Commit Graph

168225 Commits

Author SHA1 Message Date
Luotao Fu
d65aea99bd mpc52xx_spi: add missing mode_bits definition
V2 changes:
* remove CS_HIGH mode

Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-08 18:48:13 -07:00
Luotao Fu
4a495b1c43 mpc52xx_spi: fix clearing status register
Before reading status register to check MODF failure, we have to clear it
first since the MODF flag will be set after initializing the spi master,
if the hardware comes up with a low SS. The processor datasheet reads:
Mode Fault flag -- bit sets if SS input goes low while SPI is configured as a
master. Flag is cleared automatically by an SPI status register read (with MODF
set) followed by a SPI control register 1 write.
Hence simply rereading the register is not sufficient to clear the flag. We
redo the write also to make sure to clear the flag.

V2 Changes:
* change variable type from int to u8

Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-08 18:48:13 -07:00
Albrecht Dreß
6d5355998a mpc52xx/wdt: remove obsolete old WDT implementation
Remove the old WDT implementation.

Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-08 14:42:28 -07:00
Albrecht Dreß
eda43d16ef mpc52xx/wdt: merge WDT code into the GPT driver
Merge the WDT code into the GPT interface.

Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-13 11:09:31 -07:00
Albrecht Dreß
13b600b59d mpc52xx/wdt: OF property to enable the WDT on boot
Add the "fsl,wdt-on-boot" OF property as to reserve a GPT as WDT which may
be a requirement in safety-related (e.g. ISO/EN 61508) applications.

Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-13 11:09:30 -07:00
Albrecht Dreß
690b846aa1 mpc5200/gpt: tiny fix for gpt period limitation
This patch changes the period parameter of mpc52xx_gpt_start_timer to
a u64 to support larger timeout periods.

Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-12 13:31:35 -07:00
Grant Likely
02d9e58e46 mmc: fix missing module license declaration in of_mmc_spi.c
Driver cannot be used as a module without this patch.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-04 22:43:35 -07:00
Albrecht Dreß
a22c65f81a powerpc: tiny memcpy_(to|from)io optimisation
This trivial patch changes memcpy_(to|from)io as to transfer as many
32-bit words as possible in 32-bit accesses (in the current solution,
the last 32-bit word was transferred as 4 byte accesses).

Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-04 16:43:12 -07:00
Wolfram Sang
5cc17d7e01 spi/mpc52xx: replace printk with dev_err
To easily identify which device has problems.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-04 16:42:47 -07:00
John Linn
1a8d3b777d Xilinx: SPI: Fix bits_per_word for transfers
The bits_per_word value can be set for each transfer, or can
be set to zero in each transfer in which case it should default
to the value in the driver.

The driver was fixed to properly check the bits_per_word in
the transfer that is passed in.

Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-04 16:42:47 -07:00
Wolfram Sang
f856cf0178 spi/mpc52xx-psc-spi: check for valid PSC
This driver calls mpc52xx_set_psc_clkdiv() but doesn't check its return value
to see if the PSC is actually valid for SPI use. Add the check and a hint for
the user.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-04 16:42:47 -07:00
John Bonesio
3c9059d79f powerpc/5200: add LocalPlus bus FIFO device driver
This is a driver for the FIFO device on the LocalPlus bus on an mpc5200 system.
The driver supports programmed I/O through the FIFO as well as setting up DMA
via the BestComm engine through the FIFO.

Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-04 16:42:47 -07:00
Grant Likely
4f59ecfa9b powerpc/5200: add general purpose timer API for the MPC5200
This patch adds an interface for controlling the timer function of the
MPC5200 GPT devices.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-04 16:42:33 -07:00
Grant Likely
42bbb70980 powerpc/5200: Add mpc5200-spi (non-PSC) device driver
Adds support for the dedicated SPI device on the Freescale MPC5200(b)
SoC.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-11-04 15:34:18 -07:00
Grant Likely
ad6577629a spi/mpc5200: Register SPI devices described in device tree
Add call to of_register_spi_devices() to register SPI devices described
in the OF device tree.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
2009-11-04 15:23:37 -07:00
Linus Torvalds
b419148e56 Linux 2.6.32-rc6 2009-11-03 11:37:49 -08:00
Linus Torvalds
79051db9ae Merge branch 'for-linus' of git://github.com/at91linux/linux-2.6-at91
* 'for-linus' of git://github.com/at91linux/linux-2.6-at91:
  at91: at91sam9g45 family: identify several chip versions
  avr32: add two new at91 to cpu.h definition
2009-11-03 11:15:25 -08:00
Nicolas Ferre
d8951adeba at91: at91sam9g45 family: identify several chip versions
cpu_is_xxx() macros are identifying generic at91sam9g45 chip. This patch adds
the capacity to differentiate Engineering Samples and final lots through the
inclusion of  at91_cpu_fully_identify() and the related chip IDs with chip
version field preserved.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2009-11-03 18:42:31 +01:00
Nicolas Ferre
2f5d46d2f6 avr32: add two new at91 to cpu.h definition
Somme common drivers will need those at91 cpu_is_xxx() definitions. As
at91sam9g10 and at91sam9g45 are on the way to linus' tree, here is the patch
that adds those chips to cpu.h in AVR32 architecture.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-11-03 18:36:35 +01:00
Linus Torvalds
9ddfd92909 Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (38 commits)
  MIPS: O32: Fix ppoll
  MIPS: Oprofile: Rename cpu_type from godson2 to loongson2
  MIPS: Alchemy: Fix hang with high-frequency edge interrupts
  MIPS: TXx9: Fix spi-baseclk value
  MIPS: bcm63xx: Set the correct BCM3302 CPU name
  MIPS: Loongson 2: Set cpu_has_dc_aliases and cpu_icache_snoops_remote_store
  MIPS: Avoid potential hazard on Context register
  MIPS: Octeon: Use lockless interrupt controller operations when possible.
  MIPS: Octeon: Use write_{un,}lock_irq{restore,save} to set irq affinity
  MIPS: Set S-cache linesize to 64-bytes for MTI's S-cache
  MIPS: SMTC: Avoid queing multiple reschedule IPIs
  MIPS: GCMP: Avoid accessing registers when they are not present
  MIPS: GIC: Random fixes and enhancements.
  MIPS: CMP: Fix memory barriers for correct operation of amon_cpu_start
  MIPS: Fix abs.[sd] and neg.[sd] emulation for NaN operands
  MIPS: SPRAM: Clean up support code a little
  MIPS: 1004K: Enable SPRAM support.
  MIPS: Malta: Enable PCI 2.1 compatibility in PIIX4
  MIPS: Kconfig: Fix duplicate default value for MIPS_L1_CACHE_SHIFT.
  MIPS: MTI: Fix accesses to device registers on MIPS boards
  ...
2009-11-03 08:09:57 -08:00
Linus Torvalds
38dc63459f Merge branch 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: Remove some debug messages producing too much noise
  PM: Fix warning on suspend errors
  PM / Hibernate: Add newline to load_image() fail path
  PM / Hibernate: Fix error handling in save_image()
  PM / Hibernate: Fix blkdev refleaks
  PM / yenta: Split resume into early and late parts (rev. 4)
2009-11-03 07:52:57 -08:00
Ian Campbell
1d51075094 Correct nr_processes() when CPUs have been unplugged
nr_processes() returns the sum of the per cpu counter process_counts for
all online CPUs. This counter is incremented for the current CPU on
fork() and decremented for the current CPU on exit(). Since a process
does not necessarily fork and exit on the same CPU the process_count for
an individual CPU can be either positive or negative and effectively has
no meaning in isolation.

Therefore calculating the sum of process_counts over only the online
CPUs omits the processes which were started or stopped on any CPU which
has since been unplugged. Only the sum of process_counts across all
possible CPUs has meaning.

