A panic was observed when the device is failed to resume properly,
and there are no running interfaces. ieee80211_reconfig tries
to restart STA timers on unassociated state.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were uploading different firmwares to the hardware until finding
responding one.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to support pre-populating the P1K cache in
iwlwifi hardware for WoWLAN, we need to calculate
the P1K for the current IV32. Allow drivers to get
the P1K for any given IV32 instead of for a given
packet, but keep the packet-based version around as
an inline.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to implement GTK rekeying, the device needs
to be able to encrypt frames with the right PN/IV and
check the PN/IV in RX frames. To be able to tell it
about all those counters, we need to be able to get
them from mac80211, this adds the required API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current rx->queue value is slightly confusing.
It is set to 16 on non-QoS frames, including data,
and then used for sequence number and PN/IV checks.
Until recently, we had a TKIP IV checking bug that
had been introduced in 2008 to fix a seqno issue.
Before that, we always used TID 0 for checking the
PN or IV on non-QoS packets.
Go back to the old status for PN/IV checks using
the TID 0 counter for non-QoS by splitting up the
rx->queue value into "seqno_idx" and "security_idx"
in order to avoid confusion in the future. They
each have special rules on the value used for non-
QoS data frames.
Since the handling is now unified, also revert the
special TKIP handling from my patch
"mac80211: fix TKIP replay vulnerability".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LCN-PHY was found in 14e4:4727 card. It uses LCN/1 and 0x2064/1 radio.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has a defnition of AES_BLOCK_SIZE and
multiple definitions of AES_BLOCK_LEN. Remove
them all and use crypto/aes.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Older cores had unique PHY. This is not true anymore for newer ones.
For example core rev 16 can be LP, SSLPN or N (PHY).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like TKIP and CCMP, CMAC has the PN race.
It might not actually be possible to hit it now
since there aren't multiple ACs for management
frames, but fix it anyway.
Also move scratch buffers onto the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we can process multiple packets at the
same time for different ACs, but the PN is
allocated from a single counter, we need to
use an atomic value there. Use atomic64_t to
make this cheaper on 64-bit platforms, other
platforms will support this through software
emulation, see lib/atomic64.c.
We also need to use an on-stack scratch buf
so that multiple packets won't corrupt each
others scratch buffers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our current TKIP code races against itself on TX
since we can process multiple packets at the same
time on different ACs, but they all share the TX
context for TKIP. This can lead to bad IVs etc.
Also, the crypto offload helper code just obtains
the P1K/P2K from the cache, and can update it as
well, but there's no guarantee that packets are
really processed in order.
To fix these issues, first introduce a spinlock
that will protect the IV16/IV32 values in the TX
context. This first step makes sure that we don't
assign the same IV multiple times or get confused
in other ways.
Secondly, change the way the P1K cache works. I
add a field "p1k_iv32" that stores the value of
the IV32 when the P1K was last recomputed, and
if different from the last time, then a new P1K
is recomputed. This can cause the P1K computation
to flip back and forth if packets are processed
out of order. All this also happens under the new
spinlock.
Finally, because there are argument differences,
split up the ieee80211_get_tkip_key() API into
ieee80211_get_tkip_p1k() and ieee80211_get_tkip_p2k()
and give them the correct arguments.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split tx_queue_count to count per-AC skb's queued, instead of relying on
the skb-queue len. The skb queues used were only valid in STA-mode, as
AP-mode uses per-link queues.
This fixes a major regression in AP-mode, caused by the patch
"wl12xx: implement Tx watermarks per AC". With that patch applied, we
effectively had no regulation of Tx queues in AP-mode. Therefore a
sustained high rate of Tx could cause exhaustion of the skb memory pool.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
This would exactly mimic the behaviour of the legacy vendor driver which
also doesn't go in powersave mode if there are still TX frames that are not
transmitted.
This should make powersaving and rt2x00 a better couple.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sitecom WLA4000 (USB ID 0x0df6:0x0060) is an RT3072 chipset.
Sitecom WLA5000 (USB ID 0x0df6:0x0062) is an RT3572 chipset.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Wim Vander Schelden <wim@fixnum.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently a lot of actions that can be done without the queue's tx lock
being held are done inside the locked area.
Move them out to have a leaner and meaner code that operates while the
tx lock is being held.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions that create the tx descriptor structure do not operate on
a queue entry at all. Signal this fact in the code by not providing a
queue entry as a parameter, but the rt2x00 device structure and the skb
directly.
This patch is a preparation for reducing the time a queue is locked for
a tx operation.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00 driver gets frequent occurrences of the following error message
when operating under load:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the
non-full queue 2.
This is caused by simultaneous attempts from mac80211 to send a frame via
rt2x00, which are not properly serialized inside rt2x00queue_write_tx_frame,
causing the second frame to fail sending with the above mentioned error
message.
Fix this by introducing a per-queue spinlock to serialize the TX operations
on that queue.
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must not init it like clientmode one, it would break device (tested
by Hauke on BCM4718). Add stub hostmode driver for now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDIO aggregation buffer size has been modified to an optimum
value which gives good throughput results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a stray "undefined" string in the array, get rid of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the necessary mac80211 APIs to support
GTK rekey offload, mirroring the functionality
from cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In certain circumstances, like WoWLAN scenarios,
devices may implement (partial) GTK rekeying on
the device to avoid waking up the host for it.
In order to successfully go through GTK rekeying,
the KEK, KCK and the replay counter are required.
Add API to let the supplicant hand the parameters
to the driver which may store it for future GTK
rekey operations.
Note that, of course, if GTK rekeying is done by
the device, the EAP frame must not be passed up
to userspace, instead a rekey event needs to be
sent to let userspace update its replay counter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When in suspend/wowlan, devices might implement crypto
offload differently (more features), and might require
reprogramming keys for the WoWLAN (as it is the case
for Intel devices that use another uCode image). Thus
allow the driver to iterate all keys in this context.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSB code reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSB code reads PCI revision ID from the PCI configuration register while
it's already stored by the PCI subsystem in the 'revision' field of 'struct
pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a memory barrier to ensure the writes to the ring memory
are committed before the DMA ring pointer is updated.
We do a similar thing on the TX side already.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This socket protocol is used to perform data exchange with NFC
targets.
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NFC generic netlink interface exports the NFC control operations
to the user space.
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NFC subsystem core is responsible for providing the device driver
interface. It is also responsible for providing an interface to the control
operations and data exchange.
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver can't support WoWLAN in the current
state, this patch allows it to return 1 from the
suspend callback to do the normal deconfiguration
instead of using suspend/resume calls. Note that
if it does this, resume won't be called.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSB code reads PCI revision ID register as 16-bit entity while the register
is actually 8-bit only (the next 8 bits are the programming interface register).
Fix the read and make the 'rev' field of 'struct ssb_boardinfo' 8-bit as well,
to match the register size.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In routine rtl92de_hw_init(), there are two places where a failure is
not handled correctly.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a number of loops to implement delays. These are replaced with
single calls to mdelay().
The need for a fix was noted by Andrew Morton <akpm@linux-foundation.org>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
