This merges the radeon KMS DisplayPort and hotplug detect support.
Tested on RV635 DP card with a Dell 2408 monitor.
Conflicts:
drivers/gpu/drm/drm_fb_helper.c
This merges the upstream Intel tree and fixes up numerous conflicts
due to patches merged into Linus tree later in -rc cycle.
Conflicts:
drivers/char/agp/intel-agp.c
drivers/gpu/drm/drm_dp_i2c_helper.c
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/i915_suspend.c
- dpcp -> dpcd
- fix up dig encoder routing
- aux transaction table takes delay in 10 usec units
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Both radeon and nouveau can re-use this code so move it up a level
so they can. However the hw interfaces for aux ch are different
enough that the code to translate from mode, address, bytes
to actual hw interfaces isn't generic, so move that code into the
Intel driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Utilities to reserve, unreserve and fence a list of TTM
buffer objects in a deadlock-safe manner.
Used by the vmwgfx driver.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is intended to be used by ttm-aware drivers to
1) Block clients to inactive masters when
they try to validate buffers for GPU use.
2) Optionally block clients to the current master when
there is thrashing due to GPU memory shortage.
Used by the vmwgfx driver.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add objects needed for user-space to maintain reference counts on ttm objects.
This is used by the vmwgfx driver which allows user-space to maintain
map-counts on dma buffers, lock-counts on the ttm lock and ref-counts on
gpu surfaces, gpu contexts and dma buffer.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds a ioctl and property to allow userspace
to notify the kernel that a framebuffer has changed. Instead
of snooping the command stream this allows finer grained
tracking of which areas have changed.
The primary user for this functionality is virtual hardware
like the vmware svga device, but also Xen hardware likes to
be notify. There is also real hardware like DisplayLink and
DisplayPort that might take advantage of this ioctl.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/ttm fails to build on MIPS because "struct page" is not known:
| In file included from drivers/gpu/drm/ttm/ttm_memory.c:28:
| include/drm/ttm/ttm_memory.h:154: warning: 'struct page' declared inside parameter list
| include/drm/ttm/ttm_memory.h:154: warning: its scope is only this definition or declaration, which is probably not what you want
| include/drm/ttm/ttm_memory.h:156: warning: 'struct page' declared inside parameter list
| drivers/gpu/drm/ttm/ttm_memory.c:540: error: conflicting types for 'ttm_mem_global_alloc_page'
| include/drm/ttm/ttm_memory.h:154: error: previous declaration of 'ttm_mem_global_alloc_page' was here
| drivers/gpu/drm/ttm/ttm_memory.c:561: error: conflicting types for 'ttm_mem_global_free_page'
| include/drm/ttm/ttm_memory.h:156: error: previous declaration of 'ttm_mem_global_free_page' was here
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: stable@kernel.org
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This let's use use the linux drm headers as the canonical source for
libdrm on all platforms.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vmwgfx driver has a per master rw lock around TTM, to guarantee
mutual exclusion when needed.
This is typically when all evictable buffers are evicted due to
1) vt switch
2) master switch
3) suspend / resume.
In the multi-master case, on master switch the new master takes the
previously active master lock in write mode, and then evicts all
buffers. Any clients to previous masters will then block on that lock
when trying to validate a buffer. fbdev also acts as a virtual master
wrt this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In current vblank-wait implementation, if we turn off VGA output,
drm_wait_vblank will still wait on the disabled pipe until timeout,
because vblank on the pipe is assumed be enabled. This would cause
slow system response on some system such as moblin.
This patch resolve the issue by adding a drm helper function
drm_vblank_off which explicitly clear vblank_enabled[crtc], wake up
any waiting queue and save last vblank counter before turning off
crtc. It also slightly change drm_vblank_get to ensure that we will
will return immediately if trying to wait on a disabled pipe.
Signed-off-by: Li Peng <peng.li@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-applied for conflicts with overlay changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a GETPARAM request for checking if page flipping is supported.
Useful for the 2D driver to enable the flipping path.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We don't actually know which frame number the flip will complete on, so
userspace needs a specific flip notification to tell it when the last flip
completed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Kristian Høgsberg <krh@bitplanet.net>
Execbufs involve quite a bit of payload, to the extent that cache misses
show up in the profiles here, and a suspicion that some of those cachelines
may get evicted and then reloaded in the subsequent copy.
This is still abstracted like drm_calloc_large since we want to check for
size overflow, and because we want to choose between kmalloc and vmalloc
on the fly. cairo's interface for malloc-with-calloc's-args was used as
the model.
Signed-off-by: Eric Anholt <eric@anholt.net>
The fbdev field of the drm_framebuffer structure is always used to store
a pointer to a fb_info, so there is no reason for it to be void*.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds a page flipping ioctl to the KMS API. The ioctl takes an fb ID
and a ctrc ID and flips the crtc to the given fb at the next vblank.
