The AF_IEEE802154 sockaddr looks like this:
struct sockaddr_ieee802154 {
sa_family_t family; /* AF_IEEE802154 */
struct ieee802154_addr_sa addr;
};
struct ieee802154_addr_sa {
int addr_type;
u16 pan_id;
union {
u8 hwaddr[IEEE802154_ADDR_LEN];
u16 short_addr;
};
};
On most architectures there will be implicit structure padding here,
in two different places:
* In struct sockaddr_ieee802154, two bytes of padding between 'family'
(unsigned short) and 'addr', so that 'addr' starts on a four byte
boundary.
* In struct ieee802154_addr_sa, two bytes at the end of the structure,
to make the structure 16 bytes.
When calling recvmsg(2) on a PF_IEEE802154 SOCK_DGRAM socket, the
ieee802154 stack constructs a struct sockaddr_ieee802154 on the
kernel stack without clearing these padding fields, and, depending
on the addr_type, between four and ten bytes of uncleared kernel
stack will be copied to userspace.
We can't just insert two 'u16 __pad's in the right places and zero
those before copying an address to userspace, as not all architectures
insert this implicit padding -- from a quick test it seems that avr32,
cris and m68k don't insert this padding, while every other architecture
that I have cross compilers for does insert this padding.
The easiest way to plug the leak is to just memset the whole struct
sockaddr_ieee802154 before filling in the fields we want to fill in,
and that's what this patch does.
Cc: stable@vger.kernel.org
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch make to use the same naming convention that mac802154
tracing follows and fixes the format specifier for extended addr.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets the acknowledge request bit inside the 802.15.4 mac
header when frame retries is 0 or above. The other frame retries value
which is -1 indicates that the transmitter doesn't care about an
acknowledge frame which will be ignored after transmitting if the node
sends anyway an ack frame after receiving. This is currently unnecessary
traffic if the max frame retries parameter is -1.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Refuse to allow setting an EUI-64 group address as an interface
address, as those are not valid station addresses.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- checkpatch fixes
- code cleanup
- debugfs component is now compiled only if DEBUG_FS is selected
- update copyright years
- disable by default not-so-user-safe features
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=2UBm
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- checkpatch fixes
- code cleanup
- debugfs component is now compiled only if DEBUG_FS is selected
- update copyright years
- disable by default not-so-user-safe features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove automatic variable 'err' in register_netevent_notifier() and
return the result of atomic_notifier_chain_register() directly.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, they are:
1) default CONFIG_NETFILTER_INGRESS to y for easier compile-testing of all
options.
2) Allow to bind a table to net_device. This introduces the internal
NFT_AF_NEEDS_DEV flag to perform a mandatory check for this binding.
This is required by the next patch.
3) Add the 'netdev' table family, this new table allows you to create ingress
filter basechains. This provides access to the existing nf_tables features
from ingress.
4) Kill unused argument from compat_find_calc_{match,target} in ip_tables
and ip6_tables, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete jump to a label on the next line, when that label is not
used elsewhere.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier l;
@@
-if (...) goto l;
-l:
// </smpl>
Also remove the unnecessary ret variable.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-05-28
Here's a set of patches intended for 4.2. The majority of the changes
are on the 802.15.4 side of things rather than Bluetooth related:
- All sorts of cleanups & fixes to ieee802154 and related drivers
- Rework of tx power support in ieee802154 and its drivers
- Support for setting ieee802154 tx power through nl802154
- New IDs for the btusb driver
- Various cleanups & smaller fixes to btusb
- New btrtl driver for Realtec devices
- Fix suspend/resume for Realtek devices
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As sock refcnt is taken when sock timer is started in
sk_reset_timer(), the sock refcnt should be put when sock timer
to be deleted is in pending state no matter what "probing_state"
value of tipc sock is.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
classic BPF already exposes skb->dev->ifindex via SKF_AD_IFINDEX extension.
Allow eBPF program to access it as well. Note that classic aborts execution
of the program if 'skb->dev == NULL' (which is inconvenient for program
writers), whereas eBPF returns zero in such case.
Also expose the 'skb_iif' field, since programs triggered by redirected
packet need to known the original interface index.
Summary:
__skb->ifindex -> skb->dev->ifindex
__skb->ingress_ifindex -> skb->skb_iif
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to b1cb59cf2efe(net: sysctl_net_core: check SNDBUF
and RCVBUF for min length). I don't think too small values can cause
crashes in the case of udp and tcp, but I've seen this set to too
small values which triggered awful performance. It also makes the
setting consistent across all the wmem/rmem sysctls.
Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove these unnecessary brackets inside a condition.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This patch tries to increase code readability by negating the first if
block and rearranging some of the other conditional blocks. This way we
save an indentation level, we also save some allocation that is not
necessary for one of the conditions.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The current default settings for optional features in batman-adv seems to
be based around the idea that the user only compiles what he requires. They
will automatically enabled when they are compiled in. For example the
network coding part of batman-adv is by default disabled in the out-of-tree
module but will be enabled when the code is compiled during the module
build.
But distributions like Debian just enable all features of the batman-adv
kernel module and hope that more experimental features or features with
possible negative effects have to be enabled using some runtime
configuration interface.
The network_coding feature can help in specific setups but also has
drawbacks and is not disabled by default in the out-of-tree module.
Disabling by default in the runtime config seems to be also quite sane.
The bridge_loop_avoidance is the only feature which is disabled by default
but may be necessary even in simple setups. Packet loops may even be
created during the initial node setup when this is not enabled. This is
different than STP on bridges because mesh is usually used on Adhoc WiFi.
Having two nodes (by accident) in the same LAN segment and in the same mesh
network is rather common in this situation.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This string pointer is later assigned to a constant string, so it should
be defined constant at the beginning.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This function returns bool values, so it should be defined to return
them instead of the whole int range.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Directly return error values. No need to use a return variable.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The whole Makefile is sorted, just the multicast rule is not at the
right position.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Instead of hiding the normal function flow inside an if block, we should
just put the error handling into the if block.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Normally the debugfs framework will return error pointer with -ENODEV
for function calls when DEBUG_FS is not set.
batman does not notice this error code and continues trying to create
debugfs files and executes more code. We can avoid this code execution
by disabling compiling debugfs.c when DEBUG_FS is not set.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The fragment queueing code now validates the total_size of each fragment,
checks when enough fragments are queued to allow to merge them into a
single packet and if the fragments have the correct size. Therefore, it is
not required to have any other parameter for the merging function than a
list of queued fragments.
This change should avoid problems like in the past when the different skb
from the list and the function parameter were mixed incorrectly.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The fragmentation code was replaced in
610bfc6bc9 ("batman-adv: Receive fragmented
packets and merge") by an implementation which handles the queueing+merging
of fragments based on their size and the total_size of the non-fragmented
packet. This total_size is announced by each fragment. The new
implementation doesn't check if the the total_size information of the
packets inside one chain is consistent.
This is consistency check is recommended to allow using any of the packets
in the queue to decide whether all fragments of a packet are received or
not.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2015-05-28
1) Remove xfrm_queue_purge as this is the same as skb_queue_purge.
2) Optimize policy and state walk.
3) Use a sane return code if afinfo registration fails.
4) Only check fori a acquire state if the state is not valid.
5) Remove a unnecessary NULL check before xfrm_pol_hold
as it checks the input for NULL.
6) Return directly if the xfrm hold queue is empty, avoid
to take a lock as it is nothing to do in this case.
7) Optimize the inexact policy search and allow for matching
of policies with priority ~0U.
All from Li RongQing.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 07f4c90062 ("tcp/dccp: try to not exhaust
ip_local_port_range in connect()") it is advised to have an even number
of ports described in /proc/sys/net/ipv4/ip_local_port_range
This means start/end values should have a different parity.
Let's warn sysadmins of this, so that they can update their settings
if they want to.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__inet_hash_connect() does not use its third argument (port_offset)
if socket was already bound to a source port.
No need to perform useless but expensive md5 computations.
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A long standing problem on busy servers is the tiny available TCP port
range (/proc/sys/net/ipv4/ip_local_port_range) and the default
sequential allocation of source ports in connect() system call.
If a host is having a lot of active TCP sessions, chances are
very high that all ports are in use by at least one flow,
and subsequent bind(0) attempts fail, or have to scan a big portion of
space to find a slot.
In this patch, I changed the starting point in __inet_hash_connect()
so that we try to favor even [1] ports, leaving odd ports for bind()
users.
We still perform a sequential search, so there is no guarantee, but
if connect() targets are very different, end result is we leave
more ports available to bind(), and we spread them all over the range,
lowering time for both connect() and bind() to find a slot.
This strategy only works well if /proc/sys/net/ipv4/ip_local_port_range
is even, ie if start/end values have different parity.
Therefore, default /proc/sys/net/ipv4/ip_local_port_range was changed to
32768 - 60999 (instead of 32768 - 61000)
There is no change on security aspects here, only some poor hashing
schemes could be eventually impacted by this change.
