Such a hardcoded address can cause a checkstop or machine check if
the driver is in the kernel but the address is not acknowledged.
Both drivers allow an address to be specified as either a module
parameter or config option. Any future powerpc board should either
use one of these methods or find the address in the device tree.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Also remove mtd->ecclayout and mtd->oobavail assignments, mtd core
handles this all by itself.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There's no reason to prevent the Atmel NAND driver from
building as a module.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ALE signal isn't correctly wired up to the ECC controller on the
AP7000, so it starts calculating ECC during the address cycles.
Work around this by resetting the ECC controller between the address and
data cycles.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This uses __raw_{read,write}s{b,w}() primitives to access data on NAND
chips for more efficient I/O.
On an arm926 with memory clocked at 100 MHz, this reduced the elapsed time
for a 64 MiB read by 16%. ("dd" /dev/mtd0 to /dev/null, with an 8-bit
NAND using hardware ECC and 128KiB blocksize.)
Also some minor section tweaks:
- Use platform_driver_probe() so no pointer to probe() lingers
after that code has been removed at run-time.
- Use __exit and __exit_p so the remove() code will normally be
removed by the linker.
Since these buffer read/write calls are new, this increases the runtime
code footprint (by 88 bytes on my build, after the section tweaks).
[haavard.skinnemoen@atmel.com: rebase onto atmel_nand rename]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Update CM-X270 NAND flash driver to use gpio_lib.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some SoCs need a different chip_delay value.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Make the atmel_nand driver selectable on AVR32, and update the Kconfig
help text to reflect this.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This fixes several bugs in the atmel_nand_probe() error path, including
at least one memory leak.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The AT91 NAND driver needs just a few tiny modifications to work on
AVR32 as well. Rename it atmel_nand to reflect this.
Also move the ECC register definitions into drivers/mtd/nand since they
are only useful to the atmel_nand driver, and get rid of the useless
filename at the top of each file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
No point in using an AT91-specific GPIO API when the generic API works
just as well.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
WARNING: drivers/mtd/nand/built-in.o(.devinit.text+0x114): Section mismatch
in reference from the function fsl_elbc_ctrl_probe() to the function
.devexit.text:fsl_elbc_ctrl_remove()
__devinit functions should not call functions with __devexit. Since probe
function calls remove in case of errors, we want to remove __devexit
attribute from it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix nandsim build error, missing #include:
linux-next-20080605/drivers/mtd/nand/nandsim.c: In function 'divide':
linux-next-20080605/drivers/mtd/nand/nandsim.c:462: error: implicit declaration of function 'do_div'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The changelog on the driver is superflous given this
is being kept under revision control. Remove the other
cruft in the header and update the copyright and the
supported device list.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a minor problem with what should have been
debug output by changing printk() to dev_dbg()
inside s3c2410_nand_update_chip().
Thanks to David Woodhouse for pointing this out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Amend nandsim so that it does not assume 32-bit flash size.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use at91_nand_enable(), at91_nand_disable() to manipulate enable_pin.
No functional changes.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This driver did not control NCE signal during normal operations (only
enable NCE on probing and disable NCE on removing). This patch make
NCE signal inactive on idle state.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The sam926x docs allegedly don't list an "ECC_PARITY" field, and the
header files in the upstream kernel don't have it either.
Masking with it was useless anyway, so just remove it.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is a patch to use the hardware ECC controller of
the AT91SAM9260 and AT91SAM9263 for the AT91 nand.
On AT91 NAND, there's now a choice between ECC soft,
ECC hard or no ECC (for debug).
It has been tested on AT91SAM9263 with 8 bits large
and small page NAND.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
With modern systems using bus-hold instead of bus pull-up, it can
often lead to erroneous reporting of NAND devices where there are
none. Do a double probe to ensure that the result we got the first
time is repeatable, and if it is not then return that there is no
chip there.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support to disable ECC checking for a given chip
when passed by the board via the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for the ECC layout to be passed via the
platform data specified by the board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If a block's ecc field is all 0xff, then ignore the ECC
correction. This is for systems where some of the blocks,
such as the initial cramfs are written without ECC and
need to be loaded on start.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This adds support for using large page NAND devices
with the S3C24XX NAND controller. This also adds the
file Documentation/arm/Samsung-S3C24XX/NAND.txt to
describe the differences.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Commit 03680b1e00 incorrectly
was assuming S3C2410_NFCONF was being used to select the
NAND chip. Fix this error by ising the sel_reg.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch sets mtd->name to the platform bus ID in the plat_nand
driver, so that you can specify partitions readily with mtdparts=.
