Use generic_handle_irq() to handle mixed-type irq handling.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
`typename' is going away and is usually uninitialised anwyay.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When called to do a transfer that has a start offset within the cache
line which is uneven between source and destination and a length which
terminates the source of the copy exactly on a cache line, one extra
line gets copied into a temporary buffer. This is normally not an issue
since the buffer is a kernel buffer and only the requested information
gets copied into the user buffer.
The problem arises when the source ends at the very last physical page
of memory. That last cache line does not exist and results in the SHUB
chip raising an MCA.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
(David:)
If hugetlbfs_file_mmap() returns a failure to do_mmap_pgoff() - for example,
because the given file offset is not hugepage aligned - then do_mmap_pgoff
will go to the unmap_and_free_vma backout path.
But at this stage the vma hasn't been marked as hugepage, and the backout path
will call unmap_region() on it. That will eventually call down to the
non-hugepage version of unmap_page_range(). On ppc64, at least, that will
cause serious problems if there are any existing hugepage pagetable entries in
the vicinity - for example if there are any other hugepage mappings under the
same PUD. unmap_page_range() will trigger a bad_pud() on the hugepage pud
entries. I suspect this will also cause bad problems on ia64, though I don't
have a machine to test it on.
(Hugh:)
prepare_hugepage_range() should check file offset alignment when it checks
virtual address and length, to stop MAP_FIXED with a bad huge offset from
unmapping before it fails further down. PowerPC should apply the same
prepare_hugepage_range alignment checks as ia64 and all the others do.
Then none of the alignment checks in hugetlbfs_file_mmap are required (nor
is the check for too small a mapping); but even so, move up setting of
VM_HUGETLB and add a comment to warn of what David Gibson discovered - if
hugetlbfs_file_mmap fails before setting it, do_mmap_pgoff's unmap_region
when unwinding from error will go the non-huge way, which may cause bad
behaviour on architectures (powerpc and ia64) which segregate their huge
mappings into a separate region of the address space.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Adam Litke <agl@us.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix MSPEC driver to build for non SN2 enabled configs as the driver should
work in cached and uncached modes (no fetchop) on these systems. In
addition make MSPEC select IA64_UNCACHED_ALLOCATOR, which is required for
it and move it to arch/ia64/Kconfig to avoid warnings on non ia64
architectures running allmodconfig. Once the Kconfig code is fixed, we can
move it back.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Cc: Fernando Luis Vzquez Cao <fernando@oss.ntt.co.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When ACPI && NUMA, pxm_to_node is used and it exists in drivers/acpi/numa.c
Tony said:
The patch makes sense ... if you pick both of "ACPI" and "NUMA", then you
need (and should automatically be given) ACPI_NUMA too.
The only open question is whether there is a better way of getting there.
Perhaps with less configuration options in the first place? We are heading
towards a future where so many systems will be NUMA that there would seem to
be little benefit in keeping ACPI_NUMA separate from ACPI ... but perhaps
we aren't quite there yet.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of master.kernel.org:/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Correct definition of handle_IPI
[IA64] move SAL_CACHE_FLUSH check later in boot
[IA64] MCA recovery: Montecito support
[IA64] cpu-hotplug: Fixing confliction between CPU hot-add and IPI
[IA64] don't double >> PAGE_SHIFT pointer for /dev/kmem access
The declaration of handle_IPI in arch/ia64/kernel/smp.c was changed but
not the definition of this function. Remove struct pt_regs from
handle_IPI().
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The check to see if the firmware drops interrupts during a
SAL_CACHE_FLUSH is done to early in the boot. SAL_CACHE_FLUSH expects
to be able to make PAL calls in virtual mode, on some cell based
machines a fault occurs causing a MCA. This patch moves the check
after mmu_context_init so the TLB and VHPT are properly setup.
Signed-off-by Troy Heber <troy.heber@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The information in MCA records is filled in slightly differently on
Montecito than on Madison/McKinley. Usually, the cache check and bus
check target identifiers have the same address. On Montecito the
cache check and bus check target identifiers can be different if
a corrected error (ie SBE or unconsumed poison data) was encountered and
then an uncorrected error (ie DBE) was consumed. In that case, the
cache check target identifier is the physical address of the DBE (that
caused the MCA to surface) while the bus check target identifier is the
physical address of the SBE. This patch correctly finds the target
identifier that triggered the MCA.
If there are multiple valid cache target identifiers in the same
error record then use the one with the lowest cache level.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Remove quirk_via_abnormal_poweroff
PCI: reset pci device state to unknown state for resume
PCI: x86-64: mmconfig missing printk levels
PCI: fix pci_fixup_video as it blows up on sparc64
acpiphp: fix latch status
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table,
teach all the architectures to use it.
This is a prerequisite for a patch which performs initcall synchronisation for
multithreaded-probing.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Added AVR32 as well ]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts much of the original pci_fixup_video change and makes it
work for all arches that need it.
fixed, and tested on x86, x86_64 and IA64 dig.
Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Count the number of "resched" interrupts that each cpu receives.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The current sn2_defconfig is obsolete, in particular the recent ATA
changes are a pain, so here's a patch to get things in sync ... at
least for a day or two :)
Update sn_defconfig to match current community kernel tree.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reformat to fit in 80 columns. Fix a couple typos. Remove
a couple unused labels.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Linux maps PAL instructions with an ITR, but uses a DTC for PAL data.
Section 11.10.2.1.3, "Making PAL Procedures Calls in Physical or Virtual
Mode," of the SDM (rev 2.2), says we must therefore make all PAL calls
with PSR.ic = 1 so that Linux can handle any TLB faults.
PAL_CALL_IC_OFF is currently unused, and as long as we use the ITR + DTC
strategy, we can't use it. So remove it. I also removed the code in
ia64_pal_call_static() that conditionally cleared PSR.ic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Allow pending IPIs to interrupt a timer interrupt that is looping
in the do_timer() "while" loop in timer_interrupt(). (Interrupts are
allowed at only 1 spot in the code).
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Missed one piece of ia64 fallout from the global IRQ patch
7d12e780e0
Perfmon interrupt handler needs to use get_irq_regs() too.
Acked-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Arch-independent zone-sizing is using indices instead of symbolic names to
offset within an array related to zones (max_zone_pfns). The unintended
impact is that ZONE_DMA and ZONE_NORMAL is initialised on powerpc instead
of ZONE_DMA and ZONE_HIGHMEM when CONFIG_HIGHMEM is set. As a result, the
the machine fails to boot but will boot with CONFIG_HIGHMEM turned off.
The following patch properly initialises the max_zone_pfns[] array and uses
symbolic names instead of indices in each architecture using
arch-independent zone-sizing. Two users have successfully booted their
powerpcs with it (one an ibook G4). It has also been boot tested on x86,
x86_64, ppc64 and ia64. Please merge for 2.6.19-rc2.
Credit to Benjamin Herrenschmidt for identifying the bug and rolling the
first fix. Additional credit to Johannes Berg and Andreas Schwab for
reporting the problem and testing on powerpc.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cast to (void *) in request_irq() argument is stupid and
only hides problems...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time. This was scripted with the
following small shell script:
#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* |
while read i
do
echo $i
perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: David Howells <dhowells@redhat.com>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This is just a few makefile tweaks and some file renames.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we attempt to predict how many irqs we will be able to allocate with
msi using pci_vector_resources and some complicated accounting, and then we
only allow each device as many irqs as we think are available on average.
Only the s2io driver even takes advantage of this feature all other drivers
have a fixed number of irqs they need and bail if they can't get them.
pci_vector_resources is inaccurate if anyone ever frees an irq. The whole
implmentation is racy. The current irq limit policy does not appear to make
sense with current drivers. So I have simplified things. We can revisit this
we we need a more sophisticated policy.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The patch below corrects multiple occurances of "the the"
typos across several files, both in source comments and KConfig files.
