it87: Add support for the IT8716F
The IT8716F is a Super-I/O chip with integrated hardware monitoring
functions. It is very similar to the IT8712F, so adding support to the
it87 driver was pretty straightforward. The most significant change here
is that the IT8716F has 16-bit fan speed counters, so the user no more
needs to tweak the fan clock dividers to get the best readings.
Userspace support is already in lm_sensors SVN (to be soon released
as 2.10.1.)
Thanks to Stian Oksavik, Olivier Nicolas, Prakash Punnoor and
Juergen Kilb for testing the early versions of this patch.
Thanks also to ITE for providing datasheets and answering my questions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add documentation for the w83627ehf hardware monitoring driver.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
[PATCH] bonding: update version number
[PATCH] git-netdev-all: pc300_tty build fix
[PATCH] Make PC300 WAN driver compile again
[PATCH] Modularize generic HDLC
[PATCH] more s2io __iomem annotations
[PATCH] restore __iomem annotations in e1000
[PATCH] 64bit bugs in s2io
[PATCH] bonding: Fix primary selection error at enslavement time
[PATCH] bonding: Don't mangle LACPDUs
[PATCH] bonding: Validate probe replies in ARP monitor
[PATCH] bonding: Don't release slaves when master is admin down
[PATCH] bonding: Add priv_flag to avoid event mishandling
[PATCH] bonding: Handle large hard_header_len
[PATCH] bonding: Remove unneeded NULL test
[PATCH] bonding: Format fix in seq_printf call
[PATCH] bonding: Convert delay value from s16 to int
[PATCH] bonding: Allow bonding to enslave a 10 Gig adapter
Delete unused drivers/net/gt64240eth.h
[PATCH] skge: fiber support
[PATCH] fix possible NULL ptr deref in forcedeth
...
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Ontrak ADU USB devices.
Fixed for printk issues by Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Steven Haigh <netwiz@crc.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add driver for AIRcable USB Bluetooth dongle.
Signed-off-by: Naranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A little more detail on how and when to poll() /proc/bus/usb/devices.
Signed-off-by: Sam Bishop <sam@bishop.dhs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Resetting the devices during driver initialization can be a costly
operation in terms of time (especially scsi devices). This option can be
used by drivers to know that user forcibly wants the devices to be reset
during initialization.
This option can be useful while kernel is booting in unreliable
environment. For ex. during kdump boot where devices are in unknown
random state and BIOS execution has been skipped.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make futexes work under NOMMU conditions.
This can be tested by running this in one shell:
#define SYSERROR(X, Y) \
do { if ((long)(X) == -1L) { perror(Y); exit(1); }} while(0)
int main()
{
int shmid, tmp, *f, n;
shmid = shmget(23, 4, IPC_CREAT|0666);
SYSERROR(shmid, "shmget");
f = shmat(shmid, NULL, 0);
SYSERROR(f, "shmat");
n = *f;
printf("WAIT: %p{%x}\n", f, n);
tmp = futex(f, FUTEX_WAIT, n, NULL, NULL, 0);
SYSERROR(tmp, "futex");
printf("WAITED: %d\n", tmp);
tmp = shmdt(f);
SYSERROR(tmp, "shmdt");
exit(0);
}
And then this in the other shell:
#define SYSERROR(X, Y) \
do { if ((long)(X) == -1L) { perror(Y); exit(1); }} while(0)
int main()
{
int shmid, tmp, *f;
shmid = shmget(23, 4, IPC_CREAT|0666);
SYSERROR(shmid, "shmget");
f = shmat(shmid, NULL, 0);
SYSERROR(f, "shmat");
(*f)++;
printf("WAKE: %p{%x}\n", f, *f);
tmp = futex(f, FUTEX_WAKE, 1, NULL, NULL, 0);
SYSERROR(tmp, "futex");
printf("WOKE: %d\n", tmp);
tmp = shmdt(f);
SYSERROR(tmp, "shmdt");
exit(0);
}
The first program will set up a SYSV IPC SHM segment and wait on a futex in it
for the number at the start to change. The program will increment that number
and wake the first program up. This leads to output of the form:
SHELL 1 SHELL 2
======================= =======================
# /dowait
WAIT: 0xc32ac000{0}
# /dowake
WAKE: 0xc32ac000{1}
WAITED: 0 WOKE: 1
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add documentation about using shared memory in NOMMU mode.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make mremap() partially work for NOMMU kernels. It may resize a VMA provided
that it doesn't exceed the size of the slab object in which the storage is
allocated that the VMA refers to. Shareable VMAs may not be resized.
Moving VMAs (as permitted by MREMAP_MAYMOVE) is not currently supported.
This patch also makes use of the fact that the VMA list is now ordered to cut
it short when possible.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement /proc/pid/maps for NOMMU by reading the vm_area_list attached to
current->mm->context.vmlist.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6: (30 commits)
i2c: Drop unimplemented slave functions
i2c: Constify i2c_algorithm declarations, part 2
i2c: Constify i2c_algorithm declarations, part 1
i2c: Let drivers constify i2c_algorithm data
i2c-isa: Restore driver owner
i2c-viapro: Add support for the VT8237A and VT8251
i2c: Warn on i2c client creation failure
i2c-core: Drop useless bitmaskings
i2c-algo-pcf: Discard the mdelay data struct member
i2c-algo-bit: Cleanups
i2c-isa: Fail adding driver on attach_adapter error
i2c: __must_check fixes (chip drivers)
i2c-dev: attach/detach_adapter cleanups
i2c-stub: Chip address as a module parameter
i2c: Plan i2c-isa for removal
i2c: New bus driver for TI OMAP boards
i2c-algo-bit: Discard the mdelay data struct member
i2c-matroxfb: Struct init conversion
i2c: Fix copy-n-paste in subsystem Kconfig
i2c-au1550: Add I2C support for Au1200
...
Initial register bank cleanup. Make SR.RB configurable, and add some
preliminary documentation on register bank usage within the kernel.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PCI-Express AER (Advanced Error Reporting) provides more robust error reporting.
The series of patches enable kernel support to AER.
The initial patches were written by Tom Long Nguyen. I ported them to the kernel
2.6.18-rc3. Many thanks to Rajesh Shah and Narayanan Chandramouli for their great
review comments and testing help.
Patch 1 consists of the pciaer-howto.txt document.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-viapro: Add support for the VT8237A and VT8251
Documentation update included. Compile tested.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-stub: Chip address as a module parameter
Add a mandatory chip_addr parameter to i2c-stub. This parameter
defines to which chip address the driver will respond, instead of
reponding to all addresses as before. The idea is to prevent the
users from loading i2c-stub at random and being then confused by
the results of sensors-detect or other user-space tools.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c: Plan i2c-isa for removal
i2c-isa doesn't make much sense in the device driver model. Drivers
relying on it are better implemented as platform drivers. We must
wait for recent versions of libsensors (2.10.0 or later) to be widely
deployed beforehand, though. This move should also make it easier to
convert i2c-core to the device driver model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (225 commits)
[PATCH] Don't set calgary iommu as default y
[PATCH] i386/x86-64: New Intel feature flags
[PATCH] x86: Add a cumulative thermal throttle event counter.
