Commit Graph

5770 Commits

Author SHA1 Message Date
Ulf Hansson
400fdb25c8 mmc: rtsx_usb: Enable MMC_CAP_ERASE to allow erase/discard/trim requests
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michał Pecio <michal.pecio@gmail.com>
2018-05-08 09:43:27 +02:00
Ulf Hansson
ec30f11e82 mmc: rtsx_usb: Use the provided busy timeout from the mmc core
Instead of using a fixed 3s timeout for commands with R1B responses,
convert to use the per request calculated busy timeout from the mmc core.

This is needed to cope with requests that requires longer timeout, for
example erase/discard commands.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michał Pecio <michal.pecio@gmail.com>
2018-05-08 09:43:26 +02:00
Ulf Hansson
4b7d45451d mmc: rtsx_usb: Use MMC_CAP2_NO_SDIO
Instead of having to return -EINVAL when requested to send SDIO specific
commands, let's set MMC_CAP2_NO_SDIO as it completely prevents them.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michał Pecio <michal.pecio@gmail.com>
2018-05-08 09:43:15 +02:00
Ulf Hansson
7405df4c79 mmc: core: Implement ->sw_reset bus ops for SDIO
Let's implement the ->sw_reset() bus ops to allow SDIO func drivers, in
particular, to make a SW reset without doing a full power cycle of the SDIO
card.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:56 +02:00
Ulf Hansson
508c9864cc mmc: core: Share internal function to set initial signal voltage
Move the corresponding code for setting the initial signal voltage, from
mmc_power_up() into a new function, mmc_set_initial_signal_voltage().

Make the function internally available to the mmc core, as to allow the
following changes to make use of it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:50 +02:00
Ulf Hansson
1433269c4d mmc: core: Export a function mmc_sw_reset() to allow soft reset of cards
It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.

However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.

To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.

The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:42 +02:00
Ulf Hansson
3a3db6030b mmc: core: Rename ->reset() bus ops to ->hw_reset()
The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:29 +02:00
Ulf Hansson
fb09f44e29 mmc: core: Re-factor some code for SDIO re-initialization
The mmc_sdio_init_card() function has a couple of callers. In the
re-initialization cases, some additional reset commands are issued before
mmc_sdio_init_card() is called. As these additional reset commands are the
same, let's move these into a new static function, mmc_sdio_reinit_card()
and call mmc_sdio_init_card() from there. In this way we avoid the open
coding.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:32:36 +02:00
Ulf Hansson
5581cfcdcc Merge branch 'sdhci_omap' into next
Merge immutable branch for sdhci-omap to add UHS/HS200 mode support.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 10:34:06 +02:00
Shawn Lin
bfd694d5e2 mmc: core: Add tunable delay before detecting card after card is inserted
Allow to use tunable delay before detecting card after card is inserted,
which either comes from firmware node, or comes from debounce value
passed on to mmc_gpiod_request_cd(). If the platform doesn't support
debounce, then we fall back to use the debounce period as the delay,
otherwise, it behaves the same as before that a HW debounce(if set) plus
a 200ms hardcode delay before detecting the card.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 10:33:52 +02:00
Kishon Vijay Abraham I
3f40287802 mmc: sdhci-omap: Get IODelay values for 3.3v DDR mode
commit 8d20b2eae6 ("mmc: sdhci_omap: Add support to set
IODELAY values") stored IODelay values for all MM/SD modes
in pinctrl_state structure member of sdhci_omap_host. However for
DDR mode it gets IODelay values only for 1.8v DDR mode. Since some of
the platforms which uses sdhci-omap has IO lines connected to 3.3v,
get IODelay values for 3.3v DDR mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:37:13 +02:00
Kishon Vijay Abraham I
efde12b246 mmc: sdhci-omap: Add sdhci_omap specific ops for enable_sdio_irq
Add sdhci_omap_enable_sdio_irq to set CTPL and CLKEXTFREE bits in
MMCHS_CON register required to detect asynchronous card interrupt
on DAT[1].

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:37:12 +02:00
Kishon Vijay Abraham I
6d75df75ab mmc: sdhci-omap: Add support for MMC/SD controller in k2g SoC
Add support for the new compatible added specifically to support
k2g's MMC/SD controller.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:37:12 +02:00
Kishon Vijay Abraham I
25f80d8605 mmc: sdhci-omap: Workaround for Errata i834
Errata i834 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions the maximum
obtainable timeout through MMC host controller is 700ms. And for
commands taking longer than 700ms, hardware timeout should be
disabled and software timeout should be used.

