There's a dependency missing.
$ make localyesconfig
HOSTCC scripts/basic/fixdep
HOSTCC scripts/basic/docproc
HOSTCC scripts/basic/hash
using config: '/boot/config-2.6.27.25-78.2.56.fc9.x86_64'
/bin/sh: line 8: scripts/kconfig/conf: No such file or directory
make[1]: *** [localyesconfig] Error 127
make: *** [localyesconfig] Error 2
Thus the script failed to run. But the sed command that converts the '=m'
to '=y' still ran. This gives us a distro config with all modules
converted to built in!
The missing dependency was for conf for localyesconfig. This
dependency was already set for localmodconfig.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If one were to run localmodconfig or localyesconfig without having
a .config already in the file, then the end of the process would give
a warning when it tries to move the old .config to .config.old.
This patch adds a test to check if .config exists and avoid the moves
if it does not.
[ Impact: remove warning after make localmodconfig ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As Andi Kleen pointed out, most people would expect that the local .config
file to be based for a streamline config. This patch changes the order
of searching for a config file to consider the .config in the local
directory first.
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Many distros put their config in /boot/config-`uname -r`, add a check
for that right after /proc/config.gz
Reported-by: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Due to cut and paste error IKCONFIG was both set and cleared.
It was suppose to be IKCONFIG_PROC to be cleared.
Also cleaned up if nesting.
Reported-by: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Instead of using the .config in the local directory. This patch
changes streamline_config.pl to search various locations for a config.
Here's the list and order of search:
/proc/config.gz
/boot/vmlinuz-`uname -r`
vmlinux # local to the directory
/lib/modules/`uname -r`/kernel/kernel/configs.ko
kernel/configs.ko
kernel/configs.o
.config
Once it finds a file that contains a config (it checks if the binary
objects have configs first) it then uses it to create the .config
with minimum modules needed.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If CONFIG_IKCONFIG is set but CONFIG_IKCONFIG_PROC is not, then
gcc will optimize the config.gz out, because nobody uses it.
This patch adds "__used" to the config.gz data to keep it around so that
code like extract-ikconfig can still find it.
[ Impact: allow extract-ikconfig to find config.gz ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
It would be nice to use extract-ikconfig to find the congfig.gz
in either vmlinux (not vmlinuz) or configs.ko.
This patch changes the script to also be able to read ELF files directly.
[ Impact: find config.gz in vmlinux and configs.ko ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Ingo Molnar suggested that the streamline_config.pl should enable
CONFIG_IKCONFIG to keep the current config in the kernel.
Then we can use scripts/extract-ikconfig to find the current
modules.
This patch changes streamline_config.pl to check if CONFIG_IKCONFIG
is not set, and if it is not, it enables it to be a module.
[ Impact: make current config options easier to find ]
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The streamline_config.pl finds all the configs that are needed to
compile the currently loaded modules. After it creates the .config
file, it tests to make sure all the configs that are needed were
set.
It only looks at the configs that are modules, it does not look
at the builtin configs. This causes unnecessary warnings about modules
not being covered.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If a config does not have a prompt, it must be selected.
streamline_config.pl keeps track of all configs that select other configs.
If a config that does not have a prompt needs to be set to enable a
current module, it will include all configs that select it.
Note, streamline_config.pl does not enable modules that are not already
enabled. It only keeps enabled those that were enabled and might be
needed to compile the current modules.
The code to find the selects of a config is after the code that
adds the depends. But if a config needed selects but had no dependencies,
it would not be set. Because the code would stop before getting to
the select.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This adds the option localyesconfig to make. This is similar to
localmodconfig, but after it removes unnecessary modules it runs
sed -i s/=m/=y/
on the .config file. It then runs "make silentoldconfig" to fix any
wholes that were created by the conversion of modules to core.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Running the streamline_config.pl script manually can still be confusing
for some users. This patch adds the localmodconfig option. This will
automatically run streamline_config.pl on the current .config and
then run "make silentoldconfig" to fix any wholes that might have been
created.
$ make localmodconfig
This will remove any module configurations in .config that are not needed
to compile the modules that are loaded.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
streamline_config.pl is a very powerful tool. For those that install
a kernel to a new box using the config file from the distribution know that
it can take forever to compile the kernel.
Making a custom config file that will still boot your box, but bring
down the compile time of the kernel can be quit painful, and to ask
someone that reported a bug to do this can be a large burdon since that
person may not even know how to build a kernel.
This script will perform "lsmod" to find all the modules loaded on the
current running system. It will read all the Makefiles to map which
CONFIG enables a module. It will read the Kconfig files to find the
dependencies and selects that may be needed to support a CONFIG.
