AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity
e3280b2a54
kernel_optimize_test/arch/mips/alchemy/devboards/db1550.c
Manuel Lauss c02a505e5a MIPS: Alchemy: DB1xxx: Explicitly set 50MHz clock for I2C/SPI units. 
Add an explicit call to set the desired rate to get the correct
clock routing for the PSC clocks.  It wasn't broken before, but
now it's less affected by bootloader changes.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7554/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-09-22 13:35:47 +02:00

620 lines
16 KiB
C
Raw Blame History

/*
* Alchemy Db1550/Pb1550 board support
*
* (c) 2011 Manuel Lauss <manuel.lauss@googlemail.com>
*/
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/gpio.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/interrupt.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/platform_device.h>
#include <linux/pm.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <asm/bootinfo.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1xxx_eth.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
#include <asm/mach-au1x00/au1xxx_psc.h>
#include <asm/mach-au1x00/au1550_spi.h>
#include <asm/mach-au1x00/au1550nd.h>
#include <asm/mach-db1x00/bcsr.h>
#include <prom.h>
#include "platform.h"
static void __init db1550_hw_setup(void)
{
void __iomem *base;
unsigned long v;
/* complete pin setup: assign GPIO16 to PSC0_SYNC1 (SPI cs# line)
* as well as PSC1_SYNC for AC97 on PB1550.
*/
v = alchemy_rdsys(AU1000_SYS_PINFUNC);
alchemy_wrsys(v | 1 | SYS_PF_PSC1_S1, AU1000_SYS_PINFUNC);
/* reset the AC97 codec now, the reset time in the psc-ac97 driver
* is apparently too short although it's ridiculous as it is.
*/
base = (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR);
__raw_writel(PSC_SEL_CLK_SERCLK | PSC_SEL_PS_AC97MODE,
base + PSC_SEL_OFFSET);
__raw_writel(PSC_CTRL_DISABLE, base + PSC_CTRL_OFFSET);
wmb();
__raw_writel(PSC_AC97RST_RST, base + PSC_AC97RST_OFFSET);
wmb();
}
int __init db1550_board_setup(void)
{
unsigned short whoami;
bcsr_init(DB1550_BCSR_PHYS_ADDR,
DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS);
whoami = bcsr_read(BCSR_WHOAMI); /* PB1550 hexled offset differs */
switch (BCSR_WHOAMI_BOARD(whoami)) {
case BCSR_WHOAMI_PB1550_SDR:
case BCSR_WHOAMI_PB1550_DDR:
bcsr_init(PB1550_BCSR_PHYS_ADDR,
PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
case BCSR_WHOAMI_DB1550:
break;
default:
return -ENODEV;
}
pr_info("Alchemy/AMD %s Board, CPLD Rev %d Board-ID %d " \
"Daughtercard ID %d\n", get_system_type(),
(whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
db1550_hw_setup();
return 0;
}
/*****************************************************************************/
static struct mtd_partition db1550_spiflash_parts[] = {
{
.name = "spi_flash",
.offset = 0,
.size = MTDPART_SIZ_FULL,
},
};
static struct flash_platform_data db1550_spiflash_data = {
.name = "s25fl010",
.parts = db1550_spiflash_parts,
.nr_parts = ARRAY_SIZE(db1550_spiflash_parts),
.type = "m25p10",
};
static struct spi_board_info db1550_spi_devs[] __initdata = {
{
/* TI TMP121AIDBVR temp sensor */
.modalias = "tmp121",
.max_speed_hz = 2400000,
.bus_num = 0,
.chip_select = 0,
.mode = SPI_MODE_0,
},
{
/* Spansion S25FL001D0FMA SPI flash */
.modalias = "m25p80",
.max_speed_hz = 2400000,
.bus_num = 0,
.chip_select = 1,
.mode = SPI_MODE_0,
.platform_data = &db1550_spiflash_data,
},
};
static struct i2c_board_info db1550_i2c_devs[] __initdata = {
{ I2C_BOARD_INFO("24c04", 0x52),}, /* AT24C04-10 I2C eeprom */
{ I2C_BOARD_INFO("ne1619", 0x2d),}, /* adm1025-compat hwmon */
{ I2C_BOARD_INFO("wm8731", 0x1b),}, /* I2S audio codec WM8731 */
};
/**********************************************************************/
static void au1550_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
unsigned int ctrl)
{
struct nand_chip *this = mtd->priv;
unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
ioaddr &= 0xffffff00;