Currently it relies on nand_base filling in the name from the device,
which results in names like "NAND 256MiB 3,3V 8-bit", that you can't
use with cmdlineparts.
Signed-off-by: Hamish Moffatt <hamish@cloud.net.au>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a race condition in fsl_elbc_run_command
Fix incorrect usage of clearbits32 that bashed option register
Remove work around for bashed register
Signed-off-by: Mike Hench <mhench@elutions.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently fsl_elbc_nand doesn't initialize mtd->name, and this causes
nand_get_flash_type() to assign name that is equal to chip type, like
this:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "NAND 32MiB 3,3V 8-bit"
mtd0 is physmap_of flash (normal name), and mtd1 is fsl_elbc_nand.
Despite inconsistency, with mtd name like this specifying paritions
from the kernel command line becomes a torture (though, I didn't tried
and not sure if mtdparts= can handle spaces at all). Plus, this causes
real bugs when multiple fsl_elbc_nand chips registered.
With this patch applied fsl_elbc_nand chip will have proper name:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "e0600000.flash"
p.s. We can't use priv->dev->bus_id as in physmap_of, because
fsl_elbc_nand pretends to be a localbus controller, so its bus_id is
"address.localbus", which is incorrect and thus will also not work
for multiple chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is very simple driver, NAND is connected through localbus,
and User-Programmable Machine is doing various adjustments to
speak NAND. No special efforts needed to do read and write cycles,
though to control ALE and CLE phases, we ask UPM to generate exact
pre-programmed signals on the localbus lines.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is preliminary since:
1. It supports only _one_ chip select at the moment. As there is no
existing platforms available using two chip selects of the NAND
controller, it shall really not include code for supporting the
2nd chip select for now, as such code cannot be verified.
2. It resorts to the default and simpliest memory based badblock
table
3. Only limited types of nand flash are currently supported. Most
PXA3xx processors come with on-chip NAND flash dies, so there
isn't much flexibility for other types of NAND.
4. The NAND controller should be configured to detect the device's
ID, thus making it difficult to use nand_scan_ident() to assist
the detection process (though it's not impossible)
TODO: fix all the above limitations of cuz :-)
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Previously, a READ command was erroneously issued rather than SEQIN.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The part_probes[] should be static.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MTD NAND
platform drivers, to re-enable auto loading.
NOTE: at91_nand for some reason disallows modular builds. I'm assuming that's
just an oversight that will be fixed.
[dbrownell@users.sourceforge.net: minor fix]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I found this while I was looking how the rs_lib is working. The rs_decoder is
initialized _after_ the nand core code read the BBT table and _after_ the
partition table has been added. The driver has a private BBT description
which is in located in flash data so we Ooops if there is a bit flip _or_ if a
bit flips while reading the partition table.
This patch moves the initialization of the rs_lib before the first possible
access by nand core.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jörn Engel <joern@wh.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make the needlessly global part_probes[] static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
This is needed to support other localbus peripherals, such as
NAND on FSL UPM.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This has been forgotten in commit f5bbdacc41 ("[MTD] NAND Modularize
read function") and nobody compiled the driver.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joern Engel <joern@wh.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implements kernel command line partitioning support for the CS5535/CS5536 chipsets driver.
For that the following is done:
* cs553x_cleanup(): try the cleanup for all chip selects to not leak memory
* Assign a unique name for each chip select to be separately addressable in the command line mtd-id portion(s)
* Use the already defined PIN_OPT_IDE constant where appropriate for readability
* Include command line partitioning support when CONFIG_MTD_PARTS is set
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* git://git.infradead.org/mtd-2.6: (120 commits)
[MTD] Fix mtdoops.c compilation
[MTD] [NOR] fix startup lock when using multiple nor flash chips
[MTD] [DOC200x] eccbuf is statically defined and always evaluate to true
[MTD] Fix maps/physmap.c compilation with CONFIG_PM
[MTD] onenand: Add panic_write function to the onenand driver
[MTD] mtdoops: Use the panic_write function when present
[MTD] Add mtd panic_write function pointer
[MTD] [NAND] Freescale enhanced Local Bus Controller FCM NAND support.
