ARM: OMAP: move plat-omap/include/plat/sdrc.h into mach-omap2/sdrc.h

Remove arch/arm/plat-omap/include/plat/sdrc.h by folding its contents
into arch/arm/mach-omap2/sdrc.h.  The objective is to assist Tony in
cleaning out arch/arm/plat-omap/, as his upstreams request.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[tony@atomide.com: updated to remove rotate macros]
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/mach-omap2/board-omap3logic.c

@@ -36,7 +36,6 @@
 
 #include "gpmc-smsc911x.h"
 #include <plat/gpmc.h>
-#include <plat/sdrc.h>
 #include <plat/usb.h>
 
 #include "common.h"

arch/arm/mach-omap2/clkt2xxx_dpllcore.c

@@ -27,13 +27,13 @@
 
 #include <plat/clock.h>
 #include <plat/sram.h>
-#include <plat/sdrc.h>
 
 #include "clock.h"
 #include "clock2xxx.h"
 #include "opp2xxx.h"
 #include "cm2xxx_3xxx.h"
 #include "cm-regbits-24xx.h"
+#include "sdrc.h"
 
 /* #define DOWN_VARIABLE_DPLL 1 */		/* Experimental */
 

arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c

@@ -35,7 +35,6 @@
 
 #include <plat/clock.h>
 #include <plat/sram.h>
-#include <plat/sdrc.h>
 
 #include "soc.h"
 #include "clock.h"
@@ -43,6 +42,7 @@
 #include "opp2xxx.h"
 #include "cm2xxx_3xxx.h"
 #include "cm-regbits-24xx.h"
+#include "sdrc.h"
 
 const struct prcm_config *curr_prcm_set;
 const struct prcm_config *rate_table;

arch/arm/mach-omap2/clkt34xx_dpll3m2.c

@@ -23,7 +23,6 @@
 
 #include <plat/clock.h>
 #include <plat/sram.h>
-#include <plat/sdrc.h>
 
 #include "clock.h"
 #include "clock3xxx.h"

arch/arm/mach-omap2/control.c

@@ -1,7 +1,7 @@
 /*
  * OMAP2/3 System Control Module register access
  *
- * Copyright (C) 2007 Texas Instruments, Inc.
+ * Copyright (C) 2007, 2012 Texas Instruments, Inc.
  * Copyright (C) 2007 Nokia Corporation
  *
  * Written by Paul Walmsley
@@ -15,8 +15,6 @@
 #include <linux/kernel.h>
 #include <linux/io.h>
 
-#include <plat/sdrc.h>
-
 #include "soc.h"
 #include "iomap.h"
 #include "common.h"

arch/arm/mach-omap2/gpmc.c

@@ -31,7 +31,6 @@
 
 #include <plat/cpu.h>
 #include <plat/gpmc.h>
-#include <plat/sdrc.h>
 #include <plat/omap_device.h>
 
 #include "soc.h"

arch/arm/mach-omap2/io.c

@@ -26,7 +26,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/sram.h>
-#include <plat/sdrc.h>
 #include <plat/serial.h>
 #include <plat/omap-pm.h>
 #include <plat/omap_hwmod.h>
@@ -43,6 +42,7 @@
 #include "clock2xxx.h"
 #include "clock3xxx.h"
 #include "clock44xx.h"
+#include "sdrc.h"
 
 /*
  * The machine specific code may provide the extra mapping besides the

arch/arm/mach-omap2/pm34xx.c

@@ -38,7 +38,6 @@
 #include <plat/sram.h>
 #include "clockdomain.h"
 #include "powerdomain.h"
-#include <plat/sdrc.h>
 #include <plat/prcm.h>
 #include <plat/gpmc.h>
 #include <plat/dma.h>

arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h

@@ -11,7 +11,7 @@
 #ifndef __ARCH_ARM_MACH_OMAP2_SDRAM_HYNIX_H8MBX00U0MER0EM
 #define __ARCH_ARM_MACH_OMAP2_SDRAM_HYNIX_H8MBX00U0MER0EM
 
-#include <plat/sdrc.h>
+#include "sdrc.h"
 
 /* Hynix H8MBX00U0MER-0EM */
 static struct omap_sdrc_params h8mbx00u0mer0em_sdrc_params[] = {

arch/arm/mach-omap2/sdram-micron-mt46h32m32lf-6.h

@@ -14,7 +14,7 @@
 #ifndef ARCH_ARM_MACH_OMAP2_SDRAM_MICRON_MT46H32M32LF
 #define ARCH_ARM_MACH_OMAP2_SDRAM_MICRON_MT46H32M32LF
 
