This patch adds the Testo USB interface to the list of devices
recognized by the ftdi_sio module. This device is based on a FT232BL
chip, and is used as an interface to get data from digital sensors
(thermometer, etc). See http://www.testo.com/
Signed-off-by: Colin Leroy <colin@colino.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as749) extends the unusual_devs entry for the Sony DSC-T1 and
T5 to cover the H5 as well.
From: Lars Jacob <jacob.lars@googlemail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as748) adds an unusual_devs entry for the Nokia E61 mobile
phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as745) adds an unusual_devs entry for the Nokia N91, just like
the entry for the N80 added a couple of weeks ago. Apparently Nokia isn't
using very good firmware these days...
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I just got a "ZyXEL Prestige USB Adapter" that is actually RTL8150
adapter. Here is the relevant /proc/bus/usb/devices output (after
adding the vendor/product IDs to the driver):
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#=119 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0586 ProdID=401a Rev= 1.00
S: Manufacturer=ZyXEL
S: Product=Prestige USB Adapter
S: SerialNumber=1027
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=120mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=rtl8150
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
This patch adds the ZyXEL vendor ID to the rtl8150.c driver. The
device has absolutely no identifying marks on the outside for model
type, just a serial number, and I can't find anything on ZyXEL's
website, so I called the product ID PRODUCT_ID_PRESTIGE to match the
product string.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Acked-by: <petkan@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is to get the WiseGroup.,Ltd SmartJoy Dual Plus PS2-to-USB
Adapter [0x6677:0x8802] correctly detected. It sets the NOGET and
MULTI_INPUT quirks to make 2 joystick nodes appear in stead of only
one.
(As of yet, only confirmed working by myself.)
Signed-off-by: Navaho Gunleg <navahogunleg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The below patch fixes the ipw module in kernel 2.6.17 for me; without
this change it simply does not work at all (all but the first writes are
refused because write_urb_busy is always 1).
This problem was there in 2.6.15 as well, but at that point I used the
(updated) ipw.c, version 0.4, from
http://www.neology.co.za/products/opensource/ipwireless/ which no longer
compiles with 2.6.17. It can be made to after a few changes but
obviously it's easier if the built-in ipw driver works instead of having
to download one from the neology site.
From: Bart Oldeman <bartoldeman@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Devfs is gone. We can remove that information.
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove destructor and call kmem_cache_create with NULL for the destructor.
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds configurable waiting periods to the ipaq connection code. These are
not needed when the pocketpc device is running normally when plugged in,
but they need extra delays if they are physically connected while
rebooting.
There are two parameters :
* initial_wait : this is the delay before the driver attemts to start the
connection. This is needed because the pocktpc device takes much
longer to boot if the driver starts sending control packets too soon.
* connect_retries : this is the number of times the control urb is
retried before finally giving up. The patch also adds a 1 second delay
between retries.
I'm not sure if the cases where this patch is useful are general enough
to include this in the kernel.
Signed-off-by: Frank Gevaerts <frank.gevaerts@fks.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes several problems in the ipaq.c driver with connecting
and disconnecting pocketpc devices:
* The read urb stayed active if the connect failed, causing nullpointer
dereferences later on.
* If a write failed, the driver continued as if nothing happened. Now it
handles that case the same way as other usb serial devices (fix by
Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>)
Signed-off-by: Frank Gevaerts <frank.gevaerts@fks.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In a rare and all-but-unused path, the EHCI driver could reuse a variable
in a way that'd make trouble. Specifically, if the first root hub port
gets an overcurrent event (rare) during a remote wakeup scenario (all but
unused in today's Linux, except for folk working with suspend-to-RAM and
similar sleep states), that would look like a fatal error which would shut
down the controller. Fix by not reusing that variable.
Spotted by Per Hallsmark <saxofon@musiker.nu>
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6661
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch creates a new driver, sierra.c, that supports the new
non-composite Sierra Wireless WWAN devices. The older Sierra
Wireless and Airprime devices are supported in airprime.c.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
coverity spotted (id #185) that we still use urb, if the allocation
fails in the error path. This patch fixes this by returning directly.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move variables only used on !__hppa__ into that #ifndef section. This
cleans up a compiler warning on parisc. Problem pointed out by
Joel Soete.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch limits the amount of outstanding 'write' data that can be
queued up for the ftdi_sio driver, to prevent userspace DoS attacks (or
simple accidents) that use up all the system memory by writing lots of
data to the serial port.
The original patch was by Guillaume Autran, who in turn based it on the
same mechanism implemented in the 'visor' driver. I (Ian Abbott)
re-targeted the patch to the latest sources, fixed a couple of errors,
renamed his new structure members, and updated the implementations of
the 'write_room' and 'chars_in_buffer' methods to take account of the
number of outstanding 'write' bytes. It seems to work fine, though at
low baud rates it is still possible to queue up an amount of data that
takes an age to shift (a job for another day!).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The anti user-DoS mechanism in the USB serial 'visor' driver can fail in
the following way:
visor_open: priv->outstanding_urbs = 0
visor_write: ++priv->outstanding_urbs
visor_close:
visor_open: priv->outstanding_urbs = 0
visor_write_bulk_callback: --priv->outstanding_urbs
So priv->outstanding_urbs ends up as (unsigned long)(-1). Not good!
I haven't seen this happen with the visor driver as I don't have the
hardware, but I have seen it while testing a patch to implement the same
functionality in the ftdi_sio driver (patch not yet submitted).
The fix is pretty simple: don't reinitialize outstanding_urbs in
visor_open. (Again, I haven't tested the fix in visor, but I have
tested it in ftdi_sio.)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the kernel version to the usb-storage Protocol/SubClass
unneeded message in order to help us troubleshoot such problems.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a US_FL_MAX_SECTORS_64 and removes the Genesys special-cases
for this that were in scsiglue.c. It also adds the flag to other devices
reported to need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as731) makes a couple of small fixes to the hub_port_resume
routine:
Don't return status >= 0 when an error occurs;
Clear the port-change-suspend status indicator after
resuming a device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as730) contains an unusual_devs entry for a Samsung MP3
device.
From: Ernis <ernisv@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as725) adds an unusual_devs entry for the Motorola RAZR V3x.
