Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6310 that uses the AHCI driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
while I was looking over kernel sources I've found this small bug.
Formerly, zero was returned even if an error happened.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.
Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported. Although if DMA is
available, we do take advantage of it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table. I add a
new column for dmack_hold time. The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Port enabledness test fits much better into init_one() instead of
pre_reset(). The reason why these tests are in pre_reset() is purely
historical at this point. Move it to init_one(). This will help
further changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The UDMA affliction is apparently specific to revision 0x11. Keeps us in sync
with drivers/ide current.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a wrong WARN_ON that was triggered by 32bit PIO support:
WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()
__atapi_pio_bytes simply doesnt know enough to decide if there is a bug.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In a discussio with Jeff Garzik, he mentioned that the serialization
for the libata port probes only needs to be within the domain of a host.
This means that for the first port of each host (with ID 0), we don't
need to wait, so we can relax our serialization a little.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a per host flag that allows drivers to opt in into
having its busses scanned in parallel.
Drivers that do not set this flag get their ports scanned in
the "original" sequence.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (94 commits)
ACPICA: hide private headers
ACPICA: create acpica/ directory
ACPI: fix build warning
ACPI : Use RSDT instead of XSDT by adding boot option of "acpi=rsdt"
ACPI: Avoid array address overflow when _CST MWAIT hint bits are set
fujitsu-laptop: Simplify SBLL/SBL2 backlight handling
fujitsu-laptop: Add BL power, LED control and radio state information
ACPICA: delete utcache.c
ACPICA: delete acdisasm.h
ACPICA: Update version to 20081204.
ACPICA: FADT: Update error msgs for consistency
ACPICA: FADT: set acpi_gbl_use_default_register_widths to TRUE by default
ACPICA: FADT parsing changes and fixes
ACPICA: Add ACPI_MUTEX_TYPE configuration option
ACPICA: Fixes for various ACPI data tables
ACPICA: Restructure includes into public/private
ACPI: remove private acpica headers from driver files
ACPI: reboot.c: use new acpi_reset interface
ACPICA: New: acpi_reset interface - write to reset register
ACPICA: Move all public H/W interfaces to new hwxface
...
Convert WARN_ON() on command issue/completion paths to WARN_ON_ONCE()
so that libata doesn't spam the machine even when one of those
conditions triggers repeatedly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is an issue in ATI SB600/SB700 SATA that PxSERR.E should not be
set on some conditions, which will lead to many SATA ODD error messages.
commit 55a61604cd is the workaround.
Since SB800 fixed this HW issue, IGN_SERR_INTERNAL should be withdrawn
for SB800.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reimplement mode programming logic of pata_hpt366 such that it's
identical to that of IDE hpt366 driver. The differences were...
* pata_hpt366 used 0xCFFF8FFFF to mask pio modes and 0x3FFFFFFF dma
modes. IDE hpt366 uses 0xC1F8FFFF for PIO, 0x303800FF for MWDMA and
0x30070000 for UDMA.
* pata_hpt366 doesn't set 0x08000000 for PIO unless it's already set
and always turns it on for MWDMA/UDMA. IDE hpt366 doesn't bother
with the bit. It always uses what was there.
* IDE hpt366 always clears 0xC0000000. pata_hpt366 doesn't.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to the Compact Flash specification r4.1, PIO modes 5 and 6
do not use iordy.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
--
UPD include/linux/compile.h
`___pata_platform_remove' referenced in section `__ksymtab_gpl' of
drivers/built-in.o: defined in discarded section `.devexit.text' of
drivers/built-in.o
make: *** [.tmp_vmlinux1] Error 1
--
__pata_platform_remove() should not be in discarded section
__pata_platform_remove(struct device *dev) is invoked in both
pata_platform.c and pata_of_platform.c by reomve function defined in
discarded section ".devexit.text". An exported function should not be put
into discarded section.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
AFAICT, struct sil24_port_multiplier isn't used anywhere. Remove it.
Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The present AHCI driver seems to support SATA GEN 3 speed, but the related
messages should be modified.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Certain ACPI implementations mess up IOCFG on _STM making libata
detect cable type incorrectly after a suspend/resume cycle. This
patch makes ata_piix save IOCFG on attach, use the saved value for
things which aren't dynamic and restore it on detach so that the next
driver also gets the BIOS initialized value.
This patch contains the following changes.
* makes ich_pata_cable_detect() use saved_iocfg.
* make piix_iocfg_bit18_quirk() take @host and use saved_iocfg.
* hpriv allocation moved upwards to save iocfg before doing anything
else.