-#include <plat/sdrc.h>
+#include "sdrc.h"
 
 /* Micron MT46H32M32LF-6 */
 /* XXX Using ARE = 0x1 (no autorefresh burst) -- can this be changed? */

arch/arm/mach-omap2/sdram-nokia.c

@@ -19,9 +19,9 @@
 
 #include "common.h"
 #include <plat/clock.h>
-#include <plat/sdrc.h>
 
 #include "sdram-nokia.h"
+#include "sdrc.h"
 
 /* In picoseconds, except for tREF (ns), tXP, tCKE, tWTR (clks) */
 struct sdram_timings {

arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h

@@ -11,7 +11,7 @@
 #ifndef __ARCH_ARM_MACH_OMAP2_SDRAM_NUMONYX_M65KXXXXAM
 #define __ARCH_ARM_MACH_OMAP2_SDRAM_NUMONYX_M65KXXXXAM
 
-#include <plat/sdrc.h>
+#include "sdrc.h"
 
 /* Numonyx  M65KXXXXAM */
 static struct omap_sdrc_params m65kxxxxam_sdrc_params[] = {

arch/arm/mach-omap2/sdram-qimonda-hyb18m512160af-6.h

@@ -14,7 +14,7 @@
 #ifndef ARCH_ARM_MACH_OMAP2_SDRAM_QIMONDA_HYB18M512160AF6
 #define ARCH_ARM_MACH_OMAP2_SDRAM_QIMONDA_HYB18M512160AF6
 
-#include <plat/sdrc.h>
+#include "sdrc.h"
 
 /* Qimonda HYB18M512160AF-6 */
 static struct omap_sdrc_params hyb18m512160af6_sdrc_params[] = {

arch/arm/mach-omap2/sdrc.c

@@ -27,7 +27,6 @@
 #include <plat/clock.h>
 #include <plat/sram.h>
 
-#include <plat/sdrc.h>
 #include "sdrc.h"
 
 static struct omap_sdrc_params *sdrc_init_params_cs0, *sdrc_init_params_cs1;

arch/arm/mach-omap2/sdrc.h

@@ -2,12 +2,14 @@
 #define __ARCH_ARM_MACH_OMAP2_SDRC_H
 
 /*
- * OMAP2 SDRC register definitions
+ * OMAP2/3 SDRC/SMS macros and prototypes
  *
- * Copyright (C) 2007 Texas Instruments, Inc.
+ * Copyright (C) 2007-2008, 2012 Texas Instruments, Inc.
- * Copyright (C) 2007 Nokia Corporation
+ * Copyright (C) 2007-2008 Nokia Corporation
  *
- * Written by Paul Walmsley
+ * Paul Walmsley
+ * Tony Lindgren
+ * Richard Woodruff
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -15,8 +17,6 @@
  */
 #undef DEBUG
 
-#include <plat/sdrc.h>
-
 #ifndef __ASSEMBLER__
 
 #include <linux/io.h>
@@ -50,6 +50,58 @@ static inline u32 sms_read_reg(u16 reg)
 {
 	return __raw_readl(OMAP_SMS_REGADDR(reg));
 }
+
+
+/**
+ * struct omap_sdrc_params - SDRC parameters for a given SDRC clock rate
+ * @rate: SDRC clock rate (in Hz)
+ * @actim_ctrla: Value to program to SDRC_ACTIM_CTRLA for this rate
+ * @actim_ctrlb: Value to program to SDRC_ACTIM_CTRLB for this rate
+ * @rfr_ctrl: Value to program to SDRC_RFR_CTRL for this rate
+ * @mr: Value to program to SDRC_MR for this rate
+ *
+ * This structure holds a pre-computed set of register values for the
+ * SDRC for a given SDRC clock rate and SDRAM chip.  These are
+ * intended to be pre-computed and specified in an array in the board-*.c
+ * files.  The structure is keyed off the 'rate' field.
+ */
+struct omap_sdrc_params {
+	unsigned long rate;
+	u32 actim_ctrla;
+	u32 actim_ctrlb;
+	u32 rfr_ctrl;
+	u32 mr;
+};
+
+#ifdef CONFIG_SOC_HAS_OMAP2_SDRC
+void omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
+			    struct omap_sdrc_params *sdrc_cs1);
+#else
+static inline void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
+					  struct omap_sdrc_params *sdrc_cs1) {};
+#endif
+
+int omap2_sdrc_get_params(unsigned long r,
+			  struct omap_sdrc_params **sdrc_cs0,
+			  struct omap_sdrc_params **sdrc_cs1);
+void omap2_sms_save_context(void);
+void omap2_sms_restore_context(void);
+
+struct memory_timings {
+	u32 m_type;		/* ddr = 1, sdr = 0 */
+	u32 dll_mode;		/* use lock mode = 1, unlock mode = 0 */
+	u32 slow_dll_ctrl;	/* unlock mode, dll value for slow speed */
+	u32 fast_dll_ctrl;	/* unlock mode, dll value for fast speed */
+	u32 base_cs;		/* base chip select to use for calculations */
+};
+
+extern void omap2xxx_sdrc_init_params(u32 force_lock_to_unlock_mode);
+struct omap_sdrc_params *rx51_get_sdram_timings(void);
+
+u32 omap2xxx_sdrc_dll_is_unlocked(void);
+u32 omap2xxx_sdrc_reprogram(u32 level, u32 force);
+
+
 #else
 #define OMAP242X_SDRC_REGADDR(reg)					\
 			OMAP2_L3_IO_ADDRESS(OMAP2420_SDRC_BASE + (reg))
@@ -57,6 +109,7 @@ static inline u32 sms_read_reg(u16 reg)
 			OMAP2_L3_IO_ADDRESS(OMAP243X_SDRC_BASE + (reg))
 #define OMAP34XX_SDRC_REGADDR(reg)					\
 			OMAP2_L3_IO_ADDRESS(OMAP343X_SDRC_BASE + (reg))
+
 #endif	/* __ASSEMBLER__ */
 