[MTD] physmap.c: Add support for multiple resources
[MTD] [NAND] Fix misparenthesization introduced by commit 78b65179...
[MTD] [NAND] Fix Blackfin NFC ECC calculating bug with page size 512 bytes
[MTD] [NAND] Remove wrong operation in PM function of the BF54x NFC driver
[MTD] [NAND] Remove unused variable in plat_nand_remove
[MTD] Unlocking all Intel flash that is locked on power up.
[MTD] [NAND] at91_nand: Make mtdparts option can override board info
[MTD] mtdoops: Various minor cleanups
[MTD] mtdoops: Ensure sequential write to the buffer
[MTD] mtdoops: Perform write operations in a workqueue
[MTD] mtdoops: Add further error return code checking
[MTD] [NOR] Test devtype, not definition in flash_probe(), drivers/mtd/devices/lart.c
...
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is no suspend/resume operation in NFC driver at all, currently.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
With CONFIG_MTD_PARTITIONS not set, got this:
drivers/mtd/nand/plat_nand.c:113: warning: unused variable 'pdata'
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Call parse_mtd_partitions before checking board's partition_info, so
that "mtdparts=" option can override board's default setting.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The single-bit error correction was, well, incorrect. For determing which
bit to correct it was using P1' P2' P4' P8' instead of P1 P2 P4 P8, and
it was using P16' P32' P64' P128' P256' P512' P1024' P2048' instead of
P16 P32 P64 P128 P256 P512 P1024 P2048.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If there were multiple bit errors in the data s3c2410_nand_correct_data()
was returning 0 (no error) instead of -1, so the upper layers (like JFFS2)
would not know the data is corrupt.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Some hardware, such as the enhanced local bus controller used on some
mpc83xx chips, does ecc transparently when reading and writing data, rather
than providing a generic calculate/correct mechanism that can be exported to
the nand subsystem.
The subsystem should not BUG() when calculate, correct, or hwctl are
missing, if the methods that call them have been overridden.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Driver for the device bus NAND controller in the Marvell Orion family
of ARM SoCs.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Plumbing for NAND connected via localbus on PA Semi PWRficient-based
boards.
From: Egor Martovetsky <egor@pasemi.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ensure the nFCE line is de-asserted over suspend and
then re-initialised when the system resumes. This is
to ensure that the NAND is kept in lowest power mode
over suspend (power settings are only specified for
nFCE inactive) as well as fixing the Simtec Osiris
which relies on nFCE being inactive.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Magic numerical values are just bad style. Particularly so when
undocumented.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Treat any negative return value from a NAND driver's correct() function
as a failure, rather than just -1.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
NAND of > 32MiB in size use 4 bytes in address cycle, not 3.
Reported-by: bhsong <bhsong@augustatek.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add read_buf/write_buf for s3c2440, which can read/write 32 bits at a
time rather than just 8. In my testing on an s3c2440a running at 400 MHz
with a 100 MHz HCLK, read performance improves by 36% (from 5.19 MB/s
to 7.07 MB/s).
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the driver for latest Blackfin on-chip nand flash controller
- use nand_chip and mtd_info common nand driver interface
- provide both PIO and dma operation
- compiled with ezkit bf548 configuration
- use hardware 1-bit ECC
- tested with YAFFS2 and can mount YAFFS2 filesystem as rootfs
ChangeLog from try#1
- use hweight32() instead of count_bits()
- replace bf54x with bf5xx and BF54X with BF5XX
- compare against plat->page_size in 2 cases when enable hardware ECC
ChangeLog from try#2
- passed nand_test suites
- use cpu_relax() instead of busy wait loop
- some coding style issue pointed out by Andrew
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/alauda.c: In function 'alauda_bounce_read':
drivers/mtd/nand/alauda.c:412: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When the erase callback performs some other action on the flash, it's
highly likely to deadlock unless we actually release the chip lock
before calling it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Originally from Marcelo; modified to put the original timing registers
back instead of 0xFFFFFFFF.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
It was only the very early prototypes which made the mistake of using
the same device ident for all three functions on the device -- don't
bother trying to express that in the PCI match table, since the tools
don't cope. We can check in the probe routine instead, just in case.