There is no actual code changed, only text. Note this only affects the /arch
directory, and I believe I could find many more elsewhere. :)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
These patches make the kernel pass 64-bit inode numbers internally when
communicating to userspace, even on a 32-bit system. They are required
because some filesystems have intrinsic 64-bit inode numbers: NFS3+ and XFS
for example. The 64-bit inode numbers are then propagated to userspace
automatically where the arch supports it.
Problems have been seen with userspace (eg: ld.so) using the 64-bit inode
number returned by stat64() or getdents64() to differentiate files, and
failing because the 64-bit inode number space was compressed to 32-bits, and
so overlaps occur.
This patch:
Make filldir_t take a 64-bit inode number and struct kstat carry a 64-bit
inode number so that 64-bit inode numbers can be passed back to userspace.
The stat functions then returns the full 64-bit inode number where
available and where possible. If it is not possible to represent the inode
number supplied by the filesystem in the field provided by userspace, then
error EOVERFLOW will be issued.
Similarly, the getdents/readdir functions now pass the full 64-bit inode
number to userspace where possible, returning EOVERFLOW instead when a
directory entry is encountered that can't be properly represented.
Note that this means that some inodes will not be stat'able on a 32-bit
system with old libraries where they were before - but it does mean that
there will be no ambiguity over what a 32-bit inode number refers to.
Note similarly that directory scans may be cut short with an error on a
32-bit system with old libraries where the scan would work before for the
same reasons.
It is judged unlikely that this situation will occur because modern glibc
uses 64-bit capable versions of stat and getdents class functions
exclusively, and that older systems are unlikely to encounter
unrepresentable inode numbers anyway.
[akpm: alpha build fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last in-kernel user of errno is gone, so we should remove the definition
and everything referring to it. This also removes the now-unused lib/execve.c
file that was introduced earlier.
Also remove every trace of __KERNEL_SYSCALLS__ that still remained in the
kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some architectures provide an execve function that does not set errno, but
instead returns the result code directly. Rename these to kernel_execve to
get the right semantics there. Moreover, there is no reasone for any of these
architectures to still provide __KERNEL_SYSCALLS__ or _syscallN macros, so
remove these right away.
[akpm@osdl.org: build fix]
[bunk@stusta.de: build fix]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace references to system_utsname to the per-process uts namespace
where appropriate. This includes things like uname.
Changes: Per Eric Biederman's comments, use the per-process uts namespace
for ELF_PLATFORM, sunrpc, and parts of net/ipv4/ipconfig.c
[jdike@addtoit.com: UML fix]
[clg@fr.ibm.com: cleanup]
[akpm@osdl.org: build fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the init_nsproxy definition out of arch/ into kernel/nsproxy.c. This
avoids all arches having to be updated. Compiles and boots on s390.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a nsproxy structure to the task struct. Later patches will
move the fs namespace pointer into this structure, and introduce a new utsname
namespace into the nsproxy.
The vserver and openvz functionality, then, would be implemented in large part
by virtualizing/isolating more and more resources into namespaces, each
contained in the nsproxy.
[akpm@osdl.org: build fix]
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpumask: ensure that node_to_cpumask() is available to modules for all
supported combinations of architecture and CONFIG_NUMA.
Signed-off-by: Greg Banks <gnb@melbourne.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kprobe_flush_task() possibly calls kfree function during holding
kretprobe_lock spinlock, if kfree function is probed by kretprobe that will
incur spinlock deadlock. This patch moves kfree function out scope of
kretprobe_lock.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whitespace is used to indent, this patch cleans up these sentences by
kernel coding style.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In an effort to make kprobe modules more portable, here is a patch that:
o Introduces the "symbol_name" field to struct kprobe.
The symbol->address resolution now happens in the kernel in an
architecture agnostic manner. 64-bit powerpc users no longer have
to specify the ".symbols"
o Introduces the "offset" field to struct kprobe to allow a user to
specify an offset into a symbol.
o The legacy mechanism of specifying the kprobe.addr is still supported.
However, if both the kprobe.addr and kprobe.symbol_name are specified,
probe registration fails with an -EINVAL.
o The symbol resolution code uses kallsyms_lookup_name(). So
CONFIG_KPROBES now depends on CONFIG_KALLSYMS
o Apparantly kprobe modules were the only legitimate out-of-tree user of
the kallsyms_lookup_name() EXPORT. Now that the symbol resolution
happens in-kernel, remove the EXPORT as suggested by Christoph Hellwig
o Modify tcp_probe.c that uses the kprobe interface so as to make it
work on multiple platforms (in its earlier form, the code wouldn't
work, say, on powerpc)
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking. One of these
structures was a struct tty_operations. In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.
This patch declares all struct tty_operations in the tree as const. In all
cases, they are static and used only as input to tty_set_operations. As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.
53 drivers are affected. I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months. serial_core.c was the busiest one that I looked at.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
asm/serial.h is supposed to contain the definitions for the architecture
specific 8250 ports for the 8250 driver. It may also define BASE_BAUD,
but this is the base baud for the architecture specific ports _only_.
Therefore, nothing other than the 8250 driver should be including this
header file. In order to move towards this goal, here is a patch which
removes some of the more obvious incorrect includes of the file.
Acked-by: Paul Fulghum <paulkf@microgate.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With 2.6.18-rc4-mm2, now wall_jiffies will always be the same as jiffies.
So we can kill wall_jiffies completely.
This is just a cleanup and logically should not change any real behavior
except for one thing: RTC updating code in (old) ppc and xtensa use a
condition "jiffies - wall_jiffies == 1". This condition is never met so I
suppose it is just a bug. I just remove that condition only instead of
kill the whole "if" block.
[heiko.carstens@de.ibm.com: s390 build fix and cleanup]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In cases where the acpi memory-add event does not containe the pxm (node)
infomation allow the driver to look up node info based on the address. The
acpi_get_node call returns -1 if it can't decode the pxm info, this causes
add_memory to panic. acpi_get_node would have to decode the resource from the
handle (a lenghty proposition). This seems to be the cleanist point to
interject the hook.
[kamezawa.hiroyu@jp.fujitsu.com: build fixes]
[y-goto@jp.fujitsu.com: build fixes]
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass ticks to do_timer() and update_times(), and adjust x86_64 and s390
timer interrupt handler with this change.
Currently update_times() calculates ticks by "jiffies - wall_jiffies", but
callers of do_timer() should know how many ticks to update. Passing ticks
get rid of this redundant calculation. Also there are another redundancy
pointed out by Martin Schwidefsky.
This cleanup make a barrier added by
5aee405c66 needless. So this patch removes
it.
As a bonus, this cleanup make wall_jiffies can be removed easily, since now
wall_jiffies is always synced with jiffies. (This patch does not really
remove wall_jiffies. It would be another cleanup patch)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is an updated version of Eric Biederman's is_init() patch.
(http://lkml.org/lkml/2006/2/6/280). It applies cleanly to 2.6.18-rc3 and
replaces a few more instances of ->pid == 1 with is_init().
Further, is_init() checks pid and thus removes dependency on Eric's other
patches for now.
Eric's original description:
There are a lot of places in the kernel where we test for init
because we give it special properties. Most significantly init
must not die. This results in code all over the kernel test
->pid == 1.
Introduce is_init to capture this case.
With multiple pid spaces for all of the cases affected we are
looking for only the first process on the system, not some other
process that has pid == 1.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: <lxc-devel@lists.sourceforge.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make PROT_WRITE imply PROT_READ for a number of architectures which don't
support write only in hardware.
While looking at this, I noticed that some architectures which do not
support write only mappings already take the exact same approach. For
example, in arch/alpha/mm/fault.c:
"
if (cause < 0) {
if (!(vma->vm_flags & VM_EXEC))
goto bad_area;
} else if (!cause) {
/* Allow reads even for write-only mappings */
if (!(vma->vm_flags & (VM_READ | VM_WRITE)))
goto bad_area;
} else {
if (!(vma->vm_flags & VM_WRITE))
goto bad_area;
}
"
Thus, this patch brings other architectures which do not support write only
mappings in-line and consistent with the rest. I've verified the patch on
ia64, x86_64 and x86.
