Make the FRV arch use virtual interrupt disablement because accesses to the
processor status register (PSR) are relatively slow and because we will
soon have the need to deal with multiple interrupt controls at the same
time (separate h/w and inter-core interrupts).
The way this is done is to dedicate one of the four integer condition code
registers (ICC2) to maintaining a virtual interrupt disablement state
whilst inside the kernel. This uses the ICC2.Z flag (Zero) to indicate
whether the interrupts are virtually disabled and the ICC2.C flag (Carry)
to indicate whether the interrupts are physically disabled.
ICC2.Z is set to indicate interrupts are virtually disabled. ICC2.C is set
to indicate interrupts are physically enabled. Under normal running
conditions Z==0 and C==1.
Disabling interrupts with local_irq_disable() doesn't then actually
physically disable interrupts - it merely sets ICC2.Z to 1. Should an
interrupt then happen, the exception prologue will note ICC2.Z is set and
branch out of line using one instruction (an unlikely BEQ). Here it will
physically disable interrupts and clear ICC2.C.
When it comes time to enable interrupts (local_irq_enable()), this simply
clears the ICC2.Z flag and invokes a trap #2 if both Z and C flags are
clear (the HI integer condition). This can be done with the TIHI
conditional trap instruction.
The trap then physically reenables interrupts and sets ICC2.C again. Upon
returning the interrupt will be taken as interrupts will then be enabled.
Note that whilst processing the trap, the whole exceptions system is
disabled, and so an interrupt can't happen till it returns.
If no pending interrupt had happened, ICC2.C would still be set, the HI
condition would not be fulfilled, and no trap will happen.
Saving interrupts (local_irq_save) is simply a matter of pulling the ICC2.Z
flag out of the CCR register, shifting it down and masking it off. This
gives a result of 0 if interrupts were enabled and 1 if they weren't.
Restoring interrupts (local_irq_restore) is then a matter of taking the
saved value mentioned previously and XOR'ing it against 1. If it was one,
the result will be zero, and if it was zero the result will be non-zero.
This result is then used to affect the ICC2.Z flag directly (it is a
condition code flag after all). An XOR instruction does not affect the
Carry flag, and so that bit of state is unchanged. The two flags can then
be sampled to see if they're both zero using the trap (TIHI) as for the
unconditional reenablement (local_irq_enable).
This patch also:
(1) Modifies the debugging stub (break.S) to handle single-stepping crossing
into the trap #2 handler and into virtually disabled interrupts.
(2) Removes superseded fixup pointers from the second instructions in the trap
tables (there's no a separate fixup table for this).
(3) Declares the trap #3 vector for use in .org directives in the trap table.
(4) Moves irq_enter() and irq_exit() in do_IRQ() to avoid problems with
virtual interrupt handling, and removes the duplicate code that has now
been folded into irq_exit() (softirq and preemption handling).
(5) Tells the compiler in the arch Makefile that ICC2 is now reserved.
(6) Documents the in-kernel ABI, including the virtual interrupts.
(7) Renames the old irq management functions to different names.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Document the reset module parameter which was recently added to the
w83627hf driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updated the documentation to include the definition of the USB device
node format for Freescale SOC devices.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Documents the new feature, why it is needed, it's cost, design,
implementation, and test plan.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated SOC node definition in documentation to include bus-frequency
property. Also extended mdio example to match specification.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This resolves some minor version skew glitches that accumulated for the AVR
Butterfly adapter driver, which caused among other things the existence of
a duplicate Kconfig entry. Most of it boils down to comment updates, but in
one case it removes some now-superfluous code that would be better if not
copied into other controller-level drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Only scan I2C address 0x2d. This is the default address and no IT87xxF
chip was ever seen on I2C at a different address. These chips are
better accessed through their ISA interface anyway.
This fixes bug #5889, although it doesn't address the whole class
of problems. We'd need the ability to blacklist arbitrary I2C addresses
on systems known to contain I2C devices which behave badly when probed.
Plan the I2C interface for removal as well. If nobody complains within
a year, it will confirm my impression that the I2C interface isn't
actually needed by anyone.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is my f71805f hardware monitoring driver ported from lm_sensors
to Linux 2.6. This new driver differs from the other hardware monitoring
drivers in that it is implemented as a platform driver. This might not
be optimal yet (we would probably need a generic infrastructure and bus
type for Super-I/O logical devices) but it is certainly much better than
the i2c-isa solution.
