The following case may lead to o2net_wq and o2hb thread deadlock on
o2hb_callback_sem.
Currently there are 2 nodes say N1, N2 in the cluster. And N2 down, at
the same time, N3 tries to join the cluster. So N1 will handle node
down (N2) and join (N3) simultaneously.
o2hb o2net_wq
->o2hb_do_disk_heartbeat
->o2hb_check_slot
->o2hb_run_event_list
->o2hb_fire_callbacks
->down_write(&o2hb_callback_sem)
->o2net_hb_node_down_cb
->flush_workqueue(o2net_wq)
->o2net_process_message
->dlm_query_join_handler
->o2hb_check_node_heartbeating
->o2hb_fill_node_map
->down_read(&o2hb_callback_sem)
No need to take o2hb_callback_sem in dlm_query_join_handler,
o2hb_live_lock is enough to protect live node map.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Cc: xMark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: jiangyiwen <jiangyiwen@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Firing quorum before connection established can cause unexpected node to
reboot.
Assume there are 3 nodes in the cluster, Node 1, 2, 3. Node 2 and 3 have
wrong ip address of Node 1 in cluster.conf and global heartbeat is enabled
in the cluster. After the heatbeats are started on these three nodes,
Node 1 will reboot due to quorum fencing. It is similar case if Node 1's
networking is not ready when starting the global heartbeat.
The reboot is not friendly as customer is not fully ready for ocfs2 to
work. Fix it by not allowing firing quorum before the connection is
established. In this case, ocfs2 will wait until the wrong configuration
is fixed or networking is up to continue. Also update the log to guide
the user where to check when connection is not built for a long time.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce boilerplate code by using seq_open_private() instead of seq_open()
Signed-off-by: Rob Jones <rob.jones@codethink.co.uk>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce boilerplate code by using seq_open_private() instead of seq_open()
Note that the code in and using sc_common_open() has been quite
extensively changed. Not least because there was a latent memory leak in
the code as was: if sc_common_open() failed, the previously allocated
buffer was not freed.
Signed-off-by: Rob Jones <rob.jones@codethink.co.uk>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce boilerplate code by using seq_open_private() instead of seq_open()
Signed-off-by: Rob Jones <rob.jones@codethink.co.uk>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the branch that free res->lockname.name because the condition
is never satisfied when jump to label error.
Signed-off-by: joyce.xue <xuejiufei@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dlm_lockres_put() should be called without &res->spinlock, otherwise a
deadlock case may happen.
spin_lock(&res->spinlock)
...
dlm_lockres_put
->dlm_lockres_release
->dlm_print_one_lock_resource
->spin_lock(&res->spinlock)
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In o2net_init, if malloc failed, it directly returns -ENOMEM. Then
o2quo_exit won't be called in init_o2nm.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: joyce.xue <xuejiufei@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ocfs2_inode_info->ip_clusters and ocfs2_dinode->id1.bitmap1.i_total are
defined as type u32, so the shift left operations may overflow if volume
size is large, for example, 2TB and cluster size is 1MB.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Alex Chen <alex.chen@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactoring error handling in dlm_alloc_ctxt to simplify code.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Alex Chen <alex.chen@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is supposed to zero pv_minor.
Reported-by: Himangi Saraogi <himangi774@gmail.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fs/ntfs/debug.c:124: WARNING: space prohibited between function name and
open parenthesis '('
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman's commit 2457aec637 ("mm: non-atomically mark page accessed
during page cache allocation where possible") removed mark_page_accessed()
calls from NTFS without updating the matching find_lock_page() to
find_get_page_flags(GFP_LOCK | FGP_ACCESSED) thus causing the page to
never be marked accessed.
This patch fixes that.
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the use of the IRQF_DISABLED flag
from arch/m32r/kernel/time.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to commit 80af258867 ("fanotify: groups can specify their
f_flags for new fd"), file descriptors created as part of file access
notification events inherit flags from the event_f_flags argument passed
to syscall fanotify_init(2)[1].
Unfortunately O_CLOEXEC is currently silently ignored.