[PATCH] i386: Make the jiffies compares use the 64bit safe macros.
[PATCH] x86: Refactor thermal throttle processing
[PATCH] Add 64bit jiffies compares (for use with get_jiffies_64)
[PATCH] Fix unwinder warning in traps.c
[PATCH] x86: Allow disabling early pci scans with pci=noearly or disallowing conf1
[PATCH] x86: Move direct PCI scanning functions out of line
[PATCH] i386/x86-64: Make all early PCI scans dependent on CONFIG_PCI
[PATCH] Don't leak NT bit into next task
[PATCH] i386/x86-64: Work around gcc bug with noreturn functions in unwinder
[PATCH] Fix some broken white space in ia32_signal.c
[PATCH] Initialize argument registers for 32bit signal handlers.
[PATCH] Remove all traces of signal number conversion
[PATCH] Don't synchronize time reading on single core AMD systems
[PATCH] Remove outdated comment in x86-64 mmconfig code
[PATCH] Use string instructions for Core2 copy/clear
[PATCH] x86: - restore i8259A eoi status on resume
[PATCH] i386: Split multi-line printk in oops output.
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (47 commits)
Driver core: Don't call put methods while holding a spinlock
Driver core: Remove unneeded routines from driver core
Driver core: Fix potential deadlock in driver core
PCI: enable driver multi-threaded probe
Driver Core: add ability for drivers to do a threaded probe
sysfs: add proper sysfs_init() prototype
drivers/base: check errors
drivers/base: Platform notify needs to occur before drivers attach to the device
v4l-dev2: handle __must_check
add CONFIG_ENABLE_MUST_CHECK
add __must_check to device management code
Driver core: fixed add_bind_files() definition
Driver core: fix comments in drivers/base/power/resume.c
sysfs_remove_bin_file: no return value, dump_stack on error
kobject: must_check fixes
Driver core: add ability for devices to create and remove bin files
Class: add support for class interfaces for devices
Driver core: create devices/virtual/ tree
Driver core: add device_rename function
Driver core: add ability for classes to handle devices properly
...
Add the pm_trace attribute in /sys/power which has to be explicitly set to
one to really enable the "PM tracing" code compiled in when CONFIG_PM_TRACE
is set (which modifies the machine's CMOS clock in unpredictable ways).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a boot parameter to reserve high linear address space for hypervisors.
This is necessary to allow dynamically loaded hypervisor modules, which might
not happen until userspace is already running, and also provides a useful tool
to benchmark the performance impact of reduced lowmem address space.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently one can enable slab reclaim by setting an explicit option in
/proc/sys/vm/zone_reclaim_mode. Slab reclaim is then used as a final
option if the freeing of unmapped file backed pages is not enough to free
enough pages to allow a local allocation.
However, that means that the slab can grow excessively and that most memory
of a node may be used by slabs. We have had a case where a machine with
46GB of memory was using 40-42GB for slab. Zone reclaim was effective in
dealing with pagecache pages. However, slab reclaim was only done during
global reclaim (which is a bit rare on NUMA systems).
This patch implements slab reclaim during zone reclaim. Zone reclaim
occurs if there is a danger of an off node allocation. At that point we
1. Shrink the per node page cache if the number of pagecache
pages is more than min_unmapped_ratio percent of pages in a zone.
2. Shrink the slab cache if the number of the nodes reclaimable slab pages
(patch depends on earlier one that implements that counter)
are more than min_slab_ratio (a new /proc/sys/vm tunable).
The shrinking of the slab cache is a bit problematic since it is not node
specific. So we simply calculate what point in the slab we want to reach
(current per node slab use minus the number of pages that neeed to be
allocated) and then repeately run the global reclaim until that is
unsuccessful or we have reached the limit. I hope we will have zone based
slab reclaim at some point which will make that easier.
The default for the min_slab_ratio is 5%
Also remove the slab option from /proc/sys/vm/zone_reclaim_mode.
[akpm@osdl.org: cleanups]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add autodetection for PCI subsystem ID 107d:6632, to detect as
a Leadtek PVR 2000
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is the first in a series of patches to add full WinTV-HVR1300
support to Linux. This first patch will enable analog TV support
and DVB-T support. Later patches will add the hardware MPEG encoder
support.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add card support for Proteus Pro 2309, based on saa7130 bridge
Signed-off-by: Michal Majchrowicz <mmajchrowicz@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Software I2C were using a very conservative value of udelay=16, meaning about
20Kbps. According with Philips I2C datasheet, the i2c should answer well for
times at the order of 4.7 us. So, using udelay=5 should work for all devices.
After this patch, the speed should be close to 66,67 Kbps, with the current
kernel software bitbang, with 30/60 duty cycle.
Anyway, added a new parameter (i2c_udelay) that would allow using conservative
values, if eventually a hardware doesn't support the datasheet values.
Thanks to Jean Delvare <khali@linux-fr.org> for pointing this improvement.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Updates feature-removal-schedule.txt to reflect the current scheduled date
to convert all V4L1 drivers to V4L2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
README.hm12: documentation on the HM12 YUV format used by the cx23415/6 chip.
README.vbi: documentation on the V4L2_MPEG_STREAM_VBI_FMT_IVTV VBI format
used in MPEG streams.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Acorp TV134DS and FlyDVB-S cards (both based on
tda10086+tda826x)
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Shenzhen Tungsten Ages Tech TE-DTV-250 OEM for
Swann PCI TV Tuner Card
Signed-off-by: David Bussenschutt <buzz@oska.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for Norwood PCI TV Tuner (non-pro)
Signed-off-by: Peter Naulls <peter@chocky.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds autodetection support for the AverMedia M150-D
blackbird MPEG encoder / analog video capture card.
This board is known to work with the ASUS PVR 416 configuration.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add initial support for Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
only analog is working for now
Signed-off-by: Eric Thomas <ethomas@claranet.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It is just another Lifeview clone
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The change is just an additional PCI ID
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Analog TV, CVBS, S-video and DVB-T are working,
DVB-S not yet
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some buggy systems can machine check when config space accesses
happen for some non existent devices. i386/x86-64 do some early
device scans that might trigger this. Allow pci=noearly to disable
this. Also when type 1 is disabling also don't do any early
accesses which are always type1.
This moves the pci= configuration parsing to be a early parameter.
I don't think this can break anything because it only changes
a single global that is only used by PCI.
Cc: gregkh@suse.de
Cc: Trammell Hudson <hudson@osresearch.net>
Signed-off-by: Andi Kleen <ak@suse.de>
Describes the stack organization on x86-64.
I changed it a bit and removed some obsolete information and the
questions.