The only caller of nr_processes() is proc_root_getattr() which
calculates the number of links to /proc as
        stat->nlink = proc_root.nlink + nr_processes();

You don't have to be all that unlucky for the nr_processes() to return a
negative value leading to a negative number of links (or rather, an
apparently enormous number of links). If this happens then you can get
failures where things like "ls /proc" start to fail because they got an
-EOVERFLOW from some stat() call.

Example with some debugging inserted to show what goes on:
        # ps haux|wc -l
        nr_processes: CPU0:     90
        nr_processes: CPU1:     1030
        nr_processes: CPU2:     -900
        nr_processes: CPU3:     -136
        nr_processes: TOTAL:    84
        proc_root_getattr. nlink 12 + nr_processes() 84 = 96
        84
        # echo 0 >/sys/devices/system/cpu/cpu1/online
        # ps haux|wc -l
        nr_processes: CPU0:     85
        nr_processes: CPU2:     -901
        nr_processes: CPU3:     -137
        nr_processes: TOTAL:    -953
        proc_root_getattr. nlink 12 + nr_processes() -953 = -941
        75
        # stat /proc/
        nr_processes: CPU0:     84
        nr_processes: CPU2:     -901
        nr_processes: CPU3:     -137
        nr_processes: TOTAL:    -954
        proc_root_getattr. nlink 12 + nr_processes() -954 = -942
          File: `/proc/'
          Size: 0               Blocks: 0          IO Block: 1024   directory
        Device: 3h/3d   Inode: 1           Links: 4294966354
        Access: (0555/dr-xr-xr-x)  Uid: (    0/    root)   Gid: (    0/    root)
        Access: 2009-11-03 09:06:55.000000000 +0000
        Modify: 2009-11-03 09:06:55.000000000 +0000
        Change: 2009-11-03 09:06:55.000000000 +0000

I'm not 100% convinced that the per_cpu regions remain valid for offline
CPUs, although my testing suggests that they do. If not then I think the
correct solution would be to aggregate the process_count for a given CPU
into a global base value in cpu_down().

This bug appears to pre-date the transition to git and it looks like it
may even have been present in linux-2.6.0-test7-bk3 since it looks like
the code Rusty patched in http://lwn.net/Articles/64773/ was already
wrong.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-11-03 07:52:39 -08:00
Linus Torvalds
1c211849d8 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: gpio-keys - use IRQF_SHARED
  Input: winbond-cir - select LEDS_TRIGGERS
  Input: i8042 - try to get stable CTR value when initializing
  Input: atkbd - add a quirk for OQO 01+ multimedia keys
2009-11-03 07:46:17 -08:00
Linus Torvalds
fcef24d38e Merge branch 'fixes-s3c-2632-rc5' of git://git.fluff.org/bjdooks/linux
* 'fixes-s3c-2632-rc5' of git://git.fluff.org/bjdooks/linux:
  ARM: S3C2410: Fix sparse warnings in arch/arm/mach-s3c2410/gpio.c
  ARM: S3C2440: mini2440: Fix spare warnings
  ARM: S3C24XX: Fix warnings in arch/arm/plat-s3c24xx/gpio.c
  ARM: S3C2440: mini2440: Fix missing CONFIG_S3C_DEV_USB_HOST
  ARM: S3C24XX: arch/arm/plat-s3c24xx: Move dereference after NULL test
  ARM: S3C: Fix adc function exports
  ARM: S3C2410: Fix link if CONFIG_S3C2410_IOTIMING is not set
  ARM: S3C24XX: Introduce S3C2442B CPU
  ARM: S3C24XX: Define a macro to avoid compilation error
  ARM: S3C: Add info for supporting circular DMA buffers
  ARM: S3C64XX: Set rate of crystal mux
  ARM: S3C64XX: Fix S3C64XX_CLKDIV0_ARM_MASK value
2009-11-03 07:46:05 -08:00
Linus Torvalds
78e1e34056 Merge branch 'i2c-fixes' of git://git.fluff.org/bjdooks/linux
* 'i2c-fixes' of git://git.fluff.org/bjdooks/linux:
  i2c-mpc: Do not generate STOP after read.
  i2c: imx: disable clock when it's possible to save power.
  i2c: imx: only imx1 needs disable delay
  i2c: imx: check busy bit when START/STOP
2009-11-03 07:45:50 -08:00
Linus Torvalds
1cec2cdee4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: add zero-fill for new btree node buffers
  nilfs2: fix irregular checkpoint creation due to data flush
  nilfs2: fix dirty page accounting leak causing hang at write
2009-11-03 07:45:22 -08:00
Linus Torvalds
a84216e671 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
  mac80211: check interface is down before type change
  cfg80211: fix NULL ptr deref
  libertas if_usb: Fix crash on 64-bit machines
  mac80211: fix reason code output endianness
  mac80211: fix addba timer
  ath9k: fix misplaced semicolon on rate control
  b43: Fix DMA TX bounce buffer copying
  mac80211: fix BSS leak
  rt73usb.c : more ids
  ipw2200: fix oops on missing firmware
  gre: Fix dev_addr clobbering for gretap
  sky2: set carrier off in probe
  net: fix sk_forward_alloc corruption
  pcnet_cs: add cis of PreMax PE-200 ethernet pcmcia card
  r8169: Fix card drop incoming VLAN tagged MTU byte large jumbo frames
  ibmtr: possible Read buffer overflow?
  net: Fix RPF to work with policy routing
  net: fix kmemcheck annotations
  e1000e: rework disable K1 at 1000Mbps for 82577/82578
  e1000e: config PHY via software after resets
  ...
2009-11-03 07:44:01 -08:00
Pavel Machek
2ddac2a6a8 PM: Remove some debug messages producing too much noise
pm_runtime_idle() is somewhat noisy. Remove debug prints.