Also remember to terminate the table.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixup the includes which have been moved around
when changing the s3c24xx arch support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make nandsim use GFP_NOFS when allocating memory, because it might
be used by a file-system (e.g. UBIFS2) which means, if we are short
of memory, we may deadlock. Indee, UBIFS is holding a lock, writes
to the media, reaches this place in NANDsim, kmalloc does not find
the requested amount of RAM, calls memory shrinker, which decides
to writeback inodes, calls FS, and it deadlocks on the lock which
is already being held. Below is the UBIFS backtrace which
demonstrates that:
[<c03717dc>] __mutex_lock_slowpath+0xc8/0x2e6
[<c0371a16>] mutex_lock+0x1c/0x1f
[<f8b9d076>] reserve_space+0x3d/0xa9 [ubifs]
[<f8b9d1bd>] make_one_reservation+0x2b/0x86 [ubifs]
[<f8b9d3fc>] ubifs_jrn_write_block+0xda/0x12f [ubifs]
[<f8b9ff3a>] ubifs_writepage+0x11d/0x1ec [ubifs]
[<c015d6ab>] shrink_inactive_list+0x7fa/0x969
[<c015d8c8>] shrink_zone+0xae/0x10c
[<c015e3b4>] try_to_free_pages+0x159/0x251
[<c015980a>] __alloc_pages+0x125/0x2f0
[<c016ff6a>] cache_alloc_refill+0x380/0x6ba
[<c01703f3>] __kmalloc+0x14f/0x157
[<f885722a>] do_state_action+0xab7/0xc74 [nandsim]
[<f885760c>] switch_state+0x225/0x402 [nandsim]
[<f8857e7e>] ns_hwcontrol+0x3e2/0x620 [nandsim]
[<f8862f53>] nand_command+0x2e/0x1a5 [nand]
[<f8861ad8>] nand_write_page+0x4a/0x9a [nand]
[<f88617b4>] nand_do_write_ops+0x1cf/0x343 [nand]
[<f8861a70>] nand_write+0x88/0xa6 [nand]
[<f8850b0e>] part_write+0x72/0x8b [mtd]
[<f88e19c5>] ubi_io_write+0x189/0x29c [ubi]
[<f88dfb98>] ubi_eba_write_leb+0xb6/0x699 [ubi]
[<f88def93>] ubi_leb_write+0xe4/0xe9 [ubi]
[<f8ba3b82>] ubifs_wbuf_write_nolock+0x333/0x4c9 [ubifs]
[<f8b9d28c>] write_node+0x74/0x8e [ubifs]
[<f8b9d422>] ubifs_jrn_write_block+0x100/0x12f [ubifs]
[<f8b9ff3a>] ubifs_writepage+0x11d/0x1ec [ubifs]
[<c0159e5b>] __writepage+0xb/0x26
[<c015a318>] write_cache_pages+0x203/0x2d9
[<c015a411>] generic_writepages+0x23/0x2d
[<c015a452>] do_writepages+0x37/0x39
[<c018e24a>] __writeback_single_inode+0x96/0x399
[<c018e903>] sync_sb_inodes+0x1a3/0x274
[<c018ebf3>] writeback_inodes+0xa6/0xd8
[<c015a9dd>] background_writeout+0x86/0x9e
[<c015ae9c>] pdflush+0xfb/0x1b6
[<c01387d7>] kthread+0x37/0x59
[<c0104dc3>] kernel_thread_helper+0x7/0x14
The deadlock is funny because it starts in pdflush/writeback,
and comes back to writeback, then deadlocks. It seems we should look
carefully for other places in UBI and MTD and use GFP_NOFS instead
of GFP_KERNEL.
Caught-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Unlike most stuff on the market the chip inside these two allows raw
flash access and doesn't implement and FTL, leaving that functionality
to the device driver.
Raw flash access in a cheap USB cardreader! An MTD test device one can
attach to a PC! What a deal!
The command set of the chip is not documented, so information was
obtained from the existing mass-storage driver
(drivers/usb/storage/alauda.c), its documentation
(http://alauda.sourceforge.net/wikka.php?wakka=BulkCommandReference),
additional reverse engineering and comparison with a vendor driver for a
related chip
(http://www.ratocsystems.com/english/download/driver/linux/sma03u.html).