if (ctrl & NAND_CLE) {
ioaddr += MEM_STNAND_CMD;
} else if (ctrl & NAND_ALE) {
ioaddr += MEM_STNAND_ADDR;
} else {
/* assume we want to r/w real data by default */
ioaddr += MEM_STNAND_DATA;
}
this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
if (cmd != NAND_CMD_NONE) {
__raw_writeb(cmd, this->IO_ADDR_W);
wmb();
}
}
static int au1550_nand_device_ready(struct mtd_info *mtd)
{
return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1;
}
static struct mtd_partition db1550_nand_parts[] = {
{
.name = "NAND FS 0",
.offset = 0,
.size = 8 * 1024 * 1024,
},
{
.name = "NAND FS 1",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL
},
};
struct platform_nand_data db1550_nand_platdata = {
.chip = {
.nr_chips = 1,
.chip_offset = 0,
.nr_partitions = ARRAY_SIZE(db1550_nand_parts),
.partitions = db1550_nand_parts,
.chip_delay = 20,
},
.ctrl = {
.dev_ready = au1550_nand_device_ready,
.cmd_ctrl = au1550_nand_cmd_ctrl,
},
};
static struct resource db1550_nand_res[] = {
[0] = {
.start = 0x20000000,
.end = 0x200000ff,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device db1550_nand_dev = {
.name = "gen_nand",
.num_resources = ARRAY_SIZE(db1550_nand_res),
.resource = db1550_nand_res,
.id = -1,
.dev = {
.platform_data = &db1550_nand_platdata,
}
};
static struct au1550nd_platdata pb1550_nand_pd = {
.parts = db1550_nand_parts,
.num_parts = ARRAY_SIZE(db1550_nand_parts),
.devwidth = 0, /* x8 NAND default, needs fixing up */
};
static struct platform_device pb1550_nand_dev = {
.name = "au1550-nand",
.id = -1,
.resource = db1550_nand_res,
.num_resources = ARRAY_SIZE(db1550_nand_res),
.dev = {
.platform_data = &pb1550_nand_pd,
},
};
static void __init pb1550_nand_setup(void)
{
int boot_swapboot = (alchemy_rdsmem(AU1000_MEM_STSTAT) & (0x7 << 1)) |
((bcsr_read(BCSR_STATUS) >> 6) & 0x1);
gpio_direction_input(206); /* de-assert NAND CS# */
switch (boot_swapboot) {
case 0: case 2: case 8: case 0xC: case 0xD:
/* x16 NAND Flash */
pb1550_nand_pd.devwidth = 1;
/* fallthrough */
case 1: case 3: case 9: case 0xE: case 0xF:
/* x8 NAND, already set up */
platform_device_register(&pb1550_nand_dev);
}
}
/**********************************************************************/
static struct resource au1550_psc0_res[] = {
[0] = {
.start = AU1550_PSC0_PHYS_ADDR,
.end = AU1550_PSC0_PHYS_ADDR + 0xfff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AU1550_PSC0_INT,
.end = AU1550_PSC0_INT,
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = AU1550_DSCR_CMD0_PSC0_TX,
.end = AU1550_DSCR_CMD0_PSC0_TX,
.flags = IORESOURCE_DMA,
},
[3] = {
.start = AU1550_DSCR_CMD0_PSC0_RX,
.end = AU1550_DSCR_CMD0_PSC0_RX,
.flags = IORESOURCE_DMA,
},
};
static void db1550_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
{
if (cs)
bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SPISEL);
else
bcsr_mod(BCSR_BOARD, BCSR_BOARD_SPISEL, 0);
}
static struct au1550_spi_info db1550_spi_platdata = {
.mainclk_hz = 48000000, /* PSC0 clock: max. 2.4MHz SPI clk */
.num_chipselect = 2,
.activate_cs = db1550_spi_cs_en,
};
static u64 spi_dmamask = DMA_BIT_MASK(32);
static struct platform_device db1550_spi_dev = {
.dev = {
.dma_mask = &spi_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &db1550_spi_platdata,
},
.name = "au1550-spi",
.id = 0, /* bus number */
.num_resources = ARRAY_SIZE(au1550_psc0_res),
.resource = au1550_psc0_res,
};
/**********************************************************************/
static struct resource au1550_psc1_res[] = {
[0] = {
.start = AU1550_PSC1_PHYS_ADDR,
.end = AU1550_PSC1_PHYS_ADDR + 0xfff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AU1550_PSC1_INT,
.end = AU1550_PSC1_INT,
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = AU1550_DSCR_CMD0_PSC1_TX,
.end = AU1550_DSCR_CMD0_PSC1_TX,
.flags = IORESOURCE_DMA,
},
[3] = {
.start = AU1550_DSCR_CMD0_PSC1_RX,
.end = AU1550_DSCR_CMD0_PSC1_RX,
.flags = IORESOURCE_DMA,
},
};