Cc: kaos@sgi.com
Signed-off-by: Andi Kleen <ak@suse.de>
... instead of using a CONFIG option. The config option still controls
if the resulting executable actually has unwind information.
This is useful to prevent compilation errors when users select
CONFIG_STACK_UNWIND on old binutils and also allows to use
CFI in the future for non kernel debugging applications.
Cc: jbeulich@novell.com
Cc: sam@ravnborg.org
Signed-off-by: Andi Kleen <ak@suse.de>
Adds a new /proc/sys/kernel/nmi_watchdog call that will enable/disable the
nmi watchdog.
By entering a non-zero value here, a user can enable the nmi watchdog to
monitor the online cpus in the system. By entering a zero value here, a
user can disable the nmi watchdog and free up a performance counter which
could then be utilized by the oprofile subsystem, otherwise oprofile may be
short a counter when in use.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The file sysfs-power that documents the interface in the /sys/power/ directory
is added to Documentation/ABI/testing.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lists the /sys/devices/.../power/state file, and its internal support,
as due for removal next year.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This turned into a rewrite of Documentation/power/devices.txt:
- Provide more of the "big picture"
- Fixup some of the horribly ancient/obsolete description of device suspend()
semantics; lots of text just got deleted.
- Add a decent description of PM_EVENT_* codes, including the new PRETHAW code
needed in some swsusp scenarios.
- Describe the new PM factorization from Linus:
* class suspend, current suspend, then suspend_late
* NOT suspend_prepare, it wasn't really usable
* resume_early, current resume, class resume.
- Updates power/state docs to be correct, and deprecate its usage except for
driver testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
deprecate PHYSDEV* values in the uevent environment
These values are no longer needed and inconsistent with the
stacking of class devices. The event environment should not
carry properties of a parent device. The key PHYSDEVDRIVER is
available as DRIVER, PHYDEVBUS is indentical SUBSYSTEM. Class
devices should not carry any of these values.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add logic to check ARP request / reply packets used for ARP
monitor link integrity checking.
The current method simply examines the slave device to see if it
has sent and received traffic; this can be fooled by extraneous traffic.
For example, if multiple hosts running bonding are behind a common
switch, the probe traffic from the multiple instances of bonding will
update the tx/rx times on each other's slave devices.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes up a couple of conflicts when merging up with
Linus' latest kernel. This will hopefully allow GFS2 to
be more easily merged into forthcoming -mm and FC kernels
due to the "one line per header" format now used for the
kernel headers.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Conflicts:
include/linux/Kbuild
include/linux/kernel.h
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (28 commits)
kbuild: add distclean info to 'make help' and more details for 'clean'
dontdiff: add utsrelease.h
kbuild: fix "mkdir -p" usage in scripts/package/mkspec
kbuild: correct and clarify versioning info in Makefile
kbuild: fixup Documentation/kbuild/modules.txt
kbuild: Extend kbuild/defconfig tags support to exuberant ctags
kbuild: fix for some typos in Documentation/makefiles.txt
kbuild: clarify "make C=" build option
Documentaion: update Documentation/Changes with minimum versions
kbuild: update help in top level Makefile
kbuild: fail kernel compilation in case of unresolved module symbols
kbuild: remove debug left-over from Makefile.host
kbuild: create output directory for hostprogs with O=.. build
kbuild: add missing return statement in modpost.c:secref_whitelist()
kbuild: preperly align SYSMAP output
kbuild: make -rR is now default
kbuild: make V=2 tell why a target is rebuild
kbuild: modpost on vmlinux regardless of CONFIG_MODULES
kbuild: ignore references from ".pci_fixup" to ".init.text"
kbuild: linguistic fixes for Documentation/kbuild/makefiles.txt
...
I noticed a few typos while reading makefiles.txt to learn about the
kbuild system. Attached is a patch against 2.6.18 to fix them.
Remove trailing whitespace while we are there..
Signed-off-by: Bryce Harrington <bryce@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Based on conversations with greg kh (and noticing a simple typo),
these are the actual minimal versions for 2.6.18.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
I have done a look-through through Documentation/kbuild/ and my corrections
(proposed) are attached.
Cc'ed are original author Michael (responsible for comitting changes to
these files?), Sam (kbuild maintainer), Adrian (-trivial maintainer).
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
I have done a look-through through Documentation/kbuild/ and my corrections
(proposed) are attached.
Cc'ed are original author Michael (responsible for comitting changes to
these files?), Sam (kbuild maintainer), Adrian (-trivial maintainer).
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
I have done a look-through through Documentation/kbuild/ and my corrections
(proposed) are attached.
Cc'ed are original author Michael (responsible for comitting changes to
these files?), Sam (kbuild maintainer), Adrian (-trivial maintainer).
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This has been discussed on dccp@vger and removes the necessity for applications
to supply service codes in each and every case.
If an application does not want to provide a service code, that's fine, it will
be given 0. Otherwise, service codes can be set via socket options as before.
This patch has been tested using various client/server configurations
(including listening on multiple service codes).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (50 commits)
[libata] Delete pata_it8172 driver
[PATCH] libata: improve handling of diagostic fail (and hardware that misreports it)
[PATCH] libata: fix non-uniform ports handling
Fix libata resource conflict for legacy mode
[libata] ata_piix: build fix
[PATCH] pata_amd: Check enable bits on Nvidia
[PATCH] Update SiS PATA
[libata] Add pata_jmicron driver to Kconfig, Makefile
[libata #pata-drivers] Trim trailing whitespace.
[libata] Trim trailing whitespace.
[libata] Add a bunch of PATA drivers.
Rename libata-bmdma.c to libata-sff.c.
libata: Grand renaming.
Clean up drivers/ata/Kconfig a bit.
[PATCH] CONFIG_PM=n slim: drivers/scsi/sata_sil*
[PATCH] sata_via: Add SATA support for vt8237a
[PATCH] libata: change path to libata in libata.tmpl
[PATCH] libata: s/CONFIG_SCSI_SATA/CONFIG_[S]ATA/g in pci/quirks.c
libata: Make sure drivers/ata is a separate Kconfig menu
[libata] ata_piix: add missing kfree()
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
Received from Mark Salyzyn:
This patch to the driver's documentation adds a few new product entries,
sorts the entries on OEM lines first for easy searching, followed by
product id order to make it easier to compare against the open source
pci list. The driver has 'family match' so is somewhat future proof, no
code changes are required to recognize the new products.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (148 commits)
[ALSA] intel8x0m - Free irq in suspend
[ALSA] Move CONFIG_SND_AC97_POWER_SAVE to pci/Kconfig
[ALSA] usb-audio: add mixer control names for the Aureon 5.1 MkII
[ALSA] ES1938: remove duplicate field initialization
[ALSA] usb-audio: increase number of packets per URB
[ALSA] hda-codec - Fix headphone auto-toggle on sigmatel codec
[ALSA] hda-intel - A slight cleanup of timeout check in azx_get_response()
[ALSA] hda-codec - Fix mic input with STAC92xx codecs
[ALSA] mixart: Use SEEK_{SET,CUR,END} instead of hardcoded values
[ALSA] gus: Use SEEK_{SET,CUR,END} instead of hardcoded values
[ALSA] opl4: Use SEEK_{SET,CUR,END} instead of hardcoded values
[ALSA] sound core: Use SEEK_{SET,CUR,END} instead of hardcoded values
[ALSA] hda-codec - Support multiple headphone pins
[ALSA] hda_intel prefer 24bit instead of 20bit
[ALSA] hda-codec - Add vendor ids for Motorola and Conexant
[ALSA] hda-codec - Add device id for Motorola si3054-compatible codec
[ALSA] Add missing compat ioctls for ALSA control API
[ALSA] powermac - Fix Oops when conflicting with aoa driver
[ALSA] aoa: add locking to tas codec
[ALSA] hda-intel - Fix suspend/resume with MSI
...