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
These drivers are specific to 4xx support in arch/ppc at the moment. Make
sure they don't get built on arch/powerpc.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The nand_base.c driver implicitly casts the uint32_t
eccpos array to 'int *', which is not only not guaranteed
to be the same sign as the source, but is not guaranteed
to be the same size.
Fix by changing nand_base.c to use uint32_t
referencing the eccpos fields.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below fixes nand driver for AT91 boards which do not have NAND
R/B signal connected to gpio (rdy_pin is not connected).
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we mark block bad we have to get chip because this involves
writing to the page's OOB. We hit this bug in UBI - we observed
random obscure crashes when it marks block bad from the background
thread and there is some parallel task which utilizes flash.
This patch also adds a TODO note about BBT table protection which
it seems does not exist.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch ensures that the current code (kernel 2.6.22) uses the bits
like the code prior to the refactoring. The variable "bits" is employed
in a useful way now.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
replace with working link from nand Kconfig help text
fixes bugzilla 7815
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we mark block bad we have to get chip because this involves
writing to the page's OOB. We hit this bug in UBI - we observed
random obscure crashes when it marks block bad from the background
thread and there is some parallel task which utilizes flash.
This patch also adds a TODO note about BBT table protection which
it seems does not exist.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch ensures that the current code (kernel 2.6.22) uses the bits
like the code prior to the refactoring. The variable "bits" is employed
in a useful way now.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch cleans up duplicate includes in
drivers/mtd/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds the manufacturer ID for AMD flash.
Signed-off-by: Steven J. Hill <sjhill1@rockwellcollins.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch has removed Ocelot G support from MTD.
Ocelot G support has already removed since May 2007.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The price might drop to $100 in a few years.
But currently, a more reasonable name might be "$175 laptop".
Let's simply call it "OLPC laptop" without any price tag.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds 405 platform support to the 440 NDFC driver. The new
AMCC 405EZ PPC is equipped with the same NDFC core as the 440EP(x)
and other will follow soon.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The nand_base.c driver implicitly casts the uint32_t
eccpos array to 'int *', which is not only not guaranteed
to be the same sign as the source, but is not guaranteed
to be the same size.
Fix by changing nand_base.c to use uint32_t
referencing the eccpos fields.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below fixes nand driver for AT91 boards which do not have NAND
R/B signal connected to gpio (rdy_pin is not connected).
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix various bits of obviously-busted code which we're not happening to
compile, due to ifdefs.
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jan Kara <jack@ucw.cz>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have made a tool to parse the kernel that does not pre-process the
source. That means that my parser tries to parse all the code, including
code in the #else branch or code that is not often compiled because the
driver is not very used (or not used at all). So, my parser sometimes
reports parse error not originally detected by gcc. Here is my (first)
patch.
[akpm@linux-foundation.org: fix amd8111e.c]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (21 commits)
[MTD] [CHIPS] Remove MTD_OBSOLETE_CHIPS (jedec, amd_flash, sharp)
[MTD] Delete allegedly obsolete "bank_size" field of mtd_info.
[MTD] Remove unnecessary user space check from mtd.h.
[MTD] [MAPS] Remove flash maps for no longer supported 405LP boards
[MTD] [MAPS] Fix missing printk() parameter in physmap_of.c MTD driver
[MTD] [NAND] platform NAND driver: add driver
[MTD] [NAND] platform NAND driver: update header
[JFFS2] Simplify and clean up jffs2_add_tn_to_tree() some more.
[JFFS2] Remove another bogus optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remove broken insert_point optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remember to calculate overlap on nodes which replace older nodes
[JFFS2] Don't advance c->wbuf_ofs to next eraseblock after wbuf flush
[MTD] [NAND] at91_nand.c: CMDLINE_PARTS support
[MTD] [NAND] Tidy up handling of page number in nand_block_bad()
[MTD] block2mtd_paramline[] mustn't be __initdata
[MTD] [NAND] Support multiple chips in CAFÉ driver
[MTD] [NAND] Rename cafe.c to cafe_nand.c and remove the multi-obj magic
[MTD] [NAND] Use rslib for CAFÉ ECC
[RSLIB] Support non-canonical GF representations
[JFFS2] Remove dead file histo_mips.h
...
This patch adds support for generic platform NAND driver.
