md->disk was being used in a debug message before it was allocated.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Backport the "pio flush" from the libata major update to 2.6.17 for via atapi.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The truncate threshold calculation to prevent receiver from getting stuck
was incorrect, and it didn't take into account the upper limit on bits
in the register so the jumbo packet support was broken.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At this point, the core QP structure hasn't been initialized, so what's
in there isn't valid. Get the same information elsewhere.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The problem was that node A's sending thread, which handles sending RDMA
read response data, would write the trigger word, the last packet would
be sent, node B would send a new RDMA read request, node A's interrupt
handler would initialize s_rdma_sge, then node A's sending thread would
update s_rdma_sge. This didn't happen very often naturally but was more
frequent with 1 byte RDMA reads. Rather than adding more locking or
increasing the QP structure size and copying sge data, I modified the
copy routine to update the pointers before writing the trigger word to
avoid the update race.
Signed-off-by: Ralph Campbell <ralphc@pathscale.com>
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixed so it works on the PE-800. It had not previously been updated to
match PE-800 receive interrupt differences from HT-400.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is required for even semi-decent performance on OpenIB.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix NULL deref due to pcidev being clobbered before dd->ipath_f_cleanup()
was called.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the interface version that gets exported to userspace.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make sure modify_qp won't modify the QP if any of the changes failed.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The local loopback path for RC can lock the rkey table lock without
blocking interrupts. The receive interrupt path can then call
ipath_rkey_ok() and deadlock. Remove the redundant lock.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
reference to .init.text: from .text between 'dvb_bt8xx_probe'
(at offset 0x122c) and 'dvb_bt8xx_remove'
reference to .init.text: from .text between 'dvb_bt8xx_probe'
(at offset 0x1267) and 'dvb_bt8xx_remove'
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If CONFIG_VIDEO_DEV=m and CONFIG_VIDEO_V4L1_COMPAT=y, v4l1-compat should
be built as a module (currently, it isn't built at all leading to
problems with modules using it).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the skb allocation fails, the current error path calls
dev_kfree_skb_irq() with a NULL argument. Also, 'err' is not being used.
Coverity CID: 275.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We still don't have the tty layer licensing compatibility quite right.
tty_insert_flip_char() used to be inlined in include/linux/tty_flip.h. It
is now out-of-lined and hence needs EXPORT_SYMBOL() to be back-compatible.
One known offender is the Intel Modem driver.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This loop that sets up the hash_table has problems.
Careful examination will show that the last time through, everything but
the first line is pointless. This is because all it does is change 'cur'
and 'size' and neither of these are used after the loop. This should ring
warning bells... That last time through the loop,
size += conf->strip_zone[cur].size
can index off the end of the strip_zone array. Depending on what it finds
there, it might exit the loop cleanly, or it might spin going further and
further beyond the array until it hits an unmapped address.
This patch rearranges the code so that the last, pointless, iteration of
the loop never happens. i.e. the one statement of the last loop that is
needed is moved the the end of the previous loop - or to before the loop
starts - and the loop counter starts from 1 instead of 0.
Cc: "Don Dupuis" <dondster@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use kmalloc() instead of a local array in bnx2_nvram_write().
Update version to 1.4.40.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug in bnx2_nvram_write() caused by a counter variable not
correctly incremented by 4.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some missing rx error counters for 5705 and newer chips.
Update version to 3.58.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables agpgart on a Via "PT880 Ultra" based motherboard
(Asus P4V800D-X). The PCI ID of the PT880 Ultra is 0x0308 instead of
0x0258 of the PT880.
The patched via-agp passes testgart.