From: Davide Perini <perini.davide@dpsoftware.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
finish_device_resume() in the hub driver isn't careful always to return
a negative code in all the error pathways. It also doesn't return 0 in
all the success pathways. This patch (as724) fixes the behavior.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My recent patch converting usb-storage to use
usb_reset_composite_device() added a bug, a race between reset and
disconnect. It was necessary to drop the private lock while executing a
reset, and if a disconnect occurs at that time it will cause a crash.
This patch (as722) fixes the problem by explicitly checking for an early
termination after executing each command.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds
better debugging output &
an update of the quirk list
to the acm driver
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a new driver for the Cypress CY7C63xxx mirco controller series.
It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus
GmbH. It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I
ported to kernel 2.6 using sysfs. I intend to support more controllers
of this family (and more features) as soon as I get hold of the required
IDs etc. Please see the source code's header for more information.
Signed-off-by: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbfs stores the wrong signal number in the siginfo structure used for
notifying user programs about device disconnect. This patch (as726)
fixes it.
From: Zoran Marceta <Zoran.Marceta@micronasnit.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Susteen Datapilot cable
(http://www.susteen.com/productdetail/71/producthl/Notempty) has an
internal pl2303 to communicate with a set of dummy connector-ends that
connect to a variety of cell phones. I've found that it works right out
of the box by simply adding the product/vendor id to the pl2303 driver.
Signed-off-by: Matt Meno <mmeno@idealcorp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes blatant leaks in visor driver and makes it report
mode sensible things in ->write_room (this is only needed if your visor
is a terminal though).
It is made to fit into 80 columns with a temporary variable.
Might even save a few instructions...
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fix addresses two issues:
- Unattached port structures were not freed
- My initial fix for crash when eventd runs a work in a freed port
did not go far enough
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed this while debugging something unrelated on
sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Text from the back of the box, for your information/amusement:
USB DATA CABLE
FOR K700 Series
The USB Cable is an ideal link between your mobile phone and PC. Employing
the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions
such as synchronization of phone book and calendar,as well as Internet browsing via
a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity.
MADE IN CHINA
From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds OHCI glue bits for the USB host interface in the
Cirrus ep93xx (arm920t) CPU.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I received an DBAU1200 eval kit from AMD a few days ago and tried to
enable the USB2 port, but the current linux-2.6 GIT did not even
compile with CONFIG_SOC_1200, CONFIG_SOC_AU1X00, CONFIG_USB_EHCI and
CONFIG_USB_OHCI set.
Furthermore, in ehci-hcd.c, platform_driver_register() was called with
an improper argument of type 'struct device_driver *' which of course
ended up in a kernel oops. How could that ever have worked on your
machines?
Anyway, here's a trivial patch that makes the USB subsystem working
on my board for both OHCI and EHCI.
It also removes the /* FIXME use "struct platform_driver" */.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Compile fixes for au1200 ohci.
First part looks a bit hackish... but it works for me.
Signed-off-by: Domen Puncer <domen.puncer@ultra.si>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the abituguru driver is seeing some more widespread testing
it has turned out that one the first generation of Abit uGuru
motherboards, with uGuru revision 1, the autodetect bank1 sensor type
code doesn't (always) work. This patch adds a module param to override
the autodetect, and it adds validity checks for the value of the 2
other autodetection override module params. An example of howto use
the new param can be found here:
http://lm-sensors.org/wiki/Configurations/Abit/AN7
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pca9539 driver doesn't honor the force parameter; it always does
detection. This patch will skip detection if forced.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Content-Disposition: inline; filename=i2c-algo-error-handling-fix.patch
It is possible for i2c_add_adapter() to fail. Several I2C algorithm
drivers ignore that fact. This (compile-tested only) patch fixes them.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the value returned by the i2c-powermac's master_xfer method.
It should return the number of messages processed successfully, but
instead returns the number of data bytes in the first (and only)
processed message.
Also explicitly mention the master_xfer convention so that future
implementations get it right directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scx200_acb i2c bus driver pretends to support SMBus block
transactions, but in fact it implements the more simple I2C block
transactions. Additionally, it lacks sanity checks on the length
of the block transactions, which could lead to a buffer overrun.
This fixes an oops reported by Alexander Atanasov:
http://marc.theaimsgroup.com/?l=linux-kernel&m=114970382125094
Thanks to Ben Gardner for fixing my bugs :)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the scx200_acb state machine:
* Nack was sent one byte too late on reads >= 2 bytes.
* Stop bit was set one byte too late on reads.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid addressing self when sending a slave address. Follows instruction
in Intel 80331/80321 manuals.
Ignoring this worked previously on 80321, but causes a hang on i2cdetect
on 80331.
Signed-off-by: Peter Milne <peter.milne@d-tacq.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug in the handling of 'ignore' module parameters of I2C
client drivers.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the driver handles multiple packets per NAPI poll, it is
better to reload the receive ring, then tell the hardware. Otherwise,
under packet storm with flow control, the driver/hardware will degrade
down to one packet getting through per pause-exchange.
Likewise on transmit, don't wakeup until a little more than minimum
ring space is available.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The documentation says we need to wait after turning on the PHY.
Also, don't enable WOL by default.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The changes to handle suspend/resume didn't handle the case where
a dual port card has the first port down, but the second is running.
In this driver, all NAPI polling is done on the primary port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since sky2_reset gets call from sky2_resume it shouldn't be tagged
with devinit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in (same problem
as sky2 driver). Should be three bits wide, but the mask only allows
for 1 bit to be set.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in (same problem
as sky2 driver). Should be three bits wide, but the mask only allows
for 1 bit to be set.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in sky2 driver. Should be
three bits wide, but the mask only allows for 1 bit to be set.
Thanks & Regards
Neil
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
sky2.h | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/w1/w1_io.h is both a subset of drivers/w1/w1.h and no longer
#include'd by any file.
This patch therefore removes w1_io.h.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The idle check loop has a greater-than where it should have a less-than.
This causes the ds2482 driver to check for the idle condition exactly
once, which causes it to fail on faster machines.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Morton wrote:
> All these functions return error codes, and we're not checking them. We
> should. So there's a patch which marks all these things as __must_check,
> which causes around 1,500 new warnings.
>
The following patch fixes such a warning in myri10ge.
