Commit 6aa85a5ae6 (omap4: 4430sdp:
enable the ehci port on 4430SDP) added code to enable EHCI
support on 4430sdp board.
Looks like the ULPI pin does not seem to be muxed properly on ES1.0
SDP and this causes the system to reboot when the ULPI PHY is
enabled.
Fix this by muxing the pin, this is the same setting for
both ES1.0 and ES2.0. Also add checking for gpio_request.
Cc: Keshava Munegowda <keshava_mgowda@ti.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch is adding support for pwm1 and pwm2 devices found
on mx51.
[ this patch has been tested with pwm-backlight driver ]
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 076762aa52 is adding a macro whis is
calling imx_add_mxc_pwm() but gives it 2 parameters while it's taking only
one parameters.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Card Detect GPIOs used on AP4EVB and Mackerel are
alwayws valid, so kill off the unused !gpio_is_valid()
case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support System MMU for S5PV310 and S5PC210.
Signed-off-by: Donguk Ryu <du.ryu@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: changed SYSMMU config name]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support System MMU which supports address transition
from virtual address to physical address. Basically, each hardware
block is connected System MMU block can use directly vitrual address
when it accesses physical memory not using physical address.
Signed-off-by: Donguk Ryu <du.ryu@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: removed useless codes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The kerneldoc for this function is at odds with the DMA-API
document, which holds, so fix it.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To make mc13783 and mc13892 share code, the register names should be
changed to fit the new macro definitions in the comming patch.
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The ab8500 regulator board configuration is updated and put in an
array which can easily be used in the MFD board configuration. The
regulator board configuration is also added to the MFD
configuration in this patch.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The CLZ instruction does not alter the condition flags, so remove the
"cc" clobber from the inline asm for fls().
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_CMDLINE_FORCE is used, the warning
Ignoring unrecognised tag 0x54410009
was displayed. Change this to
Ignoring tag cmdline (using the default kernel command line)
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for dynamical allocation of imx-keypad on mx5 platform.
After moving to dynamically registration of the keypad, the keypad clock
name needs to change accordingly.
The reason is that the original mx5 keypad platform_device id was 0,
now we use id=-1 as per arch/arm/plat-mxc/devices/platform-imx-keypad.c.
Tested keypad successfully on a MX51_3DS board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mxs duart is actually an amba-pl011 device. This commit changes
the duart device code to dynamically allocate amba-pl011 device,
so that drivers/serial/amba-pl011.c can be used on mxs.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch enables interrupt generation for SDIO IRQs
of the SDHI block on the sh7377 aka G4 processor. Use
together with a recent SDHI driver using TMIO_MMC_SDIO_IRQ
and with the MMC_CAP_SDIO_IRQ flag in the board code.
The G4EVM specific SDHI platform data is also updated to
flag SDIO capabilities.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables interrupt generation for SDIO IRQs
of the SDHI block on the sh7367 aka G3 processor. Use
together with a recent SDHI driver using TMIO_MMC_SDIO_IRQ
and with the MMC_CAP_SDIO_IRQ flag in the board code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the interrupt generation for SDIO IRQs
of the sdhi controllers of the SoC. To make sure interrupts
are handled announce the MMC_CAP_SDIO_IRQ capability
on AP4EVB. Tested with a b43-based SDIO wireless card.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for clock information exposed to debug-fs interface.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[kgene.kim@samsung.com: removed useless empty lines]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
TFP410 DVI chip is used to provide display out.
This chip is controlled by 2 lines:
LDO which supplies the power is controlled over gpio + 2
and the enable of the chip itself is done over gpio + 1
NOTE: the LDO is necessary for LED, serial blocks as well.
gpio + 1 was used to sense USB overcurrent in vanilla beagle.
Without this fix, the display would not function as the LDO
remains shut down.
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_reserve functionality to board-igep0030.c.
This patch is in similar lines to commit id 71ee7dad9b, from
Russell king
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO reset line for Beagle XM is different from vanilla beagle
so we populate it as part of gpio update routine.