Signed-off-by: Magnus Kessler <Magnus.Kessler@gmx.net>
Signed-off-by: Dave Jones <davej@redhat.com>
FATAL: modpost: GPL-incompatible module sunsu uses the GPL-only symbol tty_insert_flip_string_flags
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: drivers/video/i810/i810fb.o - Section mismatch: reference to .init.data: from .text between 'i810_fix_offsets' (at offset 0x1b88) and 'i810_alloc_agp_mem'
WARNING: drivers/video/i810/i810fb.o - Section mismatch: reference to .init.data: from .text between 'i810_fix_offsets' (at offset 0x1b8f) and 'i810_alloc_agp_mem'
WARNING: drivers/video/i810/i810fb.o - Section mismatch: reference to .init.data: from .text between 'i810_fix_offsets' (at offset 0x1ba3) and 'i810_alloc_agp_mem'
WARNING: drivers/video/i810/i810fb.o - Section mismatch: reference to .init.data: from .text between 'i810_fix_offsets' (at offset 0x1bb5) and 'i810_alloc_agp_mem'
WARNING: drivers/video/i810/i810fb.o - Section mismatch: reference to .init.data: from .text between 'i810_fix_offsets' (at offset 0x1bc6) and 'i810_alloc_agp_mem'
WARNING: drivers/video/i810/i810fb.o - Section mismatch: reference to .init.data: from .text between 'i810_init_defaults' (at offset 0x1dd8) and 'i810_init_device'
WARNING: drivers/video/i810/i810fb.o - Section mismatch: reference to .init.data: from .text between 'i810_init_defaults' (at offset 0x1dfb) and 'i810_init_device'
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Appropriately use -ENOIOCTLCMD and -ENOTTY when the ioctl is not
implemented by a driver.
(akpm: we're not allowed to return -ENOIOCTLCMD to userspace. This patch does
the right thing).
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some outstanding issues with the pxa2xx_spi driver when running on a
PXA270:
- Wrong timeout calculation in the setup function due to different
peripheral clock rates in the PXAxxx family.
- Bad handling of SSSR_TFS interrupts in interrupt_transfer function.
- Added locking to interface between the pump_messages workqueue and the
pump_transfers tasklet.
Much thanks to Juergen Beisert for the extensive testing on the PXA270.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hardware based SPI driver for Samsung S3C24XX SoC systems
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SPI driver for SPI by GPIO on the Samsung S3C24XX series of SoC processors.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- remove the following global function that is both unused and
unimplemented:
- register_firmware()
- make the following needlessly global function static:
- firmware_class_uevent()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver supports the SPI controller on the MPC83xx SoC devices from
Freescale. Note, this driver supports only the simple shift register SPI
controller and not the descriptor based CPM or QUICCEngine SPI controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because several developers asked me about referenced but missing
spi_add_master(), I think that this patch should be applied ... it
corrects comments so they refer to spi_register_master() instead.
Signed-off-by: dmitry pervushin <dpervushin@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes coverity bug id #1237. After the while loop, it is possible for
i == ISDN_LMSNLEN. If this happens the terminating '\0' is written after
the end of the array.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The OSC set and query functions do not allocate enough space for return
values, and set the output buffer length to a false, too large value. This
causes the acpi-ca code to assume that the output buffer is larger than it
actually is, and overwrite memory when copying acpi return buffers into
this caller provided buffer. In some cases this can cause kernel oops if
the memory that is overwritten is a pointer. This patch will change these
calls to use a dynamically allocated output buffer, thus allowing the
acpi-ca code to decide how much space is needed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: "Yu, Luming" <luming.yu@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make a read of a HID device block until data is available. Without it, the
read goes into a busy-wait loop until data is available.
Cc: Greg KH <greg@kroah.com>
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should be able to write 'repair' to /sys/block/mdX/md/sync_action,
however due to and inverted test, that always given EINVAL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like the generic ide code now wants ide_init_hwif_ports() to set
the parent struct device into the ide_hw structure (new field ?). Without
this, the mac ide code can cause the ide probing code to explode in flames
in sysfs registration due to what looks like a stale pointer in there
(happens when removing/re-inserting one of the hotswap media bays on some
laptops).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There has been a longstanding problem with the Matrox G450 and perhaps
other similar cards, with modes "above" 1280x1024-60 on ppc/ppc64 boxes
running Linux. Higher resolutions and/or higher refresh rates resulted in
a very noticably "jittery" display, and sometimes no display, depending on
the physical monitor. This patch fixes that problem on the systems I have
easy access to...
