Add ramp functions for the headset and handsfree outputs
in order to reduce the pops during power on/off sequences.
In order to give more control to volume ramp, step size and delay
between steps can be specified.
The patches are based on wm8350 implementation from Liam
Girdwood.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Gain for LineInAmp Right uses LINEGAIN[5:3], which means that
offset for right channel should be 4.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some gains were incorrectly configured for dB values.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
After coming back from suspend, the timeout waiting for Phoenix
chip to complete its power up sequence is not enough, which leaves
the codec cache value for some registers in an outdated state.
Increase the timeout value to wait for the power up sequence
to correclty complete.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Enable plug detection interrupt mask in order to get headset
PLUGINT/UNPLUGINT interrupts.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
On Phoenix 1.1, the INTID register default value is an invalid
one, causing the interrupt handler to think the phoenix power on
sequence is ready before it actually finishes.
This causes some i2c errors when trying to configure twl.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Phoenix 1.1 supports automatic power on sequence, a
verification is added to use it with new revision of
the chip.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The mux control has 4 elements not 3
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The twl6040 can support more sample rates other than 88.2 and 96k.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch moves all the PCM error handling for clock config
out of trigger() and startup() and into prepare().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch restores the CODEC bias level at resume().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for the twl6040 headset and handset
MUX controls.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Multiples interrupts can be received. The irq handler is modified
to attend all of them.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Update the codec to use the new twl core register macros
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use jack framework to enable detection for the headset microphone
and stereo output in the sdp4430.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for reporting twl6040 headset and
handset jack events.
The machine driver retrieves and report the status through
twl6040_hs_jack_detect.
A workq is used to debounce of the irq.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
twl4030 series of codecs supports S32_LE with msbits=24.
Replace the S24_LE with S32_LE format, and add constraint
for 24msbit in case of 32 S32_LE format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Remove redundant parentheses/spaces in the use of the sizeof
operator.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This helps ensure that the ramp logic is reset when powering back up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In some cases it was not possible to follow the appropiate power
ON/OFF sequence like in cases where the PGA needs to be enabled
before the driver and disabled before the PGA for pop reduction.
Add a widget to support output driver (speaker, haptic, vibra, etc)
drivers where power ON/OFF ordering is important.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
soc_unregister_ac97_dai_link() takes a CODEC as an argument, not a
rtd like the registration function, so give it what it's looking for.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix "ASoC: Fix bias power down of non-DAPM codec" for 3.6.37 will cause a
build error when merging into ASoC for-2.6.38. Fix the issue by doing a
change that commit ce6120c "ASoC: Decouple DAPM from CODECs" would do.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently bias of non-DAPM codec will be powered down (standby/off) whenever
there is a stream stop. This is wrong in simultaneous playback/capture since
the bias is put down immediately after stopping the first stream.
Fix this by using the codec->active count when figuring out the needed bias
level after stream stop.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The compiler really ought to have been warning about unreferenced
variables...
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
flush_scheduled_work() is deprecated and scheduled to be removed.
* cancel[_delayed]_work() + flush_scheduled_work() ->
cancel[_delayed]_work_sync().
* wm8350, wm8753 and soc-core use custom code to cancel a delayed
work, execute it immediately if it was pending and wait for its
completion. This is equivalent to flush_delayed_work_sync(). Use
it instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide the user with a boolean control then automatically select
the deemphasis filter most closely matching the sample rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We're already flagged as using symmetric rates so we don't need to
have a custom implementation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the following scenario has been followed:
1. Enable analog bypass
amixer sset 'Analog Left Bypass' on
amixer sset 'Analog Right Bypass' on
2. Start playback
aplay -fdat -d3 /dev/zero
After the playback stopped (3 sec), and the soc timeout (5 sec),
the digital parts of the codec will remain powered up.
This means that the DAI clocks are continue to run, the
oscillator remain operational, etc.
Use the SND_SOC_DAPM_POST_PMD widget to get notification
about the stopped stream, and power down the digital
part of the codec.
If the analog bypass is enabled, than the codec will remain in
BIAS_ON level, and things will work correctly.
In case, if the bypass is disabled, than the codec will
fall to BIAS_STANDBY than to BIAS_OFF level, as it used
to.
The digital part of DAC33 is initialized at every stream start
(DAPM_PRE:PRE_PMU event), so subsequent streams (within 5 sec)
will have working DAI.
When the codec is coming out from BIAS_OFF, the full power-up
sequence followed by the same DAPM_PRE widget event will power up
the digital part.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add glue driver to make s3c24xx-i2s and uda1380 produce some sound on
H1940.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The oversampling rate of the DAC and ADC can be controlled to optimise
for either low power consumption or maximum performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Tune the FLL gain for optimal performance according to evaluation
results.
Signed-off-by: Mario Becroft <mb@gem.win.co.nz>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Changes to both I2S and PCM code:
- Rates list extended up to 96kHz, it's tested on EDB9302 and works for both capture and
playback.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acc to WM8580 manual, the default value for R8 is 0x10, not 0x1c.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Deemphasis control's .get callback should update control's value instead
of returning it - return value of callback function is used for indicating
error or success of operation.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Add FM stereo pins to the machine driver and add them as a
dapm widget.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix the compilation error introduced by patch:
ASoC: tlv320dac33: Avoid multiple soft power up
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The power for the DACs need to be enabled, even when only
the analog bypass is in use with the codec, otherwise
the audio is going to be distorted.
Make sure that the DACs are powered all the time, when
there is audio activity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use better name for the widget, and remove the 'Power'
from it's name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Uk Kim <w0806.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8994 supports mono signals - enable this in the driver. With DSP
mode an automatic data channel selector is available, activate this
when in mono mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In case the codec driver did not provide a read/write function,
codec->driver->read|write will be NULL. Ensure that we use the one
specified in codec->read|write to avoid oopsing when we access
the debugfs entries. This is achieved by using snd_soc_read() and
snd_soc_write().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