 /* Minimum frequency that the SDRC DLL can lock at */
@@ -74,4 +127,85 @@ static inline u32 sms_read_reg(u16 reg)
  */
 #define SDRC_MPURATE_LOOPS		96
 
+/* SDRC register offsets - read/write with sdrc_{read,write}_reg() */
+
+#define SDRC_SYSCONFIG		0x010
+#define SDRC_CS_CFG		0x040
+#define SDRC_SHARING		0x044
+#define SDRC_ERR_TYPE		0x04C
+#define SDRC_DLLA_CTRL		0x060
+#define SDRC_DLLA_STATUS	0x064
+#define SDRC_DLLB_CTRL		0x068
+#define SDRC_DLLB_STATUS	0x06C
+#define SDRC_POWER		0x070
+#define SDRC_MCFG_0		0x080
+#define SDRC_MR_0		0x084
+#define SDRC_EMR2_0		0x08c
+#define SDRC_ACTIM_CTRL_A_0	0x09c
+#define SDRC_ACTIM_CTRL_B_0	0x0a0
+#define SDRC_RFR_CTRL_0		0x0a4
+#define SDRC_MANUAL_0		0x0a8
+#define SDRC_MCFG_1		0x0B0
+#define SDRC_MR_1		0x0B4
+#define SDRC_EMR2_1		0x0BC
+#define SDRC_ACTIM_CTRL_A_1	0x0C4
+#define SDRC_ACTIM_CTRL_B_1	0x0C8
+#define SDRC_RFR_CTRL_1		0x0D4
+#define SDRC_MANUAL_1		0x0D8
+
+#define SDRC_POWER_AUTOCOUNT_SHIFT	8
+#define SDRC_POWER_AUTOCOUNT_MASK	(0xffff << SDRC_POWER_AUTOCOUNT_SHIFT)
+#define SDRC_POWER_CLKCTRL_SHIFT	4
+#define SDRC_POWER_CLKCTRL_MASK		(0x3 << SDRC_POWER_CLKCTRL_SHIFT)
+#define SDRC_SELF_REFRESH_ON_AUTOCOUNT	(0x2 << SDRC_POWER_CLKCTRL_SHIFT)
+
+/*
+ * These values represent the number of memory clock cycles between
+ * autorefresh initiation.  They assume 1 refresh per 64 ms (JEDEC), 8192
+ * rows per device, and include a subtraction of a 50 cycle window in the
+ * event that the autorefresh command is delayed due to other SDRC activity.
+ * The '| 1' sets the ARE field to send one autorefresh when the autorefresh
+ * counter reaches 0.
+ *
+ * These represent optimal values for common parts, it won't work for all.
+ * As long as you scale down, most parameters are still work, they just
+ * become sub-optimal. The RFR value goes in the opposite direction. If you
+ * don't adjust it down as your clock period increases the refresh interval
+ * will not be met. Setting all parameters for complete worst case may work,
+ * but may cut memory performance by 2x. Due to errata the DLLs need to be
+ * unlocked and their value needs run time calibration.	A dynamic call is
+ * need for that as no single right value exists acorss production samples.
+ *
+ * Only the FULL speed values are given. Current code is such that rate
+ * changes must be made at DPLLoutx2. The actual value adjustment for low
+ * frequency operation will be handled by omap_set_performance()
+ *
+ * By having the boot loader boot up in the fastest L4 speed available likely
+ * will result in something which you can switch between.
+ */
+#define SDRC_RFR_CTRL_165MHz	(0x00044c00 | 1)
+#define SDRC_RFR_CTRL_133MHz	(0x0003de00 | 1)
+#define SDRC_RFR_CTRL_100MHz	(0x0002da01 | 1)
+#define SDRC_RFR_CTRL_110MHz	(0x0002da01 | 1) /* Need to calc */
+#define SDRC_RFR_CTRL_BYPASS	(0x00005000 | 1) /* Need to calc */
+
+
+/*
+ * SMS register access
+ */
+
+#define OMAP242X_SMS_REGADDR(reg)					\
+		(void __iomem *)OMAP2_L3_IO_ADDRESS(OMAP2420_SMS_BASE + reg)
+#define OMAP243X_SMS_REGADDR(reg)					\
+		(void __iomem *)OMAP2_L3_IO_ADDRESS(OMAP243X_SMS_BASE + reg)
+#define OMAP343X_SMS_REGADDR(reg)					\
+		(void __iomem *)OMAP2_L3_IO_ADDRESS(OMAP343X_SMS_BASE + reg)
+
+/* SMS register offsets - read/write with sms_{read,write}_reg() */
+
+#define SMS_SYSCONFIG			0x010
+/* REVISIT: fill in other SMS registers here */
+
+
+
 #endif

