Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The recently merged AT91SAM9 watchdog driver uses the
AT91SAM9X_WATCHDOG config variable, whereas the original version of
the driver (and the platform support code) used AT91SAM9_WATCHDOG.
This causes the watchdog platform_device to never be registered, and
therefore the driver not to be initialized.
This patch:
- updates the platform support code to use AT91SAM9X_WATCHDOG.
- includes <linux/io.h> to fix compile error (same fix as was applied
to at91rm9200_wdt.c)
- fixes comment regarding watchdog clock-rates in at91rm9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
net: 4 bytes kernel memory disclosure in SO_BSDCOMPAT gsopt try #2
netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
bnx2: Update version to 1.9.2 and copyright.
bnx2: Fix jumbo frames error handling.
bnx2: Update 5709 firmware.
bnx2: Update 5706/5708 firmware.
3c505: do not set pcb->data.raw beyond its size
Documentation/connector/cn_test.c: don't use gfp_any()
net: don't use in_atomic() in gfp_any()
IRDA: cnt is off by 1
netxen: remove pcie workaround
sun3: print when lance_open() fails
qlge: bugfix: Add missing rx buf clean index on early exit.
qlge: bugfix: Fix RX scaling values.
qlge: bugfix: Fix TSO breakage.
qlge: bugfix: Add missing dev_kfree_skb_any() call.
qlge: bugfix: Add missing put_page() call.
qlge: bugfix: Fix fatal error recovery hang.
qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
...
When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’
defined but not used
We do not need label ‘set_32_bit_mask’ on IA64 platform,So move it to #else.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them. Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we do not set pcb->data.raw beyond its size, print an error message
and return false if we attempt to. A timout message was printed one too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no prior break occurs, cnt reaches 101 after the loop, so we are still able
to change speed when cnt has become 100.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.
The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With while (--i > 0) { ... } i reaches 0; print when lance_open() fails
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs. This can happen when a
page alloc or dma mapping fails. If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We put the skb back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We put the page back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With while (limit--) { ... } limit reaches -1, so 0 means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12646
When the temperature exceeds 32767 milli-degrees the temperature overflows
to -32768 millidegrees. These are bothe well within the -55 - +125 degree
range for the sensor.
Fix overflow in left-shift of a u8.
Signed-off-by: Ian Dall <ian@beware.dropbear.id.au>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a problem that causes I/O to a disconnected (or partially initialized)
nbd device to hang indefinitely. To reproduce:
# ioctl NBD_SET_SIZE_BLOCKS /dev/nbd23 514048
# dd if=/dev/nbd23 of=/dev/null bs=4096 count=1
...hangs...
This can also occur when an nbd device loses its nbd-client/server
connection. Although we clear the queue of any outstanding I/Os after the
client/server connection fails, any additional I/Os that get queued later
will hang.
This bug may also be the problem reported in this bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=12277
Testing would need to be performed to determine if the two issues are the
same.
This problem was introduced by the new request handling thread code ("NBD:
allow nbd to be used locally", 3/2008), which entered into mainline around
2.6.25.
The fix, which is fairly simple, is to restore the check for lo->sock
being NULL in do_nbd_request. This causes I/O to an uninitialized nbd to
immediately fail with an I/O error, as it did prior to the introduction of
this bug.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Reported-by: Jon Nelson <jnelson-kernel-bugzilla@jamponi.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <stable@kernel.org> [2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since netmos 9835 with subids 0x1014(IBM):0x0299 is now bound with
serial/8250_pci, because it has no parallel ports and subdevice id isn't
in the expected form, return -ENODEV from probe function.
This is performed in netmos preinit_hook.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With a postfix decrement t will reach -1 rather than 0, so neither the
warning nor the `goto error_out' will occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We weren't properly allocating the cmap for depths greater than 8bpp,
which caused pain for things like DirectFB. Also, we never freed the cmap
memory upon module unload..
