kernel_optimize_test/arch/arm/plat-omap/gpio.c
Felipe Balbi 8156fae26a arm: omap: remove the unused omap_gpio_set_debounce methods
Nobody uses that anymore, so remove and expect drivers to use the gpiolib
implementation.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-05-27 09:12:42 -07:00

2342 lines
59 KiB
C

/*
* linux/arch/arm/plat-omap/gpio.c
*
* Support functions for OMAP GPIO
*
* Copyright (C) 2003-2005 Nokia Corporation
* Written by Juha Yrjölä <juha.yrjola@nokia.com>
*
* Copyright (C) 2009 Texas Instruments
* Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/sysdev.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#include <mach/irqs.h>
#include <mach/gpio.h>
#include <asm/mach/irq.h>
#include <plat/powerdomain.h>
/*
* OMAP1510 GPIO registers
*/
#define OMAP1510_GPIO_BASE 0xfffce000
#define OMAP1510_GPIO_DATA_INPUT 0x00
#define OMAP1510_GPIO_DATA_OUTPUT 0x04
#define OMAP1510_GPIO_DIR_CONTROL 0x08
#define OMAP1510_GPIO_INT_CONTROL 0x0c
#define OMAP1510_GPIO_INT_MASK 0x10
#define OMAP1510_GPIO_INT_STATUS 0x14
#define OMAP1510_GPIO_PIN_CONTROL 0x18
#define OMAP1510_IH_GPIO_BASE 64
/*
* OMAP1610 specific GPIO registers
*/
#define OMAP1610_GPIO1_BASE 0xfffbe400
#define OMAP1610_GPIO2_BASE 0xfffbec00
#define OMAP1610_GPIO3_BASE 0xfffbb400
#define OMAP1610_GPIO4_BASE 0xfffbbc00
#define OMAP1610_GPIO_REVISION 0x0000
#define OMAP1610_GPIO_SYSCONFIG 0x0010
#define OMAP1610_GPIO_SYSSTATUS 0x0014
#define OMAP1610_GPIO_IRQSTATUS1 0x0018
#define OMAP1610_GPIO_IRQENABLE1 0x001c
#define OMAP1610_GPIO_WAKEUPENABLE 0x0028
#define OMAP1610_GPIO_DATAIN 0x002c
#define OMAP1610_GPIO_DATAOUT 0x0030
#define OMAP1610_GPIO_DIRECTION 0x0034
#define OMAP1610_GPIO_EDGE_CTRL1 0x0038
#define OMAP1610_GPIO_EDGE_CTRL2 0x003c
#define OMAP1610_GPIO_CLEAR_IRQENABLE1 0x009c
#define OMAP1610_GPIO_CLEAR_WAKEUPENA 0x00a8
#define OMAP1610_GPIO_CLEAR_DATAOUT 0x00b0
#define OMAP1610_GPIO_SET_IRQENABLE1 0x00dc
#define OMAP1610_GPIO_SET_WAKEUPENA 0x00e8
#define OMAP1610_GPIO_SET_DATAOUT 0x00f0
/*
* OMAP7XX specific GPIO registers
*/
#define OMAP7XX_GPIO1_BASE 0xfffbc000
#define OMAP7XX_GPIO2_BASE 0xfffbc800
#define OMAP7XX_GPIO3_BASE 0xfffbd000
#define OMAP7XX_GPIO4_BASE 0xfffbd800
#define OMAP7XX_GPIO5_BASE 0xfffbe000
#define OMAP7XX_GPIO6_BASE 0xfffbe800
#define OMAP7XX_GPIO_DATA_INPUT 0x00
#define OMAP7XX_GPIO_DATA_OUTPUT 0x04
#define OMAP7XX_GPIO_DIR_CONTROL 0x08
#define OMAP7XX_GPIO_INT_CONTROL 0x0c
#define OMAP7XX_GPIO_INT_MASK 0x10
#define OMAP7XX_GPIO_INT_STATUS 0x14
#define OMAP1_MPUIO_VBASE OMAP1_MPUIO_BASE
/*
* omap24xx specific GPIO registers
*/
#define OMAP242X_GPIO1_BASE 0x48018000
#define OMAP242X_GPIO2_BASE 0x4801a000
#define OMAP242X_GPIO3_BASE 0x4801c000
#define OMAP242X_GPIO4_BASE 0x4801e000
#define OMAP243X_GPIO1_BASE 0x4900C000
#define OMAP243X_GPIO2_BASE 0x4900E000
#define OMAP243X_GPIO3_BASE 0x49010000
#define OMAP243X_GPIO4_BASE 0x49012000
#define OMAP243X_GPIO5_BASE 0x480B6000
#define OMAP24XX_GPIO_REVISION 0x0000
#define OMAP24XX_GPIO_SYSCONFIG 0x0010
#define OMAP24XX_GPIO_SYSSTATUS 0x0014
#define OMAP24XX_GPIO_IRQSTATUS1 0x0018
#define OMAP24XX_GPIO_IRQSTATUS2 0x0028
#define OMAP24XX_GPIO_IRQENABLE2 0x002c
#define OMAP24XX_GPIO_IRQENABLE1 0x001c
#define OMAP24XX_GPIO_WAKE_EN 0x0020
#define OMAP24XX_GPIO_CTRL 0x0030
#define OMAP24XX_GPIO_OE 0x0034
#define OMAP24XX_GPIO_DATAIN 0x0038
#define OMAP24XX_GPIO_DATAOUT 0x003c
#define OMAP24XX_GPIO_LEVELDETECT0 0x0040
#define OMAP24XX_GPIO_LEVELDETECT1 0x0044
#define OMAP24XX_GPIO_RISINGDETECT 0x0048
#define OMAP24XX_GPIO_FALLINGDETECT 0x004c
#define OMAP24XX_GPIO_DEBOUNCE_EN 0x0050
#define OMAP24XX_GPIO_DEBOUNCE_VAL 0x0054
#define OMAP24XX_GPIO_CLEARIRQENABLE1 0x0060
#define OMAP24XX_GPIO_SETIRQENABLE1 0x0064
#define OMAP24XX_GPIO_CLEARWKUENA 0x0080
#define OMAP24XX_GPIO_SETWKUENA 0x0084
#define OMAP24XX_GPIO_CLEARDATAOUT 0x0090
#define OMAP24XX_GPIO_SETDATAOUT 0x0094
#define OMAP4_GPIO_REVISION 0x0000
#define OMAP4_GPIO_SYSCONFIG 0x0010
#define OMAP4_GPIO_EOI 0x0020
#define OMAP4_GPIO_IRQSTATUSRAW0 0x0024
#define OMAP4_GPIO_IRQSTATUSRAW1 0x0028
#define OMAP4_GPIO_IRQSTATUS0 0x002c
#define OMAP4_GPIO_IRQSTATUS1 0x0030
#define OMAP4_GPIO_IRQSTATUSSET0 0x0034
#define OMAP4_GPIO_IRQSTATUSSET1 0x0038
#define OMAP4_GPIO_IRQSTATUSCLR0 0x003c
#define OMAP4_GPIO_IRQSTATUSCLR1 0x0040
#define OMAP4_GPIO_IRQWAKEN0 0x0044
#define OMAP4_GPIO_IRQWAKEN1 0x0048
#define OMAP4_GPIO_SYSSTATUS 0x0114
#define OMAP4_GPIO_IRQENABLE1 0x011c
#define OMAP4_GPIO_WAKE_EN 0x0120
#define OMAP4_GPIO_IRQSTATUS2 0x0128
#define OMAP4_GPIO_IRQENABLE2 0x012c
#define OMAP4_GPIO_CTRL 0x0130
#define OMAP4_GPIO_OE 0x0134
#define OMAP4_GPIO_DATAIN 0x0138
#define OMAP4_GPIO_DATAOUT 0x013c
#define OMAP4_GPIO_LEVELDETECT0 0x0140
#define OMAP4_GPIO_LEVELDETECT1 0x0144
#define OMAP4_GPIO_RISINGDETECT 0x0148
#define OMAP4_GPIO_FALLINGDETECT 0x014c
#define OMAP4_GPIO_DEBOUNCENABLE 0x0150
#define OMAP4_GPIO_DEBOUNCINGTIME 0x0154
#define OMAP4_GPIO_CLEARIRQENABLE1 0x0160
#define OMAP4_GPIO_SETIRQENABLE1 0x0164
#define OMAP4_GPIO_CLEARWKUENA 0x0180
#define OMAP4_GPIO_SETWKUENA 0x0184
#define OMAP4_GPIO_CLEARDATAOUT 0x0190
#define OMAP4_GPIO_SETDATAOUT 0x0194
/*
* omap34xx specific GPIO registers
*/
#define OMAP34XX_GPIO1_BASE 0x48310000
#define OMAP34XX_GPIO2_BASE 0x49050000
#define OMAP34XX_GPIO3_BASE 0x49052000
#define OMAP34XX_GPIO4_BASE 0x49054000
#define OMAP34XX_GPIO5_BASE 0x49056000
#define OMAP34XX_GPIO6_BASE 0x49058000
/*
* OMAP44XX specific GPIO registers
*/
#define OMAP44XX_GPIO1_BASE 0x4a310000
#define OMAP44XX_GPIO2_BASE 0x48055000
#define OMAP44XX_GPIO3_BASE 0x48057000
#define OMAP44XX_GPIO4_BASE 0x48059000
#define OMAP44XX_GPIO5_BASE 0x4805B000
#define OMAP44XX_GPIO6_BASE 0x4805D000
struct gpio_bank {
unsigned long pbase;
void __iomem *base;
u16 irq;
u16 virtual_irq_start;
int method;
#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
u32 suspend_wakeup;
u32 saved_wakeup;
#endif
#ifdef CONFIG_ARCH_OMAP2PLUS
u32 non_wakeup_gpios;
u32 enabled_non_wakeup_gpios;
u32 saved_datain;
u32 saved_fallingdetect;
u32 saved_risingdetect;
#endif
u32 level_mask;
u32 toggle_mask;
spinlock_t lock;
struct gpio_chip chip;
struct clk *dbck;
u32 mod_usage;
u32 dbck_enable_mask;
};