Updated after tglx's review/discussion in IRC #mtd channel.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch allows you to specify at91_nand partitions on the
kernel command line using the mtdparts variable, if
CONFIG_MTD_CMDLINE_PARTS is set.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Further to the previous patch fixing the calculation of page number,
both branches are using the same result. Clean up the function
accordingly, calculating it (and also masking with pagemask) only in one
place.
Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The CAFÉ can handle two chip on separate chipselect lines. Hook up the
undocumented chipselect bits in the driver and probe both.
In the case of OLPC, it's not actually two separate devices -- it's a
single '1GiB' package with two 512MiB dies internally. So clear the
NAND_BBT_PERCHIP flag to treat it as a single chip for BBT purposes, and
make life easier for the firmware.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch provides MTD support for NAND flash devices on CM-x270 modules.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In case that there is no memory based bad block table available the
function nand_block_checkbad() in drivers/mtd/nand/nand_base.c will call
nand_block_bad() directly. When parameter 'getchip' is set to zero,
nand_block_bad() will not right shift the offset to calculate the
correct page number.
Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A new module parameter has been added called 'overridesize',
which overrides the size that would be determined by the
ID bytes. 'overridesize' is specified in erase blocks and
as the exponent of a power of two e.g. 5 means a size of
32 erase blocks.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A new module parameter 'rptwear' specifies how many erases between
reporting wear information. Zero means never.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
New module parameters have been added to nandsim to
simulate:
bitflips random bit flips
badblocks blocks that are initially marked bad
weakblocks blocks that fail to erase after a
small number of erase cycles
weakpages pages that fail to write after a
small number of successful writes
gravepages pages that fail to read after a
small number of successful reads
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Enhance nandsim to be able to create more than 1 partition.
A new module parameter 'parts' may be used to specify partition
sizes.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is a slight bug in nand_default_block_markbad, where the offset is
cast to an integer, prior to being shifted. This means that on large
offsets, it is incorrectly doing a signed shift & losing bits. Fixed
this by doing the cast after the shift (as is done elsewhere in the code).
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use the functions in the ecc structure instead of the default ones,
so the override by the board driver is effective also for software ecc
code paths.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Replace the apparently misspelled preprocessor variable
"MTD_NAND_DISKONCHIP_BBTWRITE" with the correct form
"CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
During the MTD rework the oobavail parameter of mtd_info structure has become
private. This is not quite correct in terms of integrity and logic. If we have
means to write to OOB area, then we'd like to know upfront how many bytes out
of OOB are spare per page to be able to adapt to specific cases.
The patch inlined adds the public oobavail parameter.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Noticed while building a s3c2410 kernel :
drivers/mtd/nand/s3c2410.c: In function 's3c2440_nand_calculate_ecc':
drivers/mtd/nand/s3c2410.c:476: warning: format '%06x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
This patch fixes it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2412 use differents registers than s3c2440 for hw ecc handling.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.fr>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/cafe.c: In function 'cafe_nand_cmdfunc':
drivers/mtd/nand/cafe.c:269: warning: 'irqs' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal. Fixup the remaining users in -mm.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a nand flash driver for the eXcite series of intelligent
cameras manufactured by Basler Vision Technologies AG.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for correcting errors detected by the
hardware ECC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Remove unused and broken mtd->ecctype and mtd->eccsize fields
from struct mtd_info. Do not remove them from userspace API
data structures (don't want to breake userspace) but mark them
as obsolete by a comment. Any userspace program which uses them
should be half-broken anyway, so this is more about saving
data structure size.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
err_pos_lut[4096] of an array with 4096 elements is a bug.
Spotted by the Coverity checker.
While I was at it, I also converted it to ARRAY_SIZE().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add checks to ensure that out-of-band reads and writes are
not attempted with an invalid offset or length. Specifically,
the offset must be less than the size of oob for a page
and the length must not go beyond the size of the device.
Additionally the checks must adjust for auto-placement
(MTD_OOB_AUTO) of oob data.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The precise timings are board-specific (or NAND chip specific) and don't
belong here. If they're set already, then use what we find there.
Otherwise, revert to the most conservative default values (and whinge).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for 16-bit NAND bus-width for the AT91 NAND driver.
The 16-bit NAND is found on the Atmel AT91SAM9260-EK and AT91SAM9261-EK
boards.
Orignal Patch from Patrice Vilchez
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Number of address bytes for 64-128 MiB NANDs is 4, not 5.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