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Marco La Porta <marco-laporta@tiscali.it>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We weren't properly allocating the cmap for depths greater than 8bpp,
which caused pain for things like DirectFB. Also, we never freed the cmap
memory upon module unload..
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Marco La Porta <marco-laporta@tiscali.it>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We weren't properly allocating the cmap for depths greater than 8bpp,
which caused pain for things like DirectFB. Also, we never freed the cmap
memory upon module unload..
[dilinger@debian.org: dropped unnecessary code and clean up patch]
[dilinger@debian.org: add error checking and handling]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here we do two things:
First, revert "iwlwifi: save PCI state before suspend, restore after
resume". That misguided patch led to being unable to use iwlwifi
devices after resume.
Next, indicate to PCI driver that the saved PCI state is valid during suspend.
We restore PCI state and enable the device when network interface is created,
similarly PCI state is saved and the device is disabled when network interface
is removed. Thus, when .suspend is called the PCI state is saved and device
is disabled. This is the case even if an interface is never created as PCI
state is saved and device disabled during .probe.
PCI driver assumes PCI state is saved in .suspend. Saving the state at this
time will save state of disabled device and thus cause problems during
resume (resuming a disabled device). We thus indicate directly to PCI
driver that current PCI saved state is valid.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Alex Riesen <fork0@users.sf.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Three people (Petr Mensik <pihhan@cipis.net>
["si" should be U+0161 U+00ED], Stephen Ho <stephenhoinhk@gmail.com>
on zd1211-devs and Ismael Ojeda Perez <iojedaperez@gmail.com>
on linux-wireless) reported success in getting TP-Link WN322G/WN422G
working by treating MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for rf
chip hardware initialization.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Petr Mensik <pihhan@cipis.net>
Tested-by: Stephen Ho <stephenhoinhk@gmail.com>
Tested-by: Ismael Ojeda Perez <iojedaperez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de> reported success
in the sourceforge zd1211 mailing list on this addition. This product ID
was supported by the vendor driver ZD1211LnxDrv 2.22.0.0 (and possibly
earlier) and it probably should have been added earlier.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under memory pressure, we may not be able to allocate a new skb for
new packets. If the allocation fails, ath5k_tasklet_rx will exit but
will leave a buffer in the list with a NULL skb, eventually triggering
a BUG_ON.
Extract the skb allocation from ath5k_rxbuf_setup() and change the
tasklet to allocate the next skb before accepting a packet.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace, x86: fix the usage of ptrace_fork()
i8327: fix outb() parameter order
x86: fix math_emu register frame access
x86: math_emu info cleanup
x86: include correct %gs in a.out core dump
x86, vmi: put a missing paravirt_release_pmd in pgd_dtor
x86: find nr_irqs_gsi with mp_ioapic_routing
x86: add clflush before monitor for Intel 7400 series
x86: disable intel_iommu support by default
x86: don't apply __supported_pte_mask to non-present ptes
x86: fix grammar in user-visible BIOS warning
x86/Kconfig.cpu: make Kconfig help readable in the console
x86, 64-bit: print DMI info in the oops trace
In dasd_device_set_timer and dasd_block_set_timer we interpret the
return value of mod_timer in a wrong way. If the timer expires in
the small window between our check of timer_pending and the call to
mod_timer, then the timer will be set, mod_timer returns zero and
we will call add_timer for a timer that is already pending.
As del_timer and mod_timer do all the necessary checking themselves,
we can simplify our code and remove the race a the same time.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently, the sunhme driver installs SBus Quattro interrupt handler
when at least one HME card was initialized correctly and at least one
Quattro card is present. This breaks when a Quattro card fails
initialization for whatever reason - IRQ is registered and OOPS happens
when it fires.
The solution, as suggested by David Miller, was to keep track which
cards of the Quattro bundles have been initialized, and request/free the
Quattro IRQ only when all four devices have been successfully
initialized.
The patch only touches SBus initialization - PCI init already resets the
card pointer to NULL on init failure.
