Always read bInterfaceNumber from the current altsetting, not from the first one
available in the altsetting array. This is coming from code review, not related
to any specific bug.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support setting the rx coalesce. Then someone could change the rx
agg timeout value through ethtool.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx early size is calculated with the mtu, so it has to be
re-calculated when the mtu is changed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate USB_RX_EARLY_AGG into USB_RX_EARLY_TIMEOUT and USB_RX_EARLY_SIZE.
Replace r8153_set_rx_agg() with r8153_set_rx_early_timeout() and
r8153_set_rx_early_size().
Set the default timeout value according to the USB speed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a capability which let the hw could change the settings
automatically when the power change to ON. However, the USB reset
would reset the settings to the hw default, so the driver has to
restore the relative settings. Otherwise, it would influence the
functions of the hw, and the compatibility for the USB hub and
USB host controller.
The relative settings are as following.
- set the power down scale to 96.
- enable the power saving function of USB 2.0.
- disable the ALDPS of ECM mode.
- set burst mode depending on the burst size.
- enable the flow control of endpoint full.
- set fifo empty boundary to 32448 bytes.
- enable the function of exiting LPM when Rx OK occurs.
- set the connect timer to 1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb allocation fails once the IP header has been received, the rx state is
being set to WAIT_SYNC. The logic, though, shouldn't directly return, as the
buffer may contain a full packet, and therefore the WAIT_SYNC state needs to be
processed (resetting state to WAIT_IP, clearing rx_buf_size and re-initializing
rx_buf_missing).
So, just let the while loop continue so that in the next iteration the WAIT_SYNC
state cleanly stops the loop. The WAIT_SYNC processing will be done just after
that, only if the end of packet is flagged.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_get_protocol() has been defined and use it to replace
get_protocol().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep NETIF_F_HW_VLAN_CTAG_RX and NETIF_F_HW_VLAN_CTAG_TX at the
same line.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to accress the hw register if the device is unplugged.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace (tp->speed & LINK_STATUS) with netif_carrier_ok().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set LPM timer to 500us, except for RTL_VER_04 which doesn't link at
USB 3.0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a error occurs when submitting rx, skip the remaining submissions
and try to submit them again next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the static attribute groups and the driver data via
tty_port_register_device_attr() instead of manual device_create_file()
and device_remove_file() calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commone register macors (e.g. RSR) is too commont to drivers, it may
be conflict with the architectures (e.g. xtensa, sh).
The related warnings (with allmodconfig under xtensa):
CC [M] drivers/net/usb/sr9700.o
In file included from drivers/net/usb/sr9700.c:24:0:
drivers/net/usb/sr9700.h:65:0: warning: "RSR" redefined
#define RSR 0x06
^
In file included from ./arch/xtensa/include/asm/bitops.h:22:0,
from include/linux/bitops.h:36,
from include/linux/kernel.h:10,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/net/usb/sr9700.c:13:
./arch/xtensa/include/asm/processor.h:190:0: note: this is the location of the previous definition
#define RSR(v,sr) __asm__ __volatile__ ("rsr %0,"__stringify(sr) : "=a"(v));
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using only the usb interface number for the rfkill name, we might
have a name conflicts in case two similar hso devices are connected.
In this patch, the name of the hso rfkill interface embed the value
of a counter that is incremented each time a new rfkill interface is
added.
Suggested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hso serial devices, two cancel_work_sync were missing in the
disconnect method.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial_table is used to map the minor number of the usb serial device
to its associated context. The table is updated in the probe method and
in hso_serial_ref_free() which is called either from the tty cleanup
method or from the usb disconnect method.
This patch ensures that the serial_table is updated in the disconnect
method and no more from the cleanup method to avoid the following
potential race condition.
- hso_disconnect() is called for usb interface "x". Because the serial
port was open and because the cleanup method of the tty_port hasn't
been called yet, hso_serial_ref_free() is not run.
- hso_probe() is called and fails for a new hso serial usb interface
"y". The function hso_free_interface() is called and iterates
over the element of serial_table to find the device associated to
the usb interface context.
If the usb interface context of usb interface "y" has been created
at the same place as for usb interface "x", then the cleanup
functions are called for usb interfaces "x" and "y" and
hso_serial_ref_free() is called for both interfaces.
- release_tty() is called for serial port linked to usb interface "x"
and possibly crash because the tty_port structure contained in the
hso_device structure has been freed.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hso_serial_common_free() is called either by the cleanup
method of the tty or by the usb disconnect method.
In the former case, the usb_disconnect() has been already called
and the sysfs group associated to the device has been removed.
By calling tty_unregister directly from the usb_disconnect() method,
we avoid a warning due to the removal of the sysfs group of the usb
device.