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2009-11-03 11:18:18 +01:00
Romit Dasgupta
e528e87689 PM: Fix warning on suspend errors
Fixes the point where we need to complete the power transition when
device suspend fails, so that we don't print warnings about devices
added to the device hierarchy after a failing suspend.

[rjw: Modified changelog.]

Signed-off-by: Romit Dasgupta <romit@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2009-11-03 11:03:33 +01:00
Jiri Slaby
bf9fd67a03 PM / Hibernate: Add newline to load_image() fail path
Finish a line by \n when load_image fails in the middle of loading.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2009-11-03 11:03:09 +01:00
Jiri Slaby
4ff277f9e4 PM / Hibernate: Fix error handling in save_image()
There are too many retval variables in save_image(). Thus error return
value from snapshot_read_next() may be ignored and only part of the
snapshot (successfully) written.

Remove 'error' variable, invert the condition in the do-while loop
and convert the loop to use only 'ret' variable.

Switch the rest of the function to consider only 'ret'.

Also make sure we end printed line by \n if an error occurs.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2009-11-03 11:02:43 +01:00
Jiri Slaby
76b57e613f PM / Hibernate: Fix blkdev refleaks
While cruising through the swsusp code I found few blkdev reference
leaks of resume_bdev.

swsusp_read: remove blkdev_put altogether. Some fail paths do
             not do that.
swsusp_check: make sure we always put a reference on fail paths
software_resume: all fail paths between swsusp_check and swsusp_read
                 omit swsusp_close. Add it in those cases. And since
                 swsusp_read doesn't drop the reference anymore, do
                 it here unconditionally.

[rjw: Fixed a small coding style issue.]

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2009-11-03 11:01:46 +01:00
Rafael J. Wysocki
9905d1b411 PM / yenta: Split resume into early and late parts (rev. 4)
Commit 0c570cdeb8
(PM / yenta: Fix cardbus suspend/resume regression) caused resume to
fail on systems with two CardBus bridges.  While the exact nature
of the failure is not known at the moment, it can be worked around by
splitting the yenta resume into an early part, executed during the
early phase of resume, that will only resume the socket and power it
up if there was a card in it during suspend, and a late part,
executed during "regular" resume, that will carry out all of the
remaining yenta resume operations.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14334, which is a
listed regression from 2.6.31.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reported-by: Stephen J. Gowdy <gowdy@cern.ch>
Tested-by: Jose Marino <braket@hotmail.com>
2009-11-03 10:54:58 +01:00
Dmitry Eremin-Solenikov
558a5e296a Input: gpio-keys - use IRQF_SHARED
There is nothing that disallows gpio-keys to share it's IRQ line
w/ other drivers. Make it use IRQF_SHARED in request_irq().