Indeed, event_f_flags are only given to dentry_open(), which only seems to
care about O_ACCMODE and O_PATH in do_dentry_open(), O_DIRECT in
open_check_o_direct() and O_LARGEFILE in generic_file_open().
It's a pity, since, according to some lookup on various search engines and
http://codesearch.debian.net/, there's already some userspace code which
use O_CLOEXEC:
- in systemd's readahead[2]:
fanotify_fd = fanotify_init(FAN_CLOEXEC|FAN_NONBLOCK, O_RDONLY|O_LARGEFILE|O_CLOEXEC|O_NOATIME);
- in clsync[3]:
#define FANOTIFY_EVFLAGS (O_LARGEFILE|O_RDONLY|O_CLOEXEC)
int fanotify_d = fanotify_init(FANOTIFY_FLAGS, FANOTIFY_EVFLAGS);
- in examples [4] from "Filesystem monitoring in the Linux
kernel" article[5] by Aleksander Morgado:
if ((fanotify_fd = fanotify_init (FAN_CLOEXEC,
O_RDONLY | O_CLOEXEC | O_LARGEFILE)) < 0)
Additionally, since commit 48149e9d3a ("fanotify: check file flags
passed in fanotify_init"). having O_CLOEXEC as part of fanotify_init()
second argument is expressly allowed.
So it seems expected to set close-on-exec flag on the file descriptors if
userspace is allowed to request it with O_CLOEXEC.
But Andrew Morton raised[6] the concern that enabling now close-on-exec
might break existing applications which ask for O_CLOEXEC but expect the
file descriptor to be inherited across exec().
In the other hand, as reported by Mihai Dontu[7] close-on-exec on the file
descriptor returned as part of file access notify can break applications
due to deadlock. So close-on-exec is needed for most applications.
More, applications asking for close-on-exec are likely expecting it to be
enabled, relying on O_CLOEXEC being effective. If not, it might weaken
their security, as noted by Jan Kara[8].
So this patch replaces call to macro get_unused_fd() by a call to function
get_unused_fd_flags() with event_f_flags value as argument. This way
O_CLOEXEC flag in the second argument of fanotify_init(2) syscall is
interpreted and close-on-exec get enabled when requested.
[1] http://man7.org/linux/man-pages/man2/fanotify_init.2.html
[2] http://cgit.freedesktop.org/systemd/systemd/tree/src/readahead/readahead-collect.c?id=v208#n294
[3] https://github.com/xaionaro/clsync/blob/v0.2.1/sync.c#L1631https://github.com/xaionaro/clsync/blob/v0.2.1/configuration.h#L38
[4] http://www.lanedo.com/~aleksander/fanotify/fanotify-example.c
[5] http://www.lanedo.com/2013/filesystem-monitoring-linux-kernel/
[6] http://lkml.kernel.org/r/20141001153621.65e9258e65a6167bf2e4cb50@linux-foundation.org
[7] http://lkml.kernel.org/r/20141002095046.3715eb69@mdontu-l
[8] http://lkml.kernel.org/r/20141002104410.GB19748@quack.suse.cz
Link: http://lkml.kernel.org/r/cover.1411562410.git.ydroneaud@opteya.com
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Mihai Don\u021bu <mihai.dontu@gmail.com>
Cc: Pádraig Brady <P@draigBrady.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Michael Kerrisk-manpages <mtk.manpages@gmail.com>
Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Cc: Richard Guy Briggs <rgb@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some failure paths we may attempt to free user context even if it
wasn't assigned yet. This will cause a NULL ptr deref and a kernel BUG.
The path I was looking at is in inotify_new_group():
oevent = kmalloc(sizeof(struct inotify_event_info), GFP_KERNEL);
if (unlikely(!oevent)) {
fsnotify_destroy_group(group);
return ERR_PTR(-ENOMEM);
}
fsnotify_destroy_group() would get called here, but
group->inotify_data.user is only getting assigned later:
group->inotify_data.user = get_current_user();
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: John McCutchan <john@johnmccutchan.com>
Cc: Robert Love <rlove@rlove.org>
Cc: Eric Paris <eparis@parisplace.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- a cleanup series to get rid of mindlessly copied code.