#define METHOD_MPUIO 0
#define METHOD_GPIO_1510 1
#define METHOD_GPIO_1610 2
#define METHOD_GPIO_7XX 3
#define METHOD_GPIO_24XX 5
#define METHOD_GPIO_44XX 6
#ifdef CONFIG_ARCH_OMAP16XX
static struct gpio_bank gpio_bank_1610[5] = {
{ OMAP1_MPUIO_VBASE, NULL, INT_MPUIO, IH_MPUIO_BASE,
METHOD_MPUIO },
{ OMAP1610_GPIO1_BASE, NULL, INT_GPIO_BANK1, IH_GPIO_BASE,
METHOD_GPIO_1610 },
{ OMAP1610_GPIO2_BASE, NULL, INT_1610_GPIO_BANK2, IH_GPIO_BASE + 16,
METHOD_GPIO_1610 },
{ OMAP1610_GPIO3_BASE, NULL, INT_1610_GPIO_BANK3, IH_GPIO_BASE + 32,
METHOD_GPIO_1610 },
{ OMAP1610_GPIO4_BASE, NULL, INT_1610_GPIO_BANK4, IH_GPIO_BASE + 48,
METHOD_GPIO_1610 },
};
#endif
#ifdef CONFIG_ARCH_OMAP15XX
static struct gpio_bank gpio_bank_1510[2] = {
{ OMAP1_MPUIO_VBASE, NULL, INT_MPUIO, IH_MPUIO_BASE,
METHOD_MPUIO },
{ OMAP1510_GPIO_BASE, NULL, INT_GPIO_BANK1, IH_GPIO_BASE,
METHOD_GPIO_1510 }
};
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
static struct gpio_bank gpio_bank_7xx[7] = {
{ OMAP1_MPUIO_VBASE, NULL, INT_7XX_MPUIO, IH_MPUIO_BASE,
METHOD_MPUIO },
{ OMAP7XX_GPIO1_BASE, NULL, INT_7XX_GPIO_BANK1, IH_GPIO_BASE,
METHOD_GPIO_7XX },
{ OMAP7XX_GPIO2_BASE, NULL, INT_7XX_GPIO_BANK2, IH_GPIO_BASE + 32,
METHOD_GPIO_7XX },
{ OMAP7XX_GPIO3_BASE, NULL, INT_7XX_GPIO_BANK3, IH_GPIO_BASE + 64,
METHOD_GPIO_7XX },
{ OMAP7XX_GPIO4_BASE, NULL, INT_7XX_GPIO_BANK4, IH_GPIO_BASE + 96,
METHOD_GPIO_7XX },
{ OMAP7XX_GPIO5_BASE, NULL, INT_7XX_GPIO_BANK5, IH_GPIO_BASE + 128,
METHOD_GPIO_7XX },
{ OMAP7XX_GPIO6_BASE, NULL, INT_7XX_GPIO_BANK6, IH_GPIO_BASE + 160,
METHOD_GPIO_7XX },
};
#endif
#ifdef CONFIG_ARCH_OMAP2
static struct gpio_bank gpio_bank_242x[4] = {
{ OMAP242X_GPIO1_BASE, NULL, INT_24XX_GPIO_BANK1, IH_GPIO_BASE,
METHOD_GPIO_24XX },
{ OMAP242X_GPIO2_BASE, NULL, INT_24XX_GPIO_BANK2, IH_GPIO_BASE + 32,
METHOD_GPIO_24XX },
{ OMAP242X_GPIO3_BASE, NULL, INT_24XX_GPIO_BANK3, IH_GPIO_BASE + 64,
METHOD_GPIO_24XX },
{ OMAP242X_GPIO4_BASE, NULL, INT_24XX_GPIO_BANK4, IH_GPIO_BASE + 96,
METHOD_GPIO_24XX },
};
static struct gpio_bank gpio_bank_243x[5] = {
{ OMAP243X_GPIO1_BASE, NULL, INT_24XX_GPIO_BANK1, IH_GPIO_BASE,
METHOD_GPIO_24XX },
{ OMAP243X_GPIO2_BASE, NULL, INT_24XX_GPIO_BANK2, IH_GPIO_BASE + 32,
METHOD_GPIO_24XX },
{ OMAP243X_GPIO3_BASE, NULL, INT_24XX_GPIO_BANK3, IH_GPIO_BASE + 64,
METHOD_GPIO_24XX },
{ OMAP243X_GPIO4_BASE, NULL, INT_24XX_GPIO_BANK4, IH_GPIO_BASE + 96,
METHOD_GPIO_24XX },
{ OMAP243X_GPIO5_BASE, NULL, INT_24XX_GPIO_BANK5, IH_GPIO_BASE + 128,
METHOD_GPIO_24XX },
};
#endif
#ifdef CONFIG_ARCH_OMAP3
static struct gpio_bank gpio_bank_34xx[6] = {
{ OMAP34XX_GPIO1_BASE, NULL, INT_34XX_GPIO_BANK1, IH_GPIO_BASE,
METHOD_GPIO_24XX },
{ OMAP34XX_GPIO2_BASE, NULL, INT_34XX_GPIO_BANK2, IH_GPIO_BASE + 32,
METHOD_GPIO_24XX },
{ OMAP34XX_GPIO3_BASE, NULL, INT_34XX_GPIO_BANK3, IH_GPIO_BASE + 64,
METHOD_GPIO_24XX },
{ OMAP34XX_GPIO4_BASE, NULL, INT_34XX_GPIO_BANK4, IH_GPIO_BASE + 96,
METHOD_GPIO_24XX },
{ OMAP34XX_GPIO5_BASE, NULL, INT_34XX_GPIO_BANK5, IH_GPIO_BASE + 128,
METHOD_GPIO_24XX },
{ OMAP34XX_GPIO6_BASE, NULL, INT_34XX_GPIO_BANK6, IH_GPIO_BASE + 160,
METHOD_GPIO_24XX },
};
struct omap3_gpio_regs {
u32 sysconfig;
u32 irqenable1;
u32 irqenable2;
u32 wake_en;
u32 ctrl;
u32 oe;
u32 leveldetect0;
u32 leveldetect1;
u32 risingdetect;
u32 fallingdetect;
u32 dataout;
};
static struct omap3_gpio_regs gpio_context[OMAP34XX_NR_GPIOS];
#endif
#ifdef CONFIG_ARCH_OMAP4
static struct gpio_bank gpio_bank_44xx[6] = {
{ OMAP44XX_GPIO1_BASE, NULL, OMAP44XX_IRQ_GPIO1, IH_GPIO_BASE,
METHOD_GPIO_44XX },
{ OMAP44XX_GPIO2_BASE, NULL, OMAP44XX_IRQ_GPIO2, IH_GPIO_BASE + 32,
METHOD_GPIO_44XX },
{ OMAP44XX_GPIO3_BASE, NULL, OMAP44XX_IRQ_GPIO3, IH_GPIO_BASE + 64,
METHOD_GPIO_44XX },
{ OMAP44XX_GPIO4_BASE, NULL, OMAP44XX_IRQ_GPIO4, IH_GPIO_BASE + 96,
METHOD_GPIO_44XX },
{ OMAP44XX_GPIO5_BASE, NULL, OMAP44XX_IRQ_GPIO5, IH_GPIO_BASE + 128,
METHOD_GPIO_44XX },
{ OMAP44XX_GPIO6_BASE, NULL, OMAP44XX_IRQ_GPIO6, IH_GPIO_BASE + 160,
METHOD_GPIO_44XX },
};
#endif
static struct gpio_bank *gpio_bank;
static int gpio_bank_count;
static inline struct gpio_bank *get_gpio_bank(int gpio)
{
if (cpu_is_omap15xx()) {
if (OMAP_GPIO_IS_MPUIO(gpio))
return &gpio_bank[0];
return &gpio_bank[1];
}
if (cpu_is_omap16xx()) {
if (OMAP_GPIO_IS_MPUIO(gpio))
return &gpio_bank[0];
return &gpio_bank[1 + (gpio >> 4)];
}
if (cpu_is_omap7xx()) {
if (OMAP_GPIO_IS_MPUIO(gpio))
return &gpio_bank[0];
return &gpio_bank[1 + (gpio >> 5)];
}
if (cpu_is_omap24xx())
return &gpio_bank[gpio >> 5];
if (cpu_is_omap34xx() || cpu_is_omap44xx())
return &gpio_bank[gpio >> 5];
BUG();
return NULL;
}
static inline int get_gpio_index(int gpio)
{
if (cpu_is_omap7xx())
return gpio & 0x1f;
if (cpu_is_omap24xx())
return gpio & 0x1f;
if (cpu_is_omap34xx() || cpu_is_omap44xx())
return gpio & 0x1f;
return gpio & 0x0f;
}
static inline int gpio_valid(int gpio)
{
if (gpio < 0)
return -1;
if (cpu_class_is_omap1() && OMAP_GPIO_IS_MPUIO(gpio)) {
if (gpio >= OMAP_MAX_GPIO_LINES + 16)
return -1;
return 0;
}
if (cpu_is_omap15xx() && gpio < 16)
return 0;
if ((cpu_is_omap16xx()) && gpio < 64)
return 0;
if (cpu_is_omap7xx() && gpio < 192)
return 0;
if (cpu_is_omap24xx() && gpio < 128)
return 0;
if ((cpu_is_omap34xx() || cpu_is_omap44xx()) && gpio < 192)
return 0;
return -1;
}
static int check_gpio(int gpio)
{
if (unlikely(gpio_valid(gpio) < 0)) {
printk(KERN_ERR "omap-gpio: invalid GPIO %d\n", gpio);
dump_stack();
return -1;
}
return 0;
}
static void _set_gpio_direction(struct gpio_bank *bank, int gpio, int is_input)
{
void __iomem *reg = bank->base;
u32 l;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
case METHOD_MPUIO:
reg += OMAP_MPUIO_IO_CNTL;
break;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_DIR_CONTROL;
break;
#endif
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
reg += OMAP1610_GPIO_DIRECTION;
break;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_DIR_CONTROL;
break;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_OE;
break;
#endif
#if defined(CONFIG_ARCH_OMAP4)
case METHOD_GPIO_44XX:
reg += OMAP4_GPIO_OE;
break;
#endif
default:
WARN_ON(1);
return;
}
l = __raw_readl(reg);
if (is_input)
l |= 1 << gpio;
else
l &= ~(1 << gpio);
__raw_writel(l, reg);
}