An example of other driver with which I'd like to share IRQ line
for GPIO buttons is ledtrig-gpio.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-02 22:12:37 -08:00
David Härdeman
0baa3de6eb Input: winbond-cir - select LEDS_TRIGGERS
drivers/input/misc/winbond-cir.c depends on LEDS_TRIGGERS so
add an appropriate select to drivers/input/misc/Kconfig

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-02 22:12:29 -08:00
Dmitry Torokhov
ee1e82cee5 Input: i8042 - try to get stable CTR value when initializing
If user presses keys while i8042 is being initialized there is a chance
that keyboard data will be mistaken for results of Read Control Register
command causing futher troubles. Work around this issue by reading CTR
several times and stop when we get matching results.

Reported-and-tested-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-02 22:11:43 -08:00
Dmitry Torokhov
7a53c7f56b Merge commit 'v2.6.32-rc5' into for-linus 2009-11-02 22:10:07 -08:00
Ryusuke Konishi
05b4358ad5 nilfs2: add zero-fill for new btree node buffers
Adds missing initialization of newly allocated b-tree node buffers.
This avoids garbage data to be mixed in b-tree node blocks.

Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
2009-11-03 12:32:03 +09:00
Ryusuke Konishi
aeda7f6343 nilfs2: fix irregular checkpoint creation due to data flush
When nilfs flushes out dirty data to reduce memory pressure, creation
of checkpoints is wrongly postponed.  This bug causes irregular
checkpoint creation especially in small footprint systems.

To correct this issue, a timer for the checkpoint creation has to be
continued if a log writer does not create a checkpoint.

This will do the correction.

Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
2009-11-03 12:32:03 +09:00
Ryusuke Konishi
b1e19e5601 nilfs2: fix dirty page accounting leak causing hang at write
Bruno Prémont and Dunphy, Bill noticed me that NILFS will certainly
hang on ARM-based targets.

I found this was caused by an underflow of dirty pages counter.  A
b-tree cache routine was marking page dirty without adjusting page
account information.

This fixes the dirty page accounting leak and resolves the hang on
arm-based targets.

Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Reported-by: Dunphy, Bill <WDunphy@tandbergdata.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: stable <stable@kernel.org>
2009-11-03 12:31:36 +09:00
David S. Miller
bcfe3c2046 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2009-11-02 19:18:50 -08:00
Joakim Tjernlund
45da790ebe i2c-mpc: Do not generate STOP after read.
The driver always ends a read with a STOP condition which
breaks subsequent I2C reads/writes in the same transaction as
these expect to do a repeated START(ReSTART).

This will also help I2C multimaster as the bus will not be released
after the first read, but when the whole transaction ends.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-11-02 23:28:47 +00:00
Richard Zhao
db3a3d4ef7 i2c: imx: disable clock when it's possible to save power.
Enable clock before START, disable it after STOP.

Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-11-02 23:28:47 +00:00
Richard Zhao
a4094a76e6 i2c: imx: only imx1 needs disable delay
check cpu_is_mx1() when disable delay.

Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-11-02 23:28:47 +00:00
Richard Zhao
43309f3b52 i2c: imx: check busy bit when START/STOP
The controller can't do anything else before it actually generates START/STOP.
So we check busy bit to make sure START/STOP is successfully finished.

If we don't check busy bit, START/STOP may fail on some fast CPUs.

Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-11-02 23:28:46 +00:00
Linus Torvalds
1836d95928 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: fix readdir corner cases
  9p: fix readlink
  9p: fix a small bug in readdir for long directories
2009-11-02 12:23:21 -08:00
Johannes Berg
c1f9a764cf mac80211: check interface is down before type change
For some strange reason the netif_running() check
ended up after the actual type change instead of
before, potentially causing all kinds of problems
if the interface is up while changing the type;
one of the problems manifests itself as a warning:

WARNING: at net/mac80211/iface.c:651 ieee80211_teardown_sdata+0xda/0x1a0 [mac80211]()
Hardware name: Aspire one
Pid: 2596, comm: wpa_supplicant Tainted: G        W  2.6.31-10-generic #32-Ubuntu
Call Trace:
 [] warn_slowpath_common+0x6d/0xa0
 [] warn_slowpath_null+0x15/0x20
 [] ieee80211_teardown_sdata+0xda/0x1a0 [mac80211]
 [] ieee80211_if_change_type+0x4a/0xc0 [mac80211]
 [] ieee80211_change_iface+0x61/0xa0 [mac80211]
 [] cfg80211_wext_siwmode+0xc7/0x120 [cfg80211]
 [] ioctl_standard_call+0x58/0xf0

(http://www.kerneloops.org/searchweek.php?search=ieee80211_teardown_sdata)

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-02 15:14:07 -05:00
Johannes Berg
7400f42e9d cfg80211: fix NULL ptr deref
commit 211a4d12abf86fe0df4cd68fc6327cbb58f56f81
  Author: Johannes Berg <johannes@sipsolutions.net>
  Date:   Tue Oct 20 15:08:53 2009 +0900

      cfg80211: sme: deauthenticate on assoc failure

introduced a potential NULL pointer dereference that
some people have been hitting for some reason -- the
params.bssid pointer is not guaranteed to be non-NULL
for what seems to be a race between various ways of
reaching the same thing.

While I'm trying to analyse the problem more let's
first fix the crash. I think the real fix may be to
avoid doing _anything_ if it ended up being NULL, but
right now I'm not sure yet.

I think
http://bugzilla.kernel.org/show_bug.cgi?id=14342
might also be this issue.

Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Tested-by: Parag Warudkar <parag.lkml@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-02 15:14:07 -05:00
Linus Torvalds
333a07437c Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  Revert "[IA64] fix percpu warnings"
  [IA64] fix percpu warnings
  [IA64] SMT friendly version of spin_unlock_wait()
  [IA64] use printk_once() unaligned.c/io_common.c
  [IA64] Require SAL 3.2 in order to do extended config space ops
  [IA64] unsigned cannot be less than 0 in sn_hwperf_ioctl()
  [IA64] Restore registers in the stack on INIT
  [IA64] Re-implement spinaphores using ticket lock concepts
  [IA64] Squeeze ticket locks back into 4 bytes.
2009-11-02 10:22:25 -08:00
Linus Torvalds
d4da6c9ccf Revert "ext4: Remove journal_checksum mount option and enable it by default"
This reverts commit d0646f7b63, as
requested by Eric Sandeen.

It can basically cause an ext4 filesystem to miss recovery (and thus get
mounted with errors) if the journal checksum does not match.

Quoth Eric:

   "My hand-wavy hunch about what is happening is that we're finding a
    bad checksum on the last partially-written transaction, which is
    not surprising, but if we have a wrapped log and we're doing the
    initial scan for head/tail, and we abort scanning on that bad
    checksum, then we are essentially running an unrecovered filesystem.

    But that's hand-wavy and I need to go look at the code.

    We lived without journal checksums on by default until now, and at
    this point they're doing more harm than good, so we should revert
    the default-changing commit until we can fix it and do some good
    power-fail testing with the fixes in place."

See

	http://bugzilla.kernel.org/show_bug.cgi?id=14354

for all the gory details.

Requested-by: Eric Sandeen <sandeen@redhat.com>
Cc: Theodore Tso <tytso@mit.edu>
Cc: Alexey Fisher <bug-track@fisher-privat.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mathias Burén <mathias.buren@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-11-02 10:15:27 -08:00