From 1f39847255a02c69190ae30c33b8ccf4c10840df Mon Sep 17 00:00:00 2001 From: Mark Lord Date: Tue, 27 May 2008 17:54:48 -0400 Subject: [PATCH 01/11] sata_mv: move SOC_FLAG to hpriv Convert the System-on-Chip flag from a host flag to an hpriv flag, for better consistency with other chip-rev flags, and for easier use in errata fixes etc. Also change the related "HAS_PCI()" into "!IS_SOC()" for better consistency of naming/use (everything else SOC-related already uses "SOC"). There are no functionality changes in this patch. Signed-off-by: Mark Lord Signed-off-by: Jeff Garzik --- drivers/ata/sata_mv.c | 27 +++++++++++++-------------- 1 file changed, 13 insertions(+), 14 deletions(-) diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index fb81f0c7a8c2..f6a716ef5a16 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -122,8 +122,6 @@ enum { /* Host Flags */ MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */ MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */ - /* SoC integrated controllers, no PCI interface */ - MV_FLAG_SOC = (1 << 28), MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI | @@ -362,6 +360,7 @@ enum { MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */ MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */ MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */ + MV_HP_FLAG_SOC = (1 << 11), /* SystemOnChip, no PCI */ /* Port private flags (pp_flags) */ MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */ @@ -374,7 +373,7 @@ enum { #define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II) #define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE) #define IS_PCIE(hpriv) ((hpriv)->hp_flags & MV_HP_PCIE) -#define HAS_PCI(host) (!((host)->ports[0]->flags & MV_FLAG_SOC)) +#define IS_SOC(hpriv) ((hpriv)->hp_flags & MV_HP_FLAG_SOC) #define WINDOW_CTRL(i) (0x20030 + ((i) << 4)) #define WINDOW_BASE(i) (0x20034 + ((i) << 4)) @@ -652,7 +651,7 @@ static const struct ata_port_info mv_port_info[] = { .port_ops = &mv_iie_ops, }, { /* chip_soc */ - .flags = MV_GENIIE_FLAGS | MV_FLAG_SOC, + .flags = MV_GENIIE_FLAGS, .pio_mask = 0x1f, /* pio0-4 */ .udma_mask = ATA_UDMA6, .port_ops = &mv_iie_ops, @@ -1254,7 +1253,7 @@ static void mv_edma_cfg(struct ata_port *ap, int want_ncq) cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */ cfg |= (1 << 22); /* enab 4-entry host queue cache */ - if (HAS_PCI(ap->host)) + if (!IS_SOC(hpriv)) cfg |= (1 << 18); /* enab early completion */ if (hpriv->hp_flags & MV_HP_CUT_THROUGH) cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */ @@ -2225,7 +2224,7 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance) * a bogus register value which can indicate HW removal or PCI fault. */ if (pending_irqs && main_irq_cause != 0xffffffffU) { - if (unlikely((pending_irqs & PCI_ERR) && HAS_PCI(host))) + if (unlikely((pending_irqs & PCI_ERR) && !IS_SOC(hpriv))) handled = mv_pci_error(host, hpriv->base); else handled = mv_host_intr(host, pending_irqs); @@ -2876,7 +2875,7 @@ static unsigned int mv_in_pcix_mode(struct ata_host *host) void __iomem *mmio = hpriv->base; u32 reg; - if (!HAS_PCI(host) || !IS_PCIE(hpriv)) + if (IS_SOC(hpriv) || !IS_PCIE(hpriv)) return 0; /* not PCI-X capable */ reg = readl(mmio + MV_PCI_MODE_OFS); if ((reg & MV_PCI_MODE_MASK) == 0) @@ -3018,7 +3017,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) break; case chip_soc: hpriv->ops = &mv_soc_ops; - hp_flags |= MV_HP_ERRATA_60X1C0; + hp_flags |= MV_HP_FLAG_SOC | MV_HP_ERRATA_60X1C0; break; default: @@ -3062,12 +3061,12 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx) if (rc) goto done; - if (HAS_PCI(host)) { - hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS; - hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS; - } else { + if (IS_SOC(hpriv)) { hpriv->main_irq_cause_addr = mmio + SOC_HC_MAIN_IRQ_CAUSE_OFS; hpriv->main_irq_mask_addr = mmio + SOC_HC_MAIN_IRQ_MASK_OFS; + } else { + hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS; + hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS; } /* global