static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable)
{
void __iomem *reg = bank->base;
u32 l = 0;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
case METHOD_MPUIO:
reg += OMAP_MPUIO_OUTPUT;
l = __raw_readl(reg);
if (enable)
l |= 1 << gpio;
else
l &= ~(1 << gpio);
break;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_DATA_OUTPUT;
l = __raw_readl(reg);
if (enable)
l |= 1 << gpio;
else
l &= ~(1 << gpio);
break;
#endif
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
if (enable)
reg += OMAP1610_GPIO_SET_DATAOUT;
else
reg += OMAP1610_GPIO_CLEAR_DATAOUT;
l = 1 << gpio;
break;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_DATA_OUTPUT;
l = __raw_readl(reg);
if (enable)
l |= 1 << gpio;
else
l &= ~(1 << gpio);
break;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
if (enable)
reg += OMAP24XX_GPIO_SETDATAOUT;
else
reg += OMAP24XX_GPIO_CLEARDATAOUT;
l = 1 << gpio;
break;
#endif
#ifdef CONFIG_ARCH_OMAP4
case METHOD_GPIO_44XX:
if (enable)
reg += OMAP4_GPIO_SETDATAOUT;
else
reg += OMAP4_GPIO_CLEARDATAOUT;
l = 1 << gpio;
break;
#endif
default:
WARN_ON(1);
return;
}
__raw_writel(l, reg);
}
static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
{
void __iomem *reg;
if (check_gpio(gpio) < 0)
return -EINVAL;
reg = bank->base;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
case METHOD_MPUIO:
reg += OMAP_MPUIO_INPUT_LATCH;
break;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_DATA_INPUT;
break;
#endif
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
reg += OMAP1610_GPIO_DATAIN;
break;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_DATA_INPUT;
break;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_DATAIN;
break;
#endif
#ifdef CONFIG_ARCH_OMAP4
case METHOD_GPIO_44XX:
reg += OMAP4_GPIO_DATAIN;
break;
#endif
default:
return -EINVAL;
}
return (__raw_readl(reg)
& (1 << get_gpio_index(gpio))) != 0;
}
static int _get_gpio_dataout(struct gpio_bank *bank, int gpio)
{
void __iomem *reg;
if (check_gpio(gpio) < 0)
return -EINVAL;
reg = bank->base;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
case METHOD_MPUIO:
reg += OMAP_MPUIO_OUTPUT;
break;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_DATA_OUTPUT;
break;
#endif
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
reg += OMAP1610_GPIO_DATAOUT;
break;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_DATA_OUTPUT;
break;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_DATAOUT;
break;
#endif
#ifdef CONFIG_ARCH_OMAP4
case METHOD_GPIO_44XX:
reg += OMAP4_GPIO_DATAOUT;
break;
#endif
default:
return -EINVAL;
}
return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0;
}
#define MOD_REG_BIT(reg, bit_mask, set) \
do { \
int l = __raw_readl(base + reg); \
if (set) l |= bit_mask; \
else l &= ~bit_mask; \
__raw_writel(l, base + reg); \
} while(0)
/**
* _set_gpio_debounce - low level gpio debounce time
* @bank: the gpio bank we're acting upon
* @gpio: the gpio number on this @gpio
* @debounce: debounce time to use
*
* OMAP's debounce time is in 31us steps so we need
* to convert and round up to the closest unit.
*/
static void _set_gpio_debounce(struct gpio_bank *bank, unsigned gpio,
unsigned debounce)
{
void __iomem *reg = bank->base;
u32 val;
u32 l;
if (debounce < 32)
debounce = 0x01;
else if (debounce > 7936)
debounce = 0xff;
else
debounce = (debounce / 0x1f) - 1;
l = 1 << get_gpio_index(gpio);
if (cpu_is_omap44xx())
reg += OMAP4_GPIO_DEBOUNCINGTIME;
else
reg += OMAP24XX_GPIO_DEBOUNCE_VAL;
__raw_writel(debounce, reg);
reg = bank->base;
if (cpu_is_omap44xx())
reg += OMAP4_GPIO_DEBOUNCENABLE;
else
reg += OMAP24XX_GPIO_DEBOUNCE_EN;
val = __raw_readl(reg);
if (debounce) {
val |= l;
if (cpu_is_omap34xx() || cpu_is_omap44xx())
clk_enable(bank->dbck);
} else {
val &= ~l;
if (cpu_is_omap34xx() || cpu_is_omap44xx())
clk_disable(bank->dbck);
}
__raw_writel(val, reg);
}
#ifdef CONFIG_ARCH_OMAP2PLUS
static inline void set_24xx_gpio_triggering(struct gpio_bank *bank, int gpio,
int trigger)
{
void __iomem *base = bank->base;
u32 gpio_bit = 1 << gpio;
u32 val;
if (cpu_is_omap44xx()) {
MOD_REG_BIT(OMAP4_GPIO_LEVELDETECT0, gpio_bit,
trigger & IRQ_TYPE_LEVEL_LOW);
MOD_REG_BIT(OMAP4_GPIO_LEVELDETECT1, gpio_bit,
trigger & IRQ_TYPE_LEVEL_HIGH);
MOD_REG_BIT(OMAP4_GPIO_RISINGDETECT, gpio_bit,
trigger & IRQ_TYPE_EDGE_RISING);
MOD_REG_BIT(OMAP4_GPIO_FALLINGDETECT, gpio_bit,
trigger & IRQ_TYPE_EDGE_FALLING);
} else {
MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT0, gpio_bit,
trigger & IRQ_TYPE_LEVEL_LOW);
MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT1, gpio_bit,
trigger & IRQ_TYPE_LEVEL_HIGH);
MOD_REG_BIT(OMAP24XX_GPIO_RISINGDETECT, gpio_bit,
trigger & IRQ_TYPE_EDGE_RISING);
MOD_REG_BIT(OMAP24XX_GPIO_FALLINGDETECT, gpio_bit,
trigger & IRQ_TYPE_EDGE_FALLING);
}
if (likely(!(bank->non_wakeup_gpios & gpio_bit))) {
if (cpu_is_omap44xx()) {
if (trigger != 0)
__raw_writel(1 << gpio, bank->base+
OMAP4_GPIO_IRQWAKEN0);
else {
val = __raw_readl(bank->base +
OMAP4_GPIO_IRQWAKEN0);
__raw_writel(val & (~(1 << gpio)), bank->base +
OMAP4_GPIO_IRQWAKEN0);
}
} else {
/*
* GPIO wakeup request can only be generated on edge
* transitions
*/
if (trigger & IRQ_TYPE_EDGE_BOTH)
__raw_writel(1 << gpio, bank->base
+ OMAP24XX_GPIO_SETWKUENA);
else
__raw_writel(1 << gpio, bank->base
+ OMAP24XX_GPIO_CLEARWKUENA);
}
}
/* This part needs to be executed always for OMAP34xx */
if (cpu_is_omap34xx() || (bank->non_wakeup_gpios & gpio_bit)) {
/*
* Log the edge gpio and manually trigger the IRQ
* after resume if the input level changes
* to avoid irq lost during PER RET/OFF mode
* Applies for omap2 non-wakeup gpio and all omap3 gpios
*/
if (trigger & IRQ_TYPE_EDGE_BOTH)
bank->enabled_non_wakeup_gpios |= gpio_bit;
else
bank->enabled_non_wakeup_gpios &= ~gpio_bit;
}
if (cpu_is_omap44xx()) {
bank->level_mask =
__raw_readl(bank->base + OMAP4_GPIO_LEVELDETECT0) |
__raw_readl(bank->base + OMAP4_GPIO_LEVELDETECT1);
} else {
bank->level_mask =
__raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0) |
__raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1);
}
}
#endif
#ifdef CONFIG_ARCH_OMAP1
/*
* This only applies to chips that can't do both rising and falling edge
* detection at once. For all other chips, this function is a noop.
