NBD doesn't work well with CFQ (or AS) schedulers, so let's default to
something else.
The two problems I have experienced with nbd and cfq are:
1) nbd hangs with cfq on RHEL 5 (2.6.18) -- this may well have been
fixed
There's a similar debian bug that has been filed as well:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=447638
There have been posts to nbd-general mailing list about problems with
cfq and nbd also.
2) nbd performs about 10% better (the last time I tested) with deadline
vs. cfq (the overhead of cfq doesn't provide much advantage to nbd [not
being a real disk], and you end up going through the I/O scheduler on
the nbd server anyway, so it makes sense that deadline is better with
nbd)
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we gather on-board devices from both DMI types 10 and 41, there is
a possibility that we list the same device twice. In order to not confuse
drivers, and also to save memory, make sure that we do not add duplicate
devices to the dmi_devices list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the "cmos" RTC, have /proc/driver/rtc say whether HPET based IRQ
emulation is in effect. Given the problems we've had with this particular
hardware maldesign (and the fact that most BIOS code seems not to provide
the IRQ routing needed to use the saner HPET modes), this should help
troubleshooting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a sequencing bug in spi driver pxa2xx_spi.c in which the chip select
for a transfer may be asserted before the clock polarity is set on the
interface. As a result of this bug, the clock signal may have the wrong
polarity at transfer start, so it may need to make an extra half transition
before the intended clock/data signals begin. (This probably means all
transfers are one bit out of sequence.)
This only occurs on the first transfer following a change in clock polarity
in systems using more than one more than one such polarity. The fix
assures that the clock mode is properly set before asserting chip select.
This bug was introduced in a patch merged on 2006/12/10, kernel 2.6.20.
The patch defines an additional bit in: include/asm-arm/arch-pxa/regs-ssp.h
for 2.6.25 and newer kernels but this addition must be made in:
include/asm-arm/arch-pxa/pxa-regs.h for kernels between 2.6.20 and 2.6.24,
inclusive
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atmel_spi driver does not initialize clock polarity correctly (except for
at91rm9200 CS0 channel) in some case.
The atmel_spi driver uses gpio-controlled chipselect. OTOH spi clock signal
is controlled by CSRn.CPOL bit, but this register controls clock signal
correctly only in 'real transfer' duration. At the time of cs_activate()
call, CSRn.CPOL will be initialized correctly, but the controller do not know
which channel is to be used next, so clock signal will stay at the inactive
state of last transfer. If clock polarity of new transfer and last transfer
was differ, new transfer will start with wrong clock signal state.
For example, if you started SPI MODE 2 or 3 transfer after SPI MODE 0 or 1
transfer, the clock signal state at the assertion of chipselect will be low.
Of course this will violates SPI transfer.
This patch is short term solution for this problem. It makes all CSRn.CPOL
match for the transfer before activating chipselect. For longer term, the
best fix might be to let NPCS0 stay selected permanently in MR and overwrite
CSR0 with to the new slave's settings before asserting CS.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should only return IRQ_HANDLED when we actually found something to
handle. This is important since the USART interrupt handler may be
shared with the timer interrupt on some chips.
Pointed-out-by: michael <trimarchi@gandalf.sssup.it>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following is a clean up and correction of the copyright holding
entities for the files associated with the intel iommu code.
Signed-off-by: <mgross@linux.intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current mainline, __devinit qpti_sbus_probe() still is calling __init
qpti_chain_add(). Change occurrences of __init to __devinit to fix.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert rough draft Marvell 6440 driver to a working driver.
Added support for SAS and SATA devices, hotplug, wide port, and expanders.
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make sure the restoration correctly restores the AR registers by
flipping the ARX register into index mode before doing anything.
Without this, some people have had the text mode restore all green.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current sas_scsi_clear_queue_lu() is wrongly checking for commands
which match the pointer to the one passed in. It should be checking for
commands which are on the same logical unit as the one passed in. Fix
this by checking target pointer and LUN for equality.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The clear nexus I_T and clear nexus I_T_L functions in the aic94xx
specify the SUSPEND_TX flag which causes the sequencer to be suspended
until it receives a RESUME_TX. Unfortunately, nothing ever sends the
resume, so the sequencer on the link is stopped forever, leading to
eventual timeouts and I/O errors.