Check pci_enable_device() return value in myri10ge_resume().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There were some tso bugs that only showed up with heavy load and 16kB
pages that this patch fixes by making the driver's internal use count
of descriptors match the count that it was estimating it needed using
the DESC_NEEDED macro. This bug caused NETDEV_WATCHDOG resets aka
tx timeouts.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
subsystem_configurations array is only used by an __init function,
therefore it should be marked __initdata, not __devinitdata.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/8139cp.c: In function 'cp_init_one':
drivers/net/8139cp.c:1919: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
drivers/net/8139cp.c:1919: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Modification and bug fixes with respect to irq registration.
- Enable interrupts after request_irq
- Restored MSI data register value at driver unload time
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the new names.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch defines the watermark registers and fixes up the use of this
register.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the definition for the deferral registers and fixes up
the use of these registers.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts generic HDLC (and WAN drivers using it) from
hdlc_set_carrier() to netif_dormant*() interface.
WAN hardware drivers should now use netif_carrier_on|off() like
other network drivers.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.
The actual chip setup done by the quirk is the precise setup recommended
by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Joseph Fannin reported that hpet_rtc_interrupt() enables hardirqs
in irq context:
[ 25.628000] [<c014af4e>] trace_hardirqs_on+0xce/0x200
[ 25.628000] [<c036cf21>] _spin_unlock_irq+0x31/0x70
[ 25.628000] [<c0296584>] rtc_get_rtc_time+0x44/0x1a0
[ 25.628000] [<c01198bb>] hpet_rtc_interrupt+0x21b/0x280
[ 25.628000] [<c0161141>] handle_IRQ_event+0x31/0x70
[ 25.628000] [<c0162d37>] handle_edge_irq+0xe7/0x210
[ 25.628000] [<c0106192>] do_IRQ+0x92/0x120
[ 25.628000] [<c0104121>] common_interrupt+0x25/0x2c
the call of rtc_get_rtc_time() is highly suspect. At a minimum we
need the patch below to save/restore hardirq state.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Joseph Fannin <jfannin@gmail.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like someone confused kmem_cache_create with a different allocator
and was attempting to give it knowledge of how many cache entries there
were.
With the unfortunate result that each slab entry was big enough to hold
every irq.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apparently the D700 has had an argument ordering issue for quite a while
which can cause it to get the wrong scsi_id (I just got an unbootable
voyager system because of this). Hopefully this patch also fixes up all
the sectional mismatches within the driver.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Check all __must_check warnings in scsi_debug.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is confirmed to fix a hang due to PCI resource conflicts with
setting up the Cardbus bridge on old laptops with the 440MX chipsets.
Original report by Alessio Sangalli, lspci debugging help by Pekka
Enberg, and trial patch suggested by Daniel Ritz:
"From the docs available i would _guess_ this thing is really similar
to the 82443BX/82371AB combination. at least the SMBus base address
register is hidden at the very same place (32bit at 0x90 in function
3 of the "south" brigde)"
The dang thing is largely undocumented, but the patch was corroborated
by Asit Mallick:
"I am trying to find the register information. 440MX is an integration of
440BX north-bridge without AGP and PIIX4E (82371EB). PIIX4 quirk
should cover the ACPI and SMBus related I/O registers."
and verified to fix the problem by Alessio.
Cc: Daniel Ritz <daniel.ritz-ml@swissonline.ch>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Tested-by: Alessio Sangalli <alesan@manoweb.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Multipath devices for which SetPGID is not supported are not handled well.
Use NOP ccws for path verification (sans path grouping) when SetPGID is not
supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
first one) and try to find a common one. Moan if no common PGID can be
found (and use NOP verification). If no PGIDs have been set, use the css
global PGID (as before). (Rationale: SetPGID will get a command reject if
the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
will remove the old PGIDs. rcp will generate solicited CRWs which can be
savely ignored by the machine check handler (all other actions create
unsolicited CRWs).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The module parameters for xpram are not or in a wrong way parsed.
The xpram module uses the module_param_array directive with an int
parameter which causes the kernel to automatically parse the passed
numbers. This will cause errors if arguments are omitted or cause
wrong results if arguments have size qualifiers.
Use module_param_array with charp and parse the arguments later.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a reg_mutex to prevent unregistering a subchannel before it has been
registered. Since 2.6.17, we've seen oopses in kslowcrw when a device is
found to be not operational during sense id when doing initial device
recognition; it is not clear yet why that particular problem was not (yet)
observed with earlier kernels...
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Using the port_id for the channel is completely unnecessary since the
host_id/target_id are constructed to be globally unique. Also move
the mptsas driver on to virtual channel 1 for its raid devices.
Acked-by: "Moore, Eric" <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds the ability to add a backlink to a particular port. The
idea is to represent properly ports on expanders that are used
specifically for linking to the parent device in the topology.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Pavel Machek
From: Dirk Opfer <Dirk@Opfer-Online.de>
Fix ucb initialization on collie. Wrong frequency was used and that
led to things not working quite correctly. (I had to actually disable
checks in my tree to get it to boot). It now includes all the
neccessary parts to get it to compile :-).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: ACPI_DOCK: Initialize the atomic notifier list
ACPI: acpi_os_allocate() fixes
ACPI: SBS: fix initialization, sem2mutex
ACPI: add 'const' to several ACPI file_operations
ACPI: delete some defaults from ACPI Kconfig
ACPI: "Device `[%s]' is not power manageable" make message debug only
ACPI: ACPI_DOCK Kconfig
Revert "Revert "ACPI: dock driver""
ACPI: acpi_os_get_thread_id() returns current
ACPI: ACPICA 20060707
* HEAD:
[DCCP]: Fix sparse warnings.
[TCP]: Remove TCP Compound
[BPQ] lockdep: fix false positive
[IPV4] inetpeer: Get rid of volatile from peer_total
[AX.25]: Get rid of the last volatile.
No need for video to be always in
No need for smart battery driver to be always in
Acked-by: Len Brown <len.brown@intel.com>
Cc: linux-acpi@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bpqether is encapsulating AX.25 frames into ethernet frames. There is a
virtual bpqether device paired with each ethernet devices, so it's normal
to pass through dev_queue_xmit twice for each frame which triggers the
locking detector.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a proper prototype for i2o_parm_issue() in core.h.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the snsc driver uses force_sig to send init a SIGPWR when the
system overheats. This patch switches it to kill_proc instead which has
the following advantages:
(1) gets rid of one of the last remaining tasklist_lock users
in modular code
(2) simplifies the snsc code significantly
The downside is that an init implementation could in theory block SIGPWR
and it would not get delivered. The sysvinit code used by all major
distributions doesn't do this and blocking this signal in init would be a
rather stupid thing to do.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Switch from register_chrdev() to (register|alloc)_chrdev_region().
