Use the same naming convention for DMA traffic MMRs (most were legacy
anyways) so we can avoid useless ifdef trees.
Same goes for MDMA names -- this actually allows us to undo a bunch of
ifdef redirects that existed for this purpose alone.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
A bunch of arches define reads[bwl]/writes[bwl] helpers for accessing
memory mapped registers. Since the Blackfin ones aren't specific to
Blackfin code, move them to the common asm-generic/io.h for people.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Each Blackfin port has been duplicating UART structures and defines when
there really is no need for it. So start a new bfin_serial.h header to
unify all these pieces and give ourselves a fresh start.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In order to not touch the driver file for different xtal usage,
push the clkin value to board file and calculate the register
value instead of hardcoding it.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
Just adding its own platform_driver, not really
using it yet.
Later patches will come to split power management
code from musb_core and move it completely to HW
glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Soon resource data will get automatically
populated from a set of autogenerated data
from TI's hardware database for the OMAP
platform.
Such database, might not have resources at
the expected order by the current drivers.
While we could hack in some exceptions to
that tool to generate resources in a specific
order, it seems less fragile to use the
resource name instead. That way, no matter
what order the resources are generated, the
driver still work.
Modified the OMAP, Blackfin and Davinci
architecture files to add the name of the IRQs
in the resource structures and musb driver to
use the platform_get_irq_byname() api to get
the device and dma irq numbers instead of using
the index.
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a partial revert of b595076a ("tree-wide: fix comment/printk
typos"), as blackfin tree is going to have completely different
version of the code.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The kgdb_disable_hw_debug() was an architecture specific function for
disabling all hardware breakpoints on a per cpu basis when entering
the debug core.
This patch will remove the weak function kdbg_disable_hw_debug() and
change it into a call back which lives with the rest of hw breakpoint
call backs in struct kgdb_arch.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (38 commits)
kbuild: convert `arch/tile' to the kconfig mainmenu upgrade
README: cite nconfig
Revert "kconfig: Temporarily disable dependency warnings"
kconfig: Use PATH_MAX instead of 128 for path buffer sizes.
kconfig: Fix realloc usage()
kconfig: Propagate const
kconfig: Don't go out from read config loop when you read new symbol
kconfig: fix menuconfig on debian lenny
kbuild: migrate all arch to the kconfig mainmenu upgrade
kconfig: expand file names
kconfig: use the file's name of sourced file
kconfig: constify file name
kconfig: don't emit warning upon rootmenu's prompt redefinition
kconfig: replace KERNELVERSION usage by the mainmenu's prompt
kconfig: delay gconf window initialization
kconfig: expand by default the rootmenu's prompt
kconfig: add a symbol string expansion helper
kconfig: regen parser
kconfig: implement the `mainmenu' directive
kconfig: allow PACKAGE to be defined on the compiler's command-line
...
Fix up trivial conflict in arch/mn10300/Kconfig
Change signature of get/put_reg() according to the change of arch_ptrace()
and remove unnecessary castings.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the arguments to arch_ptrace() to take account of the fact that
@addr and @data are now unsigned long rather than long as of a preceding
patch in this series.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Long ago, PT_TRACESYS_OFF and friends were introduced as hard defines to
avoid straight constants in assembler parts of linux m68k. They are not
used anymore, and were not updated to follow changes in linux kernel.
Remove them. When similar constants are needed, they are now generated
using asm-offsets.c.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No one uses these MMRs so we didn't notice when the anomaly handling
logic was inverted.
Reported-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This code was useful during early port development when our icache code
wasn't solid, but that ship has sailed long ago, and no code calls this
function anymore (irq_panic). So punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
- enable pm for ADI boards
- drop security option as no one uses it
- enable uninitialized mmap for everyone
- disable wireless by default as no one uses it
- disable cfq io sched as noop is fine
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Move all the pin settings out of the Kconfig and into the platform
resources (MII vs RMII). This clean up also lets us push out the
phy settings so that board porters may control the layout.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Start unifying the PPI/EPPI peripheral structures in one place. This
may be used by camera/video/fpga/high speed devices.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This matches all the other Blackfin ports and keep us from having to write
bf561-specific code in many places.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the common 8250 serial driver supports an "irqflags" field,
we don't need to patch in a custom define into the code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Different arches use different names, so make sure we define both so
common code (like MTD_XIP) "just works".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mainline version of git merged support for Blackfin parts, but we now
need to propagate the gcc arch define to make it work.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We have to use ioctl numbers that don't collide with common code.