[1] : The odd/even property depends on ip_local_port_range values parity
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting the current cca ed level value over
nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds information about the current cca ed level when the phy
is dumped over nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We currently always send fragments without DF bit set.
Thus, given following setup:
mtu1500 - mtu1500:1400 - mtu1400:1280 - mtu1280
A R1 R2 B
Where R1 and R2 run linux with netfilter defragmentation/conntrack
enabled, then if Host A sent a fragmented packet _with_ DF set to B, R1
will respond with icmp too big error if one of these fragments exceeded
1400 bytes.
However, if R1 receives fragment sizes 1200 and 100, it would
forward the reassembled packet without refragmenting, i.e.
R2 will send an icmp error in response to a packet that was never sent,
citing mtu that the original sender never exceeded.
The other minor issue is that a refragmentation on R1 will conceal the
MTU of R2-B since refragmentation does not set DF bit on the fragments.
This modifies ip_fragment so that we track largest fragment size seen
both for DF and non-DF packets, and set frag_max_size to the largest
value.
If the DF fragment size is larger or equal to the non-df one, we will
consider the packet a path mtu probe:
We set DF bit on the reassembled skb and also tag it with a new IPCB flag
to force refragmentation even if skb fits outdev mtu.
We will also set DF bit on each fragment in this case.
Joint work with Hannes Frederic Sowa.
Reported-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_skb_dst_mtu is small inline helper, but its called in several places.
before: 17061 44 0 17105 42d1 net/ipv4/ip_output.o
after: 16805 44 0 16849 41d1 net/ipv4/ip_output.o
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds transmission power setting support for IEEE-802.15.4
devices via nl802154.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We used to get this indirectly I supposed, but no longer do.
Either way, an explicit include should have been done in the
first place.
net/ipv4/fib_trie.c: In function '__node_free_rcu':
>> net/ipv4/fib_trie.c:293:3: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(n);
^
net/ipv4/fib_trie.c: In function 'tnode_alloc':
>> net/ipv4/fib_trie.c:312:3: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
return vzalloc(size);
^
>> net/ipv4/fib_trie.c:312:3: warning: return makes pointer from integer without a cast
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By making sure sk->sk_gso_max_segs minimal value is one,
and sysctl_tcp_min_tso_segs minimal value is one as well,
tcp_tso_autosize() will return a non zero value.
We can then revert 843925f33f
("tcp: Do not apply TSO segment limit to non-TSO packets")
and save few cpu cycles in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tcp ehash table is constrained to a very small number of buckets
(eg boot parameter thash_entries=128), then we can crash if spinlock
array has more entries.
While we are at it, un-inline inet_ehash_locks_alloc() and make
following changes :
- Budget 2 cache lines per cpu worth of 'spinlocks'
- Try to kmalloc() the array to avoid extra TLB pressure.
(Most servers at Google allocate 8192 bytes for this hash table)
- Get rid of various #ifdef
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit dd3f9e70f5
("tipc: add packet sequence number at instant of transmission") we
made a change with the consequence that packets in the link backlog
queue don't contain valid sequence numbers.
However, when we create a link protocol message, we still use the
sequence number of the first packet in the backlog, if there is any,
as "next_sent" indicator in the message. This may entail unnecessary
retransissions or stale packet transmission when there is very low
traffic on the link.
This commit fixes this issue by only using the current value of
tipc_link::snd_nxt as indicator.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the handling to call cca mode setting. If the phy isn't
flag then the driver doesn't support this setting.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
mac802154_mlme_start_req() calls
ieee802154_mlme_ops(dev)->llsec->set_params() on the net_device
passed into it, however, this net_device will always be a mac802154
net_device, so just call mac802154_set_params() directly instead.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ieee802154_get_dev() only returns devices that have dev->type ==
ARPHRD_IEEE802154, therefore, there is no need to check this again
in raw_bind().
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the past, 802.15.4 interfaces and 6LoWPAN interfaces used the
same dev->type (ARPHRD_IEEE802154), and 802.15.4 interfaces were
distinguished from 6LoWPAN interfaces by their differing dev->mtu.
6LoWPAN interfaces have their own ARPHRD type now, so there is no
longer any need to check dev->mtu to distinguish 802.15.4 devices
from 6LoWPAN devices.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This allows us to create netdev tables that contain ingress chains. Use
skb_header_pointer() as we may see shared sk_buffs at this stage.
This change provides access to the existing nf_tables features from the ingress
hook.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds the internal NFT_AF_NEEDS_DEV flag to indicate that you must
attach this table to a net_device.
This change is required by the follow up patch that introduces the new netdev
table.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