- use a cdev. This was intended for original patchset, but was
overlooked.
We use a single cdev for all pins (minor device-numbers), as gleaned
from cs5535_gpio, and in contrast to whats currently done in scx200_gpio
(which I'll fix soon)
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix module-init-func by repairing usage of platform_device_del/put in
module-exit-func. IOW, it imitates Ingo's 'mishaps' patch, which fixed the
module-init-func's undo handling.
Also fixes lack of release_region to undo the earlier registration.
Also starts to 'use a cdev' which was originally intended (its present in
scx200_gpio). Code compiles and runs, exhibits a lesser error than
previously. (re-register-chrdev fails)
Since I had to add "include <linux/cdev.h>", I went ahead and made 2
tweaks that fell into diff-context-window:
- remove include <linux/config.h> everyone's doing it
- copyright updates - current date is 'wrong'
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add LED Class device support for the Soekris net48xx Error LED. Tested
only on a net4801, but should work on a net4826 as well. I'd love to find
a way of detecting a Soekris net48xx device but there is no DMI or any
Soekris-specific PCI devices.
[akpm@osdl.org: fixlets, cleanups]
Signed-off-by: Chris Boot <bootc@bootc.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle memory-mapped chips properly, needed for example on DECstations.
This support was in Linux 2.4 but for some reason got lost in 2.6. This
patch is taken directly from the linux-mips repository.
[akpm@osdl.org: cleanup]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: Paul Gortmaker <penguin@muskoka.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Newer ARMs have a 40 bit physical address space, but mapping physical
memory above 4G needs a special page table format which we (currently?) do
not use for userspace mappings, so what happens instead is that mapping an
address >= 4G will happily discard the upper bits and wrap.
There is a valid_mmap_phys_addr_range() arch hook where we could check for
>= 4G addresses and deny the mapping, but this hook takes an unsigned long
address:
static inline int valid_mmap_phys_addr_range(unsigned long addr, size_t size);
And drivers/char/mem.c:mmap_mem() calls it like this:
static int mmap_mem(struct file * file, struct vm_area_struct * vma)
{
size_t size = vma->vm_end - vma->vm_start;
if (!valid_mmap_phys_addr_range(vma->vm_pgoff << PAGE_SHIFT, size))
So that's not much help either.
This patch makes the hook take a pfn instead of a phys address.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When EDAC was first introduced into the kernel it had a sysfs interface,
but due to some problems it was disabled in 2.6.16 and remained disabled in
2.6.17.
With feedback, several of the control and attribute files of that interface
had some good constructive feedback. PCI Blacklist/Whitelist was a major
set which has design issues and it has been removed in this patch. Instead
of storing PCI broken parity status in EDAC, it has been moved to the
pci_dev structure itself by a previous PCI patch. A future patch will
enable that feature in EDAC by utilizing the pci_dev info.
The sysfs is now enabled in this patch, with a minimal set of control and
attribute files for examining EDAC state and for enabling/disabling the
memory and PCI operations.
The Documentation for EDAC has also been updated to reflect the new state
of EDAC operation.
Signed-off-by:Doug Thompson <norsk5@xmisson.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whoops, better hope this never gets passed a null dev in its current state.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andreas Herrmann <aherrman@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two variables in drivers/s390/net/qeth_main.c:qeth_send_packet() are only
used if CONFIG_QETH_PERF_STATS. Move their definition under the same ifdef
to remove compiler warning.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the roundup() macro from binfmt_elf.c into linux/kernel.h as it's
generally useful.
[akpm@osdl.org: nuke all the other implementations]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We all failed to notice that Franck's recent update to usb-storage allowed
an URB to complete after its context data was no longer valid. This patch
(as746) makes the driver wait for the URB to complete whenever there's a
timeout.
Although timeouts in usb-storage are relatively uncommon, they do occur.
Without this patch the code in 2.6.18-rc1 will fault within an interrupt
handler, which is not nice at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pci channel state is currently uninitialized, thus there are two ways
of indicating that "everything's OK": 0 and 1. This is a bit of a burden.
If a devce driver wants to check if the pci channel is in a working or a
disconnected state, the driver writer must perform checks similar to
if((pdev->error_state != 0) &&
(pdev->error_state != pci_channel_io_normal)) {
whatever();
}
which is rather akward. The first check is needed because stuct pci_dev is
inited to all-zeros. The scond is needed because the error recovery will
set the state to pci_channel_io_normal (which is not zero).
This patch fixes this awkwardness.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes several problems:
- pmac_backlight_key() is called under interrupt context, and therefore
can't use mutexes or semaphores, so defer the backlight level for
later, as it's not critical (original code by Aristeu S. Rozanski F.
<aris@valeta.org>).
- Add exports for functions that might be called from modules
- Fix Kconfig depdencies on PMAC_BACKLIGHT.
- Fix locking issues on calls from inside the driver (reported by
Aristeu S. Rozanski F., too)
- Fix wrong calculation of backlight values in some of the drivers
- Replace pmac_backlight_key_up/down by inline functions
[akpm@osdl.org: fix function prototypes]
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Aristeu S. Rozanski F. <aris@valeta.org>
Acked-by: Rene Nussbaumer <linux-kernel@killerfox.forkbomb.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SMU driver tries to map an interrupt from the device-tree before the
interrupt controllers in the machine have been enumerated. This doesn't work
properly and cause machines like the Quad g5 to fail booting later on when
some drivers waits endlessly for an SMU request to complete. This is the
second problem preventing boot on the Quad g5. This fixes it and also makes
the SMU driver a bit more resilient to not having an interrupt.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch slightly reworks the new irq code to fix a small design error. I
removed the passing of the trigger to the map() calls entirely, it was not a
good idea to have one call do two different things. It also fixes a couple of
corner cases.
Mapping a linux virtual irq to a physical irq now does only that. Setting the
trigger is a different action which has a different call.
The main changes are:
- I no longer call host->ops->map() for an already mapped irq, I just return
the virtual number that was already mapped. It was called before to give an
opportunity to change the trigger, but that was causing issues as that could
happen while the interrupt was in use by a device, and because of the
trigger change, map would potentially muck around with things in a racy way.