*/
static void _toggle_gpio_edge_triggering(struct gpio_bank *bank, int gpio)
{
void __iomem *reg = bank->base;
u32 l = 0;
switch (bank->method) {
case METHOD_MPUIO:
reg += OMAP_MPUIO_GPIO_INT_EDGE;
break;
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_INT_CONTROL;
break;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_INT_CONTROL;
break;
#endif
default:
return;
}
l = __raw_readl(reg);
if ((l >> gpio) & 1)
l &= ~(1 << gpio);
else
l |= 1 << gpio;
__raw_writel(l, reg);
}
#endif
static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, int trigger)
{
void __iomem *reg = bank->base;
u32 l = 0;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
case METHOD_MPUIO:
reg += OMAP_MPUIO_GPIO_INT_EDGE;
l = __raw_readl(reg);
if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
bank->toggle_mask |= 1 << gpio;
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
goto bad;
break;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_INT_CONTROL;
l = __raw_readl(reg);
if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
bank->toggle_mask |= 1 << gpio;
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
goto bad;
break;
#endif
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
if (gpio & 0x08)
reg += OMAP1610_GPIO_EDGE_CTRL2;
else
reg += OMAP1610_GPIO_EDGE_CTRL1;
gpio &= 0x07;
l = __raw_readl(reg);
l &= ~(3 << (gpio << 1));
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 2 << (gpio << 1);
if (trigger & IRQ_TYPE_EDGE_FALLING)
l |= 1 << (gpio << 1);
if (trigger)
/* Enable wake-up during idle for dynamic tick */
__raw_writel(1 << gpio, bank->base + OMAP1610_GPIO_SET_WAKEUPENA);
else
__raw_writel(1 << gpio, bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA);
break;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_INT_CONTROL;
l = __raw_readl(reg);
if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
bank->toggle_mask |= 1 << gpio;
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
goto bad;
break;
#endif
#ifdef CONFIG_ARCH_OMAP2PLUS
case METHOD_GPIO_24XX:
case METHOD_GPIO_44XX:
set_24xx_gpio_triggering(bank, gpio, trigger);
break;
#endif
default:
goto bad;
}
__raw_writel(l, reg);
return 0;
bad:
return -EINVAL;
}
static int gpio_irq_type(unsigned irq, unsigned type)
{
struct gpio_bank *bank;
unsigned gpio;
int retval;
unsigned long flags;
if (!cpu_class_is_omap2() && irq > IH_MPUIO_BASE)
gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE);
else
gpio = irq - IH_GPIO_BASE;
if (check_gpio(gpio) < 0)
return -EINVAL;
if (type & ~IRQ_TYPE_SENSE_MASK)
return -EINVAL;
/* OMAP1 allows only only edge triggering */
if (!cpu_class_is_omap2()
&& (type & (IRQ_TYPE_LEVEL_LOW|IRQ_TYPE_LEVEL_HIGH)))
return -EINVAL;
bank = get_irq_chip_data(irq);
spin_lock_irqsave(&bank->lock, flags);
retval = _set_gpio_triggering(bank, get_gpio_index(gpio), type);
if (retval == 0) {
irq_desc[irq].status &= ~IRQ_TYPE_SENSE_MASK;
irq_desc[irq].status |= type;
}
spin_unlock_irqrestore(&bank->lock, flags);
if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
__set_irq_handler_unlocked(irq, handle_level_irq);
else if (type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
__set_irq_handler_unlocked(irq, handle_edge_irq);
return retval;
}
static void _clear_gpio_irqbank(struct gpio_bank *bank, int gpio_mask)
{
void __iomem *reg = bank->base;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
case METHOD_MPUIO:
/* MPUIO irqstatus is reset by reading the status register,
* so do nothing here */
return;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_INT_STATUS;
break;
#endif
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
reg += OMAP1610_GPIO_IRQSTATUS1;
break;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_INT_STATUS;
break;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_IRQSTATUS1;
break;
#endif
#if defined(CONFIG_ARCH_OMAP4)
case METHOD_GPIO_44XX:
reg += OMAP4_GPIO_IRQSTATUS0;
break;
#endif
default:
WARN_ON(1);
return;
}
__raw_writel(gpio_mask, reg);
/* Workaround for clearing DSP GPIO interrupts to allow retention */
if (cpu_is_omap24xx() || cpu_is_omap34xx())
reg = bank->base + OMAP24XX_GPIO_IRQSTATUS2;
else if (cpu_is_omap44xx())
reg = bank->base + OMAP4_GPIO_IRQSTATUS1;
if (cpu_is_omap24xx() || cpu_is_omap34xx() || cpu_is_omap44xx()) {
__raw_writel(gpio_mask, reg);
/* Flush posted write for the irq status to avoid spurious interrupts */
__raw_readl(reg);
}
}
static inline void _clear_gpio_irqstatus(struct gpio_bank *bank, int gpio)
{
_clear_gpio_irqbank(bank, 1 << get_gpio_index(gpio));
}
static u32 _get_gpio_irqbank_mask(struct gpio_bank *bank)
{
void __iomem *reg = bank->base;
int inv = 0;
u32 l;
u32 mask;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
case METHOD_MPUIO:
reg += OMAP_MPUIO_GPIO_MASKIT;
mask = 0xffff;
inv = 1;
break;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_INT_MASK;
mask = 0xffff;
inv = 1;
break;
#endif
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
reg += OMAP1610_GPIO_IRQENABLE1;
mask = 0xffff;
break;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_INT_MASK;
mask = 0xffffffff;
inv = 1;
break;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_IRQENABLE1;
mask = 0xffffffff;
break;
#endif
#if defined(CONFIG_ARCH_OMAP4)
case METHOD_GPIO_44XX:
reg += OMAP4_GPIO_IRQSTATUSSET0;
mask = 0xffffffff;
break;
#endif
default:
WARN_ON(1);
return 0;
}
l = __raw_readl(reg);
if (inv)
l = ~l;
l &= mask;
return l;
}
static void _enable_gpio_irqbank(struct gpio_bank *bank, int gpio_mask, int enable)
{
void __iomem *reg = bank->base;
u32 l;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
case METHOD_MPUIO:
reg += OMAP_MPUIO_GPIO_MASKIT;
l = __raw_readl(reg);
if (enable)
l &= ~(gpio_mask);
else
l |= gpio_mask;
break;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_INT_MASK;
l = __raw_readl(reg);
if (enable)
l &= ~(gpio_mask);
else
l |= gpio_mask;
break;
#endif
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
if (enable)
reg += OMAP1610_GPIO_SET_IRQENABLE1;
else
reg += OMAP1610_GPIO_CLEAR_IRQENABLE1;
l = gpio_mask;
break;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_INT_MASK;
l = __raw_readl(reg);
if (enable)
l &= ~(gpio_mask);
else
l |= gpio_mask;
break;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
if (enable)
reg += OMAP24XX_GPIO_SETIRQENABLE1;
else
reg += OMAP24XX_GPIO_CLEARIRQENABLE1;
l = gpio_mask;
break;
#endif
#ifdef CONFIG_ARCH_OMAP4
case METHOD_GPIO_44XX:
if (enable)
reg += OMAP4_GPIO_IRQSTATUSSET0;
else
reg += OMAP4_GPIO_IRQSTATUSCLR0;
l = gpio_mask;
break;
#endif
default:
WARN_ON(1);
return;
}
__raw_writel(l, reg);
}
static inline void _set_gpio_irqenable(struct gpio_bank *bank, int gpio, int enable)
{
_enable_gpio_irqbank(bank, 1 << get_gpio_index(gpio), enable);
}
/*
* Note that ENAWAKEUP needs to be enabled in GPIO_SYSCONFIG register.
* 1510 does not seem to have a wake-up register. If JTAG is connected
* to the target, system will wake up always on GPIO events. While
* system is running all registered GPIO interrupts need to have wake-up
* enabled. When system is suspended, only selected GPIO interrupts need
* to have wake-up enabled.