Fix the order to call pci_disable_msi() to be after free_irq().
(Otherwise pci_disable_msi() bugs you.)
Also, added a description of disable_msi option to documentation.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the support for LG LW25 laptop with ALC880 codec.
It's the same codec model as LG LW20 (model=lg-lw).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch renames the 965_2112 function ids to 965_3ST, and
adds functional support for 965_5ST (5 stack 7.1 surround).
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- AR11M and AR11S uses the same chip hence we claim to support the AR Series.
- Added commentary about STAC9225s which shares the same id as CXD9872RD.
- Added entry for 7662 but won't work automatically until pci_subdevice
is known.
- 'vaio' model now corresponds to CXD9872RD_VAIO for backward compat.
- Replaced STAC766x_VAIO with CXD9872RD_VAIO, STAC9872AK_VAIO, STAC9872K_VAIO
and CXD9872AKD_VAIO
- Added 'vaio-ar' model for potential future modifications.
Signed-off-by: Guillaume Munch <diabo@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Patch enables the internal speaker on acer laptops with ALC883.
Signed-off-by: Vladimir Avdonin <vldmrrr@yahoo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds automatic detection for Sigmatel ID 7664,
the sound chip in Sony Vaio AR 11B (european name).
- patch_stac7661 becomes patch_stac766x
- .id = 0x83847664 is added
Signed-off-by: Guillaume Munch <diabo@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added a new model 'uniwill-m31' for Uniwill laptops with ALC861
codec chip. The patch is taken from ALSA bug#2035, and modifeid.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Added model=arima for Arima W820Di1 with ALC882 codec chip
- Added EAPD-control verbs to TCL S700 init verbs
- Added missing model strings for Realtek codecs (to be specified
via module option explicitly for testing/debugging)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the support of Benq laptop with ALC262 codec.
A model string 'benq' is added, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the proper model entry for Clevo m665n laptop with ALC880 codec.
Also, added a model string 'clevo' to enable the clevo-type model option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
We do not always need proxy NDP functionality even we
enable forwarding.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation for the NetLabel system, this includes a basic overview
of how NetLabel works, how LSM developers can integrate it into their
favorite LSM, as well as documentation on the CIPSO related sysctl
variables. Also, due to the difficulty of finding expired IETF
drafts, I am including the IETF CIPSO draft that is the basis of the
NetLabel CIPSO implementation.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds security to flow key for labeling of flows as also to allow
for making flow cache lookups based on the security label seemless.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the documentation to reflect the switch from digest
to hash. It also replaces notes about emailing James Morris to refer
to me instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commits 11012d419c and
40dd2d20f2, which allowed us to use the
MMIO accesses for PCI config cycles even without the area being marked
reserved in the e820 memory tables.
Those changes were needed for EFI-environment Intel macs, but broke some
newer Intel 965 boards, so for now it's better to revert to our old
2.6.17 behaviour and at least avoid introducing any new breakage.
Andi Kleen has a set of patches that work with both EFI and the broken
Intel 965 boards, which will be applied once they get wider testing.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Edgar Hucek <hostmaster@ed-soft.at>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code for frame diverter is unmaintained and has bitrotted.
The number of users is very small and the code has lots of problems.
If anyone is using it, they maybe exposing themselves to bad packet attacks.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure if documenting this here is appropriate, but
if it is, here is some text to put there.
Signed-Off-By: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn Appropriate Byte Count off by default because it unfairly
penalizes applications that do small writes. Add better documentation
to describe what it is so users will understand why they might want to
turn it on.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the scheduled removal of the force_inquiry_hack
module parameter.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add support for new hardware and bumps the version to 3.6.10. It seems
there were several changes introduced including soft_irq. I decided to
bump the major number to reflect these changes. Since we're still
supporting older vendor kernels I need some way differentiate between
kernel versions <=2.6.10 and newer kernels >=2.6.16.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Claim an ID number for Xen in the LOADER_TYPE field.
Also, keep the table in zero-page.txt consistent with boot.txt.
[hpa says: 6 was skipped because I couldn't rule out that it hadn't been
unofficially used. It seemed easier to skip it for now.]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The DCO does not mean anything if we allow anonymous contributors to the
kernel. As this is an open source project, we need to do everything in the
open.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch schedules obsolete OSS drivers (with ALSA drivers that support
the same hardware) for removal.
A rationale of the patch is in
http://lkml.org/lkml/2006/7/11/186
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix return value from memcpy
[POWERPC] iseries: Define insw et al. so libata/ide will compile
[POWERPC] Fix irq enable/disable in smp_generic_take_timebase
[POWERPC] Fix problem with time not advancing on 32-bit platforms
[POWERPC] Restore copyright notice in arch/powerpc/kernel/fpu.S
[POWERPC] Fix up ibm_architecture_vec definition
[POWERPC] Make OF irq map code detect more error cases
[POWERPC] Support for "weird" MPICs and fixup mpc7448_hpc2
[POWERPC] Fix MPIC sense codes in documentation
[POWERPC] Fix performance regression in IRQ radix tree locking
[POWERPC] Add mpc7448hpc2 device tree source file
[POWERPC] Add MPC8349E MDS device tree source file to arch/powerpc/boot/dts
[POWERPC] modify mpc83xx platforms to use new IRQ layer
[POWERPC] Adapt ipic driver to new host_ops interface, add set_irq_type to set IRQ sense
[POWERPC] back up old school ipic.[hc] to arch/ppc
[POWERPC] Use mpc8641hpcn PIC base address from dev tree.
[POWERPC] Allow MPC8641 HPCN to build with CONFIG_PCI disabled too.
[POWERPC] Fix powerpc 44x_mmu build
[POWERPC] Remove flush_dcache_all export
As a replacement for the earlier removal of the e820 MCFG check
we blacklist the Intel SDV with the original BIOS bug that
motivated that check. On those machines don't use MMCONFIG.