- another bunch of new pointlessly different interrupt chip drivers.
Adding homebrewn irq chips (and timers) to SoCs must provide a
value add which is beyond the imagination of mere mortals.
- the usual SoC irq controller updates, IOW my second cat herding
project"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
irqchip: gic-v3: Implement CPU PM notifier
irqchip: gic-v3: Refactor gic_enable_redist to support both enabling and disabling
irqchip: renesas-intc-irqpin: Add minimal runtime PM support
irqchip: renesas-intc-irqpin: Add helper variable dev = &pdev->dev
irqchip: atmel-aic5: Add sama5d4 support
irqchip: atmel-aic5: The sama5d3 has 48 IRQs
Documentation: bcm7120-l2: Add Broadcom BCM7120-style L2 binding
irqchip: bcm7120-l2: Add Broadcom BCM7120-style Level 2 interrupt controller
irqchip: renesas-irqc: Add binding docs for new R-Car Gen2 SoCs
irqchip: renesas-irqc: Add DT binding documentation
irqchip: renesas-intc-irqpin: Document SoC-specific bindings
openrisc: Get rid of handle_IRQ
arm64: Get rid of handle_IRQ
ARM: omap2: irq: Convert to handle_domain_irq
ARM: imx: tzic: Convert to handle_domain_irq
ARM: imx: avic: Convert to handle_domain_irq
irqchip: or1k-pic: Convert to handle_domain_irq
irqchip: atmel-aic5: Convert to handle_domain_irq
irqchip: atmel-aic: Convert to handle_domain_irq
irqchip: gic-v3: Convert to handle_domain_irq
...
Pull timer updates from Thomas Gleixner:
"Nothing really exciting this time:
- a few fixlets in the NOHZ code
- a new ARM SoC timer abomination. One should expect that we have
enough of them already, but they insist on inventing new ones.
- the usual bunch of ARM SoC timer updates. That feels like herding
cats"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: arm_arch_timer: Consolidate arch_timer_evtstrm_enable
clocksource: arm_arch_timer: Enable counter access for 32-bit ARM
clocksource: arm_arch_timer: Change clocksource name if CP15 unavailable
clocksource: sirf: Disable counter before re-setting it
clocksource: cadence_ttc: Add support for 32bit mode
clocksource: tcb_clksrc: Sanitize IRQ request
clocksource: arm_arch_timer: Discard unavailable timers correctly
clocksource: vf_pit_timer: Support shutdown mode
ARM: meson6: clocksource: Add Meson6 timer support
ARM: meson: documentation: Add timer documentation
clocksource: sh_tmu: Document r8a7779 binding
clocksource: sh_mtu2: Document r7s72100 binding
clocksource: sh_cmt: Document SoC specific bindings
timerfd: Remove an always true check
nohz: Avoid tick's double reprogramming in highres mode
nohz: Fix spurious periodic tick behaviour in low-res dynticks mode
Pull timer fixes from Ingo Molnar:
"Main changes:
- Fix the deadlock reported by Dave Jones et al
- Clean up and fix nohz_full interaction with arch abilities
- nohz init code consolidation/cleanup"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: nohz full depends on irq work self IPI support
nohz: Consolidate nohz full init code
arm64: Tell irq work about self IPI support
arm: Tell irq work about self IPI support
x86: Tell irq work about self IPI support
irq_work: Force raised irq work to run on irq work interrupt
irq_work: Introduce arch_irq_work_has_interrupt()
nohz: Move nohz full init call to tick init
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
Starting with 3.18, we are merging SoC-specific changes for arm64 through
the arm-soc tree, like we have been doing for arm32.
This time, there is only one set of changes, adding support for the
Cavium "Thunder" Soc family. Since the changes are relatively small,
this includes Kconfig, defconfig and DT changes.