*/
static int _set_gpio_wakeup(struct gpio_bank *bank, int gpio, int enable)
{
unsigned long uninitialized_var(flags);
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_MPUIO:
case METHOD_GPIO_1610:
spin_lock_irqsave(&bank->lock, flags);
if (enable)
bank->suspend_wakeup |= (1 << gpio);
else
bank->suspend_wakeup &= ~(1 << gpio);
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
#endif
#ifdef CONFIG_ARCH_OMAP2PLUS
case METHOD_GPIO_24XX:
case METHOD_GPIO_44XX:
if (bank->non_wakeup_gpios & (1 << gpio)) {
printk(KERN_ERR "Unable to modify wakeup on "
"non-wakeup GPIO%d\n",
(bank - gpio_bank) * 32 + gpio);
return -EINVAL;
}
spin_lock_irqsave(&bank->lock, flags);
if (enable)
bank->suspend_wakeup |= (1 << gpio);
else
bank->suspend_wakeup &= ~(1 << gpio);
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
#endif
default:
printk(KERN_ERR "Can't enable GPIO wakeup for method %i\n",
bank->method);
return -EINVAL;
}
}
static void _reset_gpio(struct gpio_bank *bank, int gpio)
{
_set_gpio_direction(bank, get_gpio_index(gpio), 1);
_set_gpio_irqenable(bank, gpio, 0);
_clear_gpio_irqstatus(bank, gpio);
_set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE);
}
/* Use disable_irq_wake() and enable_irq_wake() functions from drivers */
static int gpio_wake_enable(unsigned int irq, unsigned int enable)
{
unsigned int gpio = irq - IH_GPIO_BASE;
struct gpio_bank *bank;
int retval;
if (check_gpio(gpio) < 0)
return -ENODEV;
bank = get_irq_chip_data(irq);
retval = _set_gpio_wakeup(bank, get_gpio_index(gpio), enable);
return retval;
}
static int omap_gpio_request(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
unsigned long flags;
spin_lock_irqsave(&bank->lock, flags);
/* Set trigger to none. You need to enable the desired trigger with
* request_irq() or set_irq_type().
*/
_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE);
#ifdef CONFIG_ARCH_OMAP15XX
if (bank->method == METHOD_GPIO_1510) {
void __iomem *reg;
/* Claim the pin for MPU */
reg = bank->base + OMAP1510_GPIO_PIN_CONTROL;
__raw_writel(__raw_readl(reg) | (1 << offset), reg);
}
#endif
if (!cpu_class_is_omap1()) {
if (!bank->mod_usage) {
void __iomem *reg = bank->base;
u32 ctrl;
if (cpu_is_omap24xx() || cpu_is_omap34xx())
reg += OMAP24XX_GPIO_CTRL;
else if (cpu_is_omap44xx())
reg += OMAP4_GPIO_CTRL;
ctrl = __raw_readl(reg);
/* Module is enabled, clocks are not gated */
ctrl &= 0xFFFFFFFE;
__raw_writel(ctrl, reg);
}
bank->mod_usage |= 1 << offset;
}
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
}
static void omap_gpio_free(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
unsigned long flags;
spin_lock_irqsave(&bank->lock, flags);
#ifdef CONFIG_ARCH_OMAP16XX
if (bank->method == METHOD_GPIO_1610) {
/* Disable wake-up during idle for dynamic tick */
void __iomem *reg = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
__raw_writel(1 << offset, reg);
}
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
if (bank->method == METHOD_GPIO_24XX) {
/* Disable wake-up during idle for dynamic tick */
void __iomem *reg = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
__raw_writel(1 << offset, reg);
}
#endif
#ifdef CONFIG_ARCH_OMAP4
if (bank->method == METHOD_GPIO_44XX) {
/* Disable wake-up during idle for dynamic tick */
void __iomem *reg = bank->base + OMAP4_GPIO_IRQWAKEN0;
__raw_writel(1 << offset, reg);
}
#endif
if (!cpu_class_is_omap1()) {
bank->mod_usage &= ~(1 << offset);
if (!bank->mod_usage) {
void __iomem *reg = bank->base;
u32 ctrl;
if (cpu_is_omap24xx() || cpu_is_omap34xx())
reg += OMAP24XX_GPIO_CTRL;
else if (cpu_is_omap44xx())
reg += OMAP4_GPIO_CTRL;
ctrl = __raw_readl(reg);
/* Module is disabled, clocks are gated */
ctrl |= 1;
__raw_writel(ctrl, reg);
}
}
_reset_gpio(bank, bank->chip.base + offset);
spin_unlock_irqrestore(&bank->lock, flags);
}
/*
* We need to unmask the GPIO bank interrupt as soon as possible to
* avoid missing GPIO interrupts for other lines in the bank.
* Then we need to mask-read-clear-unmask the triggered GPIO lines
* in the bank to avoid missing nested interrupts for a GPIO line.
* If we wait to unmask individual GPIO lines in the bank after the
* line's interrupt handler has been run, we may miss some nested
* interrupts.
*/
static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
{
void __iomem *isr_reg = NULL;
u32 isr;
unsigned int gpio_irq, gpio_index;
struct gpio_bank *bank;
u32 retrigger = 0;
int unmasked = 0;
desc->chip->ack(irq);
bank = get_irq_data(irq);
#ifdef CONFIG_ARCH_OMAP1
if (bank->method == METHOD_MPUIO)
isr_reg = bank->base + OMAP_MPUIO_GPIO_INT;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
if (bank->method == METHOD_GPIO_1510)
isr_reg = bank->base + OMAP1510_GPIO_INT_STATUS;
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
if (bank->method == METHOD_GPIO_1610)
isr_reg = bank->base + OMAP1610_GPIO_IRQSTATUS1;
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
if (bank->method == METHOD_GPIO_7XX)
isr_reg = bank->base + OMAP7XX_GPIO_INT_STATUS;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
if (bank->method == METHOD_GPIO_24XX)
isr_reg = bank->base + OMAP24XX_GPIO_IRQSTATUS1;
#endif
#if defined(CONFIG_ARCH_OMAP4)
if (bank->method == METHOD_GPIO_44XX)
isr_reg = bank->base + OMAP4_GPIO_IRQSTATUS0;
#endif
while(1) {
u32 isr_saved, level_mask = 0;
u32 enabled;
enabled = _get_gpio_irqbank_mask(bank);
isr_saved = isr = __raw_readl(isr_reg) & enabled;
if (cpu_is_omap15xx() && (bank->method == METHOD_MPUIO))
isr &= 0x0000ffff;
if (cpu_class_is_omap2()) {
level_mask = bank->level_mask & enabled;
}
/* clear edge sensitive interrupts before handler(s) are
called so that we don't miss any interrupt occurred while
executing them */
_enable_gpio_irqbank(bank, isr_saved & ~level_mask, 0);
_clear_gpio_irqbank(bank, isr_saved & ~level_mask);
_enable_gpio_irqbank(bank, isr_saved & ~level_mask, 1);
/* if there is only edge sensitive GPIO pin interrupts
configured, we could unmask GPIO bank interrupt immediately */
if (!level_mask && !unmasked) {
unmasked = 1;
desc->chip->unmask(irq);
}
isr |= retrigger;
retrigger = 0;
if (!isr)
break;
gpio_irq = bank->virtual_irq_start;
for (; isr != 0; isr >>= 1, gpio_irq++) {
gpio_index = get_gpio_index(irq_to_gpio(gpio_irq));
if (!(isr & 1))
continue;
#ifdef CONFIG_ARCH_OMAP1
/*
* Some chips can't respond to both rising and falling
* at the same time. If this irq was requested with
* both flags, we need to flip the ICR data for the IRQ
* to respond to the IRQ for the opposite direction.
* This will be indicated in the bank toggle_mask.