The ioctl returns immediately but the flip doesn't happen until after
any rendering that's currently queued up against the new framebuffer
is done. After submitting a page flip, any execbuffer involving the
old front buffer will block until the flip is completed.
Optionally, a vblank event can be generated when the swap eventually
happens.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are a few more macros in drmP.h that are unused; DRM_GET_PRIV_SAREA,
DRM_ARRAY_SIZE, and DRM_WAITCOUNT can go away completely.
Unfortunately, DRM_COPY is still used in one place, but we can at least
move it to where it's used. It's an awful looking macro..
[akpm: fix overeagerness]
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
i915_gem_proc.c appears to have been the last user of the DRM_PROC_*
macros, and it has gone away. The macros should die as well.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds a new flag to the drmWaitVblank ioctl, which asks the drm
to return immediately and notify userspace when the specified vblank sequence
happens by sending an event back on the drm fd.
The event mechanism works with the other flags supported by the ioctls,
specifically, the vblank sequence can be specified relatively or absolutely,
and works for primary and seconday crtc.
The signal field of the vblank request is used to provide user data,
which will be sent back to user space in the vblank event.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This implements intel overlay support for kms via a device-specific
ioctl. Thomas Hellstrom brought up the idea of a general ioctl (on
dri-devel). We've reached the conclusion that such an infrastructure
only makes sense when multiple kms overlay implementations exists,
which atm don't (and it doesn't look like this is gonna change).
Open issues:
- Runs in sync with the gpu, i.e. unnecessary waiting. I've decided
to wait on this because the hw tends to hang when changing something
in this area. I left some dummy functions as infrastructure.
- polyphase filtering uses a static table.
- uses uninterruptible sleeps. Unfortunately the alternatives may
unnecessarily wedged the hw if/when we timeout too early (and
userspace only overloaded the batch buffers with stuff worth a few
secs of gpu time).
Changes since v1:
- fix off-by-one misconception on my side. This fixes fullscreen
playback.
Changes since v2:
- add underrun detection as spec'ed for i965.
- flush caches properly, fixing visual corruptions.
Changes since v4:
- fix up cache flushing of overlay memory regs.
- killed require_pipe_a logic - it hangs the chip.
Tested-By: diego.abelenda@gmail.com (on a 865G)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[anholt: Resolved against the MADVISE ioctl going in before this one]
Signed-off-by: Eric Anholt <eric@anholt.net>
This just waits until the hw passed the current ring position with
cmd execution. This slightly changes the existing i915_wait_request
function to make uninterruptible waiting possible - no point in
returning to userspace while mucking around with the overlay, that
piece of hw is just too fragile.
Also replace a magic 0 with the symbolic constant (and kill the then
superflous comment) while I was looking at the code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
I've wasted half a day hunting a bug that could easily be spotted by
gcc. Prevent this from reoccurring.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds a new flag to the drmWaitVblank ioctl, which asks the drm
to return immediately and notify userspace when the specified vblank sequence
happens by sending an event back on the drm fd.
The event mechanism works with the other flags supported by the ioctls,
specifically, the vblank sequence can be specified relatively or absolutely,
and works for primary and seconday crtc.
The signal field of the vblank request is used to provide user data,
which will be sent back to user space in the vblank event.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
conflict in radeon since new init path merged with vga arb code.
Conflicts:
drivers/gpu/drm/radeon/radeon.h
drivers/gpu/drm/radeon/radeon_asic.h
drivers/gpu/drm/radeon/radeon_device.c
The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.
this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.
Tested on r100/r600/i945.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also add single crtc for RN50 chips.
changes in v2:
fix vblank init to respect single crtc flag
fix r100 mode bandwidth to respect single crtc flag
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (25 commits)
drm/radeon/kms: Convert R520 to new init path and associated cleanup
drm/radeon/kms: Convert RV515 to new init path and associated cleanup
drm: fix radeon DRM warnings when !CONFIG_DEBUG_FS
drm: fix drm_fb_helper warning when !CONFIG_MAGIC_SYSRQ
drm/r600: fix memory leak introduced with 64k malloc avoidance fix.
drm/kms: make fb helper work for all drivers.
drm/radeon/r600: fix offset handling in CS parser
drm/radeon/kms/r600: fix forcing pci mode on agp cards
drm/radeon/kms: fix for the extra pages copying.
drm/radeon/kms/r600: add support for vline relocs
drm/radeon/kms: fix some bugs in vline reloc
drm/radeon/kms/r600: clamp vram to aperture size
drm/kms: protect against fb helper not being created.
drm/r600: get values from the passed in IB not the copy.
drm: create gitignore file for radeon
drm/radeon/kms: remove unneeded master create/destroy functions.
drm/kms: start adding command line interface using fb.
fb: change rules for global rules match.
drm/radeon/kms: don't require up to 64k allocations. (v2)
drm/radeon/kms: enable dac load detection by default.