This in part fixes the issue of display not functioning on beagle XM
platform.
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHCI enable power pin is inverted (active high) in comparison
to vanilla beagle which is active low. Handle this case conditionally.
Without this fix, Beagle XM 4 port EHCI will not function and no
networking will be available
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When running without an MMU, we do not need to install a mapping for the
vectors page. Attempting to do so causes a compile-time error because
install_special_mapping is not defined.
This patch adds compile-time guards to the vector mapping functions
so that we can build nommu configurations once more.
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The purpose of the minsec argument is to prevent 64-bit math overflow
when the number of cycles is multiplied up. However, the multipler
is 32-bit, and in the sched_clock() case, the cycle counter is up to
32-bit as well. So the math can never overflow.
With a value of 60, and clock rates greater than 71MHz, the calculated
multiplier is unnecessarily reduced in value, which reduces accuracy by
maybe 70ppt. It's almost not worth bothering with as the oscillator
driving the counter won't be any more than 1ppm - unless you're using
a rubidium lamp or caesium fountain frequency standard.
So, set the minsec argument to zero.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sched_clock is supposed to be initialized early - in the recently added
init_early platform hook. However, in doing so we end up calling
mod_timer() before the timer lists are initialized, resulting in an
oops.
Split the initialization in two - the part which the platform calls
early which starts things off. The addition of the timer can be
delayed until after we have more of the kernel initialized - when the
normal time sources are initialized.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/arm/mach-integrator/cpu.c: In function ■integrator_get■:
arch/arm/mach-integrator/cpu.c:164: warning: ■vco.s■ may be used uninitialized in this function
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change device name from "fec" to "imx28-fec", so that fec driver
can distinguish mx28.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fraction of MHz was not being displayed correctly as the calculation
was a factor of 10 out. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialise the SCIF serial port to allow earlyprintk
output when using zboot.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initialise the SCIF serial port to allow earlyprintk
output when using zboot. It is based on a very similar
patched for AP4EB.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We perform the microseconds to loops calculation using a number of
multiplies and shift rights. Each shift right rounds down the
resulting value, which can result in delays shorter than requested.
Ensure that we always round up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ux500: allow 5500 and 8500 to be built together
ux500: modem_irq is only for 5500
ux500: dynamic SOC detection
ux500: rename MOP board Kconfig
ux500: remove build-time changing macros
* 'msm-smp' of git://codeaurora.org/quic/kernel/davidb/linux-msm:
msm: add SMP support for msm
msm: hotplug: support cpu hotplug on msm
msm: timer: SMP timer support for msm
msm: scm-boot: Support for setting cold/warm boot addresses
msm: Secure Channel Manager (SCM) support
Support twl4030 keypad and gpio keys on IGEP v2.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second MMC channel (used by the WLAN/BT module) is not linked to
power regulator. This causes the WLAN/BT module to fail being detected if
CONFIG_REGULATOR_DUMMY is not set.
This patch adds the two regulators that actually feed the WLAN/BT module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 IGEP module has one EHCI interface on board using
USB2HS port. GPIO183 is used as PHY reset.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At latest mainline commit 0c21e3aaf6, omap2plus build is broken. This
patch is trivial fix for the missed usb clock node for CK_3430ES2PLUS
flag update.
CHK include/generated/compile.h
CC arch/arm/mach-omap2/clock3xxx_data.o
arch/arm/mach-omap2/clock3xxx_data.c:3289: error: 'CK_3430ES2' undeclared
here (not in a function)
make[1]: *** [arch/arm/mach-omap2/clock3xxx_data.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated mask to include CK_36XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SMSC 3320 USB PHY on the OMAP4 Pandaboard needs a 19.2 MHz
reference clock. This clock is provided from the OMAP4's fref_clk3
pad.
Recent changes to clock44xx_data.c made the clock framework aware
of the existence of these fref_clk[i] lines. If the option
CONFIG_OMAP_RESET_CLOCKS is enabled in the kernel, then the
clock framework will turn these clocks off during bootup.