I've tested with SLES9SP3 (2.6.5+ kernel) and 2.6.16-rc6 custom kernels on
an IBM eServer p5 520 w/G450 (a.k.a GXT135P on IBM's ppc64 systems), and a
colleague of mine (Ian Romanick) tested it successfully on an Apple ppc32
box (w/GXT135P). I also tested it on IA32 box I have with a GXT135P to
verify that it didn't obviously break anything. In my testing, I covered
single-card, single and dual-head setups using both HD15 and DVI-D signals,
on both the IA32 and ppc64 boxes. While everything appeared fine on both
boxes, I did encounter one problem: I can't get any signal on the DVI-D
output on the ppc64 box. However, this is also the case without my patch.
I just noticed that screen-blanking only occurs on the primary display as
well.
Signed-off-by: Paul A. Clarke <pc@us.ibm.com>
Signed-off-by: Ian Romanick <idr@us.ibm.com>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Manfred Spraul <manfred@colorfullife.com> and
Andrew Morton <akpm@osdl.org>
Bring back this recently-reverted patch, only fixed.
Original changelog:
From: Ayaz Abdulla <aabdulla@nvidia.com>
This patch fixes the issues with multiple irqs.
I am resending based on feedback. I decoupled the dma mask for
consistent memory and fixed leak with multiple irq in error path.
Thanks to Manfred for catching the spin lock problem.
Fix it:
From: Manfred Spraul <manfred@colorfullife.com>
Fix bug introduced by ebf34c9b6f, covered in
http://bugzilla.kernel.org/show_bug.cgi?id=6568.
Remove second instance of the request_irq() calls: they were moved
from nv_open into nv_request_irq.
Thanks to Alistair Strachan <alistair@devzero.co.uk> for reporting and
persisting.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple write attributes in sas transport layer have a small
bug that prevents them from being written to. Those
attributes are the link_reset and write_reset. This is due
the store field being set to NULL.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
the user_scan() callback currently has the potential to identify the
wrong device in the presence of expanders. This is because it finds
the first device with a matching target_id, which might be an
expander. Fix this by making it look specifically for end devices.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fixes a byte-swap issue on PPC, found by Zang Roy-r61911
on the powerpc platform. His original patch also had some other
platform-specific changes in #ifdef's, but I'm not sure yet how to
incorporate them. Look for another patch for those (soon).
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver currently keeps local copies of the hardware request/response queue indexes.
But it expends significant effort ensuring consistency between the two views,
and still gets it wrong after an error or reset occurs.
This patch removes the local copies, in favour of just accessing the hardware
whenever we need them. Eventually this may need to be tweaked again for NCQ,
but for now this works and solves problems some users were seeing.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 60xx chips, and possibly others, incorrectly assert DEV_IRQ interrupts
on a regular basis. The cause of this is under investigation (by me and
in theory by Marvell also), but regardless we do need to deal with these events.
This patch tidies up some interrupt handler code, and ensures that we ignore
DEV_IRQ interrupts when the drive still has ATA_BUSY asserted.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The interface control register of the 60xx (and later) Marvell chip
requires certain bits to always be set when writing to it. These bits
incorrectly read-back as zeros, so the pattern must be ORed in
with each write of the register. Also, bit 12 should NOT be set
(note that Marvell's own driver also had bit-12 wrong here).
While we're at it, we also now do pci_set_master() in the init code.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some systems, it is possible that the BIOS may have enabled interrupt coalescing
for the Marvell controllers which support it. This patch adds code to detect/ack
interrupts from the chip's coalescing (combing) logic.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mv_err_intr() function is invoked from the driver's interrupt handler,
as well as from the timeout function. This patch prevents it from triggering
a one-after-the-other double reset of the controller when invoked
from the timeout function.
This also adds a check for a timeout race condition that has been observed
to occur with this driver in earlier kernels. This should not be needed,
in theory, but in practice it has caught bugs. Maybe nuke it at a later date.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Call pci_map_single() with the actual size of the receive
buffers, not 0 (which skb->len is initialized to by dev_alloc_skb()).
Signed-off-by: Erling A. Jacobsen <linuxcub@email.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver will get stuck (permanent transmit timeout), if the transmit
ring size is set too small. It needs to have enough ring elements to
hold one maximum size transmit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Skge driver always causes bad checksums on big-endian.