Additional discussion:
Several architectures, including x86, can not support write-only mappings.
The pte for x86 reserves a single bit for protection and its two states are
read only or read/write. Thus, write only is not supported in h/w.
Currently, if i 'mmap' a page write-only, the first read attempt on that page
creates a page fault and will SEGV. That check is enforced in
arch/blah/mm/fault.c. However, if i first write that page it will fault in
and the pte will be set to read/write. Thus, any subsequent reads to the page
will succeed. It is this inconsistency in behavior that this patch is
attempting to address. Furthermore, if the page is swapped out, and then
brought back the first read will also cause a SEGV. Thus, any arbitrary read
on a page can potentially result in a SEGV.
According to the SuSv3 spec, "if the application requests only PROT_WRITE, the
implementation may also allow read access." Also as mentioned, some
archtectures, such as alpha, shown above already take the approach that i am
suggesting.
The counter-argument to this raised by Arjan, is that the kernel is enforcing
the write only mapping the best it can given the h/w limitations. This is
true, however Alan Cox, and myself would argue that the inconsitency in
behavior, that is applications can sometimes work/sometimes fails is highly
undesireable. If you read through the thread, i think people, came to an
agreement on the last patch i posted, as nobody has objected to it...
Signed-off-by: Jason Baron <jbaron@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ifa_local, ifa_address, ifa_mask, ifa_broadcast and ifa_anycast are
net-endian. Annotated them and variables that are inferred to be
net-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] minor reformatting to vmlinux.lds.S
[IA64] CMC/CPE: Reverse the order of fetching log and checking poll threshold
[IA64] PAL calls need physical mode, stacked
[IA64] ar.fpsr not set on MCA/INIT kernel entry
[IA64] printing support for MCA/INIT
[IA64] trim output of show_mem()
[IA64] show_mem() printk levels
[IA64] Make gp value point to Region 5 in mca handler
Revert "[IA64] Unwire set/get_robust_list"
[IA64] Implement futex primitives
[IA64-SGI] Do not request DMA memory for BTE
[IA64] Move perfmon tables from thread_struct to pfm_context
[IA64] Add interface so modules can discover whether multithreading is on.
[IA64] kprobes: fixup the pagefault exception caused by probehandlers
[IA64] kprobe opcode 16 bytes alignment on IA64
[IA64] esi-support
[IA64] Add "model name" to /proc/cpuinfo
Since sys_sysctl is deprecated start allow it to be compiled out. This
should catch any remaining user space code that cares, and paves the way
for further sysctl cleanups.
[akpm@osdl.org: If sys_sysctl() is not compiled-in, emit a warning]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix build error introduced by 3212fe1594
Non-NUMA case should be handled.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch prevents pcibios_disable_device() from disabling interrupts
of devices which is not enabled.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor reformatting to vmlinux.lds.S to make it 80-column usable,
in accordance with Linux coding style.
Signed-off-by: Al Stone <ahs3@fc.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch reverses the order of fetching log from SAL and
checking poll threshold. This will fix following trivial issues:
- If SAL_GET_SATE_INFO is unbelievably slow (due to huge system
or just its silly implementation) and if it takes more than
1/5 sec, CMCI/CPEI will never switch to CMCP/CPEP.
- Assuming terrible flood of interrupt (continuous corrected
errors let all CPUs enter to handler at once and bind them
in it), CPUs will be serialized by IA64_LOG_LOCK(*).
Now we check the poll threshold after the lock and log fetch,
so we need to call SAL_GET_STATE_INFO (num_online_cpus() + 4)
times in the worst case.
if we can check the threshold before the lock, we can shut up
interrupts quickly without waiting preceding log fetches, and
the number of times will be reduced to (num_online_cpus()) in
the same situation.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When entering the kernel due to an MCA or INIT, ar.fpsr (ar40)
was not getting set to the kernel default value (remaining
at the user value). The effect depends on the user setting
of ar.fpsr. In the test case, the effect was addresses
printing with strange hex values.
Setting ar.fpsr in ia64_set_kernel_registers sets it for both
the MCA and INIT paths. The user value of ar.fpsr is correctly
saved (in ia64_state_save) and restored (in ia64_state_restore).
Below is an example of output with very strange hex values.
Anyone know the value of hex 'g'? :-)
Processes interrupted by INIT - 0 (cpu 14 task 0xdfffg55g7a4c6gA)
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Printing message to console from MCA/INIT handler is useful,
however doing oops_in_progress = 1 in them exactly makes
something in kernel wrong. Especially it sounds ugly if
system goes wrong after returning from recoverable MCA.
This patch adds ia64_mca_printk() function that collects
messages into temporary-not-so-large message buffer during
in MCA/INIT environment and print them out later, after
returning to normal context or when handlers determine to
down the system.
Also this print function is exported for use in extensional
MCA handler. It would be useful to describe detail about
recovery.
NOTE:
I don't think it is sane thing if temporary message buffer
is enlarged enough to hold whole stack dumps from INIT, so
buffering is disabled during stack dump from INIT-monarch
(= default_monarch_init_process). please fix it in future.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cut the number of lines of memory info output per node from five
to one line.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use the default sysrq printk level for printing show_mem() output both
for disconfig and contig versions. This is consistent with the printk
level used on other architectures (well ia32 at least).
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
MCA dispatch code take physical address of GP passed from SAL, then call
DATA_PA_TO_VA twice on GP before call into C code. The first time is
in ia64_set_kernel_register, the second time is in VIRTUAL_MODE_ENTER.
The gp is changed to a virtual address in region 7 because DATA_PA_TO_VA
is implemented by dep instruction.
However when notify blocks were called from MCA handler code, because
notify blocks are supported by callback function pointers, gp value
value was switched to region 5 again.
The patch set gp register to kernel gp of region 5 at entry of MCA
dispatch.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This reverts commit 2636255488.
Jakub Jelinek provided the missing futex_atomic_cmpxchg_inatomic()
function, so now it should be safe to re-enable these syscalls.
Signed-off-by: Tony Luck <tony.luck@intel.com>
The GFP_DMA option usually does nothing on SN2 since all of memory is in thei
DMA zone and the BTE has always been capable of addressing all of memory.
So there is no need to get memory from a restricted range of memory (which
is what GFP_DMA is for).
Remove useless __GFP_DMA option.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch renders thread_struct->pmcs[] and thread_struct->pmds[]
OBSOLETE. The actual table is moved to pfm_context structure which
saves space in thread_struct (in turn saving space in task_struct
which frees up more space for kernel stacks).
Signed-off-by: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add is_multithreading_enabled() to check whether multi-threading
is enabled independently of which cpu is currently online
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If the user-specified kprobe handler causes the page fault when accessing
user space address, fixup this fault since do_page_fault() should not
continue as the kprobe handler are run with preemption disabled.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On IA64 instruction opcode must be 16 bytes alignment, in kprobe structure
there is one element to save original instruction, currently saved opcode
is not statically allocated in kprobe structure, that can not assure
16 bytes alignment. This patch dynamically allocated kprobe instruction
opcode to assure 16 bytes alignment.
Signed-off-by: bibo mao <bibo.mao@intel.com>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If we're going to implement smp_call_function_single() on three architecture
with the same prototype then it should have a declaration in a
non-arch-specific header file.
Move it into <linux/smp.h>.
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In many places we will need to use the same combination of flags. Specify
a single GFP_THISNODE definition for ease of use in gfp.h.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The uncached allocator manages per node pools. Specify __GFP_THISNODE in
order to force allocation on the indicated node or fail. The uncached
allocator has already logic to deal with failing allocations.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make ZONE_DMA32 optional
- Add #ifdefs around ZONE_DMA32 specific code and definitions.
- Add CONFIG_ZONE_DMA32 config option and use that for x86_64
that alone needs this zone.