Since clear nexus commands are only executed as part of error recovery,
it's perfectly fine to keep the sequencer running on the link ... as
soon as the recovery function is completed, we'll send it the commands
to retry.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove the now useless counting of adjacent pages from the debugging code in
to make it compile when DEBUG is set non-zero.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex_internal_copy copies an in-kernel buffer to a sg list by using
scsi_kmap_atomic_sg. Some functions calls stex_internal_copy with
sg_count in struct st_ccb, which is the value that dma_map_sg
returned. However it might be shorter than the actual number of sg
entries (if the IOMMU merged the sg entries).
scsi_kmap_atomic_sg doesn't see sg->dma_length so stex_internal_copy
should be called with the actual number of sg entries
(i.e. scsi_sg_count), because if the sg entries were merged,
stex_direct_copy wrongly think that the data length in the sg list is
shorter than the actual length.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex_direct_copy copies an in-kernel buffer to a sg list in order to
spoof some SCSI commands. stex_direct_copy calls dma_map_sg and then
stex_internal_copy with the value that dma_map_sg returned. It calls
scsi_kmap_atomic_sg to copy data.
scsi_kmap_atomic_sg doesn't see sg->dma_length so if dma_map_sg merges
sg entries, stex_internal_copy gets the smaller number of sg entries
than the acutual number, which means it wrongly think that the data
length in the sg list is shorter than the actual length.
stex_direct_copy shouldn't call dma_map_sg and it doesn't need since
this code path doesn't involve dma transfers. This patch removes
stex_direct_copy and simply calls stex_internal_copy with the actual
number of sg entries.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 3163f725a5 introduced locking in
lpfc_sli_hbqbuf_fill_hbqs, but missed unlocking on one exit.
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
the check in the residual case has an incorrect test of scsi_status
(the logic is reversed, it should be scsi_status != 0 instead of
!scsi_status. Since we checked a few lines above that scsi_status was
non-zero, just eliminate this test
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The libsas error handler has two fairly fatal bugs
1. scsi_sas_task_done calls scsi_eh_finish_cmd() too early. This
happens if the task completes after it has been aborted but before
the error handler starts up. Because scsi_eh_finish_cmd()
decrements host_failed and adds the task to the done list, the
error handler start check (host_failed == host_busy) never passes
and the eh never starts.
2. The multiple task completion paths sas_scsi_clear_queue_... all
simply delete the task from the error queue. This causes it to
disappear into the ether, since a command must be placed on the
done queue to be finished off by the error handler. This behaviour
causes the HBA to hang on pending commands.
Fix 1. by moving the SAS_TASK_STATE_ABORTED check to an exit clause at
the top of the routine and calling ->scsi_done() unconditionally (it
is a nop if the timer has fired). This keeps the task in the error
handling queue until the eh starts.
Fix 2. by making sure every task goes through task complete followed
by scsi_eh_finish_cmd().
Tested this by firing resets across a disk running a hammer test (now
it actually survives without hanging the system)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
arcmsr_iop_message_xfer() is called from atomic context under the
queuecommand scsi_host_template handler. James Bottomley pointed out
that the current GFP_KERNEL|GFP_DMA flags are wrong: firstly we are in
atomic context, secondly this memory is not used for DMA.
Also removed some unneeded casts.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ioc->name is used in the printk's after ioc has been freed. Free
after prinks to fix this.
This patch fixes two use-after-free's introduced by
commit e78d5b8f1e and spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the following needlessly global functions static:
- __iscsi_unblock_session()
- iscsi_session_state_name()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the needlessly global lpfc_disable_node() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
modules: do not try to add sysfs attributes if !CONFIG_SYSFS
POWERPC: fix typo in pseries/power.c
PM: Remove unbalanced mutex_unlock() from dpm_resume()
UIO: fix Greg's stupid changes
stable_kernel_rules: fix must already be in mainline
ide: mark "ide=reverse" option as obsolete
Driver core: Fix error handling in bus_add_driver().