Explicitly request and keep this clock enabled at init for the
Pandaboard, so that the PHY receives this clock at all times.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Modified to hit the right file]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Dynamically detect the DBx500 SOC an revision based on the ASIC ID.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the MOP board Kconfig entries to the same name as the machine
type, so that the machine_is_*() macros work correctly.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Updated to match changes in the tree]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
To allow the possiblity of building U8500 and U5500 support in the same
image.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Rebased to latest changes in Russells tree]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A panel connects to one of the overlay managers of DSS through some interface block.
On OMAP4, specifying the type of the display is not sufficient to conclude which manager
the panel should be connected to.
Hence, a new member 'channel' is introduced in omap_dss_device structure to determine
which manager the panel uses. The dss_recheck_connections() called in dss_driver_probe()
uses this channel parameter to set the correct manager to the corresponding omap_dss_device.
The channel parameter is used only once to ensure the correct managers are set for each
panel. The parameter dssdev->manager->id will take care of ensuring that the panel and
then the interface driver configures the correct DISPC channel.
Also, add a new Overlay Manager in manager.c, make other changes needed for LCD2 channel.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
DISPC functions are modified in order to work when the manager is LCD2.
This includes:
Adding new IRQs specific to LCD2 and their handling.
Provide dumps of the new manager's registers.
Provide dumps of the new manager's clocks.
Checks for channel for registers DISPC_CONTROL2 and DISPC_CONFIG2
which can't be parametrized.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
On OMAP4, we have a new DISPC channel for Overlay Manager LCD2. There is a set
of regsiters for LCD2 channel similar to the existing LCD channel, like
DISPC_CONTROL2, DISPC_DIVISOR2, DISPC_CONFIG2 and so on.
Introduce new enum members for LCD2 Channel and corresponding Overlay Manager
in display.h.
Represent the following DISPC register defines with channel as a parameter
to differentiate between LCD and LCD2 registers (and also DIGIT in some cases):
DISPC_DEFAULT_COLOR, DISPC_TRANS_COLOR, DISPC_TIMING_H, DISPC_TIMING_V,
DISPC_POL_FREQ, DISPC_DIVISOR, DISPC_SIZE_LCD, DISPC_DATA_CYCLEk,
DISPC_CPR_COEF_R, DISPC_CPR_COEF_G and DISPC_CPR_COEF_B
This parametrization helps in reducing the number of register defines for DISPC.
Replace the existing reads/writes to these registers in this new way.
Also, Introduce defines for registers DISPC_CONTROL2 and DISPC_CONFIG2 which
are used exclusively for LCD2 channel.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Still keep sharp_ls_panel, since the sharp_ls_panel driver contains blacklight
control driver code which will be moved out later. Then we can use generic DPI
driver for sharp_ls_panel.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Generic DPI panel driver includes the driver and 4 similar panel configurations. It
will match the panel name which is passed from platform data and setup the
right configurations.
With generic DPI panel driver, we can remove those 4 duplicated panel display
drivers. In the future, it is simple for us just add new panel configuration
date in panel-generic-dpi.c to support new display panel.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Board-zoom-display.c added as a common file for display functionality
on boards zoom2, zoom3 and 3630sdp.
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Kishore Y <kishore.y@ti.com>
Signed-off-by: Rajkumar N <rajkumar.nagarajan@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Enable dss to process color formats with pre-mulitplied alpha.
With this we can have alpha values defined for each pixel
and hence can have different blending values for each pixel.
sysfs entry has been created for this and pre-multiplied alpha
support is turned off by default.
Signed-off-by: Sudeep Basavaraj <sudeep.basavaraj@ti.com>
Signed-off-by: Rajkumar N <rajkumar.nagarajan@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
SDHCI driver for Tegra. This driver plugs in as a new variant of
sdhci-pltfm, using the platform data structure passed in to specify the
GPIOs to use for card detect, write protect and card power enablement.