Example of warning:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 778 at fs/sysfs/group.c:225 sysfs_remove_group+0x50/0x94()
sysfs group c0645a88 not found for kobject 'ttyHS5'
Modules linked in:
CPU: 0 PID: 778 Comm: kworker/0:3 Tainted: G W 3.18.0+ #105
Workqueue: events release_one_tty
[<c000dfe4>] (unwind_backtrace) from [<c000c014>] (show_stack+0x14/0x1c)
[<c000c014>] (show_stack) from [<c0016bac>] (warn_slowpath_common+0x5c/0x7c)
[<c0016bac>] (warn_slowpath_common) from [<c0016c60>] (warn_slowpath_fmt+0x30/0x40)
[<c0016c60>] (warn_slowpath_fmt) from [<c00ddd14>] (sysfs_remove_group+0x50/0x94)
[<c00ddd14>] (sysfs_remove_group) from [<c0221e44>] (device_del+0x30/0x190)
[<c0221e44>] (device_del) from [<c0221fb0>] (device_unregister+0xc/0x18)
[<c0221fb0>] (device_unregister) from [<c0221fec>] (device_destroy+0x30/0x3c)
[<c0221fec>] (device_destroy) from [<c01fe1dc>] (tty_unregister_device+0x2c/0x5c)
[<c01fe1dc>] (tty_unregister_device) from [<c029a428>] (hso_serial_common_free+0x2c/0x88)
[<c029a428>] (hso_serial_common_free) from [<c029a4c0>] (hso_serial_ref_free+0x3c/0xb8)
[<c029a4c0>] (hso_serial_ref_free) from [<c01ff430>] (release_one_tty+0x30/0x84)
[<c01ff430>] (release_one_tty) from [<c00271d4>] (process_one_work+0x21c/0x3c8)
[<c00271d4>] (process_one_work) from [<c0027758>] (worker_thread+0x3d8/0x560)
[<c0027758>] (worker_thread) from [<c002be4c>] (kthread+0xc0/0xcc)
[<c002be4c>] (kthread) from [<c0009630>] (ret_from_fork+0x14/0x24)
---[ end trace cb88537fdc8fa208 ]---
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for a dedicated reset work in the hso driver since
there is already a reset work foreseen in usb_interface that does
the same.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In other functions of the driver, variables of type "struct hso_serial"
are denoted by "serial" and variables of type "struct hso_device" are
denoted by "hso_dev". This patch makes the hso_free_interface()
consistent with these notations.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the rfkill interface was created, a buffer containing the name
of the rfkill node was allocated. This buffer was never freed when the
device disappears.
To fix the problem, we put the name given to rfkill_alloc() in
the hso_net structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the disconnect path, tx_buffer should freed like tx_data to avoid
a memory leak when the device disconnects.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device disappear, the function hso_disconnect() is called to
perform cleanup. In the cleanup function, hso_free_interface() calls
tty_port_tty_hangup() in view of scheduling a work to hang up the tty if
needed. If the port was not open then hso_serial_ref_free() is called
directly to cleanup everything. Otherwise, hso_serial_ref_free() is called
when the last fd associated to the port is closed.
For each open port, tty_release() will call the close method,
hso_serial_close(), which drops the last kref and call
hso_serial_ref_free() which unregisters, destroys the tty port
and finally frees the structure in which the tty_port structure
is included. Later, in tty_release(), more precisely when release_tty()
is called, the tty_port previously freed is accessed to cancel
the tty buf workqueue and it leads to a crash.
In view of avoiding this crash, we add a cleanup method that is called
at the end of the hangup process and we drop the last kref in this
function when all the ports have been closed, when tty_port is no
more needed and when it is safe to free the structure containing the
tty_port structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
No timer related function is used in this driver.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Call hex2bin() library function, instead of doing conversion here.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace tasklet with NAPI.
Add rx_queue to queue the remaining rx packets if the number of the
rx packets is more than the request from poll().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e4c7f259c5 ("USB: kaweth.c: use GFP_ATOMIC under spin_lock")
makes sure that kaweth_internal_control_msg() allocates memory with GFP_ATOMIC,
but kaweth_internal_control_msg() also calls usb_start_wait_urb()
that still allocates memory with GFP_NOIO.
The patch fixes usb_start_wait_urb() as well.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't submit the rx if the device is unplugged, stopped, or
linking down.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rtl_start_rx() from rtl_enable() and put it after calling
netif_carrier_on().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support ndo_features_check to avoid:
- the transport offset is more than the hw limitation when using hw checksum.
- the skb->len of a GSO packet is more than the limitation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some buggy firmwares export an incorrect MAC address (00:a0:c6:00:00:00). This
makes for example checking devices for random MAC addresses tricky, and you
might end up with multiple network interfaces with the same address.
This patch tries to fix, or at least improve, the situation by setting the MAC
address of devices with this firmware bug to a random address. I tested the
patch with two devices that has this firmware bug (Huawei E398 and E392), and
network traffic worked fine after changing the address.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine REALTEK_USB_DEVICE for the desired USB interface for probe().
There are three USB interfaces for the device. USB_CLASS_COMM and
USB_CLASS_CDC_DATA are for ECM mode (config #2). USB_CLASS_VENDOR_SPEC
is for the vendor mode (config #1). However, we are not interesting
in USB_CLASS_CDC_DATA for probe(), so redefine REALTEK_USB_DEVICE
to ignore the USB interface class of USB_CLASS_CDC_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a error for r8152_submit_rx(), add the remaining rx
buffers to the list. Then the remaining rx buffers could be
submitted later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The behavior of handling the returned status from r8152_submit_rx()
is almost same, so let r8152_submit_rx() deal with the error
directly. This could avoid the duplicate code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both tx and rx paths work with skb->vlan_tci, there's no need for
this function anymore. Switch users directly to __vlan_hwaccel_put_tag.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the USB VID/PID for the HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e)
Signed-off-by: Martin Hauke <mardnh@gmx.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is unplugged or !netif_running(), the workqueue
doesn't need to wake the device, and could return directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear the flag of SCHEDULE_TASKLET in bottom_half() to avoid
re-schedule the tasklet again by workqueue.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
