Teach the MMC/SD/SDIO core about using SPI mode.
- Use mmc_host_is_spi() so enumeration works through SPI signaling
and protocols, not just the native versions.
- Provide the SPI response type flags with each request issued,
including requests from the new lock/unlock code.
- Understand that cmd->resp[0] and mmc_get_status() results for SPI
return different values than for "native" MMC/SD protocol; this
affects resetting, checking card lock status, and some others.
- Understand that some commands act a bit differently ... notably:
* OP_COND command doesn't return the OCR
* APP_CMD status doesn't have an R1_APP_CMD analogue
Those changes required some new and updated primitives:
- Provide utilities to access two SPI-only requests, and one
request that wasn't previously needed:
* mmc_spi_read_ocr() ... SPI only
* mmc_spi_set_crc() ... SPI only (override by module parm)
* mmc_send_cid() ... for use without broadcast mode
- Updated internal routines:
* Previous mmc_send_csd() modified into mmc_send_cxd_native();
it uses native "R2" responses, which include 16 bytes of data.
* Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
helper for command-and-data access
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
- Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper
- Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
those helper routines based on whether they're native or SPI
The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Teaching the MMC/SD block card driver about SPI.
- Provide the SPI response type flags with each request issued.
- Understand that multiblock SPI writes don't use STOP_TRANSMISSION.
- Correct check for APP_CMD failure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Increase delay for power up in order to support some slower boards.
Also add some comments about why the delays are there.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In a few places, sdio_uart_irq() is called directly instead of waiting
for the actual interrupt to be raised and the SDIO IRQ thread scheduled
in order to reduce latency. However, some interaction with the tty core
may end up calling us back (serial echo, flow control, etc.) creating
two issues:
- the host lock gets claimed twice from the same thread causing a
deadlock;
- the same direct calls to sdio_uart_irq() may be performed causing
unexpected reentrancy into the IRQ handler.
This patch handles both of those issues.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Note that the default baudrate is 4800 instead of 9600 as a convenience
because that's what GPS devices want which is still the main use for
this driver.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add sdio_f0_readb() and sdio_f0_writeb() functions to reading and
writing function 0 registers. Writes outside the vendor specific CCCR
registers (0xF0 - 0xFF) are not permitted.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Replace all cases of BUG_ON with WARN_ON where there is a chance
(with varying degrees of slim) that the kernel can continue without
incidence.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Extend sdio_readsb(), sdio_writesb(), sdio_memcpy_fromio(), and
sdio_memcpy_toio() to handle any length of buffer by splitting the transfer
into several IO_RW_EXTENDED commands. Typically, a transfer would be split
into a single block mode transfer followed by a byte mode transfer for the
remainder but we also handle lack of block mode support and the block size
being greater than 512 (the maximum byte mode transfer size).
host->max_seg_size <= host->max_req_size so there's no need to check both
when determining the maximum data size for a single command.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Before a driver is probed, set the function's block size to the default so the
driver is sure the block size is something sensible and it needn't explicitly
set it.
The default block size is the largest that's supported by both the card and
the host, with a maximum of 512 to ensure aribitrarily sized transfer use the
optimal (least) number of commands.
See http://lkml.org/lkml/2007/8/7/150 for reasons for the block size choice.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
On Wed, Jul 25, 2007 at 04:03:04AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.22-rc6-mm1:
>...
> git-mmc.patch
>...
> git trees
>...
sdio_dev_attrs[] can become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support the multi-byte transfer operation, including handlers for
common operations like writel()/readl().
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This mimics what the serial_core does. Useful for diagnostics.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This currently only accepts the GPS class since that's all I have for
testing. Tested with a Matsushita GPS and gpsd version 2.34.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is sometimes necessary to give up on trying to claim the host lock,
especially if that happens in a thread that has to be stopped.
While at it, fix the description for mmc_claim_host() which was wrong.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The problem is that the sdio_bus must be registered before any SDIO
drivers are registered against it otherwise the kernel sulks. Because
the sdio_bus registration happens through module_init (equivalent to
device_initcall), then any SDIO
drivers linked before the SDIO core code in the kernel will be initialized
first.
Upcoming SDIO function drivers are likely to be located outside the
drivers/mmc directory as it is common practice to group drivers according
to their function rather than the bus they use. SDIO drivers are therefore
likely to appear at random location in the kernel link.