Original driver (of which only the header file is left):
Signed-off-by: Yvonne Yip <y@palm.com>
The rest, which has been rewritten by now:
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
The msm provides timer hardware that is private to each core. Each
timer has separate counter and match registers, so we create separate
clock_event_devices for each core. For the global clocksource, use
cpu 0's counter.
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add support for setting the cold boot address of core 1 and
the warm boot addresses of cores 0 and 1 using a secure
domain call.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
SCM is the protocol used to communicate between the secure and
non-secure code executing on the applications processor. The
non-secure side uses a physically contiguous buffer to pass
information to the secure side; where the buffer conforms to a
format that is agreed upon by both sides. The use of a buffer
allows multiple pending requests to be in flight on the secure
side. It also benefits use cases where the command or response
buffer contains large chunks of data.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
* 'rmobile-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (67 commits)
ARM: mach-shmobile: update for SMP changes.
ARM: mach-shmobile: update for GIC changes.
ARM: mach-shmobile: Fix up clkdev fallout for SH73A0.
dma: shdma: don't register the global die notifier multiple times
ARM: mach-shmobile: Rely on run-time IRQ handlers
ARM: mach-shmobile: Run-time IRQ handler for GIC
ARM: mach-shmobile: Run-time IRQ handler for INTCA
ARM: mach-shmobile: Enable CONFIG_MULTI_IRQ_HANDLER
ARM: mach-shmobile: Use shared GIC entry macros
ARM: mach-shmobile: mackerel: Add zboot support
ARM: mach-shmobile: mackerel: Add HDMI sound support
ARM: mach-shmobile: mackerel: add HDMI video support
ARM: mach-shmobile: ap4evb: fixup clk_put timing of fsib_clk
ARM: mach-shmobile: sh73a0: fix div4 table
ARM: mach-shmobile: ap4/mackerel: modify wrong comment out of USB
ARM: mach-shmobile: Mackerel VGA camera support
mmc: sh_mmcif: make DMA support by the driver unconditional
ARM: mach-shmobile: Add eMMC support through MMCIF on AG5EVM
ARM: mach-shmobile: Use pullups for AG5EVM KEYSC pins
ARM: mach-shmobile: sh73a0 GPIO pullup improvement
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (58 commits)
Input: wacom_w8001 - support pen or touch only devices
Input: wacom_w8001 - use __set_bit to set keybits
Input: bu21013_ts - fix misuse of logical operation in place of bitop
Input: i8042 - add Acer Aspire 5100 to the Dritek list
Input: wacom - add support for digitizer in Lenovo W700
Input: psmouse - disable the synaptics extension on OLPC machines
Input: psmouse - fix up Synaptics comment
Input: synaptics - ignore bogus mt packet
Input: synaptics - add multi-finger and semi-mt support
Input: synaptics - report clickpad property
input: mt: Document interface updates
Input: fix double equality sign in uevent
Input: introduce device properties
hid: egalax: Add support for Wetab (726b)
Input: include MT library as source for kerneldoc
MAINTAINERS: Update input-mt entry
hid: egalax: Add support for Samsung NB30 netbook
hid: egalax: Document the new devices in Kconfig
hid: egalax: Add support for Wetab
hid: egalax: Convert to MT slots
...
Fixed up trivial conflict in drivers/input/keyboard/Kconfig
omap2plus_defocnfig build breaks when customised with only ARCH_OMAP4
selected. This is because common files make references to the functions
which are defined only for omap2xxx and omap3xxx.