static struct platform_device db1550_ac97_dev = {
.name = "au1xpsc_ac97",
.id = 1, /* PSC ID */
.num_resources = ARRAY_SIZE(au1550_psc1_res),
.resource = au1550_psc1_res,
};
static struct resource au1550_psc2_res[] = {
[0] = {
.start = AU1550_PSC2_PHYS_ADDR,
.end = AU1550_PSC2_PHYS_ADDR + 0xfff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AU1550_PSC2_INT,
.end = AU1550_PSC2_INT,
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = AU1550_DSCR_CMD0_PSC2_TX,
.end = AU1550_DSCR_CMD0_PSC2_TX,
.flags = IORESOURCE_DMA,
},
[3] = {
.start = AU1550_DSCR_CMD0_PSC2_RX,
.end = AU1550_DSCR_CMD0_PSC2_RX,
.flags = IORESOURCE_DMA,
},
};
static struct platform_device db1550_i2c_dev = {
.name = "au1xpsc_smbus",
.id = 0, /* bus number */
.num_resources = ARRAY_SIZE(au1550_psc2_res),
.resource = au1550_psc2_res,
};
/**********************************************************************/
static struct resource au1550_psc3_res[] = {
[0] = {
.start = AU1550_PSC3_PHYS_ADDR,
.end = AU1550_PSC3_PHYS_ADDR + 0xfff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AU1550_PSC3_INT,
.end = AU1550_PSC3_INT,
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = AU1550_DSCR_CMD0_PSC3_TX,
.end = AU1550_DSCR_CMD0_PSC3_TX,
.flags = IORESOURCE_DMA,
},
[3] = {
.start = AU1550_DSCR_CMD0_PSC3_RX,
.end = AU1550_DSCR_CMD0_PSC3_RX,
.flags = IORESOURCE_DMA,
},
};
static struct platform_device db1550_i2s_dev = {
.name = "au1xpsc_i2s",
.id = 3, /* PSC ID */
.num_resources = ARRAY_SIZE(au1550_psc3_res),
.resource = au1550_psc3_res,
};
/**********************************************************************/
static struct platform_device db1550_stac_dev = {
.name = "ac97-codec",
.id = 1, /* on PSC1 */
};
static struct platform_device db1550_ac97dma_dev = {
.name = "au1xpsc-pcm",
.id = 1, /* on PSC3 */
};
static struct platform_device db1550_i2sdma_dev = {
.name = "au1xpsc-pcm",
.id = 3, /* on PSC3 */
};
static struct platform_device db1550_sndac97_dev = {
.name = "db1550-ac97",
};
static struct platform_device db1550_sndi2s_dev = {
.name = "db1550-i2s",
};
/**********************************************************************/
static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
{
if ((slot < 11) || (slot > 13) || pin == 0)
return -1;
if (slot == 11)
return (pin == 1) ? AU1550_PCI_INTC : 0xff;
if (slot == 12) {
switch (pin) {
case 1: return AU1550_PCI_INTB;
case 2: return AU1550_PCI_INTC;
case 3: return AU1550_PCI_INTD;
case 4: return AU1550_PCI_INTA;
}
}
if (slot == 13) {
switch (pin) {
case 1: return AU1550_PCI_INTA;
case 2: return AU1550_PCI_INTB;
case 3: return AU1550_PCI_INTC;
case 4: return AU1550_PCI_INTD;
}
}
return -1;
}
static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
{
if ((slot < 12) || (slot > 13) || pin == 0)
return -1;
if (slot == 12) {
switch (pin) {
case 1: return AU1500_PCI_INTB;
case 2: return AU1500_PCI_INTC;
case 3: return AU1500_PCI_INTD;
case 4: return AU1500_PCI_INTA;
}
}
if (slot == 13) {
switch (pin) {
case 1: return AU1500_PCI_INTA;
case 2: return AU1500_PCI_INTB;
case 3: return AU1500_PCI_INTC;
case 4: return AU1500_PCI_INTD;
}
}
return -1;
}
static struct resource alchemy_pci_host_res[] = {
[0] = {
.start = AU1500_PCI_PHYS_ADDR,
.end = AU1500_PCI_PHYS_ADDR + 0xfff,
.flags = IORESOURCE_MEM,
},
};
static struct alchemy_pci_platdata db1550_pci_pd = {
.board_map_irq = db1550_map_pci_irq,
};
static struct platform_device db1550_pci_host_dev = {
.dev.platform_data = &db1550_pci_pd,
.name = "alchemy-pci",
.id = 0,
.num_resources = ARRAY_SIZE(alchemy_pci_host_res),
.resource = alchemy_pci_host_res,
};
/**********************************************************************/
static struct platform_device *db1550_devs[] __initdata = {
&db1550_i2c_dev,
&db1550_ac97_dev,
&db1550_spi_dev,
&db1550_i2s_dev,
&db1550_stac_dev,
&db1550_ac97dma_dev,
&db1550_i2sdma_dev,
&db1550_sndac97_dev,
&db1550_sndi2s_dev,
};
/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