Finally, it reads the .config file and removes any module "=m" that is
not needed to enable the currently loaded modules. The output goes to
standard out.
Here's a way to run the script. From the Linux directory that holds
a distribution .config.
$ scripts/kconfig/streamline_config.pl arch/x86/Kconfig > config-sl
$ mv .config config-save
$ mv config-sl .config
$ make oldconfig
Now you have a .config that will still build all your modules, but also
take much less time to build the kernel.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If node_load[] is cleared everytime build_zonelists() is
called,node_load[] will have no help to find the next node that should
appear in the given node's fallback list.
Because of the bug, zonelist's node_order is not calculated as expected.
This bug affects on big machine, which has asynmetric node distance.
[synmetric NUMA's node distance]
0 1 2
0 10 12 12
1 12 10 12
2 12 12 10
[asynmetric NUMA's node distance]
0 1 2
0 10 12 20
1 12 10 14
2 20 14 10
This (my bug) is very old but no one has reported this for a long time.
Maybe because the number of asynmetric NUMA is very small and they use
cpuset for customizing node memory allocation fallback.
[akpm@linux-foundation.org: fix CONFIG_NUMA=n build]
Signed-off-by: Bo Liu <bo-liu@hotmail.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the POSIX (1003.1-2008), the file descriptor shall have been
opened with read permission, regardless of the protection options specified to
mmap(). The ltp test cases mmap06/07 need this.
Signed-off-by: Graff Yang <graff.yang@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the changes to the bitbang driver, there is the possibility we will
be called with either the speed_hz or bpw values zero. We take these to
mean that the default values (8 bits per word, or maximum bus speed).
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the clock rate calculation may round as pleased, which means
that it is possible that we will round down and end up with a faster clock
rate than intended.
Change the calculation to use DIV_ROUND_UP() to ensure that we end up with
a clock rate either the same as or lower than the user requested one.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a number of individual MMC drivers listed in MAINTAINERS. I
didn't modify those records. Perhaps I should have.
Cc: <linux-mmc@vger.kernel.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Pavel Pisa <ppisa@pikron.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Sascha Sommer <saschasommer@freenet.de>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit 2ff05b2b (oom: move oom_adj value) moveed the oom_adj value to
the mm_struct. It was a very good first step for sanitize OOM.
However Paul Menage reported the commit makes regression to his job
scheduler. Current OOM logic can kill OOM_DISABLED process.
Why? His program has the code of similar to the following.
...
set_oom_adj(OOM_DISABLE); /* The job scheduler never killed by oom */
...
if (vfork() == 0) {
set_oom_adj(0); /* Invoked child can be killed */
execve("foo-bar-cmd");
}
....
vfork() parent and child are shared the same mm_struct. then above
set_oom_adj(0) doesn't only change oom_adj for vfork() child, it's also
change oom_adj for vfork() parent. Then, vfork() parent (job scheduler)
lost OOM immune and it was killed.
Actually, fork-setting-exec idiom is very frequently used in userland program.
We must not break this assumption.
Then, this patch revert commit 2ff05b2b and related commit.
Reverted commit list
---------------------
- commit 2ff05b2b4e (oom: move oom_adj value from task_struct to mm_struct)
- commit 4d8b9135c3 (oom: avoid unnecessary mm locking and scanning for OOM_DISABLE)
- commit 8123681022 (oom: only oom kill exiting tasks with attached memory)
- commit 933b787b57 (mm: copy over oom_adj value at fork time)
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_sb_pseudo sets s_maxbytes to ~0ULL which becomes negative when cast
to a signed value. Fix it to use MAX_LFS_FILESIZE which casts properly
to a positive signed value.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Steve French <smfrench@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
net: restore gnet_stats_basic to previous definition
NETROM: Fix use of static buffer
e1000e: fix use of pci_enable_pcie_error_reporting
e1000e: WoL does not work on 82577/82578 with manageability enabled
cnic: Fix locking in init/exit calls.
cnic: Fix locking in start/stop calls.
bnx2: Use mutex on slow path cnic calls.
cnic: Refine registration with bnx2.
cnic: Fix symbol_put_addr() panic on ia64.
gre: Fix MTU calculation for bound GRE tunnels
pegasus: Add new device ID.
drivers/net: fixed drivers that support netpoll use ndo_start_xmit()
via-velocity: Fix test of mii_status bit VELOCITY_DUPLEX_FULL
rt2x00: fix memory corruption in rf cache, add a sanity check
ixgbe: Fix receive on real device when VLANs are configured
ixgbe: Do not return 0 in ixgbe_fcoe_ddp() upon FCP_RSP in DDP completion
netxen: free napi resources during detach
netxen: remove netxen workqueue
ixgbe: fix issues setting rx-usecs with legacy interrupts
can: fix oops caused by wrong rtnl newlink usage
...