LD .tmp_vmlinux1
arch/arm/mach-omap2/built-in.o: In function `pm_dbg_regset_store':
arch/arm/mach-omap2/pm-debug.c:335: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `omap2_pm_dump':
arch/arm/mach-omap2/pm-debug.c:121: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/pm-debug.c:123: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/pm-debug.c:124: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/pm-debug.c:125: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `omap_prcm_arch_reset':
arch/arm/mach-omap2/prcm.c:106: undefined reference to `omap2_prm_set_mod_reg_bits'
arch/arm/mach-omap2/prcm.c:108: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `omap_prcm_get_reset_sources':
arch/arm/mach-omap2/prcm.c:53: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `clkdm_clear_all_wkdeps':
arch/arm/mach-omap2/clockdomain.c:545: undefined reference to `omap2_prm_clear_mod_reg_bits'
arch/arm/mach-omap2/built-in.o: In function `clkdm_del_wkdep':
arch/arm/mach-omap2/clockdomain.c:475: undefined reference to `omap2_prm_clear_mod_reg_bits'
arch/arm/mach-omap2/built-in.o: In function `clkdm_read_wkdep':
arch/arm/mach-omap2/clockdomain.c:511: undefined reference to `omap2_prm_read_mod_bits_shift'
arch/arm/mach-omap2/built-in.o: In function `clkdm_add_wkdep':
arch/arm/mach-omap2/clockdomain.c:440: undefined reference to `omap2_prm_set_mod_reg_bits'
make: *** [.tmp_vmlinux1] Error 1
This patch adds stubs for these functions so that build continues to work.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
CC arch/arm/mach-omap2/omap_hwmod_common_data.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/omap_hwmod_common_data.c:20:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_late_init':
arch/arm/plat-omap/include/plat/voltage.h:145: error: 'EINVAL' undeclared (first use in this function)
arch/arm/plat-omap/include/plat/voltage.h:145: error: (Each undeclared identifier is reported only once
arch/arm/plat-omap/include/plat/voltage.h:145: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-omap2/omap_hwmod_common_data.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
The error is reported when omap2plus_defconfig built with CONFIG_PM disabled
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
LD init/built-in.o
LD .tmp_vmlinux1
arch/arm/mach-omap2/built-in.o: In function `omap2_set_init_voltage':
arch/arm/mach-omap2/pm.c:181: undefined reference to `omap_voltage_domain_lookup'
arch/arm/mach-omap2/built-in.o: In function `omap4_twl_init':
arch/arm/mach-omap2/omap_twl.c:244: undefined reference to `omap_voltage_domain_lookup'
arch/arm/mach-omap2/omap_twl.c:247: undefined reference to `omap_voltage_domain_lookup'
arch/arm/mach-omap2/omap_twl.c:250: undefined reference to `omap_voltage_domain_lookup'
make: *** [.tmp_vmlinux1] Error 1
The error is reported when omap2plus_defconfig built with CONFIG_PM disabled
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Fix below build warnings
CC arch/arm/mach-omap2/common.o
CC arch/arm/mach-omap2/gpio.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/gpio.c:25:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/dma.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/dma.c:32:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/wd_timer.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/wd_timer.c:15:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/prm44xx.o
CC arch/arm/mach-omap2/omap_hwmod.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/omap_hwmod.c:145:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/omap_hwmod_common_data.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/omap_hwmod_common_data.c:20:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
The error is reported when omap2plus_defconfig built with CONFIG_PM disabled
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
struct clockdomain member clktrctrl_mask is available for only for OMAP2
and OMAP3 architectures. Technially it is also used only for these archs
but this breaks the build with custom OMAP4 configuration.
CC arch/arm/mach-omap2/clockdomain.o
arch/arm/mach-omap2/clockdomain.c: In function '_enable_hwsup':
arch/arm/mach-omap2/clockdomain.c:251: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:254: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function '_disable_hwsup':
arch/arm/mach-omap2/clockdomain.c:277: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:280: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_sleep':
arch/arm/mach-omap2/clockdomain.c:744: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_wakeup':
arch/arm/mach-omap2/clockdomain.c:789: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_clk_enable':
arch/arm/mach-omap2/clockdomain.c:922: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:926: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_clk_disable':
arch/arm/mach-omap2/clockdomain.c:994: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:998: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
make[1]: *** [arch/arm/mach-omap2/clockdomain.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Fix the build break by dropping the #ifdef as suggested by Paul Walmsley
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Instead of accessing the irq_desc array directly
we can use irq_to_desc(irq). That will allow us to,
if wanted, select SPARSE_IRQ and irq_descs will be
added to a radix tree, instead of a array.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap_pm_runtime_suspend and omap_pm_runtime_resume are used
as function pointers and does not really need to be exposed
to the world.