Otherwise, these ones never even get called because the common fs
code swalled all invocations.
Reported-by: Kay Duenzer <kduenzer@maku.eu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This board has a SSM2603 codec, so make sure we have the right resources
declared for it.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The RX/TX address is always the same regardless of the size of the access.
That means there is no dedicated "16bit" or "32bit" MMR. Trying to use
these currently leads to compile errors. So change everything to use the
right MMR define.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
Since these boards can boot out of NAND, make sure we give u-boot its
own partition by default to avoid clobbering it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the kernel's init section is merged back into the main memory region
during boot (which it should since that is how we've laid out the kernel
linker map), we want to make sure that these aren't counted as independent
regions. Otherwise, if a large mapping is attempted which starts in the
init region and extends into the main memory region, the access_ok func
will deny it. This leads to weird messages during runtime like "unable
to map xxx library" from the ldso but upon running the application again,
everything works fine.
So if the address of the end of the init region is the same as the start
of the main memory region, simply enlarge the memory region to include
the init region.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many Blackfin parts group sets of pins into a single functional unit.
This means you cannot use different pins within a group for different
peripherals. Our resource conflict checking thus far has been limited
to individual pins, so if someone tried to grab a different pin from
the same group, it would be allowed while silently changing the other
pins in the same group.
One common example is the pin set PG12 - PG15 on BF51x parts. They
may either be used with SPI0 (1st function), or they may be used with
PTP/PWM/AMS3 (3rd function). Ideally, we'd like to use PG12 - PG14
for SPI0 while using PG15 with AMS3, but the hardware does not permit
this. In the past, the software would allow the pins to be requested
this way, but ultimately things like the Blackfin SPI driver would
stop working when the hardware rerouted to a different peripheral.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Flushing caches sometimes requires anomaly workarounds which require
supervisor-only insns. Normally we don't need to flush caches from
userspace so this isn't a problem, but when gcc generates trampolines
on the stack, we do.
So add a new syscall for gcc to use modeled after the mips version.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF54x processor has a ton of on-chip peripherals and in order to
support them all, the u-boot image is quite large. So give it 512KiB
in all bootable flashes to make our lives easier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we include EMAC_SYSTAT when showing errors.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The predefined i2c address 0x2c doesn't match the configuration of the
ad5280 PINs AD0 and AD1 on the tftlcd add-on board. Both AD0 and AD1
are of voltage 3.3V, which means the i2c address should be 0x2F.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Nothing actually needs to use these MMRs (as direct cache manipulation
is done with the DTEST MMRs), so simply hide the read funcs behind the
anomaly define. They're generally unusable anyways when this anomaly
is in effect.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When apps run with their stack in L1, some system calls might be made
where a buffer is in the stack as an argument. So make sure the core
Blackfin access code does not reject this memory location.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This board has an AD1836 codec, so make sure we have the right resources
declared for it.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If an app is placing its stack in L1 scratchpad SRAM, make sure ptrace
is granted access to it so that gdb can do its thing.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The num_chipselect field for on-chip Blackfin SPI buses is supposed to
be 1 larger than the number of actual CSs available. This is because
the hardware starts counting at 1 and not 0. There is a field for "CS0",
but it is marked as "reserved" everywhere.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't need our own header and structure to hook up the ad5398 part,
so drop the custom resources for it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than write our own ADP switch driver, use the existing fixed
regulator driver and rewrite the platform resources accordingly.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some peripherals might generate an error interrupt shortly after the
data interrupt due to the fact that the peripheral isn't serviced fast
enough. In most cases this isn't a problem and is expected behavior.
This hasn't been a problem on most parts since you simply don't request
the error interrupt (or you leave it disabled while there is an expected
state) and do the peripheral status checking in the data interrupt.
The Blackfin SIC allows people to prioritize data and error interrupts,
and the Blackfin CEC allows interrupts of equal or higher priority to
nest. The current default settings gives error interrupts a higher
priority than data interrupts. So if an error occurs while processing
the data interrupt, it will be serviced immediately.
However, the error interrupt on the BF537 SIC cannot be enabled on a
per-peripheral basis. Once the error interrupt is enabled for one
peripheral, it is automatically enabled for all peripherals.
Therefore lower the default multiplexed error interrupt priority so
most people need not worry themselves with this issue.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
With the recent kernel update the isp1362-hcd driver evaluates the
IORESOURCE_IRQ resource flags and requests the irq with the given
polarity/edge settings. However the ISP1362 config requires low
level/edge interrupts. Most of the Blackfin boards use some random
flag or no flag at all. Make all boards use a know good flag
IORESOURCE_IRQ_LOWEDGE.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The NAND platform driver expects the registers to have a "mem"
resource type rather than "io".
