get common buffers() should block operation until valid buffer
is avaliable.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Assign using the new gpio structures, i/o for exist HPG
targets, without removing the old implementation.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card modules is the component which handles various targets,
so the IDs table should reside within it.
[mchehab@redhat.com: add missing smsendian.h include at smscoreapi.c]
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the infra-red to the makefile and declare
the assignment in the cards components.
[mchehab@redhat.com: Fixed a few trivial merge conflicts]
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add gpio look-up table for various requirements, any
target may select any gpio and assign it to a function
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the DVB-API v3 headers' include list from the core component
to the smsdvb (DVB adapter) which is the only one that uses them.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replace the old method of pulling the device status by
sending "get_statistics" request, to push mode. This make status update
much faster, and reduce various operation time (UHF scan now takes 15s
instead of 2m). In order to make the change the following modification
have been applied:
1) core header - update statistics headers.
2) dvb adapter - omit the statistics request, add handling of
status indications.
3) core 'onresponse' - re-route messages addressed to other adapter
to the dvb adapter.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for Siano protocol messages
with big endian systems.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a problem were protocol buffers
have been lost during USB disconnect events.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for byte ordering and big endianity
handling for the USB interface driver
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch updates the license of the USB interface driver
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove redundant complete instruction from smsdvb, in the
past this was used by the statistics state machine, but
no longer.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Siano: smsdvb - Fix license to match all other Siano's files
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Re-order the include files list
Re-order the include files list, put the DVB-API v3 within its
own section, within a define container.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modify the file license to match all other Siano's files
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code that modify the content of Siano's protocol
messages when running with big-endian target.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add support for IR (infra-red)
remote controllers.
Further commits are needed in order to enable the
activation of the IR components.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some more indentation for the smscoreapi.h
There are no implementation changes in this patch.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
smscoreapi - move the main core structure declaration
to the header, in order to enable other components
(such as IR) to use it.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove two redundant lines, based on Klimov Alexey code review.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx88-dsp: fixing 64bit math on 32bit kernels
Some gcc versions report the missing of __divdi3
[mchehab.redhat.com: CodingStyle fixes]
Signed-off-by: Miroslav Sustek <sustmidown@centrum.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes cx88_set_stereo to avoid resetting all of the audio
registers on stereo/mono change if the audio standard is A2, and set
only the AUD_CTL register. The benefit of this method is that it
eliminates the annoying clicking noise on setting the audio mode to
stereo or mono.
The driver had used the same method 1.5 years ago (and for FM radio it
still does), but a pretty big cleanup commit changed it to the
"complete audio reset" method, although the reason for this move was
not clear. (If somebody knows why it was necessary, please let me
know!)
The original commit: http://linuxtv.org/hg/v4l-dvb/rev/ffe313541d7d
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sole purpose of the audio thread is to detect if stereo transmission is
available, and if it is, then switch to stereo mode (and switch back, if it's
no longer available). This manual autodetection is useful for some audio
standards (e.g. A2) where cx88_get_stereo CAN detect stereo sound, but the
cx2388x chip CANNOT auto-detect stereo sound.
However, for other audio standards, the cx2388x chip CAN auto-detect the stereo
sound, so the manual autodetection in the audio thread is not needed. In fact,
it can cause serious problems because for some of these audio standards,
cx88_get_stereo CANNOT detect the presence of stereo sound. Besides that, if
the hardware automatically detects stereo/mono sound, you cannot set
core->audiomode_current to the real current audio mode on channel change.
With this patch, the manual autodetection is only used if audiomode_current is
known after a channel change (because of the initial mono mode), and
hardware-based stereo autodetecion is not applicable for the current audio
standard.
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch implements reliable stereo and sap detection for the A2 sound
standard. This is achieved by processing the samples of the audio RDS fifo of
the cx2388x chip. A2M, EIAJ and BTSC stereo/sap detection is also possible with
this new approach, but it's not implemented yet. Stereo detection when alsa
handles the sound also does not work yet.
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides SDIO interface driver for SMS (Siano Mobile
Silicon) based devices. The patch includes SMS high level SDIO driver
and requires patching the kernel SDIO stack, those stack patches had
been provided previously.