Fixes sparse warnings:
arch/arm/mach-omap2/pm_bus.c:23:5: warning: symbol 'omap_pm_runtime_suspend' was not declared. Should it be static?
arch/arm/mach-omap2/pm_bus.c:40:5: warning: symbol 'omap_pm_runtime_resume' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case on OMAP2+ we call set_24xx_gpio_triggering() instead of
updating reg and l values. However, at the end of the function we
perform a write:
__raw_writel(l, reg);
So on OMAP2+ we end up writing 0 to the bank->base which is not
correct (typically this points to GPIO_REVISION register).
Fix this by returning immediately after call to
set_24xx_gpio_triggering().
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
twl_init functions are declared in pm.h and used in pm.c
pm.h header defining the protos need to be included to
ensure that omap_twl.c has consistent function definition.
This fixes sparse warning:
arch/arm/mach-omap2/omap_twl.c:237:12: warning: symbol 'omap4_twl_init' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:256:12: warning: symbol 'omap3_twl_init' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The uv_to_vsel, vsel_to_uv functions don't need to be exposed to the
world as they are used as function pointers. make them static.
Fixes sparse warnings:
arch/arm/mach-omap2/omap_twl.c:63:15: warning: symbol 'twl4030_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:68:4: warning: symbol 'twl4030_uv_to_vsel' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:73:15: warning: symbol 'twl6030_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:105:4: warning: symbol 'twl6030_uv_to_vsel' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap_enable_smartreflex_on_init is meant to be used by boards
which would like to have SR enabled by default on the platform, while
omap_devinit_smartreflex is used by pm code, the protos are defined
in pm.h. This header should be included to ensure that sr_device
function definitions match the prototypes.
including pm.h fixes the sparse warnings (with CONFIG_OMAP_SMARTREFLEX=y):
arch/arm/mach-omap2/sr_device.c:138:13: warning: symbol 'omap_enable_smartreflex_on_init' was not declared. Should it be static?
arch/arm/mach-omap2/sr_device.c:143:12: warning: symbol 'omap_devinit_smartreflex' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
1. changes some register address to fit macro definition
2. add platform data and clock for sdhc
Signed-off-by: Yong Shen <yong.shen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
1. Adjust FEC base address name to fit macro definition
2. Add platform data and reset function for FEC
Signed-off-by: Yong Shen <yong.shen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
omap2_wd_timer_disable is declared in wdtimer.h and used by hwmod
function pointers for usage, the header inclusion is necessary
to ensure that the prototype and function remains consistent.
omap_wdt_latency is passed as a pointer and does not need global scope
Fixes sparse warnings:
arch/arm/mach-omap2/devices.c:981:31: warning: symbol 'omap_wdt_latency' was not declared. Should it be static?
arch/arm/mach-omap2/wd_timer.c:27:5: warning: symbol 'omap2_wd_timer_disable' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
igep3_flash_init is not used beyond the scope of the file, make it
static instead.
Fixes sparse warning:
arch/arm/mach-omap2/board-igep0030.c:106:13: warning: symbol 'igep3_flash_init' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_zoom_wlan_data and zoom2_set_hs_extmute are not used beyond
the scope of zoom-peripherals directly, instead pointers are used.
make them static instead.
Fixes sparse warnings:
arch/arm/mach-omap2/board-zoom-peripherals.c:193:29: warning: symbol 'omap_zoom_wlan_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:245:6: warning: symbol 'zoom2_set_hs_extmute' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux data is passed by pointers to mux.c from the SoC specific
mux file, these variables dont really need to be global scope.