That was causing much burden on a given's controller implementation of
map() to get it right. This is much simpler now. map() is only called on
the initial mapping of an irq, meaning that you know that this irq is _not_
being used. You can initialize the hardware if you want (though you don't
have to).
- Controllers that can handle different type of triggers (level/edge/etc...)
now implement the standard irq_chip->set_type() call as defined by the
generic code. That means that you can use the standard set_irq_type() to
configure an irq line manually if you wish or (though I don't like that
interface), pass explicit trigger flags to request_irq() as defined by the
generic kernel interfaces. Also, using those interfaces guarantees that
your controller set_type callback is called with the descriptor lock held,
thus providing locking against activity on the same interrupt (including
mask/unmask/etc...) automatically. A result is that, for example, MPIC's
own map() implementation calls irq_set_type(NONE) to configure the hardware
to the default triggers.
- To allow the above, the irq_map array entry for the new mapped interrupt
is now set before map() callback is called for the controller.
- The irq_create_of_mapping() (also used by irq_of_parse_and_map()) function
for mapping interrupts from the device-tree now also call the separate
set_irq_type(), and only does so if there is a change in the trigger type.
- While I was at it, I changed pci_read_irq_line() (which is the helper I
would expect most archs to use in their pcibios_fixup() to get the PCI
interrupt routing from the device tree) to also handle a fallback when the
DT mapping fails consisting of reading the PCI_INTERRUPT_PIN to know wether
the device has an interrupt at all, and the the PCI_INTERRUPT_LINE to get an
interrupt number from the device. That number is then mapped using the
default controller, and the trigger is set to level low. That default
behaviour works for several platforms that don't have a proper interrupt
tree like Pegasos. If it doesn't work for your platform, then either
provide a proper interrupt tree from the firmware so that fallback isn't
needed, or don't call pci_read_irq_line()
- Add back a bit that got dropped by my main rework patch for properly
clearing pending IPIs on pSeries when using a kexec
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Daniel Ritz <daniel.ritz-ml@swissonline.ch> says:
The acpi driver suspend/resume patches that went in recently caused a regression
on my box (toshiba tecra 8000 laptop): after resume from swsusp the fan turns on
keeping blowing cold air out of my notebook. before the patches, the fan was off
and would only make noise when required. it's the same thing described in
bugzilla.kernel.org #5000. the acpi suspend/resume patches or at least parts of
them originate in this bug. now the last patch in the report (attach id 8438)
actually fixes the problem - for me and the reporter. this is a trimmed down
version of that patch.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Len Brown <len.brown@intel.com>
Cc: Sanjoy Mahajan <sanjoy@mrao.cam.ac.uk>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During early MD setup (superblock reading), we don't have a personality yet.
But the error-handling code tries to dereference mddev->pers. Fix.
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.
[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ioctl requires CAP_SYS_ADMIN, so sysfs should too. Note that we don't
require CAP_SYS_ADMIN for reading attributes even though the ioctl does.
There is no reason to limit the read access, and much of the information is
already available via /proc/mdstat
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some places we use number (0660) someplaces names (S_IRUGO). Change all
numbers to be names, and change 0655 to be what it should be.
Also make some formatting more consistent.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Though it rarely matters, we should be using 's' rather than r1_bio->sector
here.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment gives more details, but I didn't quite have the sequencing write,
so there was room for races to leave bits unset in the on-disk bitmap for
short periods of time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a device is unplugged, requests are moved from one or two (depending on
whether a bitmap is in use) queues to the main request queue.
So whenever requests are put on either of those queues, we should make sure
the raid5 array is 'plugged'. However we don't. We currently plug the raid5
queue just before putting requests on queues, so there is room for a race. If
something unplugs the queue at just the wrong time, requests will be left on
the queue and nothing will want to unplug them. Normally something else will
plug and unplug the queue fairly soon, but there is a risk that nothing will.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array is started we start one or two threads (two if there is a
reshape or recovery that needs to be completed).
We currently start these *before* the array is completely set up and in
particular before queue->queuedata is set. If the thread actually starts
very quickly on another CPU, we can end up dereferencing queue->queuedata
and oops.
This patch also makes sure we don't try to start a recovery if a reshape is
being restarted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has to be done in ->load_super, not ->validate_super
Without this, hot-adding devices to an array doesn't always
work right - though there is a work around in mdadm-2.5.2 to
make this less of an issue.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have reports of a problem with raid5 which turns out to be because the raid5
device gets stuck in a 'plugged' state. This shouldn't be able to happen as
3msec after it gets plugged it should get unplugged. However it happens
none-the-less. This patch fixes the problem and is a reasonable thing to do,
though it might hurt performance slightly in some cases.
Until I can find the real problem, we should probably have this workaround in
place.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
screen_info.h doesn't have anything to do with the tty layer and shouldn't be
included by tty.h. This patches removes the include and modifies all users to
directly include screen_info.h. struct screen_info is mainly used to
communicate with the console drivers in drivers/video/console. Note that this
patch touches every arch and I have no way of testing it. If there is a
mistake the worst thing that will happen is a compile error.
[akpm@osdl.org: fix arm build]
[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MAX_NR_CONSOLES, fg_console, want_console and last_console are more of a
function of the VT layer than the TTY one. Moving these to vt.h and vt_kern.h
allows all of the framebuffer and VT console drivers to remove their
dependency on tty.h.
[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the warnings about the section mismatches for __init* in the HiSax
driver.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code really means to mask off the high bits, not assign 0xff.
Signed-off-by: Jens Axboe <axboe@suse.de>
Cc: Marcus Meissner <meissner@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's useful to be able to turn off CONFIG_HOTPLUG for compile-coverage testing
and for section-checking coverage. But a few things go and select
CONFIG_HOTPLUG, making it a royal PITA to turn the thing off.
It's only turnable offable if CONFIG_EMBEDDED anyway. So let's make those
things depend on HOTPLUG, not select it.
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
We will reimplement halt-clearing later, when we have periodic
housekeeping routines in place. This will do as a temporary fix, the
EPIPE case has not yet been seen.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An assert statement near the start of handle_irq_noise in the softmac
version of bcm43xx_main.c is there to protect against out of bound
addressing using variable bcm->noisecalc.nr_samples. The arrays in
question have a dimension of 8, thus the value must be < 8.
Signed-Off-By: Larry.Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace acpi_in_resume with a more general hack
to check irqs_disabled() on any kmalloc() from ACPI.