If all goes well, we will never require adding actual C source code
for platform support in arm64, given that the architecture is more
clearly defined and we have moved out a lot of the platform specifics
into device drivers for arm32 already.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=sqqq
-----END PGP SIGNATURE-----
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM64 SoC changes from Arnd Bergmann:
"Starting with 3.18, we are merging SoC-specific changes for arm64
through the arm-soc tree, like we have been doing for arm32.
This time, there is only one set of changes, adding support for the
Cavium "Thunder" Soc family. Since the changes are relatively small,
this includes Kconfig, defconfig and DT changes.
If all goes well, we will never require adding actual C source code
for platform support in arm64, given that the architecture is more
clearly defined and we have moved out a lot of the platform specifics
into device drivers for arm32 already"
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64, defconfig: Enable Cavium Thunder SoC in defconfig
arm64, thunder: Add Kconfig option for Cavium Thunder SoC Family
arm64, thunder: Document devicetree bindings for Cavium Thunder SoC
arm64, thunder: Add initial dts for Cavium Thunder SoC
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into drivers
directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAVDWWQGCrR//JCVInAQKX7Q//bDkoseKCZsGaXN7vfQ2YhT3SAc52mROV
YQKdNmtMUrHqDgngATZTx5ogOh1hInnqueFjGGhfMYsHQO1Vj8+odj0r+4jhjuUY
3YfY+qZ+91tq33JlUOhKn+mfVMdxJc8XarGgR6MSWYkqWVYCtLtBluum7hKm2UJ6
/e4hd2zzImX5ATwj/LXWLx5eTf1qAVFGWzNUph1DrW+1V5lOu58X4gKwk1QOCVEh
Pa0GV9oRTkjoswwz9drzjeFtie2yofQ2mygj6QKxg5NsosIF0+B8kJ61Sxwg56Ak
tF+qn1hGtB2cDQkpxK4o2cZgCELhkh5Aqgol/vZUS1DMBSUEGCV9PPp2eOW83r3B
0zsTgsShyVcTh7khdpQmHNRigvcc7e69LaAGC4o/RxaZpCU/LUNCQ+/iqVExSE8A
VNEXr+JNxGxhj3m9KUHuEktdWx1oNvaYR8Rr4RPr6EWR8R6emJ04I7kXInvzhJZL
HOGh75vSuAU83FrsP8fFRLadoHNVDXylAs38BPfGEMngVpjvwJLgQ3+729CwW+Q4
+xQXAKSwKfr8xA8eg6wBSbFcwnEW4QwRqFqQ5XPw7zTZkCZbiLtvn3JpI5bH5A5Q
/d2D+M2vFbB7VbWJBM4etO95eNS/pfhqJhcQh4t0DjXjoW6WqLiHCxhEx8Ogfvop
/4ckyGvtEOI=
=POJD
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
As usual, this is the largest branch, though this time a little under
half of the total changes with 307 individual non-merge changesets.
The largest changes are the addition of new machines, in particular
the Tegra based Chromebook, the Renesas r8a7794 SoC, and DT support
for the old i.MX1 platform.