arch/arm/mach-omap2/sdrc2xxx.c

@@ -26,7 +26,6 @@
 
 #include <plat/clock.h>
 #include <plat/sram.h>
-#include <plat/sdrc.h>
 
 #include "soc.h"
 #include "iomap.h"

arch/arm/plat-omap/include/plat/sdrc.h

@@ -1,157 +0,0 @@
-#ifndef ____ASM_ARCH_SDRC_H
-#define ____ASM_ARCH_SDRC_H
-
-/*
- * OMAP2/3 SDRC/SMS register definitions
- *
- * Copyright (C) 2007-2008 Texas Instruments, Inc.
- * Copyright (C) 2007-2008 Nokia Corporation
- *
- * Tony Lindgren
- * Paul Walmsley
- * Richard Woodruff
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-
-/* SDRC register offsets - read/write with sdrc_{read,write}_reg() */
-
-#define SDRC_SYSCONFIG		0x010
-#define SDRC_CS_CFG		0x040
-#define SDRC_SHARING		0x044
-#define SDRC_ERR_TYPE		0x04C
-#define SDRC_DLLA_CTRL		0x060
-#define SDRC_DLLA_STATUS	0x064
-#define SDRC_DLLB_CTRL		0x068
-#define SDRC_DLLB_STATUS	0x06C
-#define SDRC_POWER		0x070
-#define SDRC_MCFG_0		0x080
-#define SDRC_MR_0		0x084
-#define SDRC_EMR2_0		0x08c
-#define SDRC_ACTIM_CTRL_A_0	0x09c
-#define SDRC_ACTIM_CTRL_B_0	0x0a0
-#define SDRC_RFR_CTRL_0		0x0a4
-#define SDRC_MANUAL_0		0x0a8
-#define SDRC_MCFG_1		0x0B0
-#define SDRC_MR_1		0x0B4
-#define SDRC_EMR2_1		0x0BC
-#define SDRC_ACTIM_CTRL_A_1	0x0C4
-#define SDRC_ACTIM_CTRL_B_1	0x0C8
-#define SDRC_RFR_CTRL_1		0x0D4
-#define SDRC_MANUAL_1		0x0D8
-
-#define SDRC_POWER_AUTOCOUNT_SHIFT	8
-#define SDRC_POWER_AUTOCOUNT_MASK	(0xffff << SDRC_POWER_AUTOCOUNT_SHIFT)
-#define SDRC_POWER_CLKCTRL_SHIFT	4
-#define SDRC_POWER_CLKCTRL_MASK		(0x3 << SDRC_POWER_CLKCTRL_SHIFT)
-#define SDRC_SELF_REFRESH_ON_AUTOCOUNT	(0x2 << SDRC_POWER_CLKCTRL_SHIFT)
-
-/*
- * These values represent the number of memory clock cycles between
- * autorefresh initiation.  They assume 1 refresh per 64 ms (JEDEC), 8192
- * rows per device, and include a subtraction of a 50 cycle window in the
- * event that the autorefresh command is delayed due to other SDRC activity.
- * The '| 1' sets the ARE field to send one autorefresh when the autorefresh
- * counter reaches 0.
- *
- * These represent optimal values for common parts, it won't work for all.
- * As long as you scale down, most parameters are still work, they just
- * become sub-optimal. The RFR value goes in the opposite direction. If you
- * don't adjust it down as your clock period increases the refresh interval
- * will not be met. Setting all parameters for complete worst case may work,
- * but may cut memory performance by 2x. Due to errata the DLLs need to be
- * unlocked and their value needs run time calibration.	A dynamic call is
- * need for that as no single right value exists acorss production samples.
- *
- * Only the FULL speed values are given. Current code is such that rate
- * changes must be made at DPLLoutx2. The actual value adjustment for low
- * frequency operation will be handled by omap_set_performance()