- Remove the use of CONFIG_DMA_IS_DMA32 and CONFIG_DMA_IS_NORMAL
for ia64 and fix up the way per node ZVCs are calculated.
- Fall back to prior GFP_ZONEMASK of 0x03 if there is no
DMA32 zone.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Assume that a cpu is *physically* offlined at boot time...
Because smpboot.c::smp_boot_cpu_map() canoot find cpu's sapicid,
numa.c::build_cpu_to_node_map() cannot build cpu<->node map for
offlined cpu.
For such cpus, cpu_to_node map should be fixed at cpu-hot-add.
This mapping should be done before cpu onlining.
This patch also handles cpu hotremove case.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Problem description:
We have additional_cpus= option for allocating possible_cpus. But nid
for possible cpus are not fixed at boot time. cpus which is offlined at
boot or cpus which is not on SRAT is not tied to its node. This will
cause panic at cpu onlining.
Usually, pxm_to_nid() mapping is fixed at boot time by SRAT.
But, unfortunately, some system (my system!) do not include
full SRAT table for possible cpus. (Then, I use
additiona_cpus= option.)
For such possible cpus, pxm<->nid should be fixed at
hot-add. We now have acpi_map_pxm_to_node() which is also
used at boot. It's suitable here.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Take default arch/*/kernel/audit.c to lib/, have those with special
needs (== biarch) define AUDIT_ARCH in their Kconfig.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The sn_cpu_init() is required for cpu initialization on SN platforms.
Change __init to __cpuinit so that the function is not freed with init code/data.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SN PROM uses the register stack in the slave loop. The contents
must be preserved for the OS to return to the slave loop via offlining
a cpu or for kexec. A 'flushrs" is needed to force the stack to be written
to memory prior to changing bspstore.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The syscalls set/get_robust_list must not be wired up until
futex_atomic_cmpxchg_inatomic is implemented. Otherwise the kernel will
hang in handle_futex_death.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix a bug in sys_perfmonctl() whereby it was not correctly
decrementing the file descriptor reference count.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This prevents cross-region mappings on IA64 and SPARC which could lead
to system crash. They were correctly trapped for normal mmap() calls,
but not for the kernel internal calls generated by executable loading.
This code just moves the architecture-specific cross-region checks into
an arch-specific "arch_mmap_check()" macro, and defines that for the
architectures that needed it (ia64, sparc and sparc64).
Architectures that don't have any special requirements can just ignore
the new cross-region check, since the mmap() code will just notice on
its own when the macro isn't defined.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Cleaned up to not affect architectures that don't need it ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Increase default nodes shift to 10, nr_cpus to 1024
[IA64] remove redundant local_irq_save() calls from sn_sal.h
[IA64] panic if topology_init kzalloc fails
[IA64-SGI] Silent data corruption caused by XPC V2.
Change both the NODES_SHIFT and the NR_CPUS so that even big machines
can boot all nodes and processors with a generic kernel.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There really is no sense trying to continue if the kzalloc of sysfs_cpus[]
fails in ia64 topology_init. The code calling into here doesn't check
errors very well, and one ends up with a nonobvious boot failure that
wastes peoples time debugging.
See for example the lkml thread at:
http://lkml.org/lkml/2006/3/2/215
Since the system is totally dead when this kzalloc fails, not having yet
even booted, might as well announce one's death boldly and plainly.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ACPI 3.0 appended a variable length UID string to the LAPIC structure
as part of support for > 256 processors. So the BAD_MADT_ENTRY() sanity
check can no longer compare for equality with a fixed structure length.
Signed-off-by: Alexey Y Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously the message was "Fatal exception: panic_on_oops", as introduced
in a recent patch whith removed a somewhat dangerous call to ssleep() in
the panic_on_oops path. However, Paul Mackerras suggested that this was
somewhat confusing, leadind people to believe that it was panic_on_oops
that was the root cause of the fatal exception. On his suggestion, this
patch changes the message to simply "Fatal exception". A suitable oops
message should already have been displayed.
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jack Steiner identified a problem where XPC can cause a silent
data corruption. On module load, the placement may cause the
xpc_remote_copy_buffer to span two physical pages. DMA transfers are
done to the start virtual address translated to physical.
This patch changes the buffer from a statically allocated buffer to a
kmalloc'd buffer. Dean Nelson reviewed this before posting. I have
tested it in the configuration that was showing the memory corruption
and verified it works. I also added a BUG_ON statement to help catch
this if a similar situation is encountered.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Conflicts:
arch/ia64/hp/sim/simscsi.c
Stylistic differences in two separate fixes for buffer->request_buffer
problem.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The uncached allocator has a function, uncached_get_new_chunk(), that needs
to be serialized on a per node basis. It also has a global variable,
allocated_granules, which should be defined on a per node basis and protected
by that serialization. Additionally, all error returns from functions called
(like ia64_pal_mc_drain()) should be handled appropriately.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Acked-by: Jes Sorenson <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
contig.c (FLATMEM) requires the same optimization as in discontig.c for show_mem
when VIRTUAL_MEM_MAP is in use. Otherwise FLATMEM has softlockup timeouts.
This was boot tested for memory configuration: SPARSEMEM,
DISCONTIG+VIRTUAL_MEM_MAP, FLATMEM, FLATMEM+VIRTUAL_MEM_MAP and
FLATMEM+VIRTUAL_MEM_MAP with largest memory gap less than LARGE_GAP by
using boot parameter "mem=".
This was boot tested and "echo m >/proc/sysrq-trigger" output evaluated for
: FLATMEM, FLATMEM+VIRTUAL_MEM_MAP, DISCONTIGMEM+VIRTUAL_MEM_MAP and
SPARSEMEM.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Assure that vmem_map's high endpoint is MAX_ORDER aligned. Not doing so violates
the buddy allocator algorithm. Also anyone using mem=XXX on boot line and
not aligned to MAX_ORDER requires this patch in order to satisfy buddy
allocator. vmem_map always starts at pfn 0. The potentially large MAX_ORDER
on ia64 (due to hugetlbfs) requires that the end of vmem_map be aligned
to MAX_ORDER_NR_PAGES.
This was boot tested for: FLATMEM, FLATMEM+VIRTUAL_MEM_MAP,
DISCONTIGMEM+VIRTUAL_MEM_MAP and SPARSEMEM.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
CONFIG_MD_RAID5 became CONFIG_MD_RAID456 in drivers/md/Kconfig. Make
the same change in arch/ia64
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Aron Griffis <aron@hp.com>
Acked-by: Jes Sorenson <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I think ia64_switch_mode_phys and ia64_switch_mode_virt
does not need to alloc an empty frame.
An empty frame is required by loadrs but flushrs
does not need that.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We found an issue in pal.S.
According to the software runtime SPEC,
The caller's output registers do not need to be preserved for
caller. The callee may reuse input registers for any other
purpose within the procedure.
in ia64_pal_call_phys_stacked,
input registers are copied to output registers before call
into ia64_switch_mode_phys, then used to call into PAL. This
assumes output registers are preserved in ia64_switch_mode_phys,
which may not be true.
In this particular case, ia64_switch_mode_phys alloc a null frame
, and mask off psr.i.
If an interrupt comes at this small window,
or an MCA comes inside the procedure, output registers
maybe changed,
then the pal call may got some staled input registers.
This patch moves the copies from input to output
after ia64_switch_mode_phys to follow the software
runtime convention.