While setting (system_state != SYSTEM_RUNNING) on resume
seemed more general, Andrew Morton preferred this approach.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Make acpi_os_allocate() into an inline function to
allow /proc/slab_allocators to work.
Delete some memset() that could fault on allocation failure.
Signed-off-by: Len Brown <len.brown@intel.com>
cm_sbs_sem is being downed (via acpi_ac_init->acpi_lock_ac_dir) before it is
initialised, with grave results.
- Make it a mutex
- Initialise it
- Make it static
- Clean other stuff up.
Thanks to Paul Drynoff <pauldrynoff@gmail.com> for reporting and testing.
Cc: Rich Townsend <rhdt@bartol.udel.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
No need for video to be always in
No need for ACPI dock driver to be always in
No need for smart battery driver to be always in
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
HOTPLUG_PCI_ACPI depends on ACPI_DOCK
ACPI_IBM_DOCK depends on ACPI_DOCK=n
ACPI_DOCK is EXPERIMENTAL, though that doesn't seem to mean much
Signed-off-by: Len Brown <len.brown@intel.com>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=6716
Doing a sysrq over a serial line into an SMP machine presently deadlocks.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The following patch gets rid of CONFIG_TSI108_BRIDGE. I add UPIO_TSI to
handle IIR and IER register in serial_in and serial_out.
(1) the reason to rewrite serial_in:
TSI108 rev Z1 version ERRATA. Reading the UART's Interrupt
Identification Register (IIR) clears the Transmit Holding Register
Empty (THRE) and Transmit buffer Empty (TEMP) interrupts even if they
are not enabled in the Interrupt Enable Register (IER). This leads to
loss of the interrupts. Interrupts are not cleared when reading UART
registers as 32-bit word.
(2) the reason to rewrite serial_out:
Check for UART_IER_UUE bit in the autoconfig routine. This section
of autoconfig is excluded for Tsi108/109 because bits 7 and 6 are
reserved for internal use. They are R/W bits. In addition to
incorrect identification, changing these bits (from 00) will make
Tsi108/109 UART non-functional.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch below fixes serial console hangs as seen on IP22
machines. Typically, while booting, the machine hangs for ~1 minute
displaying "INIT: ", then the same thing happens again when init
enters in the designated runlevel and finally the getty process on
ttyS0 hangs indefinitely (though strace'ing it helps).
strace (-e raw=ioctl, otherwise the ioctl() translation is utterly
bogus) reveals that getty hangs on ioctl() 0x540f which happens to be
TCSETSW (I saw it hang on another console ioctl() but couldn't
reproduce that one).
A diff between ip22zilog and sunzilog revealed the following
differences:
1. the channel A flag being set on up.port.flags instead of up.flags
2. the channel A flag being set on what is marked as being channel B
3. sunzilog has a call to uart_update_timeout(port, termios->c_cflag, baud);
at the end of sunzilog_set_termios(), which ip22zilog lacks (on
purpose ?)
The patch below addresses point 1 and fixes the serial console hangs
just fine. However point 2 should be investigated by someone familiar
with the IP22 Zilog; it's probably OK as is but even if it is, a
comment in ip22zilog.c is badly needed.
Point 3 is left as an exercise for whoever feels like digging into
ip22zilog :)
These are the main obvious differences between ip22zilog and
sunzilog. Newer versions of sunzilog (Linus's git tree as of today)
are more close to ip22zilog as the sbus_{write,read}b have been
changed into simple {write,read}b, which shrinks the diff by a fair
amount. Resyncing both drivers should be doable in a few hours time
now for someone familiar with the IP22 Zilog hardware.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the following compilation error in the dz serial driver that got
introduced with the "kernel console should send CRLF not LFCR" change.
CC drivers/serial/dz.o
drivers/serial/dz.c: In function 'dz_console_putchar':
drivers/serial/dz.c:679: error: 'uport' undeclared (first use in this function)
drivers/serial/dz.c:679: error: (Each undeclared identifier is reported only once
drivers/serial/dz.c:679: error: for each function it appears in.)
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux mutexes and the debug code that that reference
acpi_os_get_thread_id() are happy with 0.
But the AML mutexes in exmutex.c expect a unique non-zero
number for each thread - as they track this thread_id
to permit the mutex re-entrancy defined by the ACPI spec.
http://bugzilla.kernel.org/show_bug.cgi?id=6687
Signed-off-by: Len Brown <len.brown@intel.com>
Added the ACPI_PACKED_POINTERS_NOT_SUPPORTED macro to
support C compilers that do not allow the initialization
of address pointers within packed structures - even though
the hardware itself may support misaligned transfers. Some
of the debug data structures are packed by default to
minimize size.
Added an error message for the case where
acpi_os_get_thread_id() returns zero. A non-zero value is
required by the core ACPICA code to ensure the proper
operation of AML mutexes and recursive control methods.
The DSDT is now the only ACPI table that determines whether
the AML interpreter is in 32-bit or 64-bit mode. Not really
a functional change, but the hooks for per-table 32/64
switching have been removed from the code. A clarification
to the ACPI specification is forthcoming in ACPI 3.0B.
Fixed a possible leak of an Owner ID in the error
path of tbinstal.c acpi_tb_init_table_descriptor() and
migrated all table OwnerID deletion to a single place in
acpi_tb_uninstall_table() to correct possible leaks when using
the acpi_tb_delete_tables_by_type() interface (with assistance
from Lance Ortiz.)
Fixed a problem with Serialized control methods where the
semaphore associated with the method could be over-signaled
after multiple method invocations.
Fixed two issues with the locking of the internal
namespace data structure. Both the Unload() operator and
acpi_unload_table() interface now lock the namespace during
the namespace deletion associated with the table unload
(with assistance from Linn Crosetto.)
Fixed problem reports (Valery Podrezov) integrated: -
Eliminate unnecessary memory allocation for CreateXxxxField
http://bugzilla.kernel.org/show_bug.cgi?id=5426
Fixed problem reports (Fiodor Suietov) integrated: -
Incomplete cleanup branches in AcpiTbGetTableRsdt (BZ 369)
- On Address Space handler deletion, needless deactivation
call (BZ 374) - AcpiRemoveAddressSpaceHandler: validate
Device handle parameter (BZ 375) - Possible memory leak,
Notify sub-objects of Processor, Power, ThermalZone (BZ
376) - AcpiRemoveAddressSpaceHandler: validate Handler
parameter (BZ 378) - Minimum Length of RSDT should be
validated (BZ 379) - AcpiRemoveNotifyHandler: return
AE_NOT_EXIST if Processor Obj has no Handler (BZ (380)
- AcpiUnloadTable: return AE_NOT_EXIST if no table of
specified type loaded (BZ 381)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently struct scsi_cmnd has various fields that are used to backup
original data after the corresponding fields have been overridden for
EH commands. This means drivers can easily get at it and misuse it.