The checksum in the receive control block was being swapped
when it doesn't need to be.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the status ring processing can't keep up with the incoming frames,
it is more efficient to have NAPI keep scheduling the poll routine
rather than causing another interrupt.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Logic error in the phy initialization code. Also, turn on wake on lan
bit in status control.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.
Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If both ports are receiving on the SysKonnect dual port cards,
then it appears the bus interface unit can give an interrupt status
for frame before DMA has completed. This leads to bogus frames
and general confusion. This is why receive checksumming is also
messed up on dual port cards.
A workaround for the out of order receive problem is to eliminating
split transactions on PCI-X.
This version is based of the current linux-2.6.git including earlier
patch to disable dual ports.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revert previous patch with subject "change mdelay to msleep and remove
from ISR path". This patch seems to have caused bigger problems than
it solved, and it didn't solve much of a problem to begin with...
Discussion about backing-out this patch can be found here:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114321570402396&w=2
The git commit associated w/ the original patch is:
6ba98d311d
Signed-off-by: John W. Linville <linville@tuxdriver.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revert ebf34c9b6f. Maybe. Due to crashes
at shutdown - see http://bugzilla.kernel.org/show_bug.cgi?id=6568.
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Fix posting lists of 256 receive requests for Tavor
IB/uverbs: Don't leak ref to mm on error path
IB/srp: Complete correct SCSI commands on device reset
IB/srp: Get rid of extra scsi_host_put()s if reconnection fails
IB/srp: Don't wait for disconnection if sending DREQ fails
IB/mthca: Make fw_cmd_doorbell default to 0
ppa cannot handle highmem pages, and like imm, which already has
this patch, the device is slow, so performance is not a big issue,
so just force pages to be in low memory (hence mapped).
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
All registered reset callback handlers are called during reset processing.
The mptspi modules has its own reset callback handler, just recently
added for issuing domain validation after host reset. If either the mptsas or
mptfc driver are loaded, this callback could be called. Thus resulting
in domain validation being issued for sas or fibre end devices.
Fix this by having mptbase.c check the bus type against the driver
type and only call the reset handler if they match (or if it's a
non-bus specific reset handler).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
after upgrading our SUN E250 from 2.4 to 2.6 I'm seeing following error
when the HP DDS4 DAT changer gets probed:
scsi: host 1 channel 0 id 5 lun16777216 has a LUN larger than allowed by
the host adapter
The device is connected to a symbios 875 host. I've talked to Willy
about the problem, and he asked me to try to blacklist the device
for reportlun. I did that with the patch below and it solved the
problem. It now gets properly detected:
target1:0:5: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16)
Vendor: HP Model: C5713A Rev: H307
Type: Sequential-Access ANSI SCSI revision: 03
target1:0:5: Beginning Domain Validation
target1:0:5: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 16)
target1:0:5: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16)
target1:0:5: Domain Validation skipping write tests
target1:0:5: Ending Domain Validation
Vendor: HP Model: C5713A Rev: H307
Type: Medium Changer ANSI SCSI revision: 03
Signed-off-by: tsbogend@alpha.franken.de
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Pavel Pisa
There has been problems that for some paths that clock are not stopped
during new command programming and initiation. Result is issuing
of incorrect command to the card. Some other problems are cleaned too.
Noisy report of known ERRATUM #4 has been suppressed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we post a list of length 256 exactly, nreq in doorbell gets set to
256 which is wrong: it should be encoded by 0. This is because we
only zero it out on the next WR, which may not be there. The solution
is to ring the doorbell after posting a WQE, not before posting the
next one.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In ib_umem_release_on_close(), if the kmalloc() fails, then a
reference to current->mm will be leaked. Fix this by adding a mmput()
instead of just returning on kmalloc() failure.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Re-enable posted writes for status FIFO.
Besides bringing back a very minor bandwidth tweak from Linux 2.6.15.x
and older, this also fixes an interoperability regression since 2.6.16:
http://bugzilla.kernel.org/show_bug.cgi?id=6356
(sbp2: scsi_add_device failed. IEEE1394 HD is not working anymore.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Vanei Heidemann <linux@javanei.com.br>
Tested-by: Martin Putzlocher <mputzi@gmx.de> (chip type unconfirmed)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In case the blacklist with workarounds for device bugs yields a false
positive, the module load parameter can now also be used as an override
instead of an addition to the blacklist.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apple decided to copy some USB stupidity over to FireWire.