The wake_up_process() of the new irq thread in __setup_irq() is too
early as the irqaction is not yet fully initialized especially
action->irq is not yet set. The interrupt thread might dereference the
wrong irq descriptor.
Move the wakeup after the action is installed and action->irq has been
set.
Reported-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
In 5e140dfc1f "net: reorder struct Qdisc
for better SMP performance" the definition of struct gnet_stats_basic
changed incompatibly, as copies of this struct are shipped to
userland via netlink.
Restoring old behavior is not welcome, for performance reason.
Fix is to use a private structure for kernel, and
teach gnet_stats_copy_basic() to convert from kernel to user land,
using legacy structure (struct gnet_stats_basic)
Based on a report and initial patch from Michael Spang.
Reported-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The static variable used by nr_call_to_digi might result in corruption if
multiple threads are trying to usee a node or neighbour via ioctl. Fixed
by having the caller pass a structure in. This is safe because nr_add_node
rsp. nr_add_neigh will allocate a permanent structure, if needed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit c8c00a6915
changed the exit paths in do_md_stop and was not quite
careful enough. There is one path were 'err' now needs
to be cleared but it isn't.
So setting an array to readonly (with mdadm --readonly) will
work, but will incorrectly report and error: ENXIO.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
security: define round_hint_to_min in !CONFIG_SECURITY
Security/SELinux: seperate lsm specific mmap_min_addr
SELinux: call cap_file_mmap in selinux_file_mmap
Capabilities: move cap_file_mmap to commoncap.c
The inotify_add_watch man page specifies that inotify_add_watch() will
return a non-negative integer. However, historically the inotify
watches started at 1, not at 0.
Turns out that the inotifywait program provided by the inotify-tools
package doesn't properly handle a 0 watch descriptor. In 7e790dd5 we
changed from starting at 1 to starting at 0. This patch starts at 1,
just like in previous kernels, but also just like in previous kernels
it's possible for it to wrap back to 0. This preserves the kernel
functionality exactly like it was before the patch (neither method broke
the spec)
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In f44aebcc the tail drop logic of events with no file backing
(q_overflow and in_ignored) was reversed so IN_IGNORED events would
never be tail dropped. This now means that Q_OVERFLOW events are NOT
tail dropped. The fix is to not tail drop IN_IGNORED, but to tail drop
Q_OVERFLOW.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
inotify decides if private data it passed to get added to an event was
used by checking list_empty(). But it's possible that the event may
have been dequeued and the private event removed so it would look empty.
The fix is to use the return code from fsnotify_add_notify_event rather
than looking at the list.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes warnings like this:
CC fs/proc/meminfo.o
In file included from /work/linux/include/linux/mmzone.h:20,
from /work/linux/include/linux/gfp.h:4,
from /work/linux/include/linux/mm.h:8,
from /work/linux/fs/proc/meminfo.c:5:
/work/linux/arch/mips/include/asm/page.h:36:1: warning: "HPAGE_SIZE" redefined
In file included from /work/linux/fs/proc/meminfo.c:2:
/work/linux/include/linux/hugetlb.h:107:1: warning: this is the location of the previous definition
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
An older test-box started hanging at the following point during
bootup:
[ 0.022996] Mount-cache hash table entries: 512
[ 0.024996] Initializing cgroup subsys debug
[ 0.025996] Initializing cgroup subsys cpuacct
[ 0.026995] Initializing cgroup subsys devices
[ 0.027995] Initializing cgroup subsys freezer
[ 0.028995] mce: CPU supports 5 MCE banks
I've bisected it down to commit 4efc0670 ("x86, mce: use 64bit
machine check code on 32bit"), which utilizes the MCE code on
32-bit systems too.
The problem is caused by this detail in my config:
# CONFIG_CPU_SUP_INTEL is not set
This disables the quirks in mce_cpu_quirks() but still enables
MCE support - which then hangs due to the missing quirk
workaround needed on this CPU:
if (c->x86 == 6 && c->x86_model < 0x1A && banks > 0)
mce_banks[0].init = 0;
The safe solution is to not initialize MCEs if we dont know on
what CPU we are running (or if that CPU's support code got
disabled in the config).