It also removed some unused labels in
ia64_pal_call_phys_stacked.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix some sparse warnings on ia64. Large constants that should be long
instead of int. Use NULL instead of 0. Add some missing __iomem
casts. Replace a non-C99 structure assignment.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The latest toolchains can produce a new ELF section in DSOs and
dynamically-linked executables. The new section ".gnu.hash" replaces
".hash", and allows for more efficient runtime symbol lookups by the
dynamic linker. The new ld option --hash-style={sysv|gnu|both} controls
whether to produce the old ".hash", the new ".gnu.hash", or both. In some
new systems such as Fedora Core 6, gcc by default passes --hash-style=gnu
to the linker, so that a standard invocation of "gcc -shared" results in
producing a DSO with only ".gnu.hash". The new ".gnu.hash" sections need
to be dealt with the same way as ".hash" sections in all respects; only the
dynamic linker cares about their contents. To work with older dynamic
linkers (i.e. preexisting releases of glibc), a binary must have the old
".hash" section. The --hash-style=both option produces binaries that a new
dynamic linker can use more efficiently, but an old dynamic linker can
still handle.
The new section runs afoul of the custom linker scripts used to build vDSO
images for the kernel. On ia64, the failure mode for this is a boot-time
panic because the vDSO's PT_IA_64_UNWIND segment winds up ill-formed.
This patch addresses the problem in two ways.
First, it mentions ".gnu.hash" in all the linker scripts alongside ".hash".
This produces correct vDSO images with --hash-style=sysv (or old tools),
with --hash-style=gnu, or with --hash-style=both.
Second, it passes the --hash-style=sysv option when building the vDSO
images, so that ".gnu.hash" is not actually produced. This is the most
conservative choice for compatibility with any old userland. There is some
concern that some ancient glibc builds (though not any known old production
system) might choke on --hash-style=both binaries. The optimizations
provided by the new style of hash section do not really matter for a DSO
with a tiny number of symbols, as the vDSO has. If someone wants to use
=gnu or =both for their vDSO builds and worry less about that
compatibility, just change the option and the linker script changes will
make any choice work fine.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SGI IOC4 IDE device always shares an interrupt with other devices which
are part of IOC4. As such, IDEPCI_SHARE_IRQ should always be enabled when
BLK_DEV_SGIIOC4 is enabled.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use hotplug version of register_cpu_notifier in late init functions.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is part of an effort to unify the panic_on_oops behaviour across
all architectures that implement it.
It was pointed out to me by Andi Kleen that if an oops has occured in
interrupt context, then calling sleep() in the oops path will only cause a
panic, and that it would be really better for it not to be in the path at
all.
This patch removes the ssleep() call and reworks the console message
accordinly. I have a slght concern that the resulting console message is
too long, feedback welcome.
For powerpc it also unifies the 32bit and 64bit behaviour.
Fror x86_64, this patch only updates the console message, as ssleep() is
already not present.
Signed-off-by: Horms <horms@verge.net.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kprobe inserts breakpoint instruction in probepoint and then jumps to
instruction slot when breakpoint is hit, the instruction slot icache must
be consistent with dcache. Here is the patch which invalidates instruction
slot icache area.
Without this patch, in some machines there will be fault when executing
instruction slot where icache content is inconsistent with dcache.
Signed-off-by: bibo,mao <bibo.mao@intel.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Acked-by: Keshavamurthy Anil S <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/ia64/hp/sim/simscsi.c: In function `simscsi_sg_readwrite':
arch/ia64/hp/sim/simscsi.c:154: error: structure has no member named `buffer'
arch/ia64/hp/sim/simscsi.c: In function `simscsi_fillresult':
arch/ia64/hp/sim/simscsi.c:247: error: structure has no member named `buffer'
hch said:
>Just change it to access the request_buffer member instead. buffer
>and request_buffer have been synonymous 99% of the time, and a driver
>never even wants to access buffer.
Signed-off-by: Tony Luck <tony.luck@intel.com>
/proc/pal/*/version_info is a bit confusing. HP firmware, at least,
reports 07.31 instead of 0.7.31. Also, the comment is out of place;
it's an internal detail about the implementation of ia64_pal_version.
Since the 2.2 revision of the SDM still states that PAL_VERSION can
be called in virtual mode, correct the comment to be more accurate.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On Thu, Jul 27, 2006 at 01:03:24AM -0700, Andrew Morton wrote:
> arch/ia64/hp/sim/simscsi.c: In function `simscsi_sg_readwrite':
> arch/ia64/hp/sim/simscsi.c:154: error: structure has no member named `buffer'
> arch/ia64/hp/sim/simscsi.c: In function `simscsi_fillresult':
> arch/ia64/hp/sim/simscsi.c:247: error: structure has no member named `buffer'
> arch/ia64/hp/sim/simscsi.c: At top level:
> arch/ia64/hp/sim/simscsi.c:87: warning: 'simscsi_setup' defined but not used
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Newer ARMs have a 40 bit physical address space, but mapping physical
memory above 4G needs a special page table format which we (currently?) do
not use for userspace mappings, so what happens instead is that mapping an
address >= 4G will happily discard the upper bits and wrap.
There is a valid_mmap_phys_addr_range() arch hook where we could check for
>= 4G addresses and deny the mapping, but this hook takes an unsigned long
address:
static inline int valid_mmap_phys_addr_range(unsigned long addr, size_t size);
And drivers/char/mem.c:mmap_mem() calls it like this:
static int mmap_mem(struct file * file, struct vm_area_struct * vma)
{
size_t size = vma->vm_end - vma->vm_start;
if (!valid_mmap_phys_addr_range(vma->vm_pgoff << PAGE_SHIFT, size))
So that's not much help either.
This patch makes the hook take a pfn instead of a phys address.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
screen_info.h doesn't have anything to do with the tty layer and shouldn't be
included by tty.h. This patches removes the include and modifies all users to
directly include screen_info.h. struct screen_info is mainly used to
communicate with the console drivers in drivers/video/console. Note that this
patch touches every arch and I have no way of testing it. If there is a
mistake the worst thing that will happen is a compile error.
[akpm@osdl.org: fix arm build]
[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I found a bug in memory hot-add code for ia64.
IA64's code has copies of pgdat's array on each node to reduce memory
access over crossing node. This array is used by NODE_DATA() macro. When
new node is hot-added, this pgdat's array should be updated and copied on
new node too.
However, I used for_each_online_node() in scatter_node_data() to copy
it. This meant its array is not copied on new node.
Because initialization of structures for new node was halfway,
so online_node_map couldn't be set at this time.
To copy arrays on new node, I changed it to check value of pgdat_list[]
which is source array of copies. I tested this patch with my Memory Hotadd
emulation on Tiger4. This patch is for 2.6.17-git20.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cleanup: remove task_t and convert all the uses to struct task_struct. I
introduced it for the scheduler anno and it was a mistake.
Conversion was mostly scripted, the result was reviewed and all
secondary whitespace and style impact (if any) was fixed up by hand.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow to tie upper bits of syscall bitmap in audit rules to kernel-defined
sets of syscalls. Infrastructure, a couple of classes (with 32bit counterparts
for biarch targets) and actual tie-in on i386, amd64 and ia64.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Per zone counter infrastructure
The counters that we currently have for the VM are split per processor. The
processor however has not much to do with the zone these pages belong to. We
cannot tell f.e. how many ZONE_DMA pages are dirty.
So we are blind to potentially inbalances in the usage of memory in various
zones. F.e. in a NUMA system we cannot tell how many pages are dirty on a
particular node. If we knew then we could put measures into the VM to balance
the use of memory between different zones and different nodes in a NUMA
system. For example it would be possible to limit the dirty pages per node so
that fast local memory is kept available even if a process is dirtying huge
amounts of pages.
Another example is zone reclaim. We do not know how many unmapped pages exist
per zone. So we just have to try to reclaim. If it is not working then we
pause and try again later. It would be better if we knew when it makes sense
to reclaim unmapped pages from a zone. This patchset allows the determination
of the number of unmapped pages per zone. We can remove the zone reclaim
interval with the counters introduced here.
Futhermore the ability to have various usage statistics available will allow
the development of new NUMA balancing algorithms that may be able to improve
the decision making in the scheduler of when to move a process to another node
and hopefully will also enable automatic page migration through a user space
program that can analyse the memory load distribution and then rebalance
memory use in order to increase performance.