Other changes include
- at91: various sam9 and sama5 updates
- exynos: much extended Peach Pi/Pit (Chromebook 2) support
- keystone: new peripherals
- meson: added DT for meson6 SoC
- mvebu: new device support for Armada 370/375
- qcom: improved support for IPQ8064 and MSM8x60
- rockchip: much improved support for rk3288
- shmobile: lots of updates all over the place
- sunxi: dts license change
- sunxi: more a23 device support
- vexpress: CLCD DT description
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAVDWVG2CrR//JCVInAQJmARAAnU2I4VpJHlBeHC4CYr/GdRq0NqiFvQ38
7N/zevUI4l150DtejltbOX71JGM9vD3hq8VXZYBCEpTbG4el9PzAq28Fomtt4tmC
PGbczQY8ZMvY1/MOT3XLZAd3TSUL0TZRt97t9bdLif6QyPafel5o2pd8D2OG7h+L
Awtyk9LobT9jU3muFX3ZUfB3Gg2sNKphZjox9Le3gVjGd6g5teEqqMAehK2Y7ArJ
kixrKck4vgduDdZe59o2yApAUsfIQv/joqu68jv3MUQrKmk4s543+rIdGDuLF5bz
mEo7qtMXujoNaF3CyLYNEF2ZExIOJDdtmrwjHY8oKIFtIeI/faIJmeSChwa6794t
Njj5bbnL0Pt61l4gUSFk2hUFo28gpiEB+Mm0R4E1hdoG15Iv6E+lpy44EmEmfz1c
9h0sATNGUrz18IrUk7jI1WwIaEJUwkbZ+8wKuWtvH+Z+mFA4ZlDykVcnVuELixpb
vKmI3kcmEw2RsJjkYq3LcgXXQevE4mHRR1ow59yXTY6OR1LmVb7odKUwbrweofQO
eytVb1deMeYXrBXT5/j6WmrlyDbYcuGsjO4WidT+zwYUiAMCE6bTpNwUWqumVEUv
LjCBaN6BRIb89EBwt4xIvIu7ir9hNNRZnD8aa4afSzIYxknzZy73pjjT2+wu7jbU
m15TwYyQG4E=
=2Sq1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, this is the largest branch, though this time a little under
half of the total changes with 307 individual non-merge changesets.
The largest changes are the addition of new machines, in particular
the Tegra based Chromebook, the Renesas r8a7794 SoC, and DT support
for the old i.MX1 platform.
Other changes include
- at91: various sam9 and sama5 updates
- exynos: much extended Peach Pi/Pit (Chromebook 2) support
- keystone: new peripherals
- meson: added DT for meson6 SoC
- mvebu: new device support for Armada 370/375
- qcom: improved support for IPQ8064 and MSM8x60
- rockchip: much improved support for rk3288
- shmobile: lots of updates all over the place
- sunxi: dts license change
- sunxi: more a23 device support
- vexpress: CLCD DT description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (308 commits)
ARM: DTS: meson: update DTSI to add watchdog node
ARM: dts: keystone-k2l: fix mdio io start address
ARM: dts: keystone-k2e: fix mdio io start address
ARM: dts: keystone-k2e: update usb1 node for dma properties
ARM: dts: keystone: fix io range for usb_phy0
Revert "Merge tag 'hix5hd2-dt-for-3.18' of git://github.com/hisilicon/linux-hisi into next/dt"
Revert "ARM: dts: hix5hd2: add wdg node"
ARM: dts: add rk3288 i2s controller
ARM: vexpress: Add CLCD Device Tree properties
ARM: bcm2835: add I2S pinctrl to device tree
ARM: meson: documentation: add bindings documentation
ARM: meson: dts: add basic Meson/Meson6/Meson6-atv1200 DTSI/DTS
ARM: dts: mt6589: Change compatible string for GIC
ARM: dts: mediatek: Add compatible property for aquaris5
ARM: dts: mt6589-aquaris5: Add boot argument earlyprintk
ARM: dts: mt6589: Fix typo in GIC unit address
ARM: dts: Build dtb for Mediatek board
ARM: dts: keystone: fix bindings for pcie and usb clock nodes
ARM: dts: keystone: k2l: Fix chip selects for SPI devices
ARM: dts: keystone: add dsp gpio controllers nodes
...
New and updated SoC support. Among the things new for this release are:
- at91: Added support for the new SAMA5D4 SoC, following the earlier SAMA5D3
- bcm: Added support for BCM63XX family of DSL SoCs
- hisi: Added support for HiP04 server-class SoC
- meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform
- shmobile: added support for new r8a7794 (R-Car E2) automotive SoC
Noteworthy changes to existing SoC support are:
- imx: convert i.MX1 to device tree
- omap: lots of power management work
- omap: base support to enable moving to standard UART driver
- shmobile: lots of progress for multiplatform support, still ongoing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ZHtj
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support. Among the things new for this release
are:
- at91: Added support for the new SAMA5D4 SoC, following the earlier
SAMA5D3
- bcm: Added support for BCM63XX family of DSL SoCs
- hisi: Added support for HiP04 server-class SoC
- meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform
- shmobile: added support for new r8a7794 (R-Car E2) automotive SoC
Noteworthy changes to existing SoC support are:
- imx: convert i.MX1 to device tree
- omap: lots of power management work
- omap: base support to enable moving to standard UART driver
- shmobile: lots of progress for multiplatform support, still
ongoing"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (171 commits)
ARM: hisi: depend on ARCH_MULTI_V7
CNS3xxx: Fix debug UART.