driver-core: fix kernel-doc function parameters
cpufreq: fix kobject reference count handling
slabinfo: fall back from /sys/kernel/slab to /sys/slab
Fix broken utf-8 encodings in ja_JP translation of stable_kernel_rules.txt
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Fix wrong reference counter check for proc_dir_entry
PCI: fix up setup-bus.c #ifdef
PCI: don't load acpi_php when acpi is disabled
PCI: quirks: set 'En' bit of MSI Mapping for devices onHT-based nvidia platform
PCI: kernel-doc: fix pci-acpi warning
PCI: irq: patch for Intel ICH10 DeviceID's
PCI: pci_ids: patch for Intel ICH10 DeviceID's
PCI: AMD SATA IDE mode quirk
PCI: drivers/pcmcia/i82092.c: fix up after pci_bus_region changes
PCI: hotplug: acpiphp_ibm: Remove get device information
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (23 commits)
ehci-fsl: add PPC_MPC837x to default y
USB: POWERPC: ehci: fix ppc build
USB: usb-storage: don't access beyond the end of the sg buffer
USB: quirks and unusual_devs entry for Actions flash drive
USB: usb-storage: unusual_devs entry for Oracom MP3 player
USB: serial: move zte MF330 from sierra to option
USB: add new vernier product id to ldusb.c
USB: gadget: queue usb USB_CDC_GET_ENCAPSULATED_RESPONSE message
USB: Add another Novatel U727 ID to the device table for usbserial
USB: storage: Nikon D80 new FW still needs Fixup
USB: usb-storage: don't clear-halt when Get-Max-LUN stalls
USB: option: Added vendor id for Dell 5720 broadband modem
USB: option: Add Kyocera KPC680 ids
USB: quirks for known quirky audio devices
USB: fix previous sparse fix which was incorrect
USB: fix error handling in trancevibrator
USB: g_printer, fix empty if statement
USB: ehci-fsl: mpc834x config symbol is PPC_MPC834x, not MPC834x
USB: fix usb open suspend race in cdc-acm
USB: usb: yet another Dell wireless CDMA/EVDO modem
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4835/1: Fix stale comment in struct machine_desc description
[ARM] 4829/1: add .get method to pxa-cpufreq to silence a warning
[ARM] 4828/1: fix 3 warnings in drivers/video/pxafb.c
[ARM] 4827/1: fix two warnings in drivers/i2c/busses/i2c-pxa.c
[ARM] 4826/1: Orion: Register the RTC interrupt on the TS-209
[ARM] pxa: fix clock lookup to find specific device clocks
The below implements the getgeo hook for Xen block devices. Extracted
from the xen-unstable tree where it has been used for ages.
It is useful to have because it allows things like grub2 (used by the
Debian installer images) to work in a guest domain without having to
sprinkle Xen specific hacks around the place.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts USB_EHCI_FSL config option into the verbose
bool, so we'll able to select it for other freescale processors
with built-in EHCI controller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, this setup:
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_HCD_PPC_OF=y
Will fail to build:
CC drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-hcd.c:1018:2: error: #error "missing bus glue for ehci-hcd"
make[3]: *** [drivers/usb/host/ehci-hcd.o] Error 1
ehci-hcd.c actually contains OF_PLATFORM_DRIVER glue, so error is bogus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1035) fixes a bug in usb_stor_access_xfer_buf() (the bug
was originally found by Boaz Harrosh): The routine must not attempt to
write beyond the end of a scatter-gather list or beyond the number of
bytes requested. It also fixes up the formatting of a few comments
and similar whitespace issues.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1033) adds a quirks entry and an unusual_devs entry for
the Actions Semiconductor flash drive. This device has a 64-byte
string descriptor, which it doesn't terminate with a 0-length packet.
Oddly enough, the reporter's logs show that when the device was
plugged in at boot time, it changes its behavior completely -- it uses
a different product ID, product string descriptor, and bDeviceClass.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1034) was written by Leonid Petrov, reported by Robert
Spitzenpfeil, and updated by me. It adds an unusual_devs entry with
the IGNORE_RESIDUE flag for the Oracom MP3 player. Together with the
change to the Get-Max-LUN routine in as1032, it makes the player usable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the Onda H600/ZTE MF33 device from the sierra driver to the option
driver.
The reason it was moved is because the sierra driver is starting to support
more and more sierra proprietary features, so it makes more sense to keep
sierra only devices in there.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have a new ldusb device to go into the device table. Jiri has merged
the change for hiddev quirks already.
From: Stephen Ware <stephen.ware@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0cf4f2de0a introduced a bug, which
prevents sending an USB_CDC_GET_ENCAPSULATED_RESPONSE message. This
breaks the RNDIS initialization (especially / only Windoze machines
dislike this behavior...).
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new BCD numbers for Nikon D80 Firmware revision v1.10 to the
unusual_devs.h file.
Signed-off-by: Konstantin Kletschke <konsti@ku-gbr.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1032) removes the Clear-Halt calls in
usb_stor_Bulk_max_lun(). Evidently some devices (such as the Oracom
MP3 player) really don't like to receive these requests when their
bulk endpoints aren't halted.
The only reason for adding them originally was to get an ancient
ZIP-100 drive to work. But since this device has only a single LUN,
we don't need to send it a Get-Max-LUN request at all. Adding an
unusual_devs entry for the ZIP-100 with the SINGLE_LUN flag set will
cause this step to be skipped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is a small patch to add support for a rebranded Novatel modem (see
http://ubuntuforums.org/archive/index.php/t-608388.html for details).
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RESET_RESUME entries for some sound devices that need it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous fix for a "sparse" warning in ehci_urb_dequeue() was
incorrect. After rescheduling interrupt transfers it returned the
URB's completion status, not status for the dequeue operation itself.
This patch resolves that issue, cleans up the code in the reschedule
path, and shrinks the object code by a dozen bytes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
trancevibrator should not pretend success if it returns an error.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A bug every C programmer makes at some point in time...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