This fixes the following sparse warnings:
arch/arm/mach-omap2/mux44xx.c:547:29: warning: symbol 'omap4_core_cbl_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux44xx.c:1265:29: warning: symbol 'omap4_core_cbs_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux44xx.c:1549:29: warning: symbol 'omap4_wkup_cbl_cbs_ball' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
memcpy() copies 8 bytes too much (omap_mux_entry vs. omap_mux). Correct
by replacing memcpy() with struct assignment, which is safer.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This option uses LDREXB/STREXB to emulate SWPB but these instructions
are not supported on all the ARMv6 processors.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Leif Lindholm <Leif.Lindholm@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
omap2: Make OMAP2PLUS select OMAP_DM_TIMER
OMAP4: hwmod data: Fix alignment and end of line in structurefields
OMAP4: hwmod data: Move the DMA structures
OMAP4: hwmod data: Move the smartreflex structures
OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
arm: omap: tusb6010: add name for MUSB IRQ
arm: omap: craneboard: Add USB EHCI support
omap2+: Initialize serial port for dynamic remuxing for n8x0
omap2+: Add struct omap_board_data and use it for platform level serial init
omap2+: Allow hwmod state changes to mux pads based on the state changes
omap2+: Add support for hwmod specific muxing of devices
omap2+: Add omap_mux_get_by_name
OMAP2: PM: fix compile error when !CONFIG_SUSPEND
MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
OMAP4: Smartreflex framework extensions
OMAP4: hwmod: Add inital data for smartreflex modules.
OMAP4: PM: Program correct init voltages for scalable VDDs
OMAP4: Adding voltage driver support
OMAP4: Register voltage PMIC parameters with the voltage layer
OMAP3: PM: Program correct init voltages for VDD1 and VDD2
...
Fix up trivial conflict in arch/arm/plat-omap/Kconfig
Remove now unused IRQ demux code. All R-Mobile and
SH-Mobile processors should register IRQ demux
handlers during run-time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break-out GIC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.
Covers sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break-out INTC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.
Covers sh7367, sh7377 and sh7372.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the R-Mobile / SH-Mobile processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When CONFIG_ZBOOT_ROM is selected, the resulting zImage file will be small
boot loader and may be burned to rom or flash.
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (416 commits)
ARM: DMA: add support for DMA debugging
ARM: PL011: add DMA burst threshold support for ST variants
ARM: PL011: Add support for transmit DMA
ARM: PL011: Ensure IRQs are disabled in UART interrupt handler
ARM: PL011: Separate hardware FIFO size from TTY FIFO size
ARM: PL011: Allow better handling of vendor data
ARM: PL011: Ensure error flags are clear at startup
ARM: PL011: include revision number in boot-time port printk
ARM: vexpress: add sched_clock() for Versatile Express
ARM i.MX53: Make MX53 EVK bootable
ARM i.MX53: Some bug fix about MX53 MSL code
ARM: 6607/1: sa1100: Update platform device registration
ARM: 6606/1: sa1100: Fix platform device registration
ARM i.MX51: rename IPU irqs
ARM i.MX51: Add ipu clock support
ARM: imx/mx27_3ds: Add PMIC support
ARM: DMA: Replace page_to_dma()/dma_to_page() with pfn_to_dma()/dma_to_pfn()
mx51: fix usb clock support
MX51: Add support for usb host 2
arch/arm/plat-mxc/ehci.c: fix errors/typos
...