To make sure the sdio_bus is always initialized before any SDIO drivers,
let's move the MMC init to the subsys_initcall level.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add a more clean separation between global, common CIS information
and the function specific one as we need the common information in
places where no specific function is specified.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This way those tuples that the core cares about are consumed by the core
code, and tuples that only function drivers might make sense of are
available to drivers.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Like many other buses, the devices (functions) on the SDIO bus
must be enabled before they can be used. Add functions that allow
drivers to do so.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This kind of transfer is not supported, so don't advertise it and make it
fail early.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The MMC_DATA_MULTI flag never had a proper definition of what it
means, so remove it and let the drivers check the block count in
the request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The write parameter in mmc_set_data_timeout() is redundant as the
data structure contains information about the direction of the
transfer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes a bug in AT91 mmc host driver, that enables the wakeup
from suspend on card detection pin even if the card detect pin is not
available (==0). If not card detection pin is defined, IRQ0 == FIQ gets
enabled and if some activity is present on that pin, the system gets a
FIQ request, that causes a crash.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is fully legal for a controller to start issuing data related
interrupts before it has signalled that the command has completed.
Make sure the driver actually can handle this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some SDHC cards report an invalid maximum block size, in these cases
assume they support block sizes up to 512 bytes instead of returning
an error.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The block count register shouldn't be trusted for single block transfers,
so avoid using it completely when calculating transferred bytes.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cleanup with whitespace/tab at the end of lines.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Reorganize the code that initializes mmc_block's bounce buffer in
order to avoid warnings when MMC_BLOCK_BOUNCE isn't used.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes the following section mismatch warnings
...
WARNING: vmlinux.o(.init.text+0x29d40): Section mismatch: reference to .exit.text:wbsd_release_resources (between 'wbsd_init' and 'wbsd_probe')
WARNING: vmlinux.o(.init.text+0x29d49): Section mismatch: reference to .exit.text:wbsd_free_mmc (between 'wbsd_init' and 'wbsd_probe')
WARNING: vmlinux.o(.init.text+0x29f28): Section mismatch: reference to .exit.text:wbsd_free_mmc (between 'wbsd_init' and 'wbsd_probe')
...
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
drivers/mmc/core/: make 3 functions static
mmc: add missing printk levels
mmc: remove redundant debug information from sdhci and wbsd
mmc: proper debugging output in core
mmc: be more verbose about card insertions/removal
mmc: Don't hold lock when releasing an added card
mmc: add a might_sleep() to mmc_claim_host()
mmc: update kerneldoc
mmc: update header file paths
sdhci: add support to ENE-CB714
mmc: check error bits before command completion
This patch makes the following needlessly global functions static:
- sd_ops.c: mmc_app_cmd()
- core.c: __mmc_release_bus()
- core.c: mmc_start_request()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure that the debugging output in the core is complete.
This should allow us to clean up all the extra debug output
that each and every other host driver seems to contain.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Let the user know that the kernel actually detected the card
by printing some basic information in dmesg.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When the card has been added to the device model, it might be bound
to a card driver. Therefore, we have to release the host lock when
trying to remove it as we otherwise might deadlock with the driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In the normal case, the host lock can be claimed directly.
When it cannot, the caller will sleep. Make sure we don't
have any latent bugs by always calling might_sleep().
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Added its pci_id and implemented a quirk for it because this
controller needs to reset cmd and data when setting ios.
Signed-off-by: Leandro Dorileo <dorileo@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers signal "command complete" even on failures (which
they are allowed to do according to the spec). Make sure we check
the error bits first so we don't get any false positives.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The controller has a bit indicating that one of the higher bits (the
error bits) are set. A previous bug caused this bit to be masked, but
since that bug has been fixed we have to clear it explicictly.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This piece of code enable the system to be wake-up by a card insertion or removal.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (50 commits)
[ARM] sa1100: remove boot time RTC initialisation
[ARM] sa1100: stop doing our own rtc management over suspend
[ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
[ARM] 4473/2: Take the HWCAP definitions out of the elf.h file
[ARM] pxa: move platform devices to separate header file
[ARM] pxa: move device registration into CPU-specific file
[ARM] pxa: remove boot time RTC initialisation
[ARM] pxa: stop doing our own rtc management over suspend
[ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
[ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
[ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
[ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
[ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
[ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
[ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS
[ARM] 4434/1: PXA: remove PXA_IRQ_SKIP
[ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
[ARM] pxa: move pm_ops structure into CPU specific files
[ARM] pxa: introduce cpu_is_pxaXXX macros
[ARM] pxa: remove MMC register defines from pxa-regs.h
...
pxamci.h redefines the MMC registers differently so they can be used
with ioremap. Remove the incompatible definitions from pxa-regs.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes hanging using multi block operations (seen during CMD25).