The counter framework here implements differential counters for each processor
in struct zone. The differential counters are consolidated when a threshold
is exceeded (like done in the current implementation for nr_pageache), when
slab reaping occurs or when a consolidation function is called.
Consolidation uses atomic operations and accumulates counters per zone in the
zone structure and also globally in the vm_stat array. VM functions can
access the counts by simply indexing a global or zone specific array.
The arrangement of counters in an array also simplifies processing when output
has to be generated for /proc/*.
Counters can be updated by calling inc/dec_zone_page_state or
_inc/dec_zone_page_state analogous to *_page_state. The second group of
functions can be called if it is known that interrupts are disabled.
Special optimized increment and decrement functions are provided. These can
avoid certain checks and use increment or decrement instructions that an
architecture may provide.
We also add a new CONFIG_DMA_IS_NORMAL that signifies that an architecture can
do DMA to all memory and therefore ZONE_NORMAL will not be populated. This is
only currently set for IA64 SGI SN2 and currently only affects
node_page_state(). In the best case node_page_state can be reduced to
retrieving a single counter for the one zone on the node.
[akpm@osdl.org: cleanups]
[akpm@osdl.org: export vm_stat[] for filesystems]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
Add ->retrigger() irq op to consolidate hw_irq_resend() implementations.
(Most architectures had it defined to NOP anyway.)
NOTE: ia64 needs testing. i386 and x86_64 tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup: remove irq_descp() - explicit use of irq_desc[] is shorter and more
readable.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the irq_affinity[NR_IRQS] array and move it into the
irq_desc[NR_IRQS].affinity field.
[akpm@osdl.org: sparc64 build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Memory hotplug code of i386 adds memory to only highmem. So, if
CONFIG_HIGHMEM is not set, CONFIG_MEMORY_HOTPLUG shouldn't be set.
Otherwise, it causes compile error.
In addition, many architecture can't use memory hotplug feature yet. So, I
introduce CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch fixes two spots in the SN kernel
that check a fixed prom revision number to determine prom
feature support. These checks are only valid on shub1 systems.
They are invalid on shub2 systems which have a different prom
with different revision numbers.
Signed-off-by: Aaron Young <ayoung@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Montecito is coming with dual core and threading, so this
four socket box can now have sixteen logical cpus.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pass the OS logical cpu number to the PROM. This allows PROM
to log the OS logical cpu number in error records viewed thru POD.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Chandra Seetharaman missed one place in commit:
65edc68c34
[but it only shows up when building the ski simulator configuration
of ia64, so thats understandable]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make use the of newly defined hotplug version of cpu_notifier functionality
wherever appropriate.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Goto-san's patch, we can add new pgdat/node at runtime. I'm now
considering node-hot-add with cpu + memory on ACPI.
I found acpi container, which describes node, could evaluate cpu before
memory. This means cpu-hot-add occurs before memory hot add.
In most part, cpu-hot-add doesn't depend on node hot add. But register_cpu(),
which creates symbolic link from node to cpu, requires that node should be
onlined before register_cpu(). When a node is onlined, its pgdat should be
there.
This patch-set holds off creating symbolic link from node to cpu
until node is onlined.
This removes node arguments from register_cpu().
Now, register_cpu() requires 'struct node' as its argument. But the array of
struct node is now unified in driver/base/node.c now (By Goto's node hotplug
patch). We can get struct node in generic way. So, this argument is not
necessary now.
This patch also guarantees add cpu under node only when node is onlined. It
is necessary for node-hot-add vs. cpu-hot-add patch following this.
Moreover, register_cpu calculates cpu->node_id by cpu_to_node() without regard
to its 'struct node *root' argument. This patch removes it.
Also modify callers of register_cpu()/unregister_cpu, whose args are changed
by register-cpu-remove-node-struct patch.
[Brice.Goglin@ens-lyon.org: fix it]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch to allocate pgdat and per node data area for ia64. The size
for them can be calculated by compute_pernodesize().
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is to refresh node_data[] array for ia64. As I mentioned previous
patches, ia64 has copies of information of pgdat address array on each node as
per node data.
At v2 of node_add, this function used stop_machine_run() to update them. (I
wished that they were copied safety as much as possible.) But, in this patch,
this arrays are just copied simply, and set node_online_map bit after
completion of pgdat initialization.
So, kernel must touch NODE_DATA() macro after checking node_online_map().
(Current code has already done it.) This is more simple way for just
hot-add.....
Note : It will be problem when hot-remove will occur,
because, even if online_map bit is set, kernel may
touch NODE_DATA() due to race condition. :-(
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a preparatory patch to make common code for updating of NODE_DATA() of
ia64 between boottime and hotplug.
Current code remembers pgdat address in mem_data which is used at just boot
time. But its information can be used at hotplug time by moving to global
value. The next patch uses this array.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When new node becomes enable by hot-add, new sysfs file must be created for
new node. So, if new node is enabled by add_memory(), register_one_node() is
called to create it. In addition, I386's arch_register_node() and a part of
register_nodes() of powerpc are consolidated to register_one_node() as a
generic_code().
This is tested by Tiger4(IPF) with node hot-plug emulation.
Signed-off-by: Keiichiro Tokunaga <tokuanga.keiich@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Refresh NODE_DATA() for generic archs. In this case, NODE_DATA(nid) ==
node_data[nid]. node_data[] is array of address of pgdat. So, refresh is
quite simple.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name of old add_memory() to arch_add_memory. And use node id to
get pgdat for the node at NODE_DATA().
Note: Powerpc's old add_memory() is defined as __devinit. However,
add_memory() is usually called only after bootup.
I suppose it may be redundant. But, I'm not well known about powerpc.
So, I keep it. (But, __meminit is better at least.)
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During some profiling I noticed that default_idle causes a lot of
memory traffic. I think that is caused by the atomic operations
to clear/set the polling flag in thread_info. There is actually
no reason to make this atomic - only the idle thread does it
to itself, other CPUs only read it. So I moved it into ti->status.
Converted i386/x86-64/ia64 for now because that was the easiest
way to fix ACPI which also manipulates these flags in its idle
function.
Cc: Nick Piggin <npiggin@novell.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Overloading of page fault notification with the notify_die() has performance
issues(since the only interested components for page fault is kprobes and/or
kdb) and hence this patch introduces the new notifier call chain exclusively
for page fault notifications their by avoiding notifying unnecessary
components in the do_page_fault() code path.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove VM_LOCKED before remap_pfn range from device drivers and get rid of
VM_SHM.
remap_pfn_range() already sets VM_IO. There is no need to set VM_SHM since
it does nothing. VM_LOCKED is of no use since the remap_pfn_range does not
place pages on the LRU. The pages are therefore never subject to swap
anyways. Remove all the vm_flags settings before calling remap_pfn_range.
After removing all the vm_flag settings no use of VM_SHM is left. Drop it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert a few stragglers over to for_each_possible_cpu(), remove
for_each_cpu().
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (65 commits)
ACPI: suppress power button event on S3 resume
ACPI: resolve merge conflict between sem2mutex and processor_perflib.c
ACPI: use for_each_possible_cpu() instead of for_each_cpu()
ACPI: delete newly added debugging macros in processor_perflib.c
ACPI: UP build fix for bugzilla-5737
Enable P-state software coordination via _PDC
P-state software coordination for speedstep-centrino
P-state software coordination for acpi-cpufreq
P-state software coordination for ACPI core
ACPI: create acpi_thermal_resume()
ACPI: create acpi_fan_suspend()/acpi_fan_resume()
ACPI: pass pm_message_t from acpi_device_suspend() to root_suspend()
ACPI: create acpi_device_suspend()/acpi_device_resume()
ACPI: replace spin_lock_irq with mutex for ec poll mode
ACPI: Allow a WAN module enable/disable on a Thinkpad X60.
sem2mutex: acpi, acpi_link_lock
ACPI: delete unused acpi_bus_drivers_lock
sem2mutex: drivers/acpi/processor_perflib.c
ACPI add ia64 exports to build acpi_memhotplug as a module
ACPI: asus_acpi_init(): propagate correct return value
...