Also be a bit more defensive on 32-bit systems: dont do a
boot-time dump of pending MCEs not just on the specific system
that we found a problem with (Pentium-M), but earlier ones as
well.
Now this problem is probably not common and disabling CPU
support is rare - but still being more defensive in something
we turned on for a wide range of CPUs is prudent.
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: Message-ID: <4A88E3E4.40506@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On my legacy Pentium M laptop (Acer Extensa 2900) I get bogus MCE on a cold
boot with CONFIG_X86_NEW_MCE enabled, i.e. (after decoding it with mcelog):
MCE 0
HARDWARE ERROR. This is *NOT* a software problem!
Please contact your hardware vendor
CPU 0 BANK 1 MCG status:
MCi status:
Error overflow
Uncorrected error
Error enabled
Processor context corrupt
MCA: Data CACHE Level-1 UNKNOWN Error
STATUS f200000000000195 MCGSTATUS 0
[ The other STATUS values observed: f2000000000001b5 (... UNKNOWN error)
and f200000000000115 (... READ Error).
To verify that this is not a CONFIG_X86_NEW_MCE bug I also modified
the CONFIG_X86_OLD_MCE code (which doesn't log any MCEs) to dump
content of STATUS MSR before it is cleared during initialization. ]
Since the bogus MCE results in a kernel taint (which in turn disables
lockdep support) don't log boot MCEs on Pentium M (model == 13) CPUs
by default ("mce=bootlog" boot parameter can be be used to get the old
behavior).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The locking in xfs_iget_cache_hit currently has numerous problems:
- we clear the reclaim tag without i_flags_lock which protects
modifications to it
- we call inode_init_always which can sleep with pag_ici_lock
held (this is oss.sgi.com BZ #819)
- we acquire and drop i_flags_lock a lot and thus provide no
consistency between the various flags we set/clear under it
This patch fixes all that with a major revamp of the locking in
the function. The new version acquires i_flags_lock early and
only drops it once we need to call into inode_init_always or before
calling xfs_ilock.
This patch fixes a bug seen in the wild where we race modifying the
reclaim tag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Fix the header files to define round_hint_to_min() and to define
mmap_min_addr_handler() in the !CONFIG_SECURITY case.
Built and tested with !CONFIG_SECURITY
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently SELinux enforcement of controls on the ability to map low memory
is determined by the mmap_min_addr tunable. This patch causes SELinux to
ignore the tunable and instead use a seperate Kconfig option specific to how
much space the LSM should protect.
The tunable will now only control the need for CAP_SYS_RAWIO and SELinux
permissions will always protect the amount of low memory designated by
CONFIG_LSM_MMAP_MIN_ADDR.
This allows users who need to disable the mmap_min_addr controls (usual reason
being they run WINE as a non-root user) to do so and still have SELinux
controls preventing confined domains (like a web server) from being able to
map some area of low memory.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently SELinux does not check CAP_SYS_RAWIO in the file_mmap hook. This
means there is no DAC check on the ability to mmap low addresses in the
memory space. This function adds the DAC check for CAP_SYS_RAWIO while
maintaining the selinux check on mmap_zero. This means that processes
which need to mmap low memory will need CAP_SYS_RAWIO and mmap_zero but will
NOT need the SELinux sys_rawio capability.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently we duplicate the mmap_min_addr test in cap_file_mmap and in
security_file_mmap if !CONFIG_SECURITY. This patch moves cap_file_mmap
into commoncap.c and then calls that function directly from
security_file_mmap ifndef CONFIG_SECURITY like all of the other capability
checks are done.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
The function uv_acpi_madt_oem_check() has been marked __init,
the struct apic_x2apic_uv_x has been marked __refdata.
The aim is to address the following section mismatch messages:
WARNING: arch/x86/kernel/apic/built-in.o(.data+0x1368): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/kernel/built-in.o(.data+0x68e8): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/built-in.o(.text+0x7b36f): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_ioremap()
The function uv_acpi_madt_oem_check() references
the function __init early_ioremap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_ioremap is wrong.
WARNING: arch/x86/built-in.o(.text+0x7b38d): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_iounmap()
The function uv_acpi_madt_oem_check() references
the function __init early_iounmap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_iounmap is wrong.
WARNING: arch/x86/built-in.o(.data+0x8668): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
LKML-Reference: <200908161855.48302.lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
drivers/md/dm-log-userspace-transfer.c:110: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t'
Previously posted and acked, but apparently lost.
http://lkml.indiana.edu/hypermail/linux/kernel/0906.2/02074.html
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: dm-devel@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