The workaround for Errata i834 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci-omap.

[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:37:11 +02:00
Kishon Vijay Abraham I
fc1fa1b7db mmc: sdhci: Program a relatively accurate SW timeout value
sdhci has a 10 second timeout to catch devices that stop responding.
In the case of quirk SDHCI_QUIRK2_DISABLE_HW_TIMEOUT, instead of
programming 10 second arbitrary value, calculate the total time it would
take for the entire transfer to happen and program the timeout value
accordingly.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:36:20 +02:00
Adrian Hunter
0bb28d738f mmc: sdhci: Factor out target_timeout calculation
Factor out the target_timeout calculation so it can be re-used.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:36:20 +02:00
Adrian Hunter
a999fd9392 mmc: sdhci: Add quirk to disable HW timeout
Add quirk to disable HW timeout if the requested timeout is more than the
maximum obtainable timeout.

Also, if the quirk is set and ->get_max_timeout_count() is not implemented,
max_busy_timeout is set to zero.

Based-on-patch-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:36:19 +02:00
Kishon Vijay Abraham I
c16bc9a767 mmc: sdhci: Disable 1.8v modes (HS200/HS400/UHS) if controller can't support 1.8v
The SDHCI controller in a SoC might support HS200/HS400 (indicated
using mmc-hs200-1_8v/mmc-hs400-1_8v dt property), but if the board is
modeled such that the IO lines are not connected to 1.8v then
HS200/HS400 cannot be supported. Disable HS200/HS400 if the board
does not have 1.8v connected to the IO lines. Also Disable DDR/UHS in 1.8v
if the IO lines are not connected to 1.8v.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:36:19 +02:00
Kishon Vijay Abraham I
1d3a2220c2 mmc: sdhci-omap: Invoke sdhci_get_of_property to read sdhci dt properties
Invoke sdhci_get_of_property defined in sdhci-pltfm.c to read
sdhci specific properties from dt node.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:36:18 +02:00
Kishon Vijay Abraham I
212f4f8a44 mmc: sdhci-omap: Workaround for Errata i843
Errata i843 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
PG 1.0/1.1 silicon has limitations w.r.t frequencies at which MMC1/2/3
can operate.

Use soc_device_match() to identify rev 1.0/1.1 silicon and
override mmc->f_max according to the errata workaround.
"max-frequency" dt property cannot be used since the device
tree is added for rev 2.0 silicon.

soc_device_match() is also used in order to get the IODelay values
for rev 1.0/1.1 silicon.

[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:35:21 +02:00
Kishon Vijay Abraham I
5bc2bda54d mmc: sdhci-omap: Remove setting ADMA capability in driver
sdhci can directly get ADMA capability from MMCHS_CAPA register.
Remove explicitly setting ADMA here as some instances might not have
ADMA enabled. (sdhci_read_caps() is also removed from here since
sdhci_setup_host() invokes it).

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:35:21 +02:00
Kishon Vijay Abraham I
0ec4ee3c9b mmc: sdhci-omap: Fix when capabilities are obtained from SDHCI_CAPABILITIES reg
sdhci_omap_config_iodelay_pinctrl_state() requires caps and caps2 to be
initialized (speed mode capabilities like UHS/HS200) before it is
invoked. While mmc_of_parse() initializes caps/caps2 if capabilities is
populated in device tree, it will remain uninitialized for capabilities
obtained from SDHCI_CAPABILITIES register.
Fix sdhci_omap_config_iodelay_pinctrl_state() to be used even while
getting the capabilities from SDHCI_CAPABILITIES register by invoking
sdhci_setup_host() before sdhci_omap_config_iodelay_pinctrl_state().

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:35:21 +02:00
Chaotian Jing
2a9bde19e0 mmc: mediatek: add 64G DRAM DMA support
MT2712 MSDC supports 64G DRAM DMA access, it needs update
gpd/bd structure.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:51 +02:00
Thomas Gleixner
99d02d6cd5 mmc: mmci: Remove bogus local_irq_save()
On !RT interrupt runs with interrupts disabled. On RT it's in a
thread, so no need to disable interrupts at all.
Remove the local_irq_save() invocation.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:51 +02:00
Andrew Gabbasov
3fbd432231 mmc: sdhci-esdhc-imx: Set maximum watermark levels for PIO access
While performing R/W access in PIO mode, the common SDHCI driver checks
the buffer ready status once per whole block processing. That is, after
getting an appropriate interrupt, or checking an appropriate status bit,
the driver makes buffer accesses for the whole block size (e.g. 128 reads
for 512 bytes block). This is done in accordance with SD Host Controller
Specification.