interrupt mask: 0 == mask everything */ @@ -3093,7 +3092,7 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx) mv_port_init(&ap->ioaddr, port_mmio); #ifdef CONFIG_PCI - if (HAS_PCI(host)) { + if (!IS_SOC(hpriv)) { unsigned int offset = port_mmio - mmio; ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio"); ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port"); @@ -3113,7 +3112,7 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx) writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS); } - if (HAS_PCI(host)) { + if (!IS_SOC(hpriv)) { /* Clear any currently outstanding host interrupt conditions */ writelfl(0, mmio + hpriv->irq_cause_ofs); From 8c30a8b9b574cf6c51e207464b852a6f559da153 Mon Sep 17 00:00:00 2001 From: Mark Lord Date: Tue, 27 May 2008 17:56:31 -0400 Subject: [PATCH 02/11] sata_mv: PHY_MODEx errata fixes Fix and update the errata handling for the PHY_MODEx registers. This improves receiver noise tolerance, among other things. Signed-off-by: Mark Lord Signed-off-by: Jeff Garzik --- drivers/ata/sata_mv.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index f6a716ef5a16..a39779aed8f5 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -2546,7 +2546,7 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0); int fix_phy_mode4 = hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0); - u32 m2, tmp; + u32 m2, m3; if (fix_phy_mode2) { m2 = readl(port_mmio + PHY_MODE2); @@ -2563,27 +2563,27 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, udelay(200); } - /* who knows what this magic does */ - tmp = readl(port_mmio + PHY_MODE3); - tmp &= ~0x7F800000; - tmp |= 0x2A800000; - writel(tmp, port_mmio + PHY_MODE3); + /* + * Gen-II/IIe PHY_MODE3 errata RM#2: + * Achieves better receiver noise performance than the h/w default: + */ + m3 = readl(port_mmio + PHY_MODE3); + m3 = (m3 & 0x1f) | (0x5555601 << 5); + writel(m3, port_mmio + PHY_MODE3); if (fix_phy_mode4) { u32 m4; m4 = readl(port_mmio + PHY_MODE4); - if (hp_flags & MV_HP_ERRATA_60X1B2) - tmp = readl(port_mmio + PHY_MODE3); - /* workaround for errata FEr SATA#10 (part 1) */ m4 = (m4 & ~(1 << 1)) | (1 << 0); - writel(m4, port_mmio + PHY_MODE4); + /* enforce bit restrictions on GenIIe devices */ + if (IS_GEN_IIE(hpriv)) + m4 = (m4 & ~0x5DE3FFFC) | (1 << 2); - if (hp_flags & MV_HP_ERRATA_60X1B2) - writel(tmp, port_mmio + PHY_MODE3); + writel(m4, port_mmio + PHY_MODE4); } /* Revert values of pre-emphasis and signal amps to the saved ones */ From 5cf73bfb061552aa18d816d2859409be9ace5306 Mon Sep 17 00:00:00 2001 From: Mark Lord Date: Tue, 27 May 2008 17:58:56 -0400 Subject: [PATCH 03/11] sata_mv: nuke unreleased GenIIe revisions The only public release of the 6042/7042 chips was/is revision "B0". Remove code that attempted to deal with earlier, non-released revs. This matches the logic of the current Marvell "proprietary" driver. Also, bump up the sata_mv version number, to reflect this batch of erratas. Signed-off-by: Mark Lord Signed-off-by: Jeff Garzik --- drivers/ata/sata_mv.c | 23 ++++------------------- 1 file changed, 4 insertions(+), 19 deletions(-) diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index a39779aed8f5..969a76987781 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -72,7 +72,7 @@ #include #define DRV_NAME "sata_mv" -#define DRV_VERSION "1.21" +#define DRV_VERSION "1.22" enum { /* BAR's are enumerated in terms of pci_resource_start() terms */ @@ -354,7 +354,6 @@ enum { MV_HP_ERRATA_50XXB2 = (1 << 2), MV_HP_ERRATA_60X1B2 = (1 << 3), MV_HP_ERRATA_60X1C0 = (1 << 4), - MV_HP_ERRATA_XX42A0 = (1 << 5), MV_HP_GEN_I = (1 << 6), /* Generation I: 50xx */ MV_HP_GEN_II = (1 << 7), /* Generation II: 60xx */ MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */ @@ -811,12 +810,7 @@ static void mv_set_edma_ptrs(void __iomem *port_mmio, writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS); writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | index, port_mmio + EDMA_REQ_Q_IN_PTR_OFS); - - if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0) - writelfl((pp->crqb_dma & 0xffffffff) | index, - port_mmio + EDMA_REQ_Q_OUT_PTR_OFS); - else - writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS); + writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS); /* * initialize response queue @@ -826,13 +820,7 @@ static void mv_set_edma_ptrs(void __iomem *port_mmio, WARN_ON(pp->crpb_dma & 0xff); writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS); - - if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0) - writelfl((pp->crpb_dma & 0xffffffff) | index, - port_mmio + EDMA_RSP_Q_IN_PTR_OFS); - else - writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS); - + writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS); writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | index, port_mmio + EDMA_RSP_Q_OUT_PTR_OFS); } @@ -3002,10 +2990,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) hp_flags |= MV_HP_CUT_THROUGH; switch (pdev->revision) { - case 0x0: - hp_flags |= MV_HP_ERRATA_XX42A0; - break; - case 0x1: + case 0x2: /* Rev.B0: the first/only public release */ hp_flags |= MV_HP_ERRATA_60X1C0; break; default: From b406c7a6655da7a2fcd9f72e41262f93ff707748 Mon Sep 17 00:00:00 2001 From: Mark Lord Date: Wed, 28 May 2008 12:01:12 -0400 Subject: [PATCH 04/11] sata_mv: workaround for 60x1 errata sata13 The "B2" variant of the 6041/6081 (genII) chips requires that the PHY_MODE3 register be rewritten after any write to PHY_MODE4. This fixes a regression introduced by an earlier patch. Signed-off-by: Mark Lord Signed-off-by: Jeff Garzik --- drivers/ata/sata_mv.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 969a76987781..17093e600d80 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -72,7 +72,7 @@ #include #define DRV_NAME "sata_mv" -#define DRV_VERSION "1.22" +#define DRV_VERSION "1.23" enum { /* BAR's are enumerated in terms of pci_resource_start() terms */ @@ -2557,7 +2557,6 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, */ m3 = readl(port_mmio + PHY_MODE3); m3 = (m3 & 0x1f) | (0x5555601 << 5); - writel(m3, port_mmio + PHY_MODE3); if (fix_phy_mode4) { u32 m4; @@ -2573,6 +2572,12 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, writel(m4, port_mmio + PHY_MODE4); } + /* + * Workaround for 60x1-B2 errata SATA#13: + * Any write to PHY_MODE4 (above) may corrupt PHY_MODE3, + * so we must always rewrite PHY_MODE3 after PHY_MODE4. + */ + writel(m3, port_mmio + PHY_MODE3); /* Revert values of pre-emphasis and signal amps to the saved ones */ m2 = readl(port_mmio + PHY_MODE2); From 0388a8c0d54aa039758a8eca68d82325a563f8db Mon Sep 17 00:00:00 2001 From: Mark Lord Date: Wed, 28 May 2008 13:41:52 -0400 Subject: [PATCH 05/11] sata_mv: implement SoC guideline SATA_S11 The 5182 System-On-Chip (SOC) variant wants certain lower bits to be cleared on any write to the PHY_MODE3 register. If/when support is added for other SOC variants, we'll need some way to uniquely identify the 5182, and not perform this workaround for the others. But for now, it is the only SOC variant we support here. Signed-off-by: Mark Lord Signed-off-by: Jeff Garzik --- drivers/ata/sata_mv.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 17093e600d80..acf347f71a2f 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -72,7 +72,7 @@ #include #define DRV_NAME "sata_mv" -#define DRV_VERSION "1.23" +#define DRV_VERSION "1.24" enum { /* BAR's are enumerated in terms of pci_resource_start() terms */ @@ -2558,6 +2558,10 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, m3 = readl(port_mmio + PHY_MODE3); m3 = (m3 & 0x1f) | (0x5555601 << 5); + /* Guideline 88F5182 (GL# SATA-S11) */ + if (IS_SOC(hpriv)) + m3 &= ~0x1c; + if (fix_phy_mode4) { u32 m4; From 23cf296e3b047da46112eb6b4dc89917c93c8f19 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Thu, 29 May 2008 22:04:22 +0900 Subject: [PATCH 06/11] ata_piix: fix macbook ich8m problems ICH8M on macbooks are peculiar in that some of them lock up when the second port is enabled, some return bogus values on SIDPR access while yet others hang on SIDPR access. Also, the ich8m_apple_sata entry was wrongly added below generic ich8m entry making it virtually useless. This patch works around macbook ich8m problems by * moving ich8m_apple_sata entry above generic ich8m entry * dropping PIIX_FLAG_SIDPR from ich8m_apple_sata * adding subsystem 106b:00a1 as ich8m_apple_sata Reported and tested by MATSUBAYASHI. Signed-off-by: Tejun Heo Cc: MATSUBAYASHI 'Shaolin' Kohji Signed-off-by: Jeff Garzik --- drivers/ata/ata_piix.