Signed-off-by: Valentin Yakovenkov <yakovenkov@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add platform resources for the on-chip CAN peripheral so we can use it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we use the right Kconfig names and platform strings.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that we've rewritten the GPIO CS handling in the Blackfin SPI
peripheral, we need to update the platform resources accordingly.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the common header defines everything and the SPI drivers are
using it, we can drop these duplicated global namespace polluters.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
While combining things, also switch to the proper SPI bit define names.
This lets us punt the rarely used SPI defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The common SPI layers take care of detecting CS conflicts and preventing
two devices from claiming the same CS. This causes problems for the GPIO
CS support we currently have as we are using CS0 to mean "GPIO CS". But
if we have multiple devices using a GPIO CS, the common SPI layers see
multiple devices using the virtual "CS0" and reject any such attempts.
To make both work, we introduce an offset define. This represents the
max number of hardware CS values that the SPI peripheral supports. If
the CS is below this limit, we know we can use the hardware CS. If it's
above, we treat it as a GPIO CS. This keeps the CS unique as seen by
the common code and prevents conflicts.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Expand the BIT_CTL defines to use the naming convention of the hardware,
and expand the masks to cover all documented bits.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
As David points out, the cs_change_per_word option isn't standard, nor is
anyone actually using it. So punt all of the dead code considering it
makes up ~10% of the code size.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
Rename h/w IRQ flags handling functions to be in line with what is expected for
the irq renaming patch. This renames local_*_hw() to hard_local_*() using the
following perl command:
perl -pi -e 's/local_irq_(restore|enable|disable)_hw/hard_local_irq_\1/ or s/local_irq_save_hw([_a-z]*)[(]flags[)]/flags = hard_local_irq_save\1()/' `find arch/blackfin/ -name "*.[ch]"`
and then fixing up asm/irqflags.h manually.
Additionally, arch/hard_local_save_flags() and arch/hard_local_irq_save() both
return the flags rather than passing it through the argument list.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a missing dependency (mach/blackfin.h) to asm/irqflags.h so that
bfin_read_IMASK() can be used by inline functions.
Signed-off-by: David Howells <dhowells@redhat.com>
Split the BF532 machine type BFIN_*_FIO_FLAG() functions to their own header
file to avoid circular #include problems as these functions require IRQ flag
handling, which requires asm/blackfin.h, which otherwise requires the header
file that defines these functions.
For good measure, also get rid of the inclusion of asm/blackfin.h from
mach/cdefBF532.h (which is circular) and defBF532.h (which is included by
asm/blackfin.h before including this header).
Signed-off-by: David Howells <dhowells@redhat.com>
Split the PLL control code from the Blackfin machine-specific cdef headers so
that the irqflags functions can be renamed without incurring a header loop.
Signed-off-by: David Howells <dhowells@redhat.com>
Now that the driver for the Blackfin on-chip NFC no longer uses/respects
the page_size from the platform resources (figures out the needs on the
fly), drop it from the platform resources. This fixes some build errors
since the defines no longer exists.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The common bfin_sport.h header now has unified definitions of these, so
stop polluting the global namespace.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The recent commit to add constant optimization to hweight implicitly broke
the Blackfin arch. Seems we were missed when all the other arches were
fixed with renames.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:
arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type
This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to. This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel(). A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().
do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.
Further kernel_execve() and sys_execve() need to be changed to match.
This has been test built on x86_64, frv, arm and mips.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6:
mtd/nand_ids: Fix buswidth
mtd/m25p80: fix test for end of loop
mtd/m25p80: retlen is never NULL
MIPS: Fix gen_nand probe structures contents
gen_nand: Test if nr_chips field is valid
BFIN: Fix gen_nand probe structures contents
nand/denali: move all hardware initialization work to denali_hw_init
nand/denali: Add a page check in denali_read_page & denali_read_page_raw
nand/denali: use cpu_relax() while waiting for hardware interrupt
nand/denali: change read_status function method
nand/denali: Fixed check patch warnings
ARM: Fix gen_nand probe structures contents
mtd/nand_base: fix kernel-doc warnings & typos
nand/denali: use dev_xx debug function to replace nand_dbg_print and some printk
nand/denali: Fixed handle ECC error bugs
nand/denali: use iowrite32() to replace denali_write32()
nand/denali: Fixed probe function bugs