ARM: at91: fix nommu build regression
ARM: meson: add basic support for MesonX SoCs
ARM: meson: debug: add debug UART for earlyprintk support
irq: Export handle_fasteoi_irq
ARM: mediatek: Add earlyprintk support for mt6589
ARM: hisi: Fix platmcpm compilation when ARMv6 is selected
ARM: debug: fix alphanumerical order on debug uarts
ARM: at91: document Atmel SMART compatibles
ARM: at91: add sama5d4 support to sama5_defconfig
ARM: at91: dt: add device tree file for SAMA5D4ek board
ARM: at91: dt: add device tree file for SAMA5D4 SoC
ARM: at91: SAMA5D4 SoC detection code and low level routines
ARM: at91: introduce basic SAMA5D4 support
clk: at91: add a driver for the h32mx clock
ARM: pxa3xx: provide specific platform_devices for all ssp ports
ARM: pxa: ssp: provide platform_device_id for PXA3xx
ARM: OMAP4+: Remove static iotable mappings for SRAM
ARM: OMAP4+: Move SRAM data to DT
...
This time around, the cleanup branch contains mostly code removal. A number
of board files for at91, imx and msm have become obsolete because of the
DT conversion and are now ready to be removed. The OMAP platform has
traditionally had its own DMA engine abstraction and as this is being
phased out, a lot of the original code is now unused and can be removed
as well.
S3C24xx can be simplified now that the restart code is a proper device
driver.
Finally, a number of cleanups in shmobile are done to prepare for
the addition of new code in other branches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Af7T
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"This time around, the cleanup branch contains mostly code removal. A
number of board files for at91, imx and msm have become obsolete
because of the DT conversion and are now ready to be removed. The
OMAP platform has traditionally had its own DMA engine abstraction and
as this is being phased out, a lot of the original code is now unused
and can be removed as well.
S3C24xx can be simplified now that the restart code is a proper device
driver.
Finally, a number of cleanups in shmobile are done to prepare for the
addition of new code in other branches"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91: Remove the support for the RSI EWS board
arm: mach-omap2: Convert pr_warning to pr_warn
ARM: OMAP: Remove unused pieces of legacy DMA API
ARM: at91: remove board file for Acme Systems Fox G20
ARM: orion5x: Convert pr_warning to pr_warn
ARM: S3C24XX: remove separate restart code
ARM: EXYNOS: Do not calculate boot address twice
ARM: sunxi: Remove sun4i reboot code from mach directory
ARM: imx: Remove mach-mxt_td60 board file
ARM: shmobile: armadillo800eva legacy: Use rmobile_add_devices_to_domains()
ARM: shmobile: r8a7740: Clean up pm domain table
ARM: shmobile: r8a7740: Use rmobile_add_devices_to_domains()
ARM: shmobile: sh7372: Make domain_devices[] static __initdata
ARM: shmobile: mackerel: Make domain_devices[] static __initdata
clocksource: tcb_clksrc: sanitize IRQ request
ARM: at91/tclib: mask interruptions at shutdown and probe
ARM: at91/tclib: move initialization from alloc to probe
ARM: at91/tclib: prefer using of devm_* functions
ARM: clps711x: Switch CLPS711X subarch to use clk and clocksource driver
ARM: shmobile: r8a7791 is now called "R-Car M2-W"
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others,
as well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Smzi
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others, as
well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: update Shawn's email address
MAINTAINERS: condense some Tegra related entries
MAINTAINERS: add Alexandre Courbot for Tegra
MAINTAINERS: CNS3xxx and IXP4xx update.