This also adds a new pci=mmconf parameter to override the blacklist.
Cc: Greg KH <gregkh@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The booting-without-of.txt had incorrect definition for the sense codes
for an OpenPIC controller
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the end point of the separate aic94xx driver based on the
original driver and transport class from Luben Tuikov
<ltuikov@yahoo.com>
The log of the separate development is:
Alexis Bruemmer:
o aic94xx: fix hotplug/unplug for expanderless systems
o aic94xx: disable split completion timer/setting by default
o aic94xx: wide port off expander support
o aic94xx: remove various inline functions
o aic94xx: use bitops
o aic94xx: remove queue comment
o aic94xx: remove sas_common.c
o aic94xx: sas remove depot's
o aic94xx: use available list_for_each_entry_safe_reverse()
o aic94xx: sas header file merge
James Bottomley:
o aic94xx: fix TF_TMF_NO_CTX processing
o aic94xx: convert to request_firmware interface
o aic94xx: fix hotplug/unplug
o aic94xx: add link error counts to the expander phys
o aic94xx: add transport class phy reset capability
o aic94xx: remove local_attached flag
o Remove README
o Fixup Makefile variable for libsas rename
o Rename sas->libsas
o aic94xx: correct return code for sas_discover_event
o aic94xx: use parent backlink port
o aic94xx: remove channel abstraction
o aic94xx: fix routing algorithms
o aic94xx: add backlink port
o aic94xx: fix cascaded expander properties
o aic94xx: fix sleep under lock
o aic94xx: fix panic on module removal in complex topology
o aic94xx: make use of the new sas_port
o rename sas_port to asd_sas_port
o Fix for eh_strategy_handler move
o aic94xx: move entirely over to correct transport class formulation
o remove last vestages of sas_rphy_alloc()
o update for eh_timed_out move
o Preliminary expander support for aic94xx
o sas: remove event thread
o minor warning cleanups
o remove last vestiges of id mapping arrays
o Further updates
o Convert aic94xx over entirely to the transport class end device and
o update aic94xx/sas to use the new sas transport class end device
o [PATCH] aic94xx: attaching to the sas transport class
o Add missing completion removal from prior patch
o [PATCH] aic94xx: attaching to the sas transport class
o Build fixes from akpm
Jeff Garzik:
o [scsi aic94xx] Remove ->owner from PCI info table
Luben Tuikov:
o initial aic94xx driver
Mike Anderson:
o aic94xx: fix panic on module insertion
o aic94xx: stub out SATA_DEV case
o aic94xx: compile warning cleanups
o aic94xx: sas_alloc_task
o aic94xx: ref count update
o aic94xx nexus loss time value
o [PATCH] aic94xx: driver assertion in non-x86 BIOS env
Randy Dunlap:
o libsas: externs not needed
Robert Tarte:
o aic94xx: sequence patch - fixes SATA support
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change the list of cpus allowed to tasks in the top (root) cpuset to
dynamically track what cpus are online, using a CPU hotplug notifier. Make
this top cpus file read-only.
On systems that have cpusets configured in their kernel, but that aren't
actively using cpusets (for some distros, this covers the majority of
systems) all tasks end up in the top cpuset.
If that system does support CPU hotplug, then these tasks cannot make use
of CPUs that are added after system boot, because the CPUs are not allowed
in the top cpuset. This is a surprising regression over earlier kernels
that didn't have cpusets enabled.
In order to keep the behaviour of cpusets consistent between systems
actively making use of them and systems not using them, this patch changes
the behaviour of the 'cpus' file in the top (root) cpuset, making it read
only, and making it automatically track the value of cpu_online_map. Thus
tasks in the top cpuset will have automatic use of hot plugged CPUs allowed
by their cpuset.
Thanks to Anton Blanchard and Nathan Lynch for reporting this problem,
driving the fix, and earlier versions of this patch.
Signed-off-by: Paul Jackson <pj@sgi.com>
Cc: Nathan Lynch <ntl@pobox.com>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's updated documentation for the relay interface, rewritten to match
the relayfs->relay changes. It also moves relayfs.txt to relay.txt in the
process.
It includes the changes to relayfs.txt previously posted by Randy Dunlap,
thanks for those.
The relay-apps examples have also been updated to match, and can be found
on the sourceforge relayfs website.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sergey Vlasov noticed that there is not kernel.suid_dumpable, but
fs.suid_dumpable.
How KERN_SETUID_DUMPABLE ended up in fs_table[]? Hell knows...
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was asked several times to include userspace example code into
Documentation, so if there is no policy against it, consider attached patch
for 2.6.18. This program works with included Documentation/connector/cn_test.c
connector module.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since libata moved from /drivers/scsi to /drivers/ata this template is broken.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
According to drivers/video/intelfb/intelfb.h, the intelfb driver
supportes the following devices:
830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM. So the description in
drivers/video/Kconfig and the documentation in
Documentation/fb/intelfb.txt is outdated.
airlied: cleaned up some other obvious mistakes in intelfb.txt.
Signed-off-by: Christian Merkle <mail@christian-merkle.de>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Also accept "local-mac-address". However the old "address"
is now obsolete, but accepted for backwards compatibility.
It should be removed after all device trees have been
converted to use "mac-address".
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
this minor patch fixes the description of net.ipv4.tcp_mem sysctl
in ip-sysctl.txt - the headline names the values "min, pressure, max",
while the description uses the "low, pressure, high" values.
Both tcp_rmem and tcp_wmem descriptions use the "min, pressure, max"
values, so I have changed the tcp_mem to match this and not vice versa.
Signed-off-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic Machine detection to imacfb and some Ducumentation bits for
imacfb.
Signed-off-by: Edgar Hucek <hostmaster@ed-soft.at>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Conflicts:
arch/ia64/hp/sim/simscsi.c
Stylistic differences in two separate fixes for buffer->request_buffer
problem.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Propagate acpi_processor_preregister_performance return value.
[CPUFREQ] [2/2] demand load governor modules.
[CPUFREQ] [1/2] add __find_governor helper and clean up some error handling.
[CPUFREQ] Longhaul - Rename & fix multipliers table
[CPUFREQ] Longhaul - Fix power state test to do something more useful
[CPUFREQ] Longhaul - Readd accidentally dropped line
[CPUFREQ] Make longhaul_walk_callback() static
[CPUFREQ] X86_GX_SUSPMOD must depend on PCI
[CPUFREQ] Longhaul - Initialise later.
[CPUFREQ] Longhaul - Workaround issues with APIC.
[CPUFREQ] Longhaul - Hook into ACPI C states.
[CPUFREQ] return error when failing to set minfreq
Remove references to the IPoIB IETF working group as it has been closed.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I just stumbled on this bug/feature, this is how to reproduce it:
# echo 450000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
# echo 450000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
# echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
# cpufreq-info -p
450000 450000 powersave
# echo 1800000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq ; echo $?
0
# cpufreq-info -p
450000 450000 powersave
Here it is. The kernel refuses to set a min_freq higher than the
max_freq but it allows a max_freq lower than min_freq (lowering min_freq
also).