The patch has been tested on Sun E3500 with SBus and PCI single HME
cards and one PCI Quattro HME card in a situation where any PCI card
failed init when the SBus routines tried to init them by mistake.
Additionally it replaces Quattro request_irq panic with error return -
if this card fails to work, at least let the others work.
Tested on E450 with PCI HME and PCI Quad HME.
[ Minor coding style fixups -DaveM ]
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fore 200 ATM driver fails to handle request_firmware failures and oopses
when no firmware file was found. Fix it by checking for the right return
values and propaganting the return value up.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdc pin should always be output. Initialize it as output,
so each board code does not need to do this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
bridge: Fix LRO crash with tun
IPv6: fix to set device name when new IPv6 over IPv6 tunnel device is created.
gianfar: Fix boot hangs while bringing up gianfar ethernet
netfilter: xt_sctp: sctp chunk mapping doesn't work
netfilter: ctnetlink: fix echo if not subscribed to any multicast group
netfilter: ctnetlink: allow changing NAT sequence adjustment in creation
netfilter: nf_conntrack_ipv6: don't track ICMPv6 negotiation message
netfilter: fix tuple inversion for Node information request
netxen: fix msi-x interrupt handling
de2104x: force correct order when writing to rx ring
tun: Fix unicast filter overflow
drivers/isdn: introduce missing kfree
drivers/atm: introduce missing kfree
sunhme: Don't match PCI devices in SBUS probe.
9p: fix endian issues [attempt 3]
net_dma: call dmaengine_get only if NET_DMA enabled
3c509: Fix resume from hibernation for PnP mode.
sungem: Soft lockup in sungem on Netra AC200 when switching interface up
RxRPC: Fix a potential NULL dereference
r8169: Don't update statistics counters when interface is down
...
Ira Snyder found that commit 8c7396aebb
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Bisected-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Storage: Update unusual_devs entry for Datafab KECF-USB
USB: Correct Makefile to make isp1760 buildable
USB: option: New mobile broadband modems to be supported
USB: two more usb ids for ti_usb_3410_5052
USB: ftdi_sio: unlock_kernel() on error in set_serial_info()
USB: usb-storage: add Pentax to the bad-vendor list
USB: ftdi_sio: add support for the NDI Polaris system
USB: usb-serial: fix the aircable_init failure path
USB: usb-storage: remove WARN from last-sector hacks
Revert USB: option: add Pantech cards
USB: cdc-acm.c: remove duplicate lines for MTK gps support
USB: fsl_qe_udc: Fix stalled TX requests bug
USB: fsl_qe_udc: Fix muram corruption by disabled endpoints
USB: fsl_qe_udc: Fix disconnects reporting during bus reset
USB: fsl_qe_udc: Fix QE USB controller initialization
USB: fsl_qe_udc: Fix recursive locking bug in ch9getstatus()
USB: fsl_qe_udc: Fix oops on QE UDC probe failure
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: panel: fix lcd panel driver build failure
Staging: android: fix up units in timed_gpio
Staging: android: ram_console: Disable ECC when early init is enabled and validate buffer size
Staging: at76_usb: Add support for OQO Model 01+
Staging: at76_usb: fix bugs introduced by "Staging: at76_usb: cleanup dma on stack issues"
Revert Staging: at76_usb: update drivers/staging/at76_usb w/ mac80211 port
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: Get transition latency from ACPI _PSS table
[CPUFREQ] Make ignore_nice_load setting of ondemand work as expected.
The last build fix I did messed up the units of the sysfs file.
This puts them back to be milliseconds, like they originally were.
Thanks to Juha Motorsportcom for pointing this out.
Reported-by: Juha Motorsportcom <juha_motorsportcom@luukku.com>
Cc: Mike Lockwood <lockwood@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add USB device ID for OQO 01+'s internal wireless LAN
An OQO employee mentions the chip's true identity here:-
ftp://ftp.oqo.com/unsupported/linux/OQOLinux.html
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