Due to the old_ naming this doesn't happen for most of them, but two
that have different names have been used wrong a lot (see previous
patch). Another downside is that they unessecarily bloat the scsi_cmnd
size.
This patch moves them onstack in scsi_send_eh_cmnd to fix those two
issues aswell as allowing future EH fixes like moving the EH command
submissions to use SG lists like everything else.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Without this patch we register an interrupt with request_irq,
but then return a bad return code from the module probe.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Allocate the correct number of lp events when running
ibmvscsi on legacy iseries
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove last vestiges of the reverse_scan paramater from aic7xxx and aic79xx.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Stop poking into the old_ & co scsi_cmnd fields that should only be used
in the EH code. Untested, but this is required to move ahead with the
EH fixes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert this:
st0: Error with sense data: <6>st: Current: sense key: Illegal Request
Additional sense: Invalid field in cdb
To this:
st0: Current: sense key: Illegal Request
Additional sense: Invalid field in cdb
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Fixes:
- Fix some sparse warnings - casts of address space
- Fix handling of the adapter registration string. Each invocation
was byteswapping, so every other adapter init attempt failed.
- Correct comments and default value for the lpfc_max_luns parameter
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add lpfc_sli_flush_mbox_queue() function and use it in lpfc_offline() call
to avoid deadlock on thread block.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct the wait in attachment that delays for topology discovery
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This reverts commit a5e1b94008.
Adrian Bunk points out that it has build errors, and apparently no
maintenance. Throw it out.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove depricated sysfs attribute board_online, as it's replaced by the new
issue_reset attribute
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding new issue_reset sysfs attribute
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic in lpfc_sli_validate_fcp_iocb due to access of scsi_cmnd after
returning it to the midlayer
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Consolidate dma buf cleanup into a separate function
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct bogus nodev_tmo message on NPort that changes its NPort Id
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix txcmplq related panics on heavy IO while downloading firmware
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Issue DOWN_LINK prior to INIT_LINK to work around link failure issue
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed infinite retry of REG_LOGIN mailbox failed due to MBXERR_RPI_FULL
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix memory leak and cleanup code related to per ring lookup array.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Standardize the driver on a single define for the maximum supported targets.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use mod_timer instead of add_timer in lpfc_els_timeout_handler
This patch was formerly posted by Mark Haverkamp.
http://marc.theaimsgroup.com/?l=linux-scsi&m=114246089015681&w=2
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This allows us to be rid of the machinery in mptsas for creating and
tracking port numbers. Since mptsas is merely inventing the numbers,
the SAS transport class may as well do it instead.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following on from my post titled: "additional sense codes
need update" see the attachment against lk 2.6.17 .
ChangeLog:
- update additional sense codes table to agree with
SPC-4 revision 5a (14 June 2006)
- adjust some of the opcode names
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some SAS HBAs don't want to go to the trouble of tracking port numbers,
so they'd simply like to say "add this port and give it a number".
This is especially beneficial from the hotplug point of view, since
tracking ports and the available number space can be a real pain.
The current implementation uses an incrementing number per expander to
add the port on. However, since there can never be more ports than
there are phys, a later implementation will try to be more intelligent
about this.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes a needlessly global function static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds the wrapper function skb_is_gso which can be used instead
of directly testing skb_shinfo(skb)->gso_size. This makes things a little
nicer and allows us to change the primary key for indicating whether an skb
is GSO (if we ever want to do that).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Coverity checker spotted, that from the changes from commit
898b1d16f8 the
if (ret)
platform_driver_unregister(&ali_ircc_driver);
was dead code.
This patch changes this function to what seems to have been the
intention.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Charles Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the AMD 8131 bridge to the list of chipsets that reorder writes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ There's some not quite baked bits in cpufreq-git right now
so sending this on as a patch instead ]
On Thu, 2006-07-06 at 07:58 -0700, Tom London wrote:
> After installing .2356 I get this each time I boot:
> =======================================================
> [ INFO: possible circular locking dependency detected ]
> -------------------------------------------------------
> S06cpuspeed/1620 is trying to acquire lock:
> (dbs_mutex){--..}, at: [<c060d6bb>] mutex_lock+0x21/0x24
>
> but task is already holding lock:
> (cpucontrol){--..}, at: [<c060d6bb>] mutex_lock+0x21/0x24
>
> which lock already depends on the new lock.
>
make sure the cpu hotplug recursive mutex (yuck) is taken early in the
cpufreq codepaths to avoid a AB-BA deadlock.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we force the chip into dual fn mode so we get PATA and AHCI we must
be sure we don't then do anything dumb like try and grab both with the AHCI
driver.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This one looks better, IMHO.
This restores the default libata configuration messages printed during booting.
Signed-off-by: <petkov@math.uni-muenster.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out controller initialization from sil24_init_one() into
sil24_init_controller(). This will be used by resume.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out controller initialization from sil_init_one() into
sil_init_controller(). This will be used by resume.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement controller-wide PM. ata_host_set_suspend/resume() are
defined to suspend and resume a host_set. While suspended, EHs for
all ports in the host_set are pegged using ATA_FLAG_SUSPENDED and
frozen.
Because SCSI device hotplug is done asynchronously against the rest of
libata EH and the same mutex is used when adding new device, suspend
cannot wait for hotplug to complete. So, if SCSI device hotplug is in
progress, suspend fails with -EBUSY.
In most cases, host_set resume is followed by device resume. As each
resume operation requires a reset, a single host_set-wide resume
operation may result in multiple resets. To avoid this, resume waits
upto 1 second giving PM to request resume for devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement per-dev PM. The original implementation directly put the
device into suspended mode and didn't synchronize w/ EH operations
including hotplug. This patch reimplements ata_scsi_device_suspend()
and ata_scsi_device_resume() such that they request EH to perform the
respective operations. Both functions synchronize with hotplug such
that it doesn't operate on detached devices.
