a6c268d033
The debugfs interface brought a copy of the test case parameters. This makes different set of values under /sys/module/dmatest/parameters/ and /sys/kernel/debug/dmatest/. The user might be confused by the divergence of values. The proposed solution in this patch is to make module parameters writable and remove them from the debugfs. Though we're still using debugfs to control test runner and getting results. Documentation part is updated accordingly. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Suggested-by: Dan Williams <djbw@fb.com> Signed-off-by: Dan Williams <djbw@fb.com>
83 lines
2.9 KiB
Plaintext
83 lines
2.9 KiB
Plaintext
DMA Test Guide
|
|
==============
|
|
|
|
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
|
|
This small document introduces how to test DMA drivers using dmatest module.
|
|
|
|
Part 1 - How to build the test module
|
|
|
|
The menuconfig contains an option that could be found by following path:
|
|
Device Drivers -> DMA Engine support -> DMA Test client
|
|
|
|
In the configuration file the option called CONFIG_DMATEST. The dmatest could
|
|
be built as module or inside kernel. Let's consider those cases.
|
|
|
|
Part 2 - When dmatest is built as a module...
|
|
|
|
After mounting debugfs and loading the module, the /sys/kernel/debug/dmatest
|
|
folder with nodes will be created. There are two important files located. First
|
|
is the 'run' node that controls run and stop phases of the test, and the second
|
|
one, 'results', is used to get the test case results.
|
|
|
|
Note that in this case test will not run on load automatically.
|
|
|
|
Example of usage:
|
|
% echo dma0chan0 > /sys/module/dmatest/parameters/channel
|
|
% echo 2000 > /sys/module/dmatest/parameters/timeout
|
|
% echo 1 > /sys/module/dmatest/parameters/iterations
|
|
% echo 1 > /sys/kernel/debug/dmatest/run
|
|
|
|
Hint: available channel list could be extracted by running the following
|
|
command:
|
|
% ls -1 /sys/class/dma/
|
|
|
|
After a while you will start to get messages about current status or error like
|
|
in the original code.
|
|
|
|
Note that running a new test will not stop any in progress test.
|
|
|
|
The following command should return actual state of the test.
|
|
% cat /sys/kernel/debug/dmatest/run
|
|
|
|
To wait for test done the user may perform a busy loop that checks the state.
|
|
|
|
% while [ $(cat /sys/kernel/debug/dmatest/run) = "Y" ]
|
|
> do
|
|
> echo -n "."
|
|
> sleep 1
|
|
> done
|
|
> echo
|
|
|
|
Part 3 - When built-in in the kernel...
|
|
|
|
The module parameters that is supplied to the kernel command line will be used
|
|
for the first performed test. After user gets a control, the test could be
|
|
re-run with the same or different parameters. For the details see the above
|
|
section "Part 2 - When dmatest is built as a module..."
|
|
|
|
In both cases the module parameters are used as the actual values for the test
|
|
case. You always could check them at run-time by running
|
|
% grep -H . /sys/module/dmatest/parameters/*
|
|
|
|
Part 4 - Gathering the test results
|
|
|
|
The module provides a storage for the test results in the memory. The gathered
|
|
data could be used after test is done.
|
|
|
|
The special file 'results' in the debugfs represents gathered data of the in
|
|
progress test. The messages collected are printed to the kernel log as well.
|
|
|
|
Example of output:
|
|
% cat /sys/kernel/debug/dmatest/results
|
|
dma0chan0-copy0: #1: No errors with src_off=0x7bf dst_off=0x8ad len=0x3fea (0)
|
|
|
|
The message format is unified across the different types of errors. A number in
|
|
the parens represents additional information, e.g. error code, error counter,
|
|
or status.
|
|
|
|
Comparison between buffers is stored to the dedicated structure.
|
|
|
|
Note that the verify result is now accessible only via file 'results' in the
|
|
debugfs.
|