*/
if (bank->toggle_mask & (1 << gpio_index))
_toggle_gpio_edge_triggering(bank, gpio_index);
#endif
generic_handle_irq(gpio_irq);
}
}
/* if bank has any level sensitive GPIO pin interrupt
configured, we must unmask the bank interrupt only after
handler(s) are executed in order to avoid spurious bank
interrupt */
if (!unmasked)
desc->chip->unmask(irq);
}
static void gpio_irq_shutdown(unsigned int irq)
{
unsigned int gpio = irq - IH_GPIO_BASE;
struct gpio_bank *bank = get_irq_chip_data(irq);
_reset_gpio(bank, gpio);
}
static void gpio_ack_irq(unsigned int irq)
{
unsigned int gpio = irq - IH_GPIO_BASE;
struct gpio_bank *bank = get_irq_chip_data(irq);
_clear_gpio_irqstatus(bank, gpio);
}
static void gpio_mask_irq(unsigned int irq)
{
unsigned int gpio = irq - IH_GPIO_BASE;
struct gpio_bank *bank = get_irq_chip_data(irq);
_set_gpio_irqenable(bank, gpio, 0);
_set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE);
}
static void gpio_unmask_irq(unsigned int irq)
{
unsigned int gpio = irq - IH_GPIO_BASE;
struct gpio_bank *bank = get_irq_chip_data(irq);
unsigned int irq_mask = 1 << get_gpio_index(gpio);
struct irq_desc *desc = irq_to_desc(irq);
u32 trigger = desc->status & IRQ_TYPE_SENSE_MASK;
if (trigger)
_set_gpio_triggering(bank, get_gpio_index(gpio), trigger);
/* For level-triggered GPIOs, the clearing must be done after
* the HW source is cleared, thus after the handler has run */
if (bank->level_mask & irq_mask) {
_set_gpio_irqenable(bank, gpio, 0);
_clear_gpio_irqstatus(bank, gpio);
}
_set_gpio_irqenable(bank, gpio, 1);
}
static struct irq_chip gpio_irq_chip = {
.name = "GPIO",
.shutdown = gpio_irq_shutdown,
.ack = gpio_ack_irq,
.mask = gpio_mask_irq,
.unmask = gpio_unmask_irq,
.set_type = gpio_irq_type,
.set_wake = gpio_wake_enable,
};
/*---------------------------------------------------------------------*/
#ifdef CONFIG_ARCH_OMAP1
/* MPUIO uses the always-on 32k clock */
static void mpuio_ack_irq(unsigned int irq)
{
/* The ISR is reset automatically, so do nothing here. */
}
static void mpuio_mask_irq(unsigned int irq)
{
unsigned int gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE);
struct gpio_bank *bank = get_irq_chip_data(irq);
_set_gpio_irqenable(bank, gpio, 0);
}
static void mpuio_unmask_irq(unsigned int irq)
{
unsigned int gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE);
struct gpio_bank *bank = get_irq_chip_data(irq);
_set_gpio_irqenable(bank, gpio, 1);
}
static struct irq_chip mpuio_irq_chip = {
.name = "MPUIO",
.ack = mpuio_ack_irq,
.mask = mpuio_mask_irq,
.unmask = mpuio_unmask_irq,
.set_type = gpio_irq_type,
#ifdef CONFIG_ARCH_OMAP16XX
/* REVISIT: assuming only 16xx supports MPUIO wake events */
.set_wake = gpio_wake_enable,
#endif
};
#define bank_is_mpuio(bank) ((bank)->method == METHOD_MPUIO)
#ifdef CONFIG_ARCH_OMAP16XX
#include <linux/platform_device.h>
static int omap_mpuio_suspend_noirq(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct gpio_bank *bank = platform_get_drvdata(pdev);
void __iomem *mask_reg = bank->base + OMAP_MPUIO_GPIO_MASKIT;
unsigned long flags;
spin_lock_irqsave(&bank->lock, flags);
bank->saved_wakeup = __raw_readl(mask_reg);
__raw_writel(0xffff & ~bank->suspend_wakeup, mask_reg);
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
}
static int omap_mpuio_resume_noirq(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct gpio_bank *bank = platform_get_drvdata(pdev);
void __iomem *mask_reg = bank->base + OMAP_MPUIO_GPIO_MASKIT;
unsigned long flags;
spin_lock_irqsave(&bank->lock, flags);
__raw_writel(bank->saved_wakeup, mask_reg);
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
}
static const struct dev_pm_ops omap_mpuio_dev_pm_ops = {
.suspend_noirq = omap_mpuio_suspend_noirq,
.resume_noirq = omap_mpuio_resume_noirq,
};
/* use platform_driver for this, now that there's no longer any
* point to sys_device (other than not disturbing old code).
*/
static struct platform_driver omap_mpuio_driver = {
.driver = {
.name = "mpuio",
.pm = &omap_mpuio_dev_pm_ops,
},
};
static struct platform_device omap_mpuio_device = {
.name = "mpuio",
.id = -1,
.dev = {
.driver = &omap_mpuio_driver.driver,
}
/* could list the /proc/iomem resources */
};
static inline void mpuio_init(void)
{
platform_set_drvdata(&omap_mpuio_device, &gpio_bank_1610[0]);
if (platform_driver_register(&omap_mpuio_driver) == 0)
(void) platform_device_register(&omap_mpuio_device);
}
#else
static inline void mpuio_init(void) {}
#endif /* 16xx */
#else
extern struct irq_chip mpuio_irq_chip;
#define bank_is_mpuio(bank) 0
static inline void mpuio_init(void) {}
#endif
/*---------------------------------------------------------------------*/
/* REVISIT these are stupid implementations! replace by ones that
* don't switch on METHOD_* and which mostly avoid spinlocks
*/
static int gpio_input(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank;
unsigned long flags;
bank = container_of(chip, struct gpio_bank, chip);
spin_lock_irqsave(&bank->lock, flags);
_set_gpio_direction(bank, offset, 1);
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
}
static int gpio_is_input(struct gpio_bank *bank, int mask)
{
void __iomem *reg = bank->base;
switch (bank->method) {
case METHOD_MPUIO:
reg += OMAP_MPUIO_IO_CNTL;
break;
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_DIR_CONTROL;
break;
case METHOD_GPIO_1610:
reg += OMAP1610_GPIO_DIRECTION;
break;
case METHOD_GPIO_7XX:
reg += OMAP7XX_GPIO_DIR_CONTROL;
break;
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_OE;
break;
case METHOD_GPIO_44XX:
reg += OMAP4_GPIO_OE;
break;
default:
WARN_ONCE(1, "gpio_is_input: incorrect OMAP GPIO method");
return -EINVAL;
}
return __raw_readl(reg) & mask;
}
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank;
void __iomem *reg;
int gpio;
u32 mask;
gpio = chip->base + offset;
bank = get_gpio_bank(gpio);
reg = bank->base;
mask = 1 << get_gpio_index(gpio);
if (gpio_is_input(bank, mask))
return _get_gpio_datain(bank, gpio);
else
return _get_gpio_dataout(bank, gpio);
}
static int gpio_output(struct gpio_chip *chip, unsigned offset, int value)
{
struct gpio_bank *bank;
unsigned long flags;
bank = container_of(chip, struct gpio_bank, chip);
spin_lock_irqsave(&bank->lock, flags);
_set_gpio_dataout(bank, offset, value);
_set_gpio_direction(bank, offset, 0);
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
}
static int gpio_debounce(struct gpio_chip *chip, unsigned offset,
unsigned debounce)
{
struct gpio_bank *bank;
unsigned long flags;
bank = container_of(chip, struct gpio_bank, chip);
spin_lock_irqsave(&bank->lock, flags);
_set_gpio_debounce(bank, offset, debounce);
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
}
static void gpio_set(struct gpio_chip *chip, unsigned offset, int value)
{
struct gpio_bank *bank;
unsigned long flags;
bank = container_of(chip, struct gpio_bank, chip);
spin_lock_irqsave(&bank->lock, flags);
_set_gpio_dataout(bank, offset, value);
spin_unlock_irqrestore(&bank->lock, flags);
}
static int gpio_2irq(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank;
bank = container_of(chip, struct gpio_bank, chip);
return bank->virtual_irq_start + offset;
}
/*---------------------------------------------------------------------*/
static int initialized;
#if defined(CONFIG_ARCH_OMAP1) || defined(CONFIG_ARCH_OMAP2)
static struct clk * gpio_ick;
#endif
#if defined(CONFIG_ARCH_OMAP2)
static struct clk * gpio_fck;
#endif
#if defined(CONFIG_ARCH_OMAP2430)
static struct clk * gpio5_ick;
static struct clk * gpio5_fck;
#endif
#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
static struct clk *gpio_iclks[OMAP34XX_NR_GPIOS];
#endif
static void __init omap_gpio_show_rev(void)
{
u32 rev;
if (cpu_is_omap16xx())
rev = __raw_readw(gpio_bank[1].base + OMAP1610_GPIO_REVISION);
else if (cpu_is_omap24xx() || cpu_is_omap34xx())
rev = __raw_readl(gpio_bank[0].base + OMAP24XX_GPIO_REVISION);
else if (cpu_is_omap44xx())
rev = __raw_readl(gpio_bank[0].base + OMAP4_GPIO_REVISION);
else
return;
printk(KERN_INFO "OMAP GPIO hardware version %d.%d\n",
(rev >> 4) & 0x0f, rev & 0x0f);
}
/* This lock class tells lockdep that GPIO irqs are in a different
* category than their parents, so it won't report false recursion.