...
Trivial conflicts in drivers/gpu/drm/radeon/radeon_asic.h due to adding
'->vga_set_state' function pointers.
This initialises the fb helper with the connector helper,
so that the fb cmdline code works for intel as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>
[note this requires an fb patch posted to linux-fbdev-devel already]
This uses the normal video= command line option to control the kms
output setup at boot time. It is used to override the autodetection
done by kms.
video= normally takes a framebuffer as the first parameter, in kms
it will take a connector name, DVI-I-1, or LVDS-1 etc. If no output
connector is specified the mode string will apply to all connectors.
The mode specification used will match down the probed modes, and if
no mode is found it will add a CVT mode that matches.
video=1024x768 - all connectors match a 1024x768 mode or add a CVT on
video=VGA-1:1024x768, VGA-1 connector gets mode only.
The same strings as used in current fb modedb.c are used, except I've
added three more letters, e, D, d, e = enable, D = enable Digital,
d = disable, which allow a connector to be forced into a certain state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (57 commits)
drm/i915: Handle ERESTARTSYS during page fault
drm/i915: Warn before mmaping a purgeable buffer.
drm/i915: Track purged state.
drm/i915: Remove eviction debug spam
drm/i915: Immediately discard any backing storage for uneeded objects
drm/i915: Do not mis-classify clean objects as purgeable
drm/i915: Whitespace correction for madv
drm/i915: BUG_ON page refleak during unbind
drm/i915: Search harder for a reusable object
drm/i915: Clean up evict from list.
drm/i915: Add tracepoints
drm/i915: framebuffer compression for GM45+
drm/i915: split display functions by chip type
drm/i915: Skip the sanity checks if the current relocation is valid
drm/i915: Check that the relocation points to within the target
drm/i915: correct FBC update when pipe base update occurs
drm/i915: blacklist Acer AspireOne lid status
ACPI: make ACPI button funcs no-ops if not built in
drm/i915: prevent FIFO calculation overflows on 32 bits with high dotclocks
drm/i915: intel_display.c handle latency variable efficiently
...
Fix up trivial conflicts in drivers/gpu/drm/i915/{i915_dma.c|i915_drv.h}
In order to correctly prevent the invalid reuse of a purged buffer, we
need to track such events and warn the user before something bad
happens.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (133 commits)
drm/vgaarb: add VGA arbitration support to the drm and kms.
drm/radeon: some r420s have a CP race with the DMA engine.
drm/radeon/r600/kms: rv670 is not DCE3
drm/radeon/kms: r420 idle after programming GA_ENHANCE
drm/radeon/kms: more fixes to rv770 suspend/resume path.
drm/radeon/kms: more alignment for rv770.c with r600.c
drm/radeon/kms: rv770 blit init called too late.
drm/radeon/kms: move around new init path code to avoid posting at init
drm/radeon/r600: fix some issues with suspend/resume.
drm/radeon/kms: disable VGA rendering engine before taking over VRAM
drm/radeon/kms: Move radeon_get_clock_info() call out of radeon_clocks_init().
drm/radeon/kms: add initial connector properties
drm/radeon/kms: Use surfaces for scanout / cursor byte swapping on big endian.
drm/radeon/kms: don't fail if we fail to init GPU acceleration
drm/r600/kms: fixup number of loops per blit calculation.
drm/radeon/kms: reprogram format in set base.
drm/radeon: avivo chips have no separate int bit for display
drm/radeon/r600: don't do interrupts
drm: fix _DRM_GEM addmap error message
drm: update crtc x/y when only fb changes
...
Fixed up trivial conflicts in firmware/Makefile due to network driver
(cxgb3) and drm (mga/r128/radeon) firmware being listed next to each
other.
VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.
VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.
This patch comes from Fedora rawhide kernel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
fix the following 'make includecheck' warning:
include/drm/drm_memory.h: linux/vmalloc.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247068169.4382.99.camel@ht.satnam>
Acked-by: Dave Airlie <airlied@redhat.com>
Userspace can query if acceleration is working or not true get
info ioctl and could fallback to software if for some reason
kernel failed to initialize KMS. This should allow to give a
working KMS setup in all case (even with non functionning accel).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Similar to the madvise() concept, the application may wish to mark some
data as volatile. That is in the event of memory pressure the kernel is
free to discard such buffers safe in the knowledge that the application
can recreate them on demand, and is simply using these as a cache.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
