The cx2388x family has a color killer. This patch implements the
V4L2_CID_COLOR_KILLER control for the cx2388x family. By default the
color killer is disabled, as in previous versions of the driver.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define a pre-defined control ID for color killer functionality.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An enabled chroma AGC will not degrade picture quality if enabled on a
color PAL or NTSC signal with nominal signal levels. It will give a
significant color reproduction improvement if the chroma signals
diverge from nominal levels. Therefore enable chroma AGC by default
for PAL and NTSC standards.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx2388x family has support for chroma AGC. This patch implements a
the V4L2_CID_CHROMA_AGC control for the cx2388x family. By default
chroma AGC is disabled, as in previous versions of the driver.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define a pre-defined control ID for chroma automatic gain control.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the IR worker is not stopped before the removal of the cx88xx module,
an OOPS may occur, because the worker function cx88_ir_work gets called.
So stop the ir worker.
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This board has a s5h1409 demod, plus a xc30x8 tuner (probably, xc3018).
This patch adds proper support for radio, video, s-video, composite and ATSC.
However, support for radio and video depends on having s5h1409 i2c gate open,
otherwise, xc30x8 chip won't be visible.
For a better support, some rework is needed on cx88 driver, to allow adding
xc30x8 to i2c bus without sending i2c 0 byte reading to 0xc2 address.
Thanks to Vanessa Ezekowitz <vanessaezekowitz@gmail.com> for helping to figure
out the proper parameters for s5h1409 and the GPIO pins used by each
configuration.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix use of a non-int (size_t) being passed in a printf width field.
This benign issue has apparently been around for a long time, but went
undetected until now.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update Kconfig for the hybrid devices recently converted
to use tuner-simple rather than dvb-pll.
dvb-bt8xx no longer uses dvb-pll at all, so remove all
references to dvb-pll within that driver.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following build error:
In file included from dvb-bt8xx.c:35:
dvb-bt8xx.h:42:26: error: tuner-simple.h: No such file or directory
dvb-bt8xx.c: In function 'frontend_init':
dvb-bt8xx.c:612: error: 'simple_tuner_attach' undeclared (first use in this function)
dvb-bt8xx.c:612: error: (Each undeclared identifier is reported only once
dvb-bt8xx.c:612: error: for each function it appears in.)
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of '__a'
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:612: warning: cast from pointer to integer of different size
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:612: warning: cast from pointer to integer of different size
dvb-bt8xx.c:612: error: called object '__a' is not a function
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of '__a'
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:696: warning: cast from pointer to integer of different size
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:696: warning: cast from pointer to integer of different size
dvb-bt8xx.c:696: error: called object '__a' is not a function
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are a number of different firmware versions and variants, shipped
together with boards.
This patch adds an extra parameter to the tuner-xc2028 to allow specifying for
an specific firmware name to be loaded. This helps to test for a firmware that
better fits some board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Force the main pll charge pump or cal pll charge pump to source current
to the main pll loop filter or cal pll loop filter, respectively.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Set rfagc to high speed mode before setting the pll.
Set rfagc to normal speed mode at the end of the function.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
allow device-specific configuration of rf agc rf top and if top
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The internal calibration signal must be set on the cal pll.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Both the tda18271 c1 and c2 parts only need EP3 through MD3 to be written for
the image rejection calibration's low band initialization.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ability to select RF input was a supported feature only available on
Philips TUV1236d and Philips FCV1236d.
This feature, along with support for the tuners that used it,
was moved into the tuner-simple module.
This can now be removed from dvb-pll.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
remove #if 0'd support for:
Philips TUV1236D
Philips TD1316
Philips FMD1216ME
LG TDVS-H06xF
Philips FCV1236D
Thomson FE6600
Microtune 4042 FI5
Thomson dtt761x
Support for these tuners has been moved into the 'tuner-simple' module.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb and saa7134-dvb to use tuner-simple instead of dvb-pll
for Philips TUV1236D
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert saa7134-dvb to use tuner-simple instead of dvb-pll for Philips TD1316
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cxusb, cx88-dvb and saa7134-dvb to use tuner-simple instead of
dvb-pll for Philips FMD1216ME
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb, dvb-bt8xx, b2c2-flexcop, cxusb and cx23885 to use
tuner-simple instead of dvb-pll for LG TDVS-H06xF
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert dvb-bt8xx to use tuner-simple instead of dvb-pll for Philips FCV1236D
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb to use tuner-simple instead of dvb-pll for Thomson FE6600
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb to use tuner-simple instead of dvb-pll for Microtune 4042 FI5
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb to use tuner-simple instead of dvb-pll for Thomson DTT 761X
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add module options to tuner-simple, called "atv_input" and "dtv_input"
to specify which rf input to use on devices with multiple rf inputs.
If the module option is not specified, then the driver will autoselect
the rf input, as per previous behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes several kernel oops, when unplugging device while it is in
use:
Basically the patch delays freeing of the internal variables in
si470x_usb_driver_disconnect, until the the last user closed the device in
si470x_fops_release. This was implemented a while ago with the help of Oliver
Neukum.
I tested the patch five times (unplugging while in use) without oops coming
from the radio-si470x driver anymore. A remaining oops was coming from the
usbaudio driver, but this is someone else task. Hopefully this fixed all
unplugging issues.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The video_dev parameter, on tuner-xc2028 were used to pass i2c private data to
tuner_callback. Since the driver already have a pointer to i2c_adap->algo_data,
uses this instead.
This parameter were used also as a magic number to idenfity if two drivers are
trying to register the same xc3028 tuner. This occurs with boards with DVB
support, where both DVB and V4L drivers will share the same tuner.
Instead of using the algo_data as a private number, after this patch, the
driver will use i2c_adap->dev, with seems more consistent.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds a consistency check to avoid OOPS, if tuner_callback priv argument is
NULL. Also, simplifies callback codes on cx88.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ISL6405 LNB supply is used on several Creatix / Medion cards. But only
the MD8800 needs its second section. So don't start it unless it is needed.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