The sector number returned by iPods from read_capacity is one too many.
This may cause I/O errors, especially if the kernel is configured for EFI
partition support. We use the same workaround as usb-storage but have to
check for different model IDs.
http://marc.theaimsgroup.com/?t=114233262300001https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=187409
Acknowledgements:
Diagnosis and therapy by Mathieu Chouquet-Stringer <ml2news@free.fr>,
additional data about affected and unaffected Apple hardware from
Vladimir Kotal, Sander De Graaf, Bryan Olmstead and Hugh Dixon.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Grand unification of the three types of workarounds we have so far.
The "skip mode page 8" workaround is now limited to devices which
pretend to be of TYPE_DISK instead of TYPE_RBC. This workaround is no
longer enabled for Initio bridges.
Patch update in anticipation of more workarounds:
- Add module parameter "workarounds".
- Deprecate parameter "force_inquiry_hack".
- Compose the blacklist of a compound type for better readability and
extensibility.
- Remove a now unused #define.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/netdev-2.6:
sky2: prevent dual port receiver problems
x86_64: Check for bad dma address in b44 1GB DMA workaround
The ixp2000 driver for the enp2611 was developed on a board with
I still need this hack to work around the fact that softmac doesn't
attempt to associate when we bring the device up...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When flushing out queued commands after a successful device reset,
make sure that SRP completes the right commands, instead of calling
scsi_done on the command passed into the device reset handler over and
over.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a reconnection attempt fails, then SRP does two scsi_host_put()s.
This is a historical relic from an earlier version of the driver that
took a reference on the scsi_host before trying to reconnect, so get
rid of the extra scsi_host_put().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sending a DREQ may fail, for example because the remote target has
already broken the connection. If so, then SRP should not wait for
the disconnection to complete, because it never will.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Setting fw_cmd_doorbell allows FW command to be queued using posted
writes instead of requiring polling on a "go" bit, so it should be a
performance boost. However, the option causes problems with at least
some device/firmware combinations, so set the default to 0 until we
understand what's going on better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes two problems triggered by the MMC stack updating clocks:
- SPI masters driver should accept a max clock speed of zero; that's one
convention for marking idle devices. (Presumably that helps controllers
that don't autogate clocks to "off" when not in use.)
- There are more than 1000 nanoseconds per millisecond; setting the clock
down to 125 KHz now works properly.
Showing once again that Zero (http://en.wikipedia.org/wiki/Zero) is still
an inexhaustible number of bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix two outstanding issues with the pxa2xx_spi driver:
1) Bad cast in the function u32_writer. Thanks to Henrik Bechmann
2) Adds support for per transfer changes to speed and bits per word
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to be able to have a "SPI bus 0" matching chip numbering; but
that number was wrongly used to flag dynamic allocation of a bus number.
This patch resolves that issue; now negative numbers trigger dynamic alloc.
It also updates the how-to-write-a-controller-driver overview to mention
this stuff.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add spi_device hook for LSB-first word encoding, and update all the
(in-tree) controller drivers to reject such devices. Eventually,
some controller drivers will be updated to support lsb-first encodings
on the wire; no current drivers need this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renamed bitbang_transfer_setup to follow convention of other exported symbols
from spi-bitbang. Exported spi_bitbang_setup_transfer to allow users of
spi-bitbang to use the function in their own setup_transfer.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that spi_write_then_read() can always handle at least 32 bytes
of transfer (total, both directions), minimizing one portability issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary). The driver has the following
features:
- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some protocols (like one for some bitmap displays) require different clock
speed or word size settings for each transfer in an SPI message. This adds
those parameters to struct spi_transfer. They are to be used when they are
nonzero; otherwise the defaults from spi_device are to be used.
The patch also adds a setup_transfer callback to spi_bitbang, uses it for
messages that use those overrides, and implements it so that the pure
bitbanging code can help resolve any questions about how it should work.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.
Cc: netdev@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Andrew Victor
The serial_core already manages the power state of the UARTs, and
therefore it shouldn't suspend a UART which was previously suspended.
This patch modifies serial_core only call the UART-specific
power-management function if the PM state is actually changing.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