MAINTAINERS: Add maintainers entry for Mediatek SoCs
arm, vt8500, LLVMLlinux: Use mcr instead of mcr% for mach-vt8500
MAINTAINERS: add a third maintainer to mach-bcm
CNS3xxx: Fix PCIe read size limit.
CNS3xxx: Fix logical PCIe topology.
CNS3xxx: Fix debug UART.
MAINTAINERS: Add entry for the Amlogic MesonX SoCs
MAINTAINERS: update ARM pxa maintainers
ARM: at91/PMC: don't forget to write PMC_PCDR register to disable clocks
ARM: at91: fix at91sam9263ek DT mmc pinmuxing settings
ARM: mvebu: Netgear RN102: Use Hardware BCH ECC
ARM: Kirkwood: Fix DT based DSA.
ARM: OMAP2+: make of_device_ids const
ARM: omap2: make arrays containing machine compatible strings const
ARM: LPC32xx: Fix reset function
ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
...
No need to store netlbl_unlabel_genl_init result and test it before returning.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two helpers so that drivers do not have to care of BQL being
available or not.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jim Davis <jim.epost@gmail.com>
Fixes: 29d40c9032 ("net/mlx4_en: Use prefetch in tx path")
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 7bced39751,
dma_cookie was removed from struct skbuff.
But the description of dma_cookie still exist.
So the "make xmldocs" output following warning.
Warning(.//include/linux/skbuff.h:609): Excess struct/union
/enum/typedef member 'dma_cookie' description in 'sk_buff'
Remove description of dma_cookie fix the symptom.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_desc struct holds 8 __be64 values. The original code in
ring_tx_db() took a tx_desc pointer then casted it to an int pointer and
then casted it to a u64 pointer. It was confusing and triggered some
static checker warnings.
I have changed the cxgb_pio_copy() function to only take tx_desc
pointers. This isn't really a loss of flexibility because anything else
was buggy to begin with.
I also removed the casting on the destination pointer since that was
unnecessary and a bit messy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"cntxt_id" is an unsigned int but "udb" is a u64 so there is a potential
shift wrapping bug here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support skb->xmit_more in i40e is straightforward : we need to move
around i40e_maybe_stop_tx() call to correctly test netif_xmit_stopped()
before taking the decision to not kick the NIC.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe Leroy says:
====================
net: fs_enet: Remove non NAPI RX and add NAPI for TX
When using a MPC8xx as a router, 'perf' shows a significant time spent in
fs_enet_interrupt() and fs_enet_start_xmit().
'perf annotate' shows that the time spent in fs_enet_start_xmit is indeed spent
between spin_unlock_irqrestore() and the following instruction, hence in
interrupt handling. This is due to the TX complete interrupt that fires after
each transmitted packet.
This patchset first remove all non NAPI handling as NAPI has become the only
mode for RX, then adds NAPI for handling TX complete.
This improves NAT TCP throughput by 21% on MPC885 with FEC.
Tested on MPC885 with FEC.
[PATCH 1/2] net: fs_enet: Remove non NAPI RX
[PATCH 2/2] net: fs_enet: Add NAPI TX
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a MPC8xx as a router, 'perf' shows a significant time spent in
fs_enet_interrupt() and fs_enet_start_xmit().
'perf annotate' shows that the time spent in fs_enet_start_xmit is indeed spent
between spin_unlock_irqrestore() and the following instruction, hence in
interrupt handling. This is due to the TX complete interrupt that fires after
each transmitted packet.
This patch modifies the handling of TX complete to use NAPI.
With this patch, my NAT router offers a throughput improved by 21%
Original performance:
[root@localhost tmp]# scp toto pgs:/tmp
toto 100% 256MB 2.8MB/s 01:31
Performance with the patch:
[root@localhost tmp]# scp toto pgs:/tmp
toto 100% 256MB 3.4MB/s 01:16
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the probe function, use_napi is inconditionnaly set to 1. This patch removes
all the code which is conditional to !use_napi, and removes use_napi which has
then become useless.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8168EP is Realtek PCIe Gigabit Ethernet controller with DASH support.