This behaviour is pretty straightforward (but undocumented) and it
doesn't return an error altough failing to accomplish the requested
action (set min_freq).
The problem (IMO) is basically that userspace is not allowed to set a
full policy atomically while the kernel always does that thus it must
enforce an ordering on operations.
The attached patch returns -EINVAL if trying to increase frequencies
starting from scaling_min_freq and documents the correct ordering of writes.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Dominik Brodowski <linux at dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
--
I spent a long time the other day trying to examine an initrd image on a
fedora core 5 system because the initrd.txt file is apparently obsolete.
Here is a patch which I hope will reduce future confusion for others.
Signed-off-by: Thomas Horsley <tom.horsley@ccur.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The latest toolchains can produce a new ELF section in DSOs and
dynamically-linked executables. The new section ".gnu.hash" replaces
".hash", and allows for more efficient runtime symbol lookups by the
dynamic linker. The new ld option --hash-style={sysv|gnu|both} controls
whether to produce the old ".hash", the new ".gnu.hash", or both. In some
new systems such as Fedora Core 6, gcc by default passes --hash-style=gnu
to the linker, so that a standard invocation of "gcc -shared" results in
producing a DSO with only ".gnu.hash". The new ".gnu.hash" sections need
to be dealt with the same way as ".hash" sections in all respects; only the
dynamic linker cares about their contents. To work with older dynamic
linkers (i.e. preexisting releases of glibc), a binary must have the old
".hash" section. The --hash-style=both option produces binaries that a new
dynamic linker can use more efficiently, but an old dynamic linker can
still handle.
The new section runs afoul of the custom linker scripts used to build vDSO
images for the kernel. On ia64, the failure mode for this is a boot-time
panic because the vDSO's PT_IA_64_UNWIND segment winds up ill-formed.
This patch addresses the problem in two ways.
First, it mentions ".gnu.hash" in all the linker scripts alongside ".hash".
This produces correct vDSO images with --hash-style=sysv (or old tools),
with --hash-style=gnu, or with --hash-style=both.
Second, it passes the --hash-style=sysv option when building the vDSO
images, so that ".gnu.hash" is not actually produced. This is the most
conservative choice for compatibility with any old userland. There is some
concern that some ancient glibc builds (though not any known old production
system) might choke on --hash-style=both binaries. The optimizations
provided by the new style of hash section do not really matter for a DSO
with a tiny number of symbols, as the vDSO has. If someone wants to use
=gnu or =both for their vDSO builds and worry less about that
compatibility, just change the option and the linker script changes will
make any choice work fine.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change "Thrid" into "Third", and realign similarly to other entries.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: <device@lanana.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few cleanups to SubmittingPatches:
- mention SubmitChecklist
- remove mention of my simple patch script tools
- remove last-updated line
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kernel/workqueue.c was omitted from generating kernel documentation. This
adds a new section "Workqueues and Kevents" and adds documentation for some
of the functions.
Some functions in this file already had DocBook-style comments, now they
finally become visible.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up kernel-doc comments in drivers/pci/search.c (line sizes and typos).
Enable that source file in DocBook/kernel-api.tmpl.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
insert_resource() was unexported, so kernel-doc needs to be told to search
kernel/resource.c for internal functions instead of exported functions so that
it won't report an error.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update hotplug cpu documentation to clearly state when to use
register_cpu_notifier() and register_hotcpu_notifier.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable delay accounting by default so that feature gets coverage testing
without requiring special measures.
Earlier, it was off by default and had to be enabled via a boot time param.
This patch reverses the default behaviour to improve coverage testing. It
can be removed late in the kernel development cycle if its believed users
shouldn't have to incur any cost if they don't want delay accounting. Or
it can be retained forever if the utility of the stats is deemed common
enough to warrant keeping the feature on.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a complementary network driver for our ISP4XXX parts.
There is a concurrent effort underway to get the iSCSI driver (qla4xxx)
integrated upstream as well.
I have been through several iterations with the linux-netdev list and have had
much response from Stephen Hemminger.
- Built and tested using kernel 2.6.17-rc4.
- The chip supports two ethernet and two iSCSI functions.
- The functions ql_sem_lock, ql_sem_spinlock, ql_sem_unlock, and
ql_wait_for_drvr_lock are used to protect resources that are shared across
the network and iSCSI functions. This protection is mostly during chip
initialization and resets, but also include link management.
- The PHY/MII are not exported through ethtool due to the fact that the
iSCSI function will control the common link at least 50% of the time.
This driver has been through several iterations on the netdev list and we feel
this driver is ready for inclusion in the upstream kernel.
It has been built and tested on x86 and PPC64 platforms.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
arcmsr is a driver for the Areca Raid controller, a host based RAID
subsystem that speaks SCSI at the firmware level.
This patch is quite a clean up over the initial submission with
contributions from:
Randy Dunlap <rdunlap@xenotime.net>
Christoph Hellwig <hch@lst.de>
Matthew Wilcox <matthew@wil.cx>
Adrian Bunk <bunk@stusta.de>
Signed-off-by: Erich Chen <erich@areca.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There was an issue in the data structure defined by megaraid driver
casuing "kernel unaligned access.." messages to be displayed during
IOCTL on IA64 platform.
The issue has been reported/fixed by Sakurai Hiroomi
[sakurai_hiro@soft.fujitsu.com].
Signed-Off By: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With this patch, driver will protect data corruption created by
INQUIRY with EVPD request to megaraid controllers. As specified in
the changelog, megaraid F/W already has fixed the issue and being
under process of release. Meanwhile, driver will protect the system
with this patch.
Signed-Off By: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains
- a fix for 64-bit DMA capability check in megaraid_{mm,mbox} driver.
- includes changes (going back to 32-bit DMA mask if 64-bit DMA mask
failes) suggested by James with previous patch.
- addition of SATA 150-4/6 as commented by Vasily Averin.
With patch, the driver access PCIconfiguration space with dedicated
offset to read a signature. If the signature read, it means that the
controller has capability to handle 64-bit DMA.
Without this patch, the driver used to blindly claim 64-bit DMA
capability.
The issue has been reported by Vasily Averin [vvs@sw.ru].
Thank you Vasily for the reporting.
Signed-Off By: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add bridge netfilter deferred output hooks to feature-removal-schedule
and disable them by default. Until their removal they will be
activated by the physdev match when needed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the reference to set_wmb from memory-barriers.txt
since it shouldn't be used.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change documentation and example program to reflect the flow control issues
being addressed by the cpumask changes.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Send per-tgid data only once during exit of a thread group instead of once
with each member thread exit.
Currently, when a thread exits, besides its per-tid data, the per-tgid data
of its thread group is also sent out, if its thread group is non-empty.
The per-tgid data sent consists of the sum of per-tid stats for all
*remaining* threads of the thread group.