*/
static struct lock_class_key gpio_lock_class;
static int __init _omap_gpio_init(void)
{
int i;
int gpio = 0;
struct gpio_bank *bank;
int bank_size = SZ_8K; /* Module 4KB + L4 4KB except on omap1 */
char clk_name[11];
initialized = 1;
#if defined(CONFIG_ARCH_OMAP1)
if (cpu_is_omap15xx()) {
gpio_ick = clk_get(NULL, "arm_gpio_ck");
if (IS_ERR(gpio_ick))
printk("Could not get arm_gpio_ck\n");
else
clk_enable(gpio_ick);
}
#endif
#if defined(CONFIG_ARCH_OMAP2)
if (cpu_class_is_omap2()) {
gpio_ick = clk_get(NULL, "gpios_ick");
if (IS_ERR(gpio_ick))
printk("Could not get gpios_ick\n");
else
clk_enable(gpio_ick);
gpio_fck = clk_get(NULL, "gpios_fck");
if (IS_ERR(gpio_fck))
printk("Could not get gpios_fck\n");
else
clk_enable(gpio_fck);
/*
* On 2430 & 3430 GPIO 5 uses CORE L4 ICLK
*/
#if defined(CONFIG_ARCH_OMAP2430)
if (cpu_is_omap2430()) {
gpio5_ick = clk_get(NULL, "gpio5_ick");
if (IS_ERR(gpio5_ick))
printk("Could not get gpio5_ick\n");
else
clk_enable(gpio5_ick);
gpio5_fck = clk_get(NULL, "gpio5_fck");
if (IS_ERR(gpio5_fck))
printk("Could not get gpio5_fck\n");
else
clk_enable(gpio5_fck);
}
#endif
}
#endif
#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
if (cpu_is_omap34xx() || cpu_is_omap44xx()) {
for (i = 0; i < OMAP34XX_NR_GPIOS; i++) {
sprintf(clk_name, "gpio%d_ick", i + 1);
gpio_iclks[i] = clk_get(NULL, clk_name);
if (IS_ERR(gpio_iclks[i]))
printk(KERN_ERR "Could not get %s\n", clk_name);
else
clk_enable(gpio_iclks[i]);
}
}
#endif
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap15xx()) {
gpio_bank_count = 2;
gpio_bank = gpio_bank_1510;
bank_size = SZ_2K;
}
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
if (cpu_is_omap16xx()) {
gpio_bank_count = 5;
gpio_bank = gpio_bank_1610;
bank_size = SZ_2K;
}
#endif
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
if (cpu_is_omap7xx()) {
gpio_bank_count = 7;
gpio_bank = gpio_bank_7xx;
bank_size = SZ_2K;
}
#endif
#ifdef CONFIG_ARCH_OMAP2
if (cpu_is_omap242x()) {
gpio_bank_count = 4;
gpio_bank = gpio_bank_242x;
}
if (cpu_is_omap243x()) {
gpio_bank_count = 5;
gpio_bank = gpio_bank_243x;
}
#endif
#ifdef CONFIG_ARCH_OMAP3
if (cpu_is_omap34xx()) {
gpio_bank_count = OMAP34XX_NR_GPIOS;
gpio_bank = gpio_bank_34xx;
}
#endif
#ifdef CONFIG_ARCH_OMAP4
if (cpu_is_omap44xx()) {
gpio_bank_count = OMAP34XX_NR_GPIOS;
gpio_bank = gpio_bank_44xx;
}
#endif
for (i = 0; i < gpio_bank_count; i++) {
int j, gpio_count = 16;
bank = &gpio_bank[i];
spin_lock_init(&bank->lock);
/* Static mapping, never released */
bank->base = ioremap(bank->pbase, bank_size);
if (!bank->base) {
printk(KERN_ERR "Could not ioremap gpio bank%i\n", i);
continue;
}
if (bank_is_mpuio(bank))
__raw_writew(0xffff, bank->base + OMAP_MPUIO_GPIO_MASKIT);
if (cpu_is_omap15xx() && bank->method == METHOD_GPIO_1510) {
__raw_writew(0xffff, bank->base + OMAP1510_GPIO_INT_MASK);
__raw_writew(0x0000, bank->base + OMAP1510_GPIO_INT_STATUS);
}
if (cpu_is_omap16xx() && bank->method == METHOD_GPIO_1610) {
__raw_writew(0x0000, bank->base + OMAP1610_GPIO_IRQENABLE1);
__raw_writew(0xffff, bank->base + OMAP1610_GPIO_IRQSTATUS1);
__raw_writew(0x0014, bank->base + OMAP1610_GPIO_SYSCONFIG);
}
if (cpu_is_omap7xx() && bank->method == METHOD_GPIO_7XX) {
__raw_writel(0xffffffff, bank->base + OMAP7XX_GPIO_INT_MASK);
__raw_writel(0x00000000, bank->base + OMAP7XX_GPIO_INT_STATUS);
gpio_count = 32; /* 7xx has 32-bit GPIOs */
}
#ifdef CONFIG_ARCH_OMAP2PLUS
if ((bank->method == METHOD_GPIO_24XX) ||
(bank->method == METHOD_GPIO_44XX)) {
static const u32 non_wakeup_gpios[] = {
0xe203ffc0, 0x08700040
};
if (cpu_is_omap44xx()) {
__raw_writel(0xffffffff, bank->base +
OMAP4_GPIO_IRQSTATUSCLR0);
__raw_writew(0x0015, bank->base +
OMAP4_GPIO_SYSCONFIG);
__raw_writel(0x00000000, bank->base +
OMAP4_GPIO_DEBOUNCENABLE);
/*
* Initialize interface clock ungated,
* module enabled
*/
__raw_writel(0, bank->base + OMAP4_GPIO_CTRL);
} else {
__raw_writel(0x00000000, bank->base +
OMAP24XX_GPIO_IRQENABLE1);
__raw_writel(0xffffffff, bank->base +
OMAP24XX_GPIO_IRQSTATUS1);
__raw_writew(0x0015, bank->base +
OMAP24XX_GPIO_SYSCONFIG);
__raw_writel(0x00000000, bank->base +
OMAP24XX_GPIO_DEBOUNCE_EN);
/*
* Initialize interface clock ungated,
* module enabled
*/
__raw_writel(0, bank->base +
OMAP24XX_GPIO_CTRL);
}
if (cpu_is_omap24xx() &&
i < ARRAY_SIZE(non_wakeup_gpios))
bank->non_wakeup_gpios = non_wakeup_gpios[i];
gpio_count = 32;
}
#endif
bank->mod_usage = 0;
/* REVISIT eventually switch from OMAP-specific gpio structs
* over to the generic ones
*/
bank->chip.request = omap_gpio_request;
bank->chip.free = omap_gpio_free;
bank->chip.direction_input = gpio_input;
bank->chip.get = gpio_get;
bank->chip.direction_output = gpio_output;
bank->chip.set_debounce = gpio_debounce;
bank->chip.set = gpio_set;
bank->chip.to_irq = gpio_2irq;
if (bank_is_mpuio(bank)) {
bank->chip.label = "mpuio";
#ifdef CONFIG_ARCH_OMAP16XX
bank->chip.dev = &omap_mpuio_device.dev;
#endif
bank->chip.base = OMAP_MPUIO(0);
} else {
bank->chip.label = "gpio";
bank->chip.base = gpio;
gpio += gpio_count;
}
bank->chip.ngpio = gpio_count;
gpiochip_add(&bank->chip);
for (j = bank->virtual_irq_start;
j < bank->virtual_irq_start + gpio_count; j++) {
lockdep_set_class(&irq_desc[j].lock, &gpio_lock_class);
set_irq_chip_data(j, bank);
if (bank_is_mpuio(bank))
set_irq_chip(j, &mpuio_irq_chip);
else
set_irq_chip(j, &gpio_irq_chip);
set_irq_handler(j, handle_simple_irq);
set_irq_flags(j, IRQF_VALID);
}
set_irq_chained_handler(bank->irq, gpio_irq_handler);
set_irq_data(bank->irq, bank);
if (cpu_is_omap34xx() || cpu_is_omap44xx()) {
sprintf(clk_name, "gpio%d_dbck", i + 1);
bank->dbck = clk_get(NULL, clk_name);
if (IS_ERR(bank->dbck))
printk(KERN_ERR "Could not get %s\n", clk_name);
}
}
/* Enable system clock for GPIO module.
* The CAM_CLK_CTRL *is* really the right place. */
if (cpu_is_omap16xx())
omap_writel(omap_readl(ULPD_CAM_CLK_CTRL) | 0x04, ULPD_CAM_CLK_CTRL);
/* Enable autoidle for the OCP interface */
if (cpu_is_omap24xx())
omap_writel(1 << 0, 0x48019010);
if (cpu_is_omap34xx())
omap_writel(1 << 0, 0x48306814);
omap_gpio_show_rev();
return 0;
}
#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
static int omap_gpio_suspend(struct sys_device *dev, pm_message_t mesg)
{
int i;
if (!cpu_class_is_omap2() && !cpu_is_omap16xx())
return 0;
for (i = 0; i < gpio_bank_count; i++) {
struct gpio_bank *bank = &gpio_bank[i];
void __iomem *wake_status;
void __iomem *wake_clear;
void __iomem *wake_set;
unsigned long flags;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
wake_status = bank->base + OMAP1610_GPIO_WAKEUPENABLE;
wake_clear = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
break;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
wake_status = bank->base + OMAP24XX_GPIO_WAKE_EN;
wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA;
break;
#endif
#ifdef CONFIG_ARCH_OMAP4
case METHOD_GPIO_44XX:
wake_status = bank->base + OMAP4_GPIO_IRQWAKEN0;
wake_clear = bank->base + OMAP4_GPIO_IRQWAKEN0;
wake_set = bank->base + OMAP4_GPIO_IRQWAKEN0;
break;
#endif
default:
continue;
}
spin_lock_irqsave(&bank->lock, flags);
bank->saved_wakeup = __raw_readl(wake_status);
__raw_writel(0xffffffff, wake_clear);
__raw_writel(bank->suspend_wakeup, wake_set);
spin_unlock_irqrestore(&bank->lock, flags);
}
return 0;
}
static int omap_gpio_resume(struct sys_device *dev)
{
int i;
if (!cpu_class_is_omap2() && !cpu_is_omap16xx())
return 0;
for (i = 0; i < gpio_bank_count; i++) {
struct gpio_bank *bank = &gpio_bank[i];
void __iomem *wake_clear;
void __iomem *wake_set;