It is a successor chip of RTL8168DP.
For RTL8168EP, the read/write ocp register is via eri channel type 2, so I
move ocp_xxx() related functions under rtl_eri_xxx. And use r8168dp_ocp_xxx()
for RTL8168DP ocp read/write, r8168ep_ocp_xxx() for RTL8168EP ocp read/write.
The way of checking dash enable is different with RTL8168DP. I use
r8168dp_check_dash()for RTL8168DP and r8168ep_check_dash() for RTL8168EP,
to check if dash is enabled.
The driver_start() and driver_stop() of RTL8168EP is also different with
RTL8168DP. I use rtl8168dp_driver_xxx() for RTL8168DP and
rtl8168ep_driver_xxx for RTL8168EP.
Right now, RTL8168EP phy mcu did not need firmware code patch, so I did not
add firmware code for it.
so I did not add firmware code for it.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to copy exts->type when committing the change, otherwise
it would be always 0. This is a quick fix for -net and -stable,
for net-next tcf_exts will be removed.
Fixes: commit 33be627159 ("net_sched: act: use standard struct list_head")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because CCN's cycle counter always runs, it will generate
an interrupt on overflow even if the relevant perf event
was not requested, causing a spurious warning message.
Fixed now by warning on only normal counter unwanted
overflows. Also cleaning the overflow mask at init now,
not to warn on event previously requested by firmware.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
My Freescale email address will be gone shortly. Update my email to be
the Linaro one.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There's little point having specific entries in MAINTAINERS for Tegra
drivers that are already covered by the top-level Tegra architecture
support entry, and maintained by people listed there. Remove the
duplicates.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I'd like to propose Alexandre Courbot as an additional Tegra maintainer.
He's been working on a variety of Tegra-related code for a while, and
is now officially tasked with working on upstream support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
--
v2:
* Use Alexandre's full name.
* Use a non-NVIDIA email address to avoid Exchange Server patch corruption.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Meson6 WDT support" from Carlo Caione:
This patch adds the support for the Meson6 watchdog in the DTSI
* tag 'meson-wdt-dt-3.18' of https://github.com/carlocaione/linux-meson:
ARM: DTS: meson: update DTSI to add watchdog node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull f2fs updates from Jaegeuk Kim:
"This patch-set introduces a couple of new features such as large
sector size, FITRIM, and atomic/volatile writes.
Several patches enhance power-off recovery and checkpoint routines.
The fsck.f2fs starts to support fixing corrupted partitions with
recovery hints provided by this patch-set.
Summary:
- retain some recovery information for fsck.f2fs
- enhance checkpoint speed
- enhance flush command management
- bug fix for lseek
- tune in-place-update policies
- enhance roll-forward speed
- revisit all the roll-forward and fsync rules
- support larget sector size
- support FITRIM
- support atomic and volatile writes
And several clean-ups and bug fixes are included"
* tag 'f2fs-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (42 commits)
f2fs: support volatile operations for transient data
f2fs: support atomic writes
f2fs: remove unused return value
f2fs: clean up f2fs_ioctl functions
f2fs: potential shift wrapping buf in f2fs_trim_fs()
f2fs: call f2fs_unlock_op after error was handled
f2fs: check the use of macros on block counts and addresses
f2fs: refactor flush_nat_entries to remove costly reorganizing ops
f2fs: introduce FITRIM in f2fs_ioctl
f2fs: introduce cp_control structure
f2fs: use more free segments until SSR is activated
f2fs: change the ipu_policy option to enable combinations
f2fs: fix to search whole dirty segmap when get_victim
f2fs: fix to clean previous mount option when remount_fs
f2fs: skip punching hole in special condition
f2fs: support large sector size
f2fs: fix to truncate blocks past EOF in ->setattr
f2fs: update i_size when __allocate_data_block
f2fs: use MAX_BIO_BLOCKS(sbi)
f2fs: remove redundant operation during roll-forward recovery
...