Follows closely the datasheet flowcharts.
This piece of code handles better big file writing. I had to take care
of the notbusy signal during write (at91_mci_handle_cmdrdy function) and
to rearrange the AT91_MCI_ENDRX and AT91_MCI_RXBUFF flag usage.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Typo fix in at91_mci driver : standardized the typo
(at91_mci everywhere)
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Whenever a power interrupt is signaled it is also reported as an unexpected
one. All other unexpected interrupts get lost. Cause is a not inversed
bitmask to remove power interrupts from the status.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move bus operations to its own file for the sake of clarity. Also
delegate sysfs attributes to bus handlers in preparation for other
more exotic types.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
ENE has a very weird design where an SDHCI device (0805) is presented
on the PCI bus, but that device is non-functional, and the real device
is hidden as a more generic device.
Signed-off-by: Milko Krachounov <milko@3mhz.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some hosts cannot do scatter/gather in hardware. Since not doing sg
is such a big performance hit, we (optionally) bounce the requests
to a simple linear buffer that we hand over to the driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ignoring OMAP_MMC_STAT_CARD_ERR, treating it as if the command
completed correctly.
Signed-off-by: Ragner Magalhaes <ragner.magalhaes@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure we don't call the switch function on cards too old to
support it. They should just ignore it, but some have been reported
to lock up instead.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix a broken if clause which was causing SD cards to go into
4-bit mode even if the host did not support it.
(Reported by David Brownell and Marc Pignat)
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix compilation error by removing command decoding from at91_mci.c driver.
Decoding commands in the host driver is the wrong way.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
... and make it depend on the response flag instead of the command type.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When the device hits certain memory boundaries, it signals an
interrupt and expects to be serviced. We don't need the feature
but we need to make sure the device doesn't stall.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch has changed command types check from data flags.
MMC_STOP_TRANSMISSION is never passed to au1xmmc_send_command().
SEND_STOP() is used for MMC_STOP_TRANSMISSION.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As mmc_detect_change() can be called from irq context, using
claim (which can sleep) is inherently unsafe. Use the host
spinlock instead, which also is faster.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Socket power must be fully controlled by adapter driver. This also prevents
unnecessary power-off of the socket when media driver is unloaded, yet
media remains in the socket.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move divisor calculation into a separate function and re-arrange the
init order to make MMC_POWER_ON work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As discussed earlier on LKML:
http://lkml.org/lkml/2006/5/4/44
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch add a missing '\n' at the end of the 'cover is open' string
in mmc_omap_switch_handler().
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch makes the needlessly global tifm_sd_set_dma_data() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since many have the system root on MMC/SD we must allow some foot
shooting when it comes to resume.
We cannot detect if a card is removed and reinserted during suspend,
so the safe approach would be to assume it was, avoiding potential
filesystem corruption. This will of course not work if you cannot
release the card before suspend.
This commit adds a compile time option that makes the MMC layer
assume the card wasn't touched if it is redetected upon resume.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix handling of low voltage MMC cards.
The latest MMC and SD specs both agree that support for
low-voltage operations is indicated by bit 7 in the OCR.
The MMC spec states that the low voltage range is
1.65-1.95V while the SD spec leaves the actual voltage
range undefined - meaning that there is still no such
thing as a low voltage SD card.
However, an old Sandisk spec implied that bits 7.0
represented voltages below 2.0V in 1V or 0.5V increments,
and the code was accordingly written with that expectation.
This confusion meant that host drivers attempting to support
the typical low voltage (1.8V) would set the wrong bits in
the host OCR mask (usually bits 5 and/or 6) resulting in the
the low voltage mode never being used.
This change corrects the low voltage range and adds sanity
checks on the reserved bits (0-6) and for SD cards that
claim to support low-voltage operations.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Consolidate the list of available voltages.
Up until now, a separate set of defines has been
used for host->vdd than that used for the OCR
voltage mask values. Having two sets of defines
allows them to get out of sync and the current
sets are already inconsistent with one claiming
to describe ranges and the other specific voltages.