Note that this driver requires lm_sensors CVS. I hope to get it
released as 2.10.0 soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add some documentation for the new f71805f driver. This is almost the
same help that was present in lm_sensors, with a few minor layout fixes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch just renames the documentation file to correct file name.
i2c-sis69x -> i2c-sis96x.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some broken motherboards (at least one NForce3 based AMD64 laptop)
the PIT timer runs at a incorrect frequency. This patch adds a new
option "apicpmtimer" that allows to use the APIC timer and calibrate it
using the PMTimer. It requires the earlier patch that allows to run the
main timer from the APIC.
Specifying apicpmtimer implies apicmaintimer.
The option defaults to off for now.
I tested it on a few systems and the resulting APIC timer frequencies
were usually a bit off, but always <1%, which should be tolerable.
TBD figure out heuristic to enable this automatically on the affected
systems TBD perhaps do it on all NForce3s or using DMI?
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another piece from the no-idle-tick patch.
This can be enabled with the "apicmaintimer" option.
This is mainly useful when the PIT/HPET interrupt is unreliable.
Note there are some systems that are known to stop the APIC
timer in C3. For those it will never work, but this case
should be automatically detected.
It also only works with PM timer right now. When HPET is used
the way the main timer handler computes the delay doesn't work.
It should be a bit more efficient because there is one less
regular interrupt to process on the boot processor.
Requires earlier bugfix from Venkatesh
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for 1078 type controller (device id : 0x60).
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch properly registers the 16 byte command length capability of
the megaraid_sas controlled hardware with the scsi midlayer. All
megaraid_sas hardware supports 16 byte CDB's.
Signed-off-by: Joshua Giles <joshua_giles@dell.com>
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
configfs always made item and attribute ownership root.root and
permissions based on a umask of 022. Add ->setattr() to allow
chown(2)/chmod(2), and persist the changes for the lifetime of the
items and attributes.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Update ocfs2.txt to add "cluster aware lockf" under missing features.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The patch implements cpu topology exportation by sysfs.
Items (attributes) are similar to /proc/cpuinfo.
1) /sys/devices/system/cpu/cpuX/topology/physical_package_id:
represent the physical package id of cpu X;
2) /sys/devices/system/cpu/cpuX/topology/core_id:
represent the cpu core id to cpu X;
3) /sys/devices/system/cpu/cpuX/topology/thread_siblings:
represent the thread siblings to cpu X in the same core;
4) /sys/devices/system/cpu/cpuX/topology/core_siblings:
represent the thread siblings to cpu X in the same physical package;
To implement it in an architecture-neutral way, a new source file,
driver/base/topology.c, is to export the 5 attributes.
If one architecture wants to support this feature, it just needs to
implement 4 defines, typically in file include/asm-XXX/topology.h.
The 4 defines are:
#define topology_physical_package_id(cpu)
#define topology_core_id(cpu)
#define topology_thread_siblings(cpu)
#define topology_core_siblings(cpu)
The type of **_id is int.
The type of siblings is cpumask_t.
To be consistent on all architectures, the 4 attributes should have
deafult values if their values are unavailable. Below is the rule.
1) physical_package_id: If cpu has no physical package id, -1 is the
default value.
2) core_id: If cpu doesn't support multi-core, its core id is 0.
3) thread_siblings: Just include itself, if the cpu doesn't support
HT/multi-thread.
4) core_siblings: Just include itself, if the cpu doesn't support
multi-core and HT/Multi-thread.
So be careful when declaring the 4 defines in include/asm-XXX/topology.h.
If an attribute isn't defined on an architecture, it won't be exported.
Thank Nathan, Greg, Andi, Paul and Venki.
The patch provides defines for i386/x86_64/ia64.
Signed-off-by: Zhang, Yanmin <yanmin.zhang@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix documentation to actually match the code.
Signed-off-by: Arnaud Giersch <arnaud.giersch@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is a cleanup/restructuring/clarification of the PCI error
handling doc. It should look rather professional at this point.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Edits to the driver-model documentation for grammar, clarity and content.
