kernel_optimize_test/arch/ppc/platforms/spd8xx.h
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

93 lines
2.8 KiB
C

/*
* Speech Design SPD8xxTS board specific definitions
*
* Copyright (c) 2000,2001 Wolfgang Denk (wd@denx.de)
*/
#ifdef __KERNEL__
#ifndef __ASM_SPD8XX_H__
#define __ASM_SPD8XX_H__
#include <linux/config.h>
#include <asm/ppcboot.h>
#ifndef __ASSEMBLY__
#define SPD_IMMR_BASE 0xFFF00000 /* phys. addr of IMMR */
#define SPD_IMAP_SIZE (64 * 1024) /* size of mapped area */
#define IMAP_ADDR SPD_IMMR_BASE /* physical base address of IMMR area */
#define IMAP_SIZE SPD_IMAP_SIZE /* mapped size of IMMR area */
#define PCMCIA_MEM_ADDR ((uint)0xFE100000)
#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
#define IDE0_INTERRUPT 10 /* = IRQ5 */
#define IDE1_INTERRUPT 12 /* = IRQ6 */
#define CPM_INTERRUPT 13 /* = SIU_LEVEL6 (was: SIU_LEVEL2) */
/* override the default number of IDE hardware interfaces */
#define MAX_HWIFS 2
/*
* Definitions for IDE0 Interface
*/
#define IDE0_BASE_OFFSET 0x0000 /* Offset in PCMCIA memory */
#define IDE0_DATA_REG_OFFSET 0x0000
#define IDE0_ERROR_REG_OFFSET 0x0081
#define IDE0_NSECTOR_REG_OFFSET 0x0082
#define IDE0_SECTOR_REG_OFFSET 0x0083
#define IDE0_LCYL_REG_OFFSET 0x0084
#define IDE0_HCYL_REG_OFFSET 0x0085
#define IDE0_SELECT_REG_OFFSET 0x0086
#define IDE0_STATUS_REG_OFFSET 0x0087
#define IDE0_CONTROL_REG_OFFSET 0x0106
#define IDE0_IRQ_REG_OFFSET 0x000A /* not used */
/*
* Definitions for IDE1 Interface
*/
#define IDE1_BASE_OFFSET 0x0C00 /* Offset in PCMCIA memory */
#define IDE1_DATA_REG_OFFSET 0x0000
#define IDE1_ERROR_REG_OFFSET 0x0081
#define IDE1_NSECTOR_REG_OFFSET 0x0082
#define IDE1_SECTOR_REG_OFFSET 0x0083
#define IDE1_LCYL_REG_OFFSET 0x0084
#define IDE1_HCYL_REG_OFFSET 0x0085
#define IDE1_SELECT_REG_OFFSET 0x0086
#define IDE1_STATUS_REG_OFFSET 0x0087
#define IDE1_CONTROL_REG_OFFSET 0x0106
#define IDE1_IRQ_REG_OFFSET 0x000A /* not used */
/* CPM Ethernet through SCCx.
*
* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
*/
#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */
#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
* SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
*/
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002E00)
/* We don't use the 8259.
*/
#define NR_8259_INTS 0
#endif /* !__ASSEMBLY__ */
#endif /* __ASM_SPD8XX_H__ */
#endif /* __KERNEL__ */