Only the SDHCI driver uses the host->vdd defines and
it is easily fixed to use the OCR defines.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Delegate protocol handling to "bus handlers". This allows the core to
just handle the task of arbitrating the bus. Initialisation and
pampering of cards is now done by the different bus handlers.
This design also allows MMC and SD (and later SDIO) to be more cleanly
separated, allowing easier maintenance.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move the check for supported data opcodes to the beginning of the
request function to avoid wedging the card.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The classic MMC bus was defined as multi card bus
system, which is reflected in the design in the MMC
layer.
When SD showed up, the bus topology was abandoned
and a star topology (one card per host) was mandated.
MMC version 4 has followed this, officially deprecating
the bus topology.
As we do not have any known users of the bus
topology we can remove support for it. This will
simplify the code and rectify some incorrect
assumptions in the newer additions.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Suspending MMC/SD cards (versus removing and readding them) is an
inherently unsafe operation and has even been broken for some time.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure we don't deadlock when removing a suspended block
queue, something that might happen if the card is removed during
suspend.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure we kill of any pending detection runs when the host
is removed instead of when it is freed. Also add some debugging
to make sure the driver doesn't queue up more detection after it
has removed the host.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The mmc block queue functions are tailored for the mmc_block
driver, so move those functions into that module.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The "present" state indicates that the card is a registered device, so
it is more clear to put it together with the actual registration.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
All host drivers were #include:ing mmc/protocol.h just to
get access to the OCR bit defines. Move these to host.h instead.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for MMC 4.2 sector based cards. This tweaks the init a
bit and reads a new field out of the EXT_CSD.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It was found that delays associated with issue and completion of the commands
severely limit performance of the new, fast SD cards. To alleviate this issue
scatter-gather emulation in software is implemented for both dma and pio
transfer modes. Non-block aligned and high memory sg entries are accounted
for.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Resume should not explicitly check for media type. Instead, it may relay
on success of socket initialization.
Small changes are introduced to tifm_sd_initialize to make it more robust.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
State machine used to to track mmc command state was found to be fragile
and unreliable, making many cards unusable. The safer solution is to perform
all needed checks at every card event.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
To allow for switching of trasfer mode (dma/pio) on a per-request basis,
pio and dma request issue and completion function are now merged.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
host->flags variable was hosting a collection of bits with different
semantics. For clarity, hardware bit masks are now defined as macros,
socket flags represented as bit fields and flags (now cmd_flags) only
hosts command processing modifiers.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This wait was needed because of the mmc layer failure to wait for completion
of all outstanding commands before host removal. It should be fixed now in
the mmc layer.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
tifm_sd_terminate can only lawfully be called on device removal so it can be
merged with tifm_sd_remove.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Remove code duplicating the kernel functionality and clean up data
structures involved in driver matching.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Instead of passing transformed value of adapter interrupt status to
socket drivers, implement two separate callbacks - one for card events
and another for dma events.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Block completion interrupts occur faster than we can process
them, so just ignore them competely.
Commit also fixes up some incorrect register defines.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Now that we've fixed our only offender when it comes to strange sg
list, add a check so that future users keep the sg list proper with
regard to transfer size.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
mmc layer may introduce additional (compared to block layer) limits on
request size. Culling of the sg list to match adjusted request size
simplifies the handling of such cases in the low level driver, allowing
it to skip block count checks while processing sg entries.
(fixes for wbsd and sdhci by Pierre Ossman)
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make use of add_uevent_var() instead of (often incorrectly) open coding it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Eric Rannaud <eric.rannaud@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SDHC controllers cannot process shorter transfers.
They has to be handled as longer ones, but it such case CRC
error is evaluated. There was a case in the code still,
where this error is not ignored as it should to be process
these transfers.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The interrupt is shared with another device, which resumes earlier than the
sdhci controller, and generates an interrupt.
The sdhci interrupt handler runs, sees 0xffffffff in its own device's
interrupt status, and tries to handle it.. The reason for the 0xffffffff
is that the device is still suspended, and *all* regs are reading back
0xffffffff.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The new high-speed timings are similar to each other and the old
system, but not identical. And although things "just work" most of
the time, sometimes it does not. So we need to start marking which
hosts are known to fully comply with the new timings.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
tifm_sd: treat "status error" as normal command completion
mmc: wbsd: Remove stray kunmap_atomic()
mmc: sdhci: Stop asking for mail
mmc: sdhci: Remove driver version
mmc: wbsd: Remove driver version