- *
- * By having the boot loader boot up in the fastest L4 speed available likely
- * will result in something which you can switch between.
- */
-#define SDRC_RFR_CTRL_165MHz	(0x00044c00 | 1)
-#define SDRC_RFR_CTRL_133MHz	(0x0003de00 | 1)
-#define SDRC_RFR_CTRL_100MHz	(0x0002da01 | 1)
-#define SDRC_RFR_CTRL_110MHz	(0x0002da01 | 1) /* Need to calc */
-#define SDRC_RFR_CTRL_BYPASS	(0x00005000 | 1) /* Need to calc */
-
-
-/*
- * SMS register access
- */
-
-#define OMAP242X_SMS_REGADDR(reg)					\
-		(void __iomem *)OMAP2_L3_IO_ADDRESS(OMAP2420_SMS_BASE + reg)
-#define OMAP243X_SMS_REGADDR(reg)					\
-		(void __iomem *)OMAP2_L3_IO_ADDRESS(OMAP243X_SMS_BASE + reg)
-#define OMAP343X_SMS_REGADDR(reg)					\
-		(void __iomem *)OMAP2_L3_IO_ADDRESS(OMAP343X_SMS_BASE + reg)
-
-/* SMS register offsets - read/write with sms_{read,write}_reg() */
-
-#define SMS_SYSCONFIG			0x010
-/* REVISIT: fill in other SMS registers here */
-
-
-#ifndef __ASSEMBLER__
-
-/**
- * struct omap_sdrc_params - SDRC parameters for a given SDRC clock rate
- * @rate: SDRC clock rate (in Hz)
- * @actim_ctrla: Value to program to SDRC_ACTIM_CTRLA for this rate
- * @actim_ctrlb: Value to program to SDRC_ACTIM_CTRLB for this rate
- * @rfr_ctrl: Value to program to SDRC_RFR_CTRL for this rate
- * @mr: Value to program to SDRC_MR for this rate
- *
- * This structure holds a pre-computed set of register values for the
- * SDRC for a given SDRC clock rate and SDRAM chip.  These are
- * intended to be pre-computed and specified in an array in the board-*.c
- * files.  The structure is keyed off the 'rate' field.
- */
-struct omap_sdrc_params {
-	unsigned long rate;
-	u32 actim_ctrla;
-	u32 actim_ctrlb;
-	u32 rfr_ctrl;
-	u32 mr;
-};
-
-#ifdef CONFIG_SOC_HAS_OMAP2_SDRC
-void omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
-			    struct omap_sdrc_params *sdrc_cs1);
-#else
-static inline void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
-					  struct omap_sdrc_params *sdrc_cs1) {};
-#endif
-
-int omap2_sdrc_get_params(unsigned long r,
-			  struct omap_sdrc_params **sdrc_cs0,
-			  struct omap_sdrc_params **sdrc_cs1);
-void omap2_sms_save_context(void);
-void omap2_sms_restore_context(void);
-
-#ifdef CONFIG_ARCH_OMAP2
-
-struct memory_timings {
-	u32 m_type;		/* ddr = 1, sdr = 0 */
-	u32 dll_mode;		/* use lock mode = 1, unlock mode = 0 */
-	u32 slow_dll_ctrl;	/* unlock mode, dll value for slow speed */
-	u32 fast_dll_ctrl;	/* unlock mode, dll value for fast speed */
-	u32 base_cs;		/* base chip select to use for calculations */
-};
-
-extern void omap2xxx_sdrc_init_params(u32 force_lock_to_unlock_mode);
-struct omap_sdrc_params *rx51_get_sdram_timings(void);
-
-u32 omap2xxx_sdrc_dll_is_unlocked(void);
-u32 omap2xxx_sdrc_reprogram(u32 level, u32 force);
-
-#endif  /* CONFIG_ARCH_OMAP2 */
-
-#endif  /* __ASSEMBLER__ */
-
-#endif