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index a9027b8fbdd5..3548ee7014ca 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -247,10 +247,11 @@ static const struct pci_device_id piix_pci_tbl[] = { { 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, /* SATA Controller 2 IDE (ICH8) */ { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, - /* Mobile SATA Controller IDE (ICH8M) */ - { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, /* Mobile SATA Controller IDE (ICH8M), Apple */ { 0x8086, 0x2828, 0x106b, 0x00a0, 0, 0, ich8m_apple_sata }, + { 0x8086, 0x2828, 0x106b, 0x00a1, 0, 0, ich8m_apple_sata }, + /* Mobile SATA Controller IDE (ICH8M) */ + { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, /* SATA Controller IDE (ICH9) */ { 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, /* SATA Controller IDE (ICH9) */ @@ -526,7 +527,7 @@ static struct ata_port_info piix_port_info[] = { [ich8m_apple_sata] = { - .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR, + .flags = PIIX_SATA_FLAGS, .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = ATA_UDMA6, From 2da676594a73825f10d2a99358cc7465119684f9 Mon Sep 17 00:00:00 2001 From: Pradeep Singh Rautela Date: Thu, 29 May 2008 23:28:14 +0530 Subject: [PATCH 07/11] ata: Convert to static DEFINE_SPINLOCK(lock) Replace deprecated static spinlock_t instance to static DEFINE_SPINLOCK(lock). Signed-off-by: Pradeep Singh Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 3c89f205c83f..cc816ca623d3 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -5403,7 +5403,7 @@ static void ata_host_stop(struct device *gendev, void *res) */ static void ata_finalize_port_ops(struct ata_port_operations *ops) { - static spinlock_t lock = SPIN_LOCK_UNLOCKED; + static DEFINE_SPINLOCK(lock); const struct ata_port_operations *cur; void **begin = (void **)ops; void **end = (void **)&ops->inherits; From ec2a20e61974f7c9ebe6dd99ac479ec309a750bc Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Wed, 30 Apr 2008 12:57:00 -0700 Subject: [PATCH 08/11] libata: fix libata-scsi kernel-doc notation Fix libata-scsi kernel-doc notation: Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1659): No description found for parameter 'cmd' Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1971): No description found for parameter 'buf' Signed-off-by: Randy Dunlap Signed-off-by: Jeff Garzik --- drivers/ata/libata-scsi.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c index aeb6e01d82ce..2e6e1622dc6d 100644 --- a/drivers/ata/libata-scsi.c +++ b/drivers/ata/libata-scsi.c @@ -1637,6 +1637,7 @@ static int ata_scsi_translate(struct ata_device *dev, struct scsi_cmnd *cmd, /** * ata_scsi_rbuf_get - Map response buffer. + * @cmd: SCSI command containing buffer to be mapped. * @flags: unsigned long variable to store irq enable status * @copy_in: copy in from user buffer * @@ -1954,7 +1955,7 @@ static unsigned int ata_msense_ctl_mode(u8 *buf) /** * ata_msense_rw_recovery - Simulate MODE SENSE r/w error recovery page - * @bufp: output buffer + * @buf: output buffer * * Generate a generic MODE SENSE r/w error recovery page. * From 19ef9d5e45ce805700f34c248a71a511877b8a5d Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Wed, 21 May 2008 14:11:24 +0900 Subject: [PATCH 09/11] libata: SRST can't be trusted on PMP sil3726 As in sil4726, SRST can't be trusted on sil3726 causing detection problems under certain configuraitons. I thought it was from the Config Disk device but apparently not. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/libata-pmp.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/drivers/ata/libata-pmp.c b/drivers/ata/libata-pmp.c index 0f9386d4a5a0..7daf4c0f6216 100644 --- a/drivers/ata/libata-pmp.c +++ b/drivers/ata/libata-pmp.c @@ -322,9 +322,12 @@ static void sata_pmp_quirks(struct ata_port *ap) if (vendor == 0x1095 && devid == 0x3726) { /* sil3726 quirks */ ata_port_for_each_link(link, ap) { - /* class code report is unreliable */ + /* Class code report is unreliable and SRST + * times out under certain configurations. + */ if (link->pmp < 5) - link->flags |= ATA_LFLAG_ASSUME_ATA; + link->flags |= ATA_LFLAG_NO_SRST | + ATA_LFLAG_ASSUME_ATA; /* port 5 is for SEMB device and it doesn't like SRST */ if (link->pmp == 5) From 034d8e8f273fcb02bebd6a62d8023ffa409fe92f Mon Sep 17 00:00:00 2001 From: Ashish Kalra Date: Tue, 20 May 2008 00:19:45 -0500 Subject: [PATCH 10/11] [libata] sata_fsl: Fix broken driver, add port multiplier (PMP) support The following commit (4c9bf4e799ce06a7378f1196587084802a414c03): libata: replace tf_read with qc_fill_rtf for non-SFF drivers Broke the sata_fsl.c driver in 2.6.26-rc. I know the following patch fixes the issue, it clearly also adds port multipler support. The current 2.6.26-rc driver is broken. On boot with debug enabled we get something like (w/o this patch): spurious interrupt!!, CC = 0x1 interrupt status 0x1 xx_scr_read, reg_in = 1 spurious interrupt!!, CC = 0x1 interrupt status 0x1 xx_scr_read, reg_in = 1 spurious interrupt!!, CC = 0x1 interrupt status 0x1 xx_scr_read, reg_in = 1 .. continues for ever. This change fixes this as a side effect of adding port multiplier support. Signed-off-by: Ashish Kalra Signed-off-by: Jeff Garzik --- drivers/ata/sata_fsl.c | 218 ++++++++++++++++++++++++++++++----------- 1 file changed, 160 insertions(+), 58 deletions(-) diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c index 853559e32315..3924e7209a44 100644 --- a/drivers/ata/sata_fsl.c +++ b/drivers/ata/sata_fsl.c @@ -34,7 +34,7 @@ enum { SATA_FSL_HOST_FLAGS = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA | - ATA_FLAG_NCQ), + ATA_FLAG_PMP | ATA_FLAG_NCQ), SATA_FSL_MAX_CMDS = SATA_FSL_QUEUE_DEPTH, SATA_FSL_CMD_HDR_SIZE = 16, /* 4 DWORDS */ @@ -395,7 +395,7 @@ static void sata_fsl_qc_prep(struct ata_queued_cmd *qc) cd = (struct command_desc *)pp->cmdentry + tag; cd_paddr = pp->cmdentry_paddr + tag * SATA_FSL_CMD_DESC_SIZE; - ata_tf_to_fis(&qc->tf, 0, 1, (u8 *) &cd->cfis); + ata_tf_to_fis(&qc->tf, qc->dev->link->pmp, 1, (u8 *) &cd->cfis); VPRINTK("Dumping cfis : 0x%x, 0x%x, 0x%x\n", cd->cfis[0], cd->cfis[1], cd->cfis[2]); @@ -438,6 +438,8 @@ static unsigned int sata_fsl_qc_issue(struct ata_queued_cmd *qc) ioread32(CA + hcr_base), ioread32(CE + hcr_base), ioread32(CC + hcr_base)); + iowrite32(qc->dev->link->pmp, CQPMP + hcr_base); + /* Simply queue command to the controller/device */ iowrite32(1 << tag, CQ + hcr_base); @@ -558,11 +560,36 @@ static void sata_fsl_thaw(struct ata_port *ap) ioread32(hcr_base + HCONTROL), ioread32(hcr_base + HSTATUS)); } +static void sata_fsl_pmp_attach(struct ata_port *ap) +{ + struct sata_fsl_host_priv *host_priv = ap->host->private_data; + void __iomem *hcr_base = host_priv->hcr_base; + u32 temp; + + temp = ioread32(hcr_base + HCONTROL); + iowrite32((temp | HCONTROL_PMP_ATTACHED), hcr_base + HCONTROL); +} + +static void sata_fsl_pmp_detach(struct ata_port *ap) +{ + struct sata_fsl_host_priv *host_priv = ap->host->private_data; + void __iomem *hcr_base = host_priv->hcr_base; + u32 temp; + + temp = ioread32(hcr_base + HCONTROL); + temp &= ~HCONTROL_PMP_ATTACHED; + iowrite32(temp, hcr_base + HCONTROL); + + /* enable interrupts on the controller/port */ + temp = ioread32(hcr_base + HCONTROL); + iowrite32((temp | DEFAULT_PORT_IRQ_ENABLE_MASK), hcr_base + HCONTROL); + +} + static int sata_fsl_port_start(struct ata_port *ap) { struct device *dev = ap->host->dev; struct sata_fsl_port_priv *pp; - int retval; void *mem; dma_addr_t mem_dma; struct sata_fsl_host_priv *host_priv = ap->host->private_data; @@ -688,12 +715,13 @@ static int sata_fsl_prereset(struct ata_link *link, unsigned long deadline) } static int sata_fsl_softreset(struct ata_link *link, unsigned int *class, - unsigned long deadline) + unsigned long deadline) { struct ata_port *ap = link->ap; struct sata_fsl_port_priv *pp = ap->private_data; struct sata_fsl_host_priv *host_priv = ap->host->private_data; void __iomem *hcr_base = host_priv->hcr_base; + int pmp = sata_srst_pmp(link); u32 temp; struct ata_taskfile tf; u8 *cfis; @@ -703,6 +731,9 @@ static int sata_fsl_softreset(struct ata_link *link, unsigned int *class, DPRINTK("in xx_softreset\n"); + if (pmp != SATA_PMP_CTRL_PORT) + goto issue_srst; + try_offline_again: /* * Force host controller to go off-line, aborting current operations @@ -746,6 +777,7 @@ static int sata_fsl_softreset(struct ata_link *link, unsigned int *class, temp = ioread32(hcr_base + HCONTROL); temp |= (HCONTROL_ONLINE_PHY_RST | HCONTROL_SNOOP_ENABLE); + temp |= HCONTROL_PMP_ATTACHED; iowrite32(temp, hcr_base + HCONTROL); temp = ata_wait_register(hcr_base + HSTATUS, ONLINE, 0, 1, 500); @@ -771,7 +803,8 @@ static int sata_fsl_softreset(struct ata_link *link, unsigned int *class, ata_port_printk(ap, KERN_WARNING, "No Device OR PHYRDY change,Hstatus = 0x%x\n", ioread32(hcr_base + HSTATUS)); - goto err; + *class = ATA_DEV_NONE; + goto out; } /* @@ -783,7 +816,8 @@ static int sata_fsl_softreset(struct ata_link *link, unsigned int *class, if ((temp & 0xFF) != 0x18) { ata_port_printk(ap, KERN_WARNING, "No Signature Update\n"); - goto err; + *class = ATA_DEV_NONE; + goto out; } else { ata_port_printk(ap, KERN_INFO, "Signature Update detected @ %d msecs\n", @@ -798,6 +832,7 @@ static int sata_fsl_softreset(struct ata_link *link, unsigned int *class, * reached here, we can send a command to the target device */ +issue_srst: DPRINTK("Sending SRST/device reset\n"); ata_tf_init(link->device, &tf); @@ -808,7 +843,7 @@ static int sata_fsl_softreset(struct ata_link *link, unsigned int *class, SRST_CMD | CMD_DESC_SNOOP_ENABLE, 0, 0, 5); tf.ctl |= ATA_SRST; /* setup SRST bit in taskfile control reg */ - ata_tf_to_fis(&tf, 0, 0, cfis); + ata_tf_to_fis(&tf, pmp, 0, cfis); DPRINTK("Dumping cfis : 0x%x, 0x%x, 0x%x, 0x%x\n", cfis[0], cfis[1], cfis[2], cfis[3]); @@ -854,8 +889,10 @@ static int sata_fsl_softreset(struct ata_link *link, unsigned int *class, sata_fsl_setup_cmd_hdr_entry(pp, 0, CMD_DESC_SNOOP_ENABLE, 0, 0, 5); tf.ctl &= ~ATA_SRST; /* 2nd H2D Ctl. register FIS */ - ata_tf_to_fis(&tf, 0, 0, cfis); + ata_tf_to_fis(&tf, pmp, 0, cfis); + if (pmp != SATA_PMP_CTRL_PORT) + iowrite32(pmp, CQPMP + hcr_base); iowrite32(1, CQ + hcr_base); msleep(150); /* ?? */ @@ -886,12 +923,21 @@ static int sata_fsl_softreset(struct ata_link *link, unsigned int *class, VPRINTK("cereg = 0x%x\n", ioread32(hcr_base + CE)); } +out: return 0; err: return -EIO; } +static void sata_fsl_error_handler(struct ata_port *ap) +{ + + DPRINTK("in xx_error_handler\n"); + sata_pmp_error_handler(ap); + +} + static void sata_fsl_post_internal_cmd(struct ata_queued_cmd *qc) { if (qc->flags & ATA_QCFLAG_FAILED) @@ -905,18 +951,21 @@ static void sata_fsl_post_internal_cmd(struct ata_queued_cmd *qc) static void sata_fsl_error_intr(struct ata_port *ap) { - struct ata_link *link = &ap->link; - struct ata_eh_info *ehi = &link->eh_info; struct sata_fsl_host_priv *host_priv = ap->host->private_data; void __iomem *hcr_base = host_priv->hcr_base; - u32 hstatus, dereg, cereg = 0, SError = 0; + u32 hstatus, dereg=0, cereg = 0, SError = 0; unsigned int err_mask = 0, action = 0; - struct ata_queued_cmd *qc; - int freeze = 0; + int freeze = 0, abort=0; + struct ata_link *link = NULL; + struct ata_queued_cmd *qc = NULL; + struct ata_eh_info *ehi; hstatus = ioread32(hcr_base + HSTATUS); cereg = ioread32(hcr_base + CE); + /* first, analyze and record host port events */ + link = &ap->link; + ehi = &link->eh_info; ata_ehi_clear_desc(ehi); /* @@ -926,12 +975,41 @@ static void sata_fsl_error_intr(struct ata_port *ap) sata_fsl_scr_read(ap, SCR_ERROR, &SError); if (unlikely(SError & 0xFFFF0000)) { sata_fsl_scr_write(ap, SCR_ERROR, SError); - err_mask |= AC_ERR_ATA_BUS; } DPRINTK("error_intr,hStat=0x%x,CE=0x%x,DE =0x%x,SErr=0x%x\n", hstatus, cereg, ioread32(hcr_base + DE), SError); + /* handle fatal errors */ + if (hstatus & FATAL_ERROR_DECODE) { + ehi->err_mask |= AC_ERR_ATA_BUS; + ehi->action |= ATA_EH_SOFTRESET; + + /* + * Ignore serror in case of fatal errors as we always want + * to do a soft-reset of the FSL SATA controller. Analyzing + * serror may cause libata to schedule a hard-reset action, + * and hard-reset currently does not do controller + * offline/online, causing command timeouts and leads to an + * un-recoverable state, hence make libATA ignore + * autopsy in case of fatal errors. + */ + + ehi->flags |= ATA_EHI_NO_AUTOPSY; + + freeze = 1; + } + + /* Handle PHYRDY change notification */ + if (hstatus & INT_ON_PHYRDY_CHG) { + DPRINTK("SATA FSL: PHYRDY change indication\n"); + + /* Setup a soft-reset EH action */ + ata_ehi_hotplugged(ehi); + ata_ehi_push_desc(ehi, "%s", "PHY RDY changed"); + freeze = 1; + } + /* handle single device errors */ if (cereg) { /* @@ -943,58 +1021,68 @@ static void sata_fsl_error_intr(struct ata_port *ap) * clearing the device error, we can issue commands to the * device to interrogate it to find the source of the error. */ - dereg = ioread32(hcr_base + DE); - iowrite32(dereg, hcr_base + DE); - iowrite32(cereg, hcr_base + CE); + abort = 1; DPRINTK("single device error, CE=0x%x, DE=0x%x\n", ioread32(hcr_base + CE), ioread32(hcr_base + DE)); - /* - * We should consider this as non fatal error, and TF must - * be updated as done below. - */ - err_mask |= AC_ERR_DEV; - } + /* find out the offending link and qc */ + if (ap->nr_pmp_links) { + dereg = ioread32(hcr_base + DE); + iowrite32(dereg, hcr_base + DE); + iowrite32(cereg, hcr_base + CE); - /* handle fatal errors */ - if (hstatus & FATAL_ERROR_DECODE) { - err_mask |= AC_ERR_ATA_BUS; - action |= ATA_EH_RESET; - /* how will fatal error interrupts be completed ?? */ - freeze = 1; - } + if (dereg < ap->nr_pmp_links) { + link = &ap->pmp_link[dereg]; + ehi = &link->eh_info; + qc = ata_qc_from_tag(ap, link->active_tag); + /* + * We should consider this as non fatal error, + * and TF must be updated as done below. + */ - /* Handle PHYRDY change notification */ - if (hstatus & INT_ON_PHYRDY_CHG) { - DPRINTK("SATA FSL: PHYRDY change indication\n"); + err_mask |= AC_ERR_DEV; - /* Setup a soft-reset EH action */ - ata_ehi_hotplugged(ehi); - freeze = 1; + } else { + err_mask |= AC_ERR_HSM; + action |= ATA_EH_HARDRESET; + freeze = 1; + } + } else { + dereg = ioread32(hcr_base + DE); + iowrite32(dereg, hcr_base + DE); + iowrite32(cereg, hcr_base + CE); + + qc = ata_qc_from_tag(ap, link->active_tag); + /* + * We should consider this as non fatal error, + * and TF must be updated as done below. + */ + err_mask |= AC_ERR_DEV; + } } /* record error info */ - qc = ata_qc_from_tag(ap, link->active_tag); - - if (qc) + if (qc) { qc->err_mask |= err_mask; - else + } else ehi->err_mask |= err_mask; ehi->action |= action; - ehi->serror |= SError; /* freeze or abort */ if (freeze) ata_port_freeze(ap); - else - ata_port_abort(ap); + else if (abort) { + if (qc) + ata_link_abort(qc->dev->link); + else + ata_port_abort(ap); + } } static void sata_fsl_host_intr(struct ata_port *ap) { - struct ata_link *link = &ap->link; struct sata_fsl_host_priv *host_priv = ap->host->private_data; void __iomem *hcr_base = host_priv->hcr_base; u32 hstatus, qc_active = 0; @@ -1017,10 +1105,19 @@ static void sata_fsl_host_intr(struct ata_port *ap) return; } - if (link->sactive) { /* only true for NCQ commands */ + /* Read command completed register */ + qc_active = ioread32(hcr_base + CC); + + VPRINTK("Status of all queues :\n"); + VPRINTK("qc_active/CC = 0x%x, CA = 0x%x, CE=0x%x,CQ=0x%x,apqa=0x%x\n", + qc_active, + ioread32(hcr_base + CA), + ioread32(hcr_base + CE), + ioread32(hcr_base + CQ), + ap->qc_active); + + if (qc_active & ap->qc_active) { int i; - /* Read command completed register */ - qc_active = ioread32(hcr_base + CC); /* clear CC bit, this will also complete the interrupt */ iowrite32(qc_active, hcr_base + CC); @@ -1032,8 +1129,9 @@ static void sata_fsl_host_intr(struct ata_port *ap) for (i = 0; i < SATA_FSL_QUEUE_DEPTH; i++) { if (qc_active & (1 << i)) { qc = ata_qc_from_tag(ap, i); - if (qc) + if (qc) { ata_qc_complete(qc); + } DPRINTK ("completing ncq cmd,tag=%d,CC=0x%x,CA=0x%x\n", i, ioread32(hcr_base + CC), @@ -1042,19 +1140,21 @@ static void sata_fsl_host_intr(struct ata_port *ap) } return; - } else if (ap->qc_active) { + } else if ((ap->qc_active & (1 << ATA_TAG_INTERNAL))) { iowrite32(1, hcr_base + CC); - qc = ata_qc_from_tag(ap, link->active_tag); + qc = ata_qc_from_tag(ap, ATA_TAG_INTERNAL); - DPRINTK("completing non-ncq cmd, tag=%d,CC=0x%x\n", - link->active_tag, ioread32(hcr_base + CC)); + DPRINTK("completing non-ncq cmd, CC=0x%x\n", + ioread32(hcr_base + CC)); - if (qc) + if (qc) { ata_qc_complete(qc); + } } else { /* Spurious Interrupt!! */ DPRINTK("spurious interrupt!!, CC = 0x%x\n", ioread32(hcr_base + CC)); + iowrite32(qc_active, hcr_base + CC); return; } } @@ -1130,9 +1230,6 @@ static int sata_fsl_init_controller(struct ata_host *host) iowrite32(0x00000FFFF, hcr_base + CE); iowrite32(0x00000FFFF, hcr_base + DE); - /* initially assuming no Port multiplier, set CQPMP to 0 */ - iowrite32(0x0, hcr_base + CQPMP); - /* * host controller will be brought on-line, during xx_port_start() * callback, that should also initiate the OOB, COMINIT sequence @@ -1154,8 +1251,8 @@ static struct scsi_host_template sata_fsl_sht = { .dma_boundary = ATA_DMA_BOUNDARY, }; -static const struct ata_port_operations sata_fsl_ops = { - .inherits = &sata_port_ops, +static struct ata_port_operations sata_fsl_ops = { + .inherits = &sata_pmp_port_ops, .qc_prep = sata_fsl_qc_prep, .qc_issue = sata_fsl_qc_issue, @@ -1168,10 +1265,15 @@ static const struct ata_port_operations sata_fsl_ops = { .thaw = sata_fsl_thaw, .prereset = sata_fsl_prereset, .softreset = sata_fsl_softreset, + .pmp_softreset = sata_fsl_softreset, + .error_handler = sata_fsl_error_handler, .post_internal_cmd = sata_fsl_post_internal_cmd, .port_start = sata_fsl_port_start, .port_stop = sata_fsl_port_stop, + + .pmp_attach = sata_fsl_pmp_attach, + .pmp_detach = sata_fsl_pmp_detach, }; static const struct ata_port_info sata_fsl_port_info[] = { From 3072c379bccfa2844e33103ed9ff530780e660ea Mon Sep 17 00:00:00 2001 From: peerchen Date: Mon, 19 May 2008 14:44:57 +0800 Subject: [PATCH 11/11] ahci: change the Device IDs of nvidia MCP7B AHCI controller in ahci.c Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c, as the actual PCI IDs deployed in the field differed from the forecasted ones preemptively placed in the driver. Signed-off-by: Peer Chen Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index 97f83fb2ee2e..544b7d6c617c 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -502,10 +502,10 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_VDEVICE(NVIDIA, 0x0bcd), board_ahci }, /* MCP7B */ { PCI_VDEVICE(NVIDIA, 0x0bce), board_ahci }, /* MCP7B */ { PCI_VDEVICE(NVIDIA, 0x0bcf), board_ahci }, /* MCP7B */ - { PCI_VDEVICE(NVIDIA, 0x0bd0), board_ahci }, /* MCP7B */ - { PCI_VDEVICE(NVIDIA, 0x0bd1), board_ahci }, /* MCP7B */ - { PCI_VDEVICE(NVIDIA, 0x0bd2), board_ahci }, /* MCP7B */ - { PCI_VDEVICE(NVIDIA, 0x0bd3), board_ahci }, /* MCP7B */ + { PCI_VDEVICE(NVIDIA, 0x0bc4), board_ahci }, /* MCP7B */ + { PCI_VDEVICE(NVIDIA, 0x0bc5), board_ahci }, /* MCP7B */ + { PCI_VDEVICE(NVIDIA, 0x0bc6), board_ahci }, /* MCP7B */ + { PCI_VDEVICE(NVIDIA, 0x0bc7), board_ahci }, /* MCP7B */ /* SiS */ { PCI_VDEVICE(SI, 0x1184), board_ahci }, /* SiS 966 */