This patch modifies this sending in two ways:
- the per-tgid data is sent only when the last thread of a thread group
exits. This cuts down heavily on the overhead of sending/receiving
per-tgid data, especially when other exploiters of the taskstats
interface aren't interested in per-tgid stats
- the semantics of the per-tgid data sent are changed. Instead of being
the sum of per-tid data for remaining threads, the value now sent is the
true total accumalated statistics for all threads that are/were part of
the thread group.
The patch also addresses a minor issue where failure of one accounting
subsystem to fill in the taskstats structure was causing the send of
taskstats to not be sent at all.
The patch has been tested for stability and run cerberus for over 4 hours
on an SMP.
[akpm@osdl.org: bugfixes]
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a "taskstats" interface based on generic netlink (NETLINK_GENERIC
family), for getting statistics of tasks and thread groups during their
lifetime and when they exit. The interface is intended for use by multiple
accounting packages though it is being created in the context of delay
accounting.
This patch creates the interface without populating the fields of the data
that is sent to the user in response to a command or upon the exit of a task.
Each accounting package interested in using taskstats has to provide an
additional patch to add its stats to the common structure.
[akpm@osdl.org: cleanups, Kconfig fix]
Signed-off-by: Shailabh Nagar <nagar@us.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initialization code related to collection of per-task "delay" statistics which
measure how long it had to wait for cpu, sync block io, swapping etc. The
collection of statistics and the interface are in other patches. This patch
sets up the data structures and allows the statistics collection to be
disabled through a kernel boot parameter.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pci_dac_set_dma_mask() gives only a single match in the whole kernel tree
and that's in this doc file. The best candidate for replacement is
pci_dac_dma_supported().
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Greg KH <greg@kroah.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The default ramdisk blocksize is actually 1024, not 512 bytes. Also fixes
up some trailing whitespace issues.
Signed-off-by: Nathan Scott <nathans@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* HEAD:
[PATCH] hwmon: Documentation update for abituguru
[PATCH] hwmon: Fix for first generation Abit uGuru chips
[PATCH] hwmon: New maintainer for w83791d
[PATCH] pca9539: Honor the force parameter
[PATCH] i2c-algo-bit: Wipe out dead code
[PATCH] i2c: Handle i2c_add_adapter failure in i2c algorithm drivers
[PATCH] i2c: New mailing list
[PATCH] i2c-ite: Plan for removal
[PATCH] i2c-powermac: Fix master_xfer return value
[PATCH] scx200_acb: Fix the block transactions
[PATCH] scx200_acb: Fix the state machine
[PATCH] i2c-iop3xx: Avoid addressing self
[PATCH] i2c: Fix 'ignore' module parameter handling in i2c-core
Implement the scheduled unexport of insert_resource.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Text from the back of the box, for your information/amusement:
USB DATA CABLE
FOR K700 Series
The USB Cable is an ideal link between your mobile phone and PC. Employing
the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions
such as synchronization of phone book and calendar,as well as Internet browsing via
a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity.
MADE IN CHINA
From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation update for the new bank1_types module param.
Also add what we know about different revisions of the uGuru and
a note that the abituguru driver unfortunatly does not work with the
latest and greatest motherboards, which have what I think is revision
4 of the uGuru.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have a new mailing list dedicated to linux i2c:
http://lists.lm-sensors.org/mailman/listinfo/i2c
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Plan the i2c-ite and i2c-algo-ite drivers for removal.
These drivers never compiled since they were added to the kernel
tree 5 years ago. Also see:
http://marc.theaimsgroup.com/?l=linux-mips&m=115040510817448
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed 'section mismatch' errors in ALSA PCI drivers:
- removed invalid __devinitdata from pci id tables
- fix/remove __devinit of functions called in suspend/resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Update Documentation/SubmitChecklist.
- Mention lockdep coverage
- Describe documentation requirements
- Number the various items to simplify the composition of caustic emails.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As announced half a year ago this patch will remove the tasklist_lock
export. The previous two patches got rid of the remaining modular users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When EDAC was first introduced into the kernel it had a sysfs interface,
but due to some problems it was disabled in 2.6.16 and remained disabled in
2.6.17.
With feedback, several of the control and attribute files of that interface
had some good constructive feedback. PCI Blacklist/Whitelist was a major
set which has design issues and it has been removed in this patch. Instead
of storing PCI broken parity status in EDAC, it has been moved to the
pci_dev structure itself by a previous PCI patch. A future patch will
enable that feature in EDAC by utilizing the pci_dev info.
The sysfs is now enabled in this patch, with a minimal set of control and
attribute files for examining EDAC state and for enabling/disabling the
memory and PCI operations.
The Documentation for EDAC has also been updated to reflect the new state
of EDAC operation.
Signed-off-by:Doug Thompson <norsk5@xmisson.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As I was looking over the get_sb() changes, I stumbled across a little
mistake in the documentation updates. Unless we're getting into an
interesting new object-oriented realm, I doubt that get_sb() should really
return "struct int"...
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updater should use _rcu variant of list_del().
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Acked-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Document the ip command a little differently to make the
interaction between defaults and autoconfiguration a little clearer
(I hope)
* Update autoconfiguration the current set of options, including DHCP
* Update the boot methods to add syslinux and isolinux, and remove
dd of=/dev/fd0 which is no longer supported by linux
* Add a referance to initramfs along side initrd.
Should the latter and its document be removed some time soon?
* Various cleanups to put the text consistently into the thrid person
* Reformated a bit to fit into 80 columns a bit more nicely
* Should the bootloaders documentation be removed or split
into a separate documentation, it seems somewhat out of scope
Signed-off-by: Horms <horms@verge.net.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
[Bluetooth] Add RFCOMM role switch support
[Bluetooth] Allow disabling of credit based flow control
[Bluetooth] Small cleanup of the L2CAP source code
[Bluetooth] Use real devices for host controllers
[Bluetooth] Add platform device for virtual and serial devices
[Bluetooth] Add automatic sniff mode support
[Bluetooth] Correct SCO buffer size on request
[Bluetooth] Add suspend/resume support to the HCI USB driver
[Bluetooth] Use raw mode for the Frontline sniffer device
[BRIDGE]: br_dump_ifinfo index fix
[ATM]: add+use poison defines
[NET]: add+use poison defines
[IOAT]: fix kernel-doc in source files
[IOAT]: fix header file kernel-doc
[TG3]: Add ipv6 TSO feature
[IPV6]: Fix ipv6 GSO payload length
[TIPC] Fixed sk_buff panic caused by tipc_link_bundle_buf (REVISED)
[NET]: Verify gso_type too in gso_segment
[IPVS]: Add sysctl documentation
[ROSE]: Try all routes when establishing a ROSE connections.
...