unsigned long flags;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
wake_clear = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
break;
#endif
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA;
break;
#endif
#ifdef CONFIG_ARCH_OMAP4
case METHOD_GPIO_44XX:
wake_clear = bank->base + OMAP4_GPIO_IRQWAKEN0;
wake_set = bank->base + OMAP4_GPIO_IRQWAKEN0;
break;
#endif
default:
continue;
}
spin_lock_irqsave(&bank->lock, flags);
__raw_writel(0xffffffff, wake_clear);
__raw_writel(bank->saved_wakeup, wake_set);
spin_unlock_irqrestore(&bank->lock, flags);
}
return 0;
}
static struct sysdev_class omap_gpio_sysclass = {
.name = "gpio",
.suspend = omap_gpio_suspend,
.resume = omap_gpio_resume,
};
static struct sys_device omap_gpio_device = {
.id = 0,
.cls = &omap_gpio_sysclass,
};
#endif
#ifdef CONFIG_ARCH_OMAP2PLUS
static int workaround_enabled;
void omap2_gpio_prepare_for_idle(int power_state)
{
int i, c = 0;
int min = 0;
if (cpu_is_omap34xx())
min = 1;
for (i = min; i < gpio_bank_count; i++) {
struct gpio_bank *bank = &gpio_bank[i];
u32 l1, l2;
if (bank->dbck_enable_mask)
clk_disable(bank->dbck);
if (power_state > PWRDM_POWER_OFF)
continue;
/* If going to OFF, remove triggering for all
* non-wakeup GPIOs. Otherwise spurious IRQs will be
* generated. See OMAP2420 Errata item 1.101. */
if (!(bank->enabled_non_wakeup_gpios))
continue;
if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
bank->saved_datain = __raw_readl(bank->base +
OMAP24XX_GPIO_DATAIN);
l1 = __raw_readl(bank->base +
OMAP24XX_GPIO_FALLINGDETECT);
l2 = __raw_readl(bank->base +
OMAP24XX_GPIO_RISINGDETECT);
}
if (cpu_is_omap44xx()) {
bank->saved_datain = __raw_readl(bank->base +
OMAP4_GPIO_DATAIN);
l1 = __raw_readl(bank->base +
OMAP4_GPIO_FALLINGDETECT);
l2 = __raw_readl(bank->base +
OMAP4_GPIO_RISINGDETECT);
}
bank->saved_fallingdetect = l1;
bank->saved_risingdetect = l2;
l1 &= ~bank->enabled_non_wakeup_gpios;
l2 &= ~bank->enabled_non_wakeup_gpios;
if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
__raw_writel(l1, bank->base +
OMAP24XX_GPIO_FALLINGDETECT);
__raw_writel(l2, bank->base +
OMAP24XX_GPIO_RISINGDETECT);
}
if (cpu_is_omap44xx()) {
__raw_writel(l1, bank->base + OMAP4_GPIO_FALLINGDETECT);
__raw_writel(l2, bank->base + OMAP4_GPIO_RISINGDETECT);
}
c++;
}
if (!c) {
workaround_enabled = 0;
return;
}
workaround_enabled = 1;
}
void omap2_gpio_resume_after_idle(void)
{
int i;
int min = 0;
if (cpu_is_omap34xx())
min = 1;
for (i = min; i < gpio_bank_count; i++) {
struct gpio_bank *bank = &gpio_bank[i];
u32 l, gen, gen0, gen1;
if (bank->dbck_enable_mask)
clk_enable(bank->dbck);
if (!workaround_enabled)
continue;
if (!(bank->enabled_non_wakeup_gpios))
continue;
if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
__raw_writel(bank->saved_fallingdetect,
bank->base + OMAP24XX_GPIO_FALLINGDETECT);
__raw_writel(bank->saved_risingdetect,
bank->base + OMAP24XX_GPIO_RISINGDETECT);
l = __raw_readl(bank->base + OMAP24XX_GPIO_DATAIN);
}
if (cpu_is_omap44xx()) {
__raw_writel(bank->saved_fallingdetect,
bank->base + OMAP4_GPIO_FALLINGDETECT);
__raw_writel(bank->saved_risingdetect,
bank->base + OMAP4_GPIO_RISINGDETECT);
l = __raw_readl(bank->base + OMAP4_GPIO_DATAIN);
}
/* Check if any of the non-wakeup interrupt GPIOs have changed
* state. If so, generate an IRQ by software. This is
* horribly racy, but it's the best we can do to work around
* this silicon bug. */
l ^= bank->saved_datain;
l &= bank->enabled_non_wakeup_gpios;
/*
* No need to generate IRQs for the rising edge for gpio IRQs
* configured with falling edge only; and vice versa.
*/
gen0 = l & bank->saved_fallingdetect;
gen0 &= bank->saved_datain;
gen1 = l & bank->saved_risingdetect;
gen1 &= ~(bank->saved_datain);
/* FIXME: Consider GPIO IRQs with level detections properly! */
gen = l & (~(bank->saved_fallingdetect) &
~(bank->saved_risingdetect));
/* Consider all GPIO IRQs needed to be updated */
gen |= gen0 | gen1;
if (gen) {
u32 old0, old1;
if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
old0 = __raw_readl(bank->base +
OMAP24XX_GPIO_LEVELDETECT0);
old1 = __raw_readl(bank->base +
OMAP24XX_GPIO_LEVELDETECT1);
__raw_writel(old0 | gen, bank->base +
OMAP24XX_GPIO_LEVELDETECT0);
__raw_writel(old1 | gen, bank->base +
OMAP24XX_GPIO_LEVELDETECT1);
__raw_writel(old0, bank->base +
OMAP24XX_GPIO_LEVELDETECT0);
__raw_writel(old1, bank->base +
OMAP24XX_GPIO_LEVELDETECT1);
}
if (cpu_is_omap44xx()) {
old0 = __raw_readl(bank->base +
OMAP4_GPIO_LEVELDETECT0);
old1 = __raw_readl(bank->base +
OMAP4_GPIO_LEVELDETECT1);
__raw_writel(old0 | l, bank->base +
OMAP4_GPIO_LEVELDETECT0);
__raw_writel(old1 | l, bank->base +
OMAP4_GPIO_LEVELDETECT1);
__raw_writel(old0, bank->base +
OMAP4_GPIO_LEVELDETECT0);
__raw_writel(old1, bank->base +
OMAP4_GPIO_LEVELDETECT1);
}
}
}
}
#endif
#ifdef CONFIG_ARCH_OMAP3
/* save the registers of bank 2-6 */
void omap_gpio_save_context(void)
{
int i;
/* saving banks from 2-6 only since GPIO1 is in WKUP */
for (i = 1; i < gpio_bank_count; i++) {
struct gpio_bank *bank = &gpio_bank[i];
gpio_context[i].sysconfig =
__raw_readl(bank->base + OMAP24XX_GPIO_SYSCONFIG);
gpio_context[i].irqenable1 =
__raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE1);
gpio_context[i].irqenable2 =
__raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE2);
gpio_context[i].wake_en =
__raw_readl(bank->base + OMAP24XX_GPIO_WAKE_EN);
gpio_context[i].ctrl =
__raw_readl(bank->base + OMAP24XX_GPIO_CTRL);
gpio_context[i].oe =
__raw_readl(bank->base + OMAP24XX_GPIO_OE);
gpio_context[i].leveldetect0 =
__raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0);
gpio_context[i].leveldetect1 =
__raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1);
gpio_context[i].risingdetect =
__raw_readl(bank->base + OMAP24XX_GPIO_RISINGDETECT);
gpio_context[i].fallingdetect =
__raw_readl(bank->base + OMAP24XX_GPIO_FALLINGDETECT);
gpio_context[i].dataout =
__raw_readl(bank->base + OMAP24XX_GPIO_DATAOUT);
}
}
/* restore the required registers of bank 2-6 */
void omap_gpio_restore_context(void)
{
int i;
for (i = 1; i < gpio_bank_count; i++) {
struct gpio_bank *bank = &gpio_bank[i];
__raw_writel(gpio_context[i].sysconfig,
bank->base + OMAP24XX_GPIO_SYSCONFIG);
__raw_writel(gpio_context[i].irqenable1,
bank->base + OMAP24XX_GPIO_IRQENABLE1);
__raw_writel(gpio_context[i].irqenable2,
bank->base + OMAP24XX_GPIO_IRQENABLE2);
__raw_writel(gpio_context[i].wake_en,
bank->base + OMAP24XX_GPIO_WAKE_EN);
__raw_writel(gpio_context[i].ctrl,
bank->base + OMAP24XX_GPIO_CTRL);
__raw_writel(gpio_context[i].oe,
bank->base + OMAP24XX_GPIO_OE);
__raw_writel(gpio_context[i].leveldetect0,
bank->base + OMAP24XX_GPIO_LEVELDETECT0);
__raw_writel(gpio_context[i].leveldetect1,
bank->base + OMAP24XX_GPIO_LEVELDETECT1);
__raw_writel(gpio_context[i].risingdetect,
bank->base + OMAP24XX_GPIO_RISINGDETECT);
__raw_writel(gpio_context[i].fallingdetect,
bank->base + OMAP24XX_GPIO_FALLINGDETECT);
__raw_writel(gpio_context[i].dataout,
bank->base + OMAP24XX_GPIO_DATAOUT);
}
}
#endif
/*
* This may get called early from board specific init
* for boards that have interrupts routed via FPGA.
*/
int __init omap_gpio_init(void)
{
if (!initialized)
return _omap_gpio_init();
else
return 0;
}
static int __init omap_gpio_sysinit(void)
{
int ret = 0;
if (!initialized)
ret = _omap_gpio_init();
mpuio_init();
#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
if (cpu_is_omap16xx() || cpu_class_is_omap2()) {
if (ret == 0) {
ret = sysdev_class_register(&omap_gpio_sysclass);
if (ret == 0)
ret = sysdev_register(&omap_gpio_device);
}
}
#endif
return ret;
}
arch_initcall(omap_gpio_sysinit);