************************************************************************/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/param.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/io.h>
|
|
#include <asm/machdep.h>
|
|
#include <asm/coldfire.h>
|
|
#include <asm/mcfsim.h>
|
|
#include <asm/mcfuart.h>
|
|
#include <asm/mcfclk.h>
|
|
|
|
/***************************************************************************/
|
|
|
|
DEFINE_CLK(pll, "pll.0", MCF_CLK);
|
|
DEFINE_CLK(sys, "sys.0", MCF_BUSCLK);
|
|
DEFINE_CLK(mcfpit0, "mcfpit.0", MCF_CLK);
|
|
DEFINE_CLK(mcfpit1, "mcfpit.1", MCF_CLK);
|
|
DEFINE_CLK(mcfpit2, "mcfpit.2", MCF_CLK);
|
|
DEFINE_CLK(mcfpit3, "mcfpit.3", MCF_CLK);
|
|
DEFINE_CLK(mcfuart0, "mcfuart.0", MCF_BUSCLK);
|
|
DEFINE_CLK(mcfuart1, "mcfuart.1", MCF_BUSCLK);
|
|
DEFINE_CLK(mcfuart2, "mcfuart.2", MCF_BUSCLK);
|
|
DEFINE_CLK(mcfqspi0, "mcfqspi.0", MCF_BUSCLK);
|
|
DEFINE_CLK(fec0, "fec.0", MCF_BUSCLK);
|
|
DEFINE_CLK(mcfi2c0, "imx1-i2c.0", MCF_BUSCLK);
|
|
|
|
struct clk *mcf_clks[] = {
|
|
&clk_pll,
|
|
&clk_sys,
|
|
&clk_mcfpit0,
|
|
&clk_mcfpit1,
|
|
&clk_mcfpit2,
|
|
&clk_mcfpit3,
|
|
&clk_mcfuart0,
|
|
&clk_mcfuart1,
|
|
&clk_mcfuart2,
|
|
&clk_mcfqspi0,
|
|
&clk_fec0,
|
|
&clk_mcfi2c0,
|
|
NULL
|
|
};
|
|
|
|
/***************************************************************************/
|
|
|
|
static void __init m528x_qspi_init(void)
|
|
{
|
|
#if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI)
|
|
/* setup Port QS for QSPI with gpio CS control */
|
|
__raw_writeb(0x07, MCFGPIO_PQSPAR);
|
|
#endif /* IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) */
|
|
}
|
|
|
|
/***************************************************************************/
|
|
|
|
static void __init m528x_i2c_init(void)
|
|
{
|
|
#if IS_ENABLED(CONFIG_I2C_IMX)
|
|
u16 paspar;
|
|
|
|
/* setup Port AS Pin Assignment Register for I2C */
|
|
/* set PASPA0 to SCL and PASPA1 to SDA */
|
|
paspar = readw(MCFGPIO_PASPAR);
|
|
paspar |= 0xF;
|
|
writew(paspar, MCFGPIO_PASPAR);
|
|
#endif /* IS_ENABLED(CONFIG_I2C_IMX) */
|
|
}
|
|
|
|
/***************************************************************************/
|
|
|
|
static void __init m528x_uarts_init(void)
|
|
{
|
|
u8 port;
|
|
|
|
/* make sure PUAPAR is set for UART0 and UART1 */
|
|
port = readb(MCFGPIO_PUAPAR);
|
|
port |= 0x03 | (0x03 << 2);
|
|
writeb(port, MCFGPIO_PUAPAR);
|
|
}
|
|
|
|
/***************************************************************************/
|
|
|
|
static void __init m528x_fec_init(void)
|
|
{
|
|
u16 v16;
|
|
|
|
/* Set multi-function pins to ethernet mode for fec0 */
|
|
v16 = readw(MCFGPIO_PASPAR);
|
|
writew(v16 | 0xf00, MCFGPIO_PASPAR);
|
|
writeb(0xc0, MCFGPIO_PEHLPAR);
|
|
}
|
|
|
|
/***************************************************************************/
|
|
|
|
#ifdef CONFIG_WILDFIRE
|
|
void wildfire_halt(void)
|
|
{
|
|
writeb(0, 0x30000007);
|
|
writeb(0x2, 0x30000007);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_WILDFIREMOD
|
|
void wildfiremod_halt(void)
|
|
{
|
|
printk(KERN_INFO "WildFireMod hibernating...\n");
|
|
|
|
/* Set portE.5 to Digital IO */
|
|
writew(readw(MCFGPIO_PEPAR) & ~(1 << (5 * 2)), MCFGPIO_PEPAR);
|
|
|
|
/* Make portE.5 an output */
|
|
writeb(readb(MCFGPIO_PDDR_E) | (1 << 5), MCFGPIO_PDDR_E);
|
|
|
|
/* Now toggle portE.5 from low to high */
|
|
writeb(readb(MCFGPIO_PODR_E) & ~(1 << 5), MCFGPIO_PODR_E);
|
|
writeb(readb(MCFGPIO_PODR_E) | (1 << 5), MCFGPIO_PODR_E);
|
|
|
|
printk(KERN_EMERG "Failed to hibernate. Halting!\n");
|
|
}
|
|
#endif
|
|
|
|
void __init config_BSP(char *commandp, int size)
|
|
{
|
|
#ifdef CONFIG_WILDFIRE
|
|
mach_halt = wildfire_halt;
|
|
#endif
|
|
#ifdef CONFIG_WILDFIREMOD
|
|
mach_halt = wildfiremod_halt;
|
|
#endif
|
|
mach_sched_init = hw_timer_init;
|
|
m528x_uarts_init();
|
|
m528x_fec_init();
|
|
m528x_qspi_init();
|
|
m528x_i2c_init();
|
|
}
|
|
|
|
/***************************************************************************/
|