This fixes bz#11879. Andreas Mohr reported and diagnosed the problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In very obscure cases this can cause problems. We need to help the hardware
out a bit to avoid DMA problems on a reset.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Correct the DMA bit flags (UDMA and MWDMA were swapped)
Add workarounds so that we clear ERR and INTR bits before issuing a DMA
Add workarounds so that we stop a live DMA before touching the CTL register
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As suggested by Linus: Don't do the libata init in 2 separate
steps with a global sync inbetween, but do it as one async step,
with a local sync before registering the device.
This cuts the boottime on my machine with 2 sata controllers down
significantly, and it seems to work. Would be nice if the libata
folks take a good look at this patch though..
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
This patch makes the libata port scanning asynchronous (per device).
There is a synchronization point before doing the actual disk scan
so that device ordering is not affected.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
External driver files should not include any private acpica headers.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This implements support for the Large Block Transfer feature found in Silicon
Image 311x controllers. This allows transferring bigger contiguous chunks of
data from system memory and avoids the 64KB boundary restriction of standard
SFF controllers.
This is based on a patch from Jeff Garzik (from the sii-lbt branch of
libata-dev) but includes a few bug fixes: Since the bmdma2 register does not
implement the status bits, the original bmdma register must be used except
where the bmdma2 register is required. As well the DMA boundary should be
31-bit instead of 32-bit since the top bit of the length field is still
required for the PRD end-of-table flag.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit
ATA: piix, fix pointer deref on suspend
fixed a possible oops in an ugly manner. Use newly introduced dmi_match()
to make the code pretty again.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The patchlet below blacklists NCQ on OCZ CORE v2 SSD drive(s). Even
though the drive advertises NCQ support with queue depth 1, it responds
with all-zeroes FIS to NCQ commands which triggers ata error handling
several times before the kernel decides to disable NCQ on the drive.
Signed-off-by: Lubomir Bulej <lubomir.bulej@dsrg.mff.cuni.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_port_detach() first made sure EH saw ATA_PFLAG_UNLOADING and then
assumed EH context belongs to it and performed detach operation
itself. However, UNLOADING doesn't disable all of EH and this could
lead to problems including triggering WARN_ON()'s in EH path.
This patch makes port detach behave more like other EH actions such
that ata_port_detach() requests EH to detach and waits for completion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When restoring SControl during detach, PMP links should be handled
first as changing SControl of the host link can affect SCR access of
PMP links.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There currently are the following looping constructs.
* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order
Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link. Instead of adding another one with long name, do the following
cleanup.
* Implement and export ata_link_next() and ata_dev_next() which take
@mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
looping mode explicitly.
The following iteration modes are implemented.
* ATA_LITER_EDGE : loop over edge links
* ATA_LITER_HOST_FIRST : loop over all links, host link first
* ATA_LITER_PMP_FIRST : loop over all links, PMP links first
* ATA_DITER_ENABLED : loop over enabled devices
* ATA_DITER_ENABLED_REVERSE : loop over enabled devices in reverse order
* ATA_DITER_ALL : loop over all devices
* ATA_DITER_ALL_REVERSE : loop over all devices in reverse order
This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds MDMA/UDMA support using BestComm for DMA on the MPC5200
platform. Based heavily on previous work by Freescale (Bernard Kuhn,
John Rigby) and Domen Puncer.
With this patch, a SanDisk Extreme IV CF card gets read speeds of
approximately 26.70 MB/sec.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
IDE hpt366 driver doesn't allow DMA for ATAPI devices and MWDMA2 on
ATAPI device locks up pata_hpt366. Follow the suit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_hpt366 is strange in that its two channels occupy two PCI
functions and both are primary channels and bit1 of PCI configuration
register 0x5A indicates cable for both channels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to miscommunication, P/N was mistaken as firmware revision
strings. Update it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some systems report SIS 5513 as both vendor/id and subvendor/id
string. In that case we can't distinguish the system by the id
svid/sdid and in fact the entry here breaks some boxes. At some
point we need to find another way to detect the Targa Visionary 1000,
until then this trades a hang for some users with lower performance
for others.
Closes: #12092
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hi,
I've found this issue in the mmotm 2008-12-02-17-08.
--
Commit
ata_piix: add borked Tecra M4 to broken suspend list
introduced DMI variables checking, but they can be null, so that
we possibly dereference null.
Check if they are null and avoid checks in that case.
Solves:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: [<ffffffff8043da97>] piix_pci_device_suspend+0x117/0x230
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
