forked from luck/tmp_suning_uos_patched
dd14be4c27
There is sometimes a need for the ocores driver to add devices to the bus when installed. i2c_register_board_info can not always be used, because the I2C devices are not known at an early state, they could for instance be connected on a I2C bus on a PCI device which has the Open Cores IP. i2c_new_device can not be used in all cases either since the resulting bus nummer might be unknown. The solution is the pass a list of I2C devices in the platform data to the Open Cores driver. This is useful for MFD drivers. Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
69 lines
1.8 KiB
Plaintext
69 lines
1.8 KiB
Plaintext
Kernel driver i2c-ocores
|
|
|
|
Supported adapters:
|
|
* OpenCores.org I2C controller by Richard Herveille (see datasheet link)
|
|
Datasheet: http://www.opencores.org/projects.cgi/web/i2c/overview
|
|
|
|
Author: Peter Korsgaard <jacmet@sunsite.dk>
|
|
|
|
Description
|
|
-----------
|
|
|
|
i2c-ocores is an i2c bus driver for the OpenCores.org I2C controller
|
|
IP core by Richard Herveille.
|
|
|
|
Usage
|
|
-----
|
|
|
|
i2c-ocores uses the platform bus, so you need to provide a struct
|
|
platform_device with the base address and interrupt number. The
|
|
dev.platform_data of the device should also point to a struct
|
|
ocores_i2c_platform_data (see linux/i2c-ocores.h) describing the
|
|
distance between registers and the input clock speed.
|
|
There is also a possibility to attach a list of i2c_board_info which
|
|
the i2c-ocores driver will add to the bus upon creation.
|
|
|
|
E.G. something like:
|
|
|
|
static struct resource ocores_resources[] = {
|
|
[0] = {
|
|
.start = MYI2C_BASEADDR,
|
|
.end = MYI2C_BASEADDR + 8,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
[1] = {
|
|
.start = MYI2C_IRQ,
|
|
.end = MYI2C_IRQ,
|
|
.flags = IORESOURCE_IRQ,
|
|
},
|
|
};
|
|
|
|
/* optional board info */
|
|
struct i2c_board_info ocores_i2c_board_info[] = {
|
|
{
|
|
I2C_BOARD_INFO("tsc2003", 0x48),
|
|
.platform_data = &tsc2003_platform_data,
|
|
.irq = TSC_IRQ
|
|
},
|
|
{
|
|
I2C_BOARD_INFO("adv7180", 0x42 >> 1),
|
|
.irq = ADV_IRQ
|
|
}
|
|
};
|
|
|
|
static struct ocores_i2c_platform_data myi2c_data = {
|
|
.regstep = 2, /* two bytes between registers */
|
|
.clock_khz = 50000, /* input clock of 50MHz */
|
|
.devices = ocores_i2c_board_info, /* optional table of devices */
|
|
.num_devices = ARRAY_SIZE(ocores_i2c_board_info), /* table size */
|
|
};
|
|
|
|
static struct platform_device myi2c = {
|
|
.name = "ocores-i2c",
|
|
.dev = {
|
|
.platform_data = &myi2c_data,
|
|
},
|
|
.num_resources = ARRAY_SIZE(ocores_resources),
|
|
.resource = ocores_resources,
|
|
};
|