I would like to thank Pierre Ossman, MMC maintainer, who wrote this
driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
sdio: add cards id for sms (Siano Mobile Silicon) MDTV receivers
Add SDIO vendor ID, and multiple device IDs for
various SMS-based MDTV SDIO adapters.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fact that we now explicitly set fepriv->exit = 1 when the thread is
shutting down exposed an edge case where it was not being reset back to zero
once the thread went away in some cases. This resulted in failures in cases
where the frontend was closed, and then opened O_RDONLY, since in that case
the thread is not being restarted but it was checking the fepriv->exit flag.
Thanks to Thierry Lelegard, who and encountered and debugged a large portion
of the issue in the same twelve hours that I did (as well as testing my patch).
Cc: Thierry Lelegard <thierry.lelegard@tv-numeric.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for big endien target hosts, which
use USB interface.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A race condition was detected in the case that putting the tuner to sleep takes
an unusually long period of time, combined with applications that quickly
close/open the dvb frontend.
The kaffeine channel scanner closes and reopens the dvb frontend between each
tuning attempt. If it takes an unusually longer period of time to put the
tuner to sleep (for example, the Pinnacle 801e takes 660 ms), the dvb_frontend
thread will still be in a running state (and hence fepriv->thread is still set)
but the fepriv->exit field will still be zero. As a result, if a
dvb_frontend_start() call arrives while the frontend thread is in the process
of terminating, the call will return 0 without actually starting a new thread.
This results in the tuning request being dropped.
To address this, mark fepriv->exit as soon as we know the thread is going to
be terminated, so that dvb_frontend_start() knows to start a new instance.
Problem encountered with Kaffeine 0.8.7 doing ATSC scanning against the
Pinnacle 801e tuner, in conjunction with new code to power down the xc5000
when not in use.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A power management fix to properly put the xc5000 into low power mode
revealed a race condition where hald could detect the creation of the device
file and connect to the device while the initial device configuration is
still in progress.
Lock the core structure so that video_release cannot be called and put the
tuner to sleep in the middle of the initial call to cx88_set_tvnorm() in
cx8800_initdev()
Thanks to Michael Krufky for discovering the issue and providing an
environment to test in.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Error count in read pipe completion corrected.
URB not resubmitted if shutting down.
URB not freed in completion routine if new urb_submit_fails.
(URB is freed on shutdown).
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for no return value check of uvc_ctrl_set() which calls
mutex_lock_interruptible().
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
lgs8gxx: lgs8913 fake signal strength option default on. Original
calculation is too slow.
Signed-off-by: David T.L. Wong <davidtlwong <at> gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having fixed the sprintfs I decided a quick clean wouldn't do any harm so
it was actually easy to read in future.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add 1461:f736 to the list of identifiers corresponding to the
SAA7134_BOARD_AVERMEDIA_M103 board. This patch adds support for
a variant of the AVerMedia M103 MiniPCI DVB-T Hybrid card.
Signed-off-by: Barry Kitson <b.kitson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vfree() does it's own NULL checking, no need for explicit check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code creates a sysfs device path where the video4linux
device is child of the usb device itself instead of the interface it
belongs to. That is evil and confuses udev.
This patch does basically the same thing as Kay's similar patch for the
ov511 driver:
at git commit ce96d0a44a
Signed-off-by: Lennart Poettering <mzxreary@0pointer.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add missing __devexit_p() to several drivers. Also add a few missing
__init, __devinit and __exit markers. These errors could result in
build failures depending on the kernel configuration.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
add poiter check for videobuf_queue_core_init().
any guys who write a v4l driver, pass a NULL pointer or a non-inintial
pointer to the first parameter such as videobuf_queue_sg_init() , it
would be crashed.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
when re-open or re-start (video_streamon), the q->curr would not be NULL in saa7134_buffer_queue(),
and all the qbuf will add to q->queue list,no one to do activate to start DMA,and then no interrupt
would happened,so it will be block.
In VIDEOBUF_NEEDS_INIT state, initialize the curr pointer to be NULL in the buffer_prepare().
Signed-off-by: Figo.zhang <figo.zhang@kolorific.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