At the same time, the Ultra Secured Digital Host Controller (uSDHC), used
in i.MX6 (and, probably, earlier i.MX series too), uses a separate
Watermark Levels register, controlling the amount of data or space
available when raising status bit or interrupt. For default watermark
setting of 16 words, the controller expects (and guarantees) no more
than 16 buffer accesses after raising buffer ready status bit and
generating an appropriate interrupt. If the driver tries to access the
whole block size, it will get incorrect data at the end, and a new
interrupt will appear later, when the driver already doesn't expect it.
This happens sometimes, more likely on low frequencies, e.g. when
reading EXT_CSD at MMC card initialization phase
(which makes that initialization fail).

Such behavior of i.MX uSDHC seems to be non-compliant
to SDHCI Specification, but this is the way it works now.

In order not to rewrite the SDHCI driver PIO mode access logic,
the IMX specific driver can just set the watermark level to default
block size (128 words or 512 bytes), so that the controller behavior
will be consistent to generic specification. This patch does this
for PIO mode accesses only, restoring default values for DMA accesses
to avoid any possible side effects from performance point of view.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:50 +02:00
Vijay Viswanath
5c132323c2 mmc: sdhci-msm: support voltage pad switching
The PADs for SD card are dual-voltage that support 3v/1.8v. Those PADs
have a control signal  (io_pad_pwr_switch/mode18 ) that indicates
whether the PAD works in 3v or 1.8v.

SDHC core on msm platforms should have IO_PAD_PWR_SWITCH bit set/unset
based on actual voltage used for IO lines. So when power irq is
triggered for io high or io low, the driver should check the voltages
supported and set the pad accordingly.

Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:50 +02:00
Vijay Viswanath
ac06fba1de mmc: sdhci-msm: Add support to store supported vdd-io voltages
During probe check whether the vdd-io regulator of sdhc platform device
can support 1.8V and 3V and store this information as a capability of
platform device.

Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:49 +02:00
Sergei Shtylyov
e419768f32 mmc: renesas_sdhi_internal_dmac: add R8A77980 to whitelist
I've successfully tested eMMC on R8A77980/Condor. R8A77980 has a single
SDHI core anyway, so can't be a subject of the known RX DMA errata...

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:49 +02:00
Gustavo A. R. Silva
3f1109d132 mmc: sdhci-cadence: fix logically and structurally dead code
Currently, the code block inside the for loop will never execute more than
once, because the function returns immediately after the first iteration,
hence the execution of the code at the second iteration is structurally
dead and, code at line 281: return 0; is never reached.

Fix this by checking _ret_ before return.

Addresses-Coverity-ID: 1468009 ("Logically dead code")
Addresses-Coverity-ID: 1468002 ("Structurally dead code")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:49 +02:00
Wolfram Sang
970f2d90be mmc: host: simplify getting .drvdata
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:48 +02:00
Ryder Lee
909b345665 mmc: mediatek: use of_device_get_match_data()
The usage of of_device_get_match_data() reduce the code size a bit.

Also, the only way to call msdc_drv_probe() is to match an entry in
msdc_of_ids[], so of_id cannot be NULL.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:48 +02:00
Adrian Hunter
be17355a74 mmc: sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
Fix 3.3V voltage switch for some BYT-based Intel controllers by making use
of the ACPI DSM.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:47 +02:00
Wolfram Sang
ebca50dfae mmc: renesas_sdhi_internal_dmac: remove superfluous WARN
The WARN can never trigger because we limited the max_seg number in
renesas_sdhi_of_data already. Remove it and update the comment.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:46 +02:00
Wolfram Sang
1abf9e52ea mmc: renesas_sdhi_internal_dmac: use more generic whitelisting
Whitelisting every ES version does not scale. So, we whitelist whole
SoCs independent of ES version. If we need specific handling for an ES
version, we put it to the front, so it will be matched first.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:46 +02:00
Masaharu Hayakawa
ae275b9d60 mmc: renesas_sdhi: Fix alignment check of sg buffer
Sometimes sg->offset is not used for buffer addresses allocated by
dma_map_sg(), so alignment checks should be done on the allocated buffer
addresses. Delete the alignment check for sg->offset that is done before
dma_map_sg(). Instead, it performs the alignment check for
sg->dma_address after dma_map_sg().

Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: broke this commit in two and tidied small style issue]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[rebased to mmc/next]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:45 +02:00
Niklas Söderlund
a028b435bf mmc: renesas_sdhi: use helpers to access struct scatterlist members
Instead of directly accessing the members of struct scatterlist use the
helpers mmc_get_dma_dir() and sg_dma_address() in
renesas_sdhi_internal_dmac_start_dma(). Based on previous work by
Masaharu Hayakawa.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[rebased to mmc/next]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:45 +02:00
Kyle Roeschley
bb26b8412d mmc: sdhci-pci: Avoid 3.3V signaling on some NI 904x
On some NI 904x devices, using 3.3V signaling for extended periods of
time will physically damage the pads connected to the SDHC, eventually
causing complete failure of the controller. To work around this,
require that we avoid 3.3V signaling.

Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:44 +02:00
Kyle Roeschley
247cfe5355 mmc: core: Add capability to avoid 3.3V signaling
Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.

Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:44 +02:00
Geert Uytterhoeven
1d6efe08c8 mmc: Remove depends on HAS_DMA in case of platform dependency
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.

Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.

This simplifies the dependencies, and allows to improve compile-testing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:43 +02:00
Maxime Ripard
eef797ac13 mmc: sunxi: Drop the init / reset of the controller from set_ios
Our set_ios hook is, when the card is power up or down, either doing a full
init or put our controller back into a reset mode.

Since we're also doing that in our runtime_pm hooks, and at possibly much
more often, we can drop it from the set_ios, and either rely on our
runtime_pm hooks or our probe to do it.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:43 +02:00
Maxime Ripard
9a8e1e8cc2 mmc: sunxi: Add runtime_pm support
So far, even if our card was not in use, we didn't shut down our MMC
controller, which meant that it was still active and clocking the bus.

While this obviously means that we could save some power there, it also
creates issues when it comes to EMC control since we'll have a perfect peak
at the card clock rate.

Let's implement runtime_pm with autosuspend so that we will shut down the
controller when it's not been in use for quite some time.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:42 +02:00
Maxime Ripard
e27e1f3d04 mmc: sunxi: Move the card power configuration to a function
In order to improve readibility and reusability, let's move the card setup
to a small function called by our .set_ios hook.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:42 +02:00
Maxime Ripard
ad04d9555d mmc: sunxi: Move clock configuration to a function
In order to improve readibility and reusability, let's move the clock setup
to a small function called by our .set_ios hook.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:42 +02:00
Maxime Ripard
3f6c808e52 mmc: sunxi: Move bus width configuration to a function
In order to improve readibility and reusability, let's move the bus width
setup to a small function called by our .set_ios hook.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:41 +02:00
Maxime Ripard
0fc4c61fff mmc: sunxi: Change sunxi_mmc_init_host argument type
All the other functions in the driver take a struct sunxi_mmc_host pointer.
Let's make it consistent.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:41 +02:00
Maxime Ripard
743b819e41 mmc: sunxi: Reorder the headers
Our headers sort algorithm has had pretty chaotic results. Let's fix that.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:40 +02:00
Diwakar Sharma
8ccd66f258 mmc: core: sdio: Set SDIO clock of SDR104 to 150MHz for Marvell 8887 chip
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.

Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:39 +02:00
harish_kandiga@mentor.com
ebc5a1bf4f mmc: core: Add a new quirk for limiting clock rate
This patch adds a quirk to limit clock rate which
can be used to reduce the SDIO clock rate for some
chips with broken UHS.

Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:39 +02:00
Shawn Lin
d39b1b2abf mmc: dw_mmc: fix misleading comment in dw_mci_rk3288_set_ios
DDR52 with 8-bit mode should be handled in a different way when
requesting ciu_clk. However DDR50 is used for SDMMC/SDIO and
could never be possible with 8-bit mode. It's trival but misleading.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:38 +02:00
Masahiro Yamada
ef6b75671b mmc: sdhci-cadence: send tune request twice to work around errata
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.

Quote from the report:

Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.

Workarounds
-----------
The following are valid workarounds to resolve the issue:

1. In eMMC mode, software sends tune request twice instead of once at
   each iteration. This means that the clock phase is not changed on
   the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
   perform an almost identical procedure to eMMC, using the HRS34 Tune
   Force register.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:38 +02:00