These docs haven't been updated in years, and some of the technical content
and discussion has become stale; this patch updates these. In addition,
some of the language is awkward. Fix this.
(I'm trying to cleanup the other files in this directory also,
patches for these will come a bit later).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Taken largely from the commit of the patch that added this feature:
1c2fb7f93c
I'm not sure about the ordering of the options in sysctl.txt,
so I took a wild guess about where it fits.
Signed-Off-By: Horms <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add info that structs, unions, enums, and typedefs are supported.
- Add doc about "private:" and "public:" tags for struct fields.
- Fix some typos.
- Remove some trailing whitespace.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates to in-tree RCU documentation based on comments over the past few
months.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add direct migration support with fall back to swap.
Direct migration support on top of the swap based page migration facility.
This allows the direct migration of anonymous pages and the migration of file
backed pages by dropping the associated buffers (requires writeout).
Fall back to swap out if necessary.
The patch is based on lots of patches from the hotplug project but the code
was restructured, documented and simplified as much as possible.
Note that an additional patch that defines the migrate_page() method for
filesystems is necessary in order to avoid writeback for anonymous and file
backed pages.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If large amounts of zone memory are used by empty slabs then zone_reclaim
becomes uneffective. This patch shakes the slab a bit.
The problem with this patch is that the slab reclaim is not containable to a
zone. Thus slab reclaim may affect the whole system and be extremely slow.
This also means that we cannot determine how many pages were freed in this
zone. Thus we need to go off node for at least one allocation.
The functionality is disabled by default.
We could modify the shrinkers to take a zone parameter but that would be quite
invasive. Better ideas are welcome.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some situations one may want zone_reclaim to behave differently. For
example a process writing large amounts of memory will spew unto other nodes
to cache the writes if many pages in a zone become dirty. This may impact the
performance of processes running on other nodes.
Allowing writes during reclaim puts a stop to that behavior and throttles the
process by restricting the pages to the local zone.
Similarly one may want to contain processes to local memory by enabling
regular swap behavior during zone_reclaim. Off node memory allocation can
then be controlled through memory policies and cpusets.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the zone_reclaim code has a fixed window of 30 seconds of off node
allocations should a local zone have no unused pagecache pages left. Reclaim
will be attempted again after this timeout period to avoid repeated useless
scans for memory. This is also useful to established sufficiently large off
node allocation chunks to relieve the local node.
It may be beneficial to adjust that time period for some special situations.
For example if memory use was exceeding node capacity one may want to give up
for longer periods of time. If memory spikes intermittendly then one may want
to shorten the time period to reduce the number of off node allocations.
This patch allows just that....
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The flattened device tree is the only supported way of booting ARCH=powerpc
kernels on non Open Firmware machines. The documentation for the flattened
tree format and contents has been discussed on mailing lists and lately has
been living in the dtc git tree. Really, it ought to go in the kernel's
Documentation directory for maximum visibility.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make swsusp use bytes as the image size units, which is needed for future
compatibility.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_LEGACY_PROC is deprecated since 2.5.53 in favor of lspci(8).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- the w9968cf-vpp module is not intended for inclusion into the kernel
- the upstream w9968cf package shipping the w9968cf-vpp module suggests
to simply replace the w9968cf module shipped with the kernel
Therefore, there seems to be no good reason spending some bytes of
kernel memory for hooks for the w9968cf-vpp module.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a Video4Linux2 driver giving support
to ET61X151 and ET61X251 PC Camera Controllers made by
Etoms Electronics.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates:
- Use kzalloc() instead of kmalloc()
- Move some macro definitions from sn9c102.h to sn9c102_core.c
- Use vfree() and vmalloc_32() instead of rvfree() and rvmalloc()
- Fix mmap() sys call
- Documentation updates
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates and bugfixes.
Changes: + new, - removed, * cleanup, @ bugfix:
@ fix poll()
@ Remove bad get_ctrl()'s
* Reduce ioctl stack usage
* Remove final ";" from some macro definitions
* Better support for SN9C103
+ Add sn9c102_write_regs()
+ Add 0x0c45/0x602d to the list of SN9C10x based devices
+ Add support for OV7630 image sensors
+ Provide support for the built-in microphone interface of the SN9C103
+ Documentation updates
+ Add 0x0c45/0x602e to the list of SN9C10x based devices
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