Manual resolve of conflicts in:
arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c
include/acpi/processor.h
Default values for boolean and tristate options can only be 'y', 'm' or 'n'.
This patch removes wrong default for SCHED_SMT.
Signed-off-by: Jean-Luc Leger <jean-luc.leger@dspnet.fr.eu.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass the POSIX lock owner ID to the flush operation.
This is useful for filesystems which don't want to store any locking state
in inode->i_flock but want to handle locking/unlocking POSIX locks
internally. FUSE is one such filesystem but I think it possible that some
network filesystems would need this also.
Also add a flag to indicate that a POSIX locking request was generated by
close(), so filesystems using the above feature won't send an extra locking
request in this case.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
move_pages() is used to move individual pages of a process. The function can
be used to determine the location of pages and to move them onto the desired
node. move_pages() returns status information for each page.
long move_pages(pid, number_of_pages_to_move,
addresses_of_pages[],
nodes[] or NULL,
status[],
flags);
The addresses of pages is an array of void * pointing to the
pages to be moved.
The nodes array contains the node numbers that the pages should be moved
to. If a NULL is passed instead of an array then no pages are moved but
the status array is updated. The status request may be used to determine
the page state before issuing another move_pages() to move pages.
The status array will contain the state of all individual page migration
attempts when the function terminates. The status array is only valid if
move_pages() completed successfullly.
Possible page states in status[]:
0..MAX_NUMNODES The page is now on the indicated node.
-ENOENT Page is not present
-EACCES Page is mapped by multiple processes and can only
be moved if MPOL_MF_MOVE_ALL is specified.
-EPERM The page has been mlocked by a process/driver and
cannot be moved.
-EBUSY Page is busy and cannot be moved. Try again later.
-EFAULT Invalid address (no VMA or zero page).
-ENOMEM Unable to allocate memory on target node.
-EIO Unable to write back page. The page must be written
back in order to move it since the page is dirty and the
filesystem does not provide a migration function that
would allow the moving of dirty pages.
-EINVAL A dirty page cannot be moved. The filesystem does not provide
a migration function and has no ability to write back pages.
The flags parameter indicates what types of pages to move:
MPOL_MF_MOVE Move pages that are only mapped by the process.
MPOL_MF_MOVE_ALL Also move pages that are mapped by multiple processes.
Requires sufficient capabilities.
Possible return codes from move_pages()
-ENOENT No pages found that would require moving. All pages
are either already on the target node, not present, had an
invalid address or could not be moved because they were
mapped by multiple processes.
-EINVAL Flags other than MPOL_MF_MOVE(_ALL) specified or an attempt
to migrate pages in a kernel thread.
-EPERM MPOL_MF_MOVE_ALL specified without sufficient priviledges.
or an attempt to move a process belonging to another user.
-EACCES One of the target nodes is not allowed by the current cpuset.
-ENODEV One of the target nodes is not online.
-ESRCH Process does not exist.
-E2BIG Too many pages to move.
-ENOMEM Not enough memory to allocate control array.
-EFAULT Parameters could not be accessed.
A test program for move_pages() may be found with the patches
on ftp.kernel.org:/pub/linux/kernel/people/christoph/pmig/patches-2.6.17-rc4-mm3
From: Christoph Lameter <clameter@sgi.com>
Detailed results for sys_move_pages()
Pass a pointer to an integer to get_new_page() that may be used to
indicate where the completion status of a migration operation should be
placed. This allows sys_move_pags() to report back exactly what happened to
each page.
Wish there would be a better way to do this. Looks a bit hacky.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the gen_pool allocator (lib/genalloc.c) to utilize a bitmap scheme
instead of the buddy scheme. The purpose of this change is to eliminate
the touching of the actual memory being allocated.
Since the change modifies the interface, a change to the uncached allocator
(arch/ia64/kernel/uncached.c) is also required.
Both Andrey Volkov and Jes Sorenson have expressed a desire that the
gen_pool allocator not write to the memory being managed. See the
following:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113518602713125&w=2http://marc.theaimsgroup.com/?l=linux-kernel&m=113533568827916&w=2
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: Andrey Volkov <avolkov@varma-el.com>
Acked-by: Jes Sorensen <jes@trained-monkey.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidate the various arch-specific implementations of pxm_to_node() and
node_to_pxm() into a single generic version.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the get_sb() filesystem operation to take an extra argument that
permits the VFS to pass in the target vfsmount that defines the mountpoint.
The filesystem is then required to manually set the superblock and root dentry
pointers. For most filesystems, this should be done with simple_set_mnt()
which will set the superblock pointer and then set the root dentry to the
superblock's s_root (as per the old default behaviour).
The get_sb() op now returns an integer as there's now no need to return the
superblock pointer.
This patch permits a superblock to be implicitly shared amongst several mount
points, such as can be done with NFS to avoid potential inode aliasing. In
such a case, simple_set_mnt() would not be called, and instead the mnt_root
and mnt_sb would be set directly.
The patch also makes the following changes:
(*) the get_sb_*() convenience functions in the core kernel now take a vfsmount
pointer argument and return an integer, so most filesystems have to change
very little.
(*) If one of the convenience function is not used, then get_sb() should
normally call simple_set_mnt() to instantiate the vfsmount. This will
always return 0, and so can be tail-called from get_sb().
(*) generic_shutdown_super() now calls shrink_dcache_sb() to clean up the
dcache upon superblock destruction rather than shrink_dcache_anon().
This is required because the superblock may now have multiple trees that
aren't actually bound to s_root, but that still need to be cleaned up. The
currently called functions assume that the whole tree is rooted at s_root,
and that anonymous dentries are not the roots of trees which results in
dentries being left unculled.
However, with the way NFS superblock sharing are currently set to be
implemented, these assumptions are violated: the root of the filesystem is
simply a dummy dentry and inode (the real inode for '/' may well be
inaccessible), and all the vfsmounts are rooted on anonymous[*] dentries
with child trees.
[*] Anonymous until discovered from another tree.
(*) The documentation has been adjusted, including the additional bit of
changing ext2_* into foo_* in the documentation.
[akpm@osdl.org: convert ipath_fs, do other stuff]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sorry I didn't notice earlier, but that BUG_ON triggers for me on the
simulator. AFAICS the mask for itv is set in cpu_init(), which comes
after sal_init(). Consequently on the simulator the itv still has its
start value of zero. I've probably missed something, but I wonder why
at this stage of the boot you even need to save and restore the itv?
Signed-Off-By: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following patch fixes a bug in the SGI Altix tioce_bus_fixup()
code. ce_dre_comp_err_addr needs to be zero'd out not ~0ULL. As
a result completion errors weren't being captured.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
struct ia64_sal_os_state has three semi-independent sections. The code
in mca_asm.S assumes that these three sections are contiguous, which
makes it very awkward to add new data to this structure. Remove the
assumption that the sections are contiguous. Define a macro to shorten
references to offsets in ia64_sal_os_state.
This patch does not change the way that the code behaves. It just
makes it easier to update the code in future and to add fields to
ia64_sal_os_state when debugging the MCA/INIT handlers.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When I tried to use PCI Express Hotplug driver on my ia64 box, I
noticed that "PCI Express support" is not even selectable on ia64.
This patch makes PCI Express support selectable.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There is an SN bug in sn_hwperf.c that affects systems with 1024n or 1024p.
The bug manifests itself 2 ways: IO interrupts are not always
targeted to the nearest node, and 2) the "cat /proc/sgi_sn/sn_topology"
commands fails with "cannot allocate memory".