int __init db1550_pci_setup(int id)
{
if (id)
db1550_pci_pd.board_map_irq = pb1550_map_pci_irq;
return platform_device_register(&db1550_pci_host_dev);
}
static void __init db1550_devices(void)
{
alchemy_gpio_direction_output(203, 0); /* red led on */
irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_EDGE_BOTH); /* CD0# */
irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_EDGE_BOTH); /* CD1# */
irq_set_irq_type(AU1550_GPIO3_INT, IRQ_TYPE_LEVEL_LOW); /* CARD0# */
irq_set_irq_type(AU1550_GPIO5_INT, IRQ_TYPE_LEVEL_LOW); /* CARD1# */
irq_set_irq_type(AU1550_GPIO21_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG0# */
irq_set_irq_type(AU1550_GPIO22_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG1# */
db1x_register_pcmcia_socket(
AU1000_PCMCIA_ATTR_PHYS_ADDR,
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
AU1000_PCMCIA_MEM_PHYS_ADDR,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
AU1000_PCMCIA_IO_PHYS_ADDR,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
AU1550_GPIO3_INT, AU1550_GPIO0_INT,
/*AU1550_GPIO21_INT*/0, 0, 0);
db1x_register_pcmcia_socket(
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
AU1550_GPIO5_INT, AU1550_GPIO1_INT,
/*AU1550_GPIO22_INT*/0, 0, 1);
platform_device_register(&db1550_nand_dev);
alchemy_gpio_direction_output(202, 0); /* green led on */
}
static void __init pb1550_devices(void)
{
irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_LEVEL_LOW);
irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_LEVEL_LOW);
irq_set_irq_type(AU1550_GPIO201_205_INT, IRQ_TYPE_LEVEL_HIGH);
/* enable both PCMCIA card irqs in the shared line */
alchemy_gpio2_enable_int(201); /* socket 0 card irq */
alchemy_gpio2_enable_int(202); /* socket 1 card irq */
/* Pb1550, like all others, also has statuschange irqs; however they're
* wired up on one of the Au1550's shared GPIO201_205 line, which also
* services the PCMCIA card interrupts. So we ignore statuschange and
* use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
* drivers are used to shared irqs and b) statuschange isn't really use-
* ful anyway.
*/
db1x_register_pcmcia_socket(
AU1000_PCMCIA_ATTR_PHYS_ADDR,
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
AU1000_PCMCIA_MEM_PHYS_ADDR,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
AU1000_PCMCIA_IO_PHYS_ADDR,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
db1x_register_pcmcia_socket(
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
pb1550_nand_setup();
}
int __init db1550_dev_setup(void)
{
int swapped, id;
struct clk *c;
id = (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) != BCSR_WHOAMI_DB1550);
i2c_register_board_info(0, db1550_i2c_devs,
ARRAY_SIZE(db1550_i2c_devs));
spi_register_board_info(db1550_spi_devs,
ARRAY_SIZE(db1550_i2c_devs));
c = clk_get(NULL, "psc0_intclk");
if (!IS_ERR(c)) {
clk_set_rate(c, 50000000);
clk_prepare_enable(c);
clk_put(c);
}
c = clk_get(NULL, "psc2_intclk");
if (!IS_ERR(c)) {
clk_set_rate(c, db1550_spi_platdata.mainclk_hz);
clk_prepare_enable(c);
clk_put(c);
}
/* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */
__raw_writel(PSC_SEL_CLK_SERCLK,
(void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
__raw_writel(PSC_SEL_CLK_SERCLK,
(void __iomem *)KSEG1ADDR(AU1550_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
/* SPI/I2C use internally supplied 50MHz source */
__raw_writel(PSC_SEL_CLK_INTCLK,
(void __iomem *)KSEG1ADDR(AU1550_PSC0_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
__raw_writel(PSC_SEL_CLK_INTCLK,
(void __iomem *)KSEG1ADDR(AU1550_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
id ? pb1550_devices() : db1550_devices();
swapped = bcsr_read(BCSR_STATUS) &
(id ? BCSR_STATUS_PB1550_SWAPBOOT : BCSR_STATUS_DB1000_SWAPBOOT);
db1x_register_norflash(128 << 20, 4, swapped);
return platform_add_devices(db1550_devs, ARRAY_SIZE(db1550_devs));
}
View Git Blame Copy Permalink