Add ARM support for the DMA debug infrastructure, which allows the
DMA API usage to be debugged.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (35 commits)
mmc: msm_sdcc: Check for only DATA_END interrupt to end a request
mmc: msm_sdcc: Fix bug in PIO mode when data size is not word aligned
mmc: msm_sdcc: Reset SDCC in case of data transfer errors
mmc: msm_sdcc: Add prog done interrupt support
mmc: msm_sdcc: Fix possible circular locking dependency warning
MSM: Add USB support for MSM7x30
MSM: Add USB suport for QSD8x50
msm: initial framebuffer support
msm: add handling for clocks tagged as CLK_MINMAX
msm: trout: change name of pmdh_clk to mddi_clk
msm: add CLK_MINMAX to pmdh_clk
msm: trout: add gpio_to_irq
msm: iommu: Use the correct memory allocation flag
msm_serial: Remove redundant unlikely()
msm: iommu: Miscellaneous code cleanup
msm: iommu: Support cache-coherent memory access
msm: iommu: Definitions for extended memory attributes
msm: iommu: Kconfig dependency for the IOMMU API
msm: iommu: Check if device is already attached
msm: iommu: Kconfig item for cacheable page tables
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1436 commits)
cassini: Use local-mac-address prom property for Cassini MAC address
net: remove the duplicate #ifdef __KERNEL__
net: bridge: check the length of skb after nf_bridge_maybe_copy_header()
netconsole: clarify stopping message
netconsole: don't announce stopping if nothing happened
cnic: Fix the type field in SPQ messages
netfilter: fix export secctx error handling
netfilter: fix the race when initializing nf_ct_expect_hash_rnd
ipv4: IP defragmentation must be ECN aware
net: r6040: Return proper error for r6040_init_one
dcb: use after free in dcb_flushapp()
dcb: unlock on error in dcbnl_ieee_get()
net: ixp4xx_eth: Return proper error for eth_init_one
include/linux/if_ether.h: Add #define ETH_P_LINK_CTL for HPNA and wlan local tunnel
net: add POLLPRI to sock_def_readable()
af_unix: Avoid socket->sk NULL OOPS in stream connect security hooks.
net_sched: pfifo_head_drop problem
mac80211: remove stray extern
mac80211: implement off-channel TX using hw r-o-c offload
mac80211: implement hardware offload for remain-on-channel
...
Prevent OneNAND's voltage regulator from going to sleep while
OneNAND is in use, by explicitly enabling and disabling the
regulator as appropriate.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a common requirement for not using OMAP specific omap_readw() /
omap_writew() function calls in drivers/, but replace them with
readw() / writew() on ioremap()ped addresses passed from arch/ instead.
The patch implements this idea for the Amstrad Delta NAND driver. To be
able to use the modified driver, the board file is updated with the
platform device I/O resource declaration, which is passed from there.
Created and tested against linux-2.6.37-rc5, on top of recent patch
'MTD: NAND: ams-delta: convert to platform driver'.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In its current form, the driver may interfere with different hardware on
different boards if built into the kernel, hence is not suitable for
inclusion into a defconfig, inteded to be usable with multiple OMAP1 cpu and
machine types.
Convert it to a platform driver, that should be free from this issue.
Created and tested against linux-2.6.37-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Both S3C2443 and S3C2416 support 4 UART channels, this patch adds support
for the missing uart channel.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There are few functions marked as __init, but exported to modules in
devices declaration files.
s3c_nand_set_platdata() and s3c24xx_ts_set_platdata() are used only by
boards init code now, so remove EXPORT_SYMBOL() for them.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2443 has two-bits pull-up/pull-down configuration fields in GPIO
registers, but values are differ from other SoCs with two-bits
configuration. gpio-cfg-helpers.h already has prototypes for
s3c2443-style pull-up/down methods, so implement them.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Enable card detect by GPIO pin on hsmmc1 device (SD0 on SMDK2416 board)
and enable card polling on hsmmc0 (SD1).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Samsung S3C2416 has two SDHCI controllers compatible with other
Samsung's SoCs (S3C64XX, S5PC100 etc...).
Add required platform setup code that the devices can be used with
sdhci-s3c driver.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
[kgene.kim@samsung.com: change to __raw_{readl,writel} from {readl,writel}]
[kgene.kim@samsung.com: build error fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Define maps for HSMMC devices.
S3C2443 has one HSMMC device with base address 0x4A800000.
S3C2416 has HSMMC0 at 0x4AC00000 and HSMMC1 at 0x4A800000.
So suppose that S3C2443 has only HSMMC1.
Define clock for hsmmc0 device and register it.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
fsib_clk will be used when fdiv_clk failed on fsi_hdmi_set_rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a sched_clock() implementation to Versatile Express using the new
sched_clock() infrastructure for extending 32bit counters to full
64-bit nanoseconds.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