The code is using the wrong macros for validating node numbers.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
One more trivial, stand-alone patch from the Xen/ia64 review. Sanity
check usage of the reserved region numbers.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is a trivial stand-alone patch out of the Xen/ia64 patches. Add
a vmlinuz build target to be more compatible with x86-ish targets.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
MSI callouts for altix. Involves a fair amount of code reorg in sn irq.c
code as well as adding some extensions to the altix PCI provider abstaction.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract IA64_FIRST_DEVICE_VECTOR/IA64_LAST_DEVICE_VECTOR since SN platforms
use a subset of the IA64 range. Implement this by making the above macros
global variables which the platform can override in it setup code.
Also add a reserve_irq_vector() routine used by SN to mark a vector's as
in-use when that weren't allocated through assign_irq_vector().
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for making ESI calls [1]. ESI stands for "Extensible SAL
specification" and is basically a way for invoking firmware
subroutines which are identified by a GUID. I don't know whether ESI
is used by vendors other than HP (if you do, please let me know) but
as firmware "backdoors" go, this seems one of the cleaner methods, so
it seems reasonable to support it, even though I'm not aware of any
publicly documented ESI calls. I'd have liked to make the ESI module
completely stand-alone, but unfortunately that is not easily (or not
at all) possible because in order to make ESI calls in physical mode,
a small stub similar to the EFI stub is needed in the kernel proper.
I did try to create a stub that would work in user-level, but it
quickly got ugly beyond recognition (e.g., the stub had to make
assumptions about how the module-loader generated call-stubs work) and
I didn't even get it to work (that's probably fixable, but I didn't
bother because I concluded it was too ugly anyhow). While it's not
terribly elegant to have kernel code which isn't actively used in the
kernel proper, I think it might be worth making an exception here for
two reasons: the code is trivially small (all that's really needed is
esi_stub.S) and by including it in the normal kernel distro, it might
encourage other OEMs to also use ESI, which I think would be far
better than each inventing their own firmware "backdoor".
The code was originally written by Alex. I just massaged and packaged
it a bit (and perhaps messed up some things along the way...).
Changes since first version of patch that was posted to mailing list:
* Export ia64_esi_call and ia64_esi_call_phys() as GPL symbols.
* Disallow building esi.c as a module for now. Building as a module
would currently lead to an unresolved reference to "sal_lock" on SMP kernels
because that symbol doesn't get exported.
* Export esi_call_phys() only if ESI is enabled.
* Remove internal stuff from esi.h and add a "proc_type" argument to
ia64_esi_call() such that serialization-requirements can be expressed (ESI
follows SAL here, where procedure calls may have to be serialized, are
MP-safe, or MP-safe andr reentrant).
[1] h21007.www2.hp.com/dspp/tech/tech_TechDocumentDetailPage_IDX/1,1701,919,00.html
Signed-off-by: David Mosberger <David.Mosberger@acm.org>
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Linux ia64 port tried to decode the processor family number
to something human-readable, but Intel brandnames don't change
synchronously with updates to the family number. Adopt a more
i386-like approach and just print the family number in decimal.
Add a new field "model name" that uses PAL_BRAND_INFO to find
the official name for the cpu, or on older systems, falls back
to using the well-known codenames (Merced, McKinley, Madison).
Signed-off-by: Tony Luck <tony.luck@intel.com>
Calls to set_irq_info in set_irq_affinity_info() is redundant because
irq_affinity mask was set just one line immediately above it. Remove
that duplicate call.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When CONFIG_PCI_MSI is set, move_irq() is an empty function, causing
grief when sys admin tries to bind interrupt to CPU.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
When building sim_defconfig, which does not define CONFIG_ACPI
arch/ia64/kernel/acpi.c:71: warning: 'acpi_madt_rev' defined but not used
really acpi.c should not be built when CONFIG_ACPI=n...
Signed-off-by: Len Brown <len.brown@intel.com>
This closes a couple holes in our attribute aliasing avoidance scheme:
- The current kernel fails mmaps of some /dev/mem MMIO regions because
they don't appear in the EFI memory map. This keeps X from working
on the Intel Tiger box.
- The current kernel allows UC mmap of the 0-1MB region of
/sys/.../legacy_mem even when the chipset doesn't support UC
access. This causes an MCA when starting X on HP rx7620 and rx8620
boxes in the default configuration.
There's more detail in the Documentation/ia64/aliasing.txt file this
adds, but the general idea is that if a region might be covered by
a granule-sized kernel identity mapping, any access via /dev/mem or
mmap must use the same attribute as the identity mapping.
Otherwise, we fall back to using an attribute that is supported
according to the EFI memory map, or to using UC if the EFI memory
map doesn't mention the region.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Bob Picco noted that 6edfba1b33
dropped the -ffreestanding compiler flag from the top level
Makefile, which allows the compiler to substitute memcpy() in
places where strcpy() is used with a known size source string.
But the ia64 memcpy() returns 0 for success, and "bytes copied"
for failure.
Fix to return the address of the destination string (like
stdlibc version, and other architectures). There are no
places where ia64 specific code makes use of the non-standard
return value.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] update sn2 defconfig
[IA64] Add mca recovery failure messages
[IA64-SGI] fix SGI Altix tioce_reserve_m32() bug
[IA64] enable dumps to capture second page of kernel stack
[IA64-SGI] - Reduce overhead of reading sn_topology
[IA64-SGI] - Fix discover of nearest cpu node to IO node
[IA64] IOC4 config option ordering
[IA64] Setup an IA64 specific reclaim distance
[IA64] eliminate compile time warnings
[IA64] eliminate compile time warnings
[IA64-SGI] SN SAL call to inject memory errors
[IA64] - Fix MAX_PXM_DOMAINS for systems with > 256 nodes
[IA64] Remove unused variable in sn_sal.h
[IA64] Remove redundant NULL checks before kfree
[IA64] wire up compat_sys_adjtimex()
Update SN2 defconfig to latest kernel and add QLA FC drivers commonly
found in SN2 boxes.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When the mca recovery code encounters a condition that makes
the MCA non-recoverable, print the reason it could not recover.
This will make it easier to identify why the recovery code did
not recover.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following patch fixes a bug in the SGI Altix tioce_reserve_m32()
code. The bug was that we could walking past the end of the CE ASIC
32/40bit PMU ATE Buffer, resulting in a PIO Reply Error.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
MPI programs using certain debug options have a long
startup time. This was traced to a "vmalloc/vfree" in
the code that reads /proc/sgi_sn/sn_topology. On large
systems, vfree requires an IPI to all cpus to do TLB
purging.
Replace the vmalloc/vfree with kmalloc/kfree. Although
the size of the structure being allocated is unknown, it
will not not exceed 96 bytes.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix a bug that causes discovery of the nearest node/cpu to
a TIO (IO node) to fail.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call. It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).
This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_splice() moves data to/from pipes with a file input/output. sys_vmsplice()
moves data to a pipe, with the input being a user address range instead.
This uses an approach suggested by Linus, where we can hold partial ranges
inside the pages[] map. Hopefully this will be useful for network
receive support as well.
Signed-off-by: Jens Axboe <axboe@suse.de>
SERIAL_SGI_IOC4 and BLK_DEV_SGIIOC4 depend upon SGI_IOC4, and
SERIAL_SGI_IOC3 depends upon SGI_IOC3. Currently the definitions
are out of order in the config sequence.
Fix by including drivers/sn/Kconfig immediately after SGI_SN,
upon which SGI_IOC4 and SGI_IOC3 depend.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes following compile time warnings:
drivers/pci/pci-sysfs.c: In function `pci_read_legacy_io':
drivers/pci/pci-sysfs.c:257: warning: implicit declaration of function `ia64_pci_legacy_read'
drivers/pci/pci-sysfs.c: In function `pci_write_legacy_io':
drivers/pci/pci-sysfs.c:280: warning: implicit declaration of function `ia64_pci_legacy_write'
It also fixes wrong definition of ia64_pci_legacy_write (type of `bus' is not
`pci_dev', but `pci_bus').
Signed-Off-By: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is a trivial patch to remove following compile time warning:
arch/ia64/ia32/../../../fs/binfmt_elf.c:508: warning: 'randomize_stack_top' defined but not used
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