* Derived from http://www.linuxvirtualserver.org/docs/sysctl.html, v1.4
maintained by Wensong Zhang
* Adjusted preample to match ip-sysctl.txt
* Sorted options into alphabetical order
* Added expire_quiescent_template
* Removed timeout_* which are no longer present
* Incoporated doc/debug-levels.txt from IPVS source tree into
description of ipvs_debug
* Minor spelling fixes
* Further editing more than welcome
Signed-Off-By: Horms <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: add defconfig for Freescale MPC8349E-mITX board
powerpc: Add base support for the Freescale MPC8349E-mITX eval board
Documentation: correct values in MPC8548E SEC example node
[POWERPC] Actually copy over i8259.c to arch/ppc/syslib this time
[POWERPC] Add new interrupt mapping core and change platforms to use it
[POWERPC] Copy i8259 code back to arch/ppc
[POWERPC] New device-tree interrupt parsing code
[POWERPC] Use the genirq framework
[PATCH] genirq: Allow fasteoi handler to retrigger disabled interrupts
[POWERPC] Update the SWIM3 (powermac) floppy driver
[POWERPC] Fix error handling in detecting legacy serial ports
[POWERPC] Fix booting on Momentum "Apache" board (a Maple derivative)
[POWERPC] Fix various offb and BootX-related issues
[POWERPC] Add a default config for 32-bit CHRP machines
[POWERPC] fix implicit declaration on cell.
[POWERPC] change get_property to return void *
Introduce DEBUG_LOCKING_API_SELFTESTS, which uses the generic lock debugging
code's silent-failure feature to run a matrix of testcases. There are 210
testcases currently:
+-----------------------
| Locking API testsuite:
+------------------------------+------+------+------+------+------+------+
| spin |wlock |rlock |mutex | wsem | rsem |
-------------------------------+------+------+------+------+------+------+
A-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-B-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok |
A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok |
double unlock: ok | ok | ok | ok | ok | ok |
bad unlock order: ok | ok | ok | ok | ok | ok |
--------------------------------------+------+------+------+------+------+
recursive read-lock: | ok | | ok |
--------------------------------------+------+------+------+------+------+
non-nested unlock: ok | ok | ok | ok |
--------------------------------------+------+------+------+
hard-irqs-on + irq-safe-A/12: ok | ok | ok |
soft-irqs-on + irq-safe-A/12: ok | ok | ok |
hard-irqs-on + irq-safe-A/21: ok | ok | ok |
soft-irqs-on + irq-safe-A/21: ok | ok | ok |
sirq-safe-A => hirqs-on/12: ok | ok | ok |
sirq-safe-A => hirqs-on/21: ok | ok | ok |
hard-safe-A + irqs-on/12: ok | ok | ok |
soft-safe-A + irqs-on/12: ok | ok | ok |
hard-safe-A + irqs-on/21: ok | ok | ok |
soft-safe-A + irqs-on/21: ok | ok | ok |
hard-safe-A + unsafe-B #1/123: ok | ok | ok |
soft-safe-A + unsafe-B #1/123: ok | ok | ok |
hard-safe-A + unsafe-B #1/132: ok | ok | ok |
soft-safe-A + unsafe-B #1/132: ok | ok | ok |
hard-safe-A + unsafe-B #1/213: ok | ok | ok |
soft-safe-A + unsafe-B #1/213: ok | ok | ok |
hard-safe-A + unsafe-B #1/231: ok | ok | ok |
soft-safe-A + unsafe-B #1/231: ok | ok | ok |
hard-safe-A + unsafe-B #1/312: ok | ok | ok |
soft-safe-A + unsafe-B #1/312: ok | ok | ok |
hard-safe-A + unsafe-B #1/321: ok | ok | ok |
soft-safe-A + unsafe-B #1/321: ok | ok | ok |
hard-safe-A + unsafe-B #2/123: ok | ok | ok |
soft-safe-A + unsafe-B #2/123: ok | ok | ok |
hard-safe-A + unsafe-B #2/132: ok | ok | ok |
soft-safe-A + unsafe-B #2/132: ok | ok | ok |
hard-safe-A + unsafe-B #2/213: ok | ok | ok |
soft-safe-A + unsafe-B #2/213: ok | ok | ok |
hard-safe-A + unsafe-B #2/231: ok | ok | ok |
soft-safe-A + unsafe-B #2/231: ok | ok | ok |
hard-safe-A + unsafe-B #2/312: ok | ok | ok |
soft-safe-A + unsafe-B #2/312: ok | ok | ok |
hard-safe-A + unsafe-B #2/321: ok | ok | ok |
soft-safe-A + unsafe-B #2/321: ok | ok | ok |
hard-irq lock-inversion/123: ok | ok | ok |
soft-irq lock-inversion/123: ok | ok | ok |
hard-irq lock-inversion/132: ok | ok | ok |
soft-irq lock-inversion/132: ok | ok | ok |
hard-irq lock-inversion/213: ok | ok | ok |
soft-irq lock-inversion/213: ok | ok | ok |
hard-irq lock-inversion/231: ok | ok | ok |
soft-irq lock-inversion/231: ok | ok | ok |
hard-irq lock-inversion/312: ok | ok | ok |
soft-irq lock-inversion/312: ok | ok | ok |
hard-irq lock-inversion/321: ok | ok | ok |
soft-irq lock-inversion/321: ok | ok | ok |
hard-irq read-recursion/123: ok |
soft-irq read-recursion/123: ok |
hard-irq read-recursion/132: ok |
soft-irq read-recursion/132: ok |
hard-irq read-recursion/213: ok |
soft-irq read-recursion/213: ok |
hard-irq read-recursion/231: ok |
soft-irq read-recursion/231: ok |
hard-irq read-recursion/312: ok |
soft-irq read-recursion/312: ok |
hard-irq read-recursion/321: ok |
soft-irq read-recursion/321: ok |
--------------------------------+-----+----------------
Good, all 210 testcases passed! |
--------------------------------+
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that it is advantageous to leave a small portion of unmapped file
backed pages if all of a zone's pages (or almost all pages) are allocated and
so the page allocator has to go off-node.
This allows recently used file I/O buffers to stay on the node and
reduces the times that zone reclaim is invoked if file I/O occurs
when we run out of memory in a zone.
The problem is that zone reclaim runs too frequently when the page cache is
used for file I/O (read write and therefore unmapped pages!) alone and we have
almost all pages of the zone allocated. Zone reclaim may remove 32 unmapped
pages. File I/O will use these pages for the next read/write requests and the
unmapped pages increase. After the zone has filled up again zone reclaim will
remove it again after only 32 pages. This cycle is too inefficient and there
are potentially too many zone reclaim cycles.
With the 1% boundary we may still remove all unmapped pages for file I/O in
zone reclaim pass. However. it will take a large number of read and writes
to get back to 1% again where we trigger zone reclaim again.
The zone reclaim 2.6.16/17 does not show this behavior because we have a 30
second timeout.
[akpm@osdl.org: rename the /proc file and the variable]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