Suspend waits for completion but resume just issues request and
returns. This allows parallel wake up of devices and thus speeds up
system resume.
Due to sdev detach synchronization, it's not feasible to separate out
EH requesting from sdev handling; thus, ata_device_suspend/resume()
are removed and everything is implemented in the respective
libata-scsi functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement two PM per-dev EH actions - ATA_EH_SUSPEND and
ATA_EH_RESUME. Each action puts the target device into suspended mode
and resumes from it respectively.
Once a device is put to suspended mode, no EH operations other than
RESUME is allowed on the device. The device will stay suspended till
it gets resumed and thus reset and revalidated. To implement this, a
new device state helper - ata_dev_ready() - is implemented and used in
EH action implementations to make them operate only on attached &
running devices.
If all possible devices on a port are suspended, reset is skipped too.
This prevents spurious events including hotplug events from disrupting
suspended devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_EHI_NO_AUTOPSY and QUIET. These used to be implied by
ATA_PFLAG_LOADING, but new power management and PMP support need to
use these separately. e.g. Suspend/resume operations shouldn't print
full EH messages and resume shouldn't be recorded as an error.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The names of predefined debounce timing parameters didn't exactly
match their usages. Rename to more generic names and implement param
selection helper sata_ehc_deb_timing() which uses EHI_HOTPLUGGED to
select params.
Combined with the previous EHI_RESUME_LINK differentiation, this makes
parameter selection accurate. e.g. user scan resumes link but normal
deb param is used instead of hotplug param.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_EHI_RESUME_LINK, which indicates that the link needs to
be resumed. This used to be implied by ATA_EHI_HOTPLUGGED. However,
hotplug isn't the only event which requires link resume and separating
this out allows other places to request link resume. This
differentiation also allows better debounce timing selection.
This patch converts user scan to use ATA_EHI_RESUME_LINK.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ap_lock was used because &ap->host_set->lock was too long and used a
lot. Now that &ap->host_set->lock is replaced with ap->lock, there's
no reason to keep ap_lock.
[ed. note: that's not entirely true. ap_lock is a local variable,
caching the results of a de-ref. In theory, if the compiler is smart
enough, this patch is cosmetic. However, since this is not a fast
path (it is the error path), this patch is nonetheless acceptable,
even though it _may_ introduce a performance regression.]
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_eh_autopsy() used to directly assign determined action mask to
ehc->i.action thus overriding actions set by some of nested analyze
functions. This patch makes ata_eh_autopsy() add action masks just as
it's done in other places.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ap->flags is way too clamped. Separate out core dynamic flags to
ap->pflags. ATA_FLAG_DISABLED is a dynamic flag but left alone as
it's referenced by a lot of LLDs and it's gonna be removed once all
LLDs are converted to new EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In preparation for SAS attached SATA devices, which will
not have a libata scsi_host, only setup host->max_cmd_len
if ap->host exists.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
sata_vsc is an MMIO device, and should use the correct data_xfer
function. This problem was introduced by:
commit a6b2c5d475
Author: Alan Cox <alan@lxorguk.ukuu.org.uk>
Date: Mon May 22 16:59:59 2006 +0100
[PATCH] PATCH: libata. Add ->data_xfer method
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
> stack backtrace:
> [<f9099d31>] rtl8139_start_xmit+0xd9/0xff [8139too]
> [<c11ad5ea>] netpoll_send_skb+0x98/0xea
This seems to be a real deadlock...
So netpoll_send_skb takes the _xmit_lock, which is all nitty gritty
but then rtl8139_start_xmit comes around while that lock is taken, and
does
spin_unlock_irq(&tp->lock);
which.. enables interrupts and softirqs; this is quite bad because the
xmit lock is taken in softirq context for the watchdog like this:
[<c1200376>] _spin_lock+0x23/0x32
[<c11af282>] dev_watchdog+0x14/0xb1
[<c101dab2>] run_timer_softirq+0xf2/0x14a
[<c101a691>] __do_softirq+0x55/0xb0
[<c1004a8d>] do_softirq+0x58/0xbd
Which would deadlock now that the spin_unlock_irq() has enabled
irqs/softirqs while the _xmit_lock is still held.
The patch below turns this into a irqsave/irqrestore pair so that
interrupts don't get enabled unconditionally.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver source code is not the preferred place to store change history.
Acked-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the IRQ line, the tx_boundary, and whether Write-combining and MSI
are enabled to the list of parameters that are exported to ethtool.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Displaying the interface name when listing the device parameters
at the end of myri10ge_probe is not a good idea since udev might
rename the interface soon afterwards.
Print the bus id instead, using dev_info().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The workaround for the AER capability of the nVidia chipset has been
removed, we don't need this PCI id anymore. Drop it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The pm_state field in the myri10ge_priv structure is unused. Drop it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove dead entry from net wan Kconfig and net wan Makefile.. This entry is
left over from 2.4 where synclink used syncppp driver directly. synclink
drivers now use generic HDLC
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- updated MAINTAINERS entry to new format
- updated Jan-Pascal's (ACKed) and my email address
- driver cleanup/modernization (runtime-, not hardware-tested)
[bunk@stusta.de: build fix]
Signed-off-by: Andreas Mohr <andi@lisas.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jan-Pascal van Best <jvbest@qv3pluto.leidenuniv.nl>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Barry K. Nathan reported the following lockdep warning:
[ 197.343948] BUG: warning at kernel/lockdep.c:1856/trace_hardirqs_on()
[ 197.345928] [<c010329b>] show_trace_log_lvl+0x5b/0x105
[ 197.346359] [<c0103896>] show_trace+0x1b/0x20
[ 197.346759] [<c01038ed>] dump_stack+0x1f/0x24
[ 197.347159] [<c012efa2>] trace_hardirqs_on+0xfb/0x185
[ 197.348873] [<c029b009>] _spin_unlock_irq+0x24/0x2d
[ 197.350620] [<e09034e8>] do_tx_done+0x171/0x179 [ns83820]
[ 197.350895] [<e090445c>] ns83820_irq+0x149/0x20b [ns83820]
[ 197.351166] [<c013b4b8>] handle_IRQ_event+0x1d/0x52
[ 197.353216] [<c013c6c2>] handle_level_irq+0x97/0xe1
[ 197.355157] [<c01048c3>] do_IRQ+0x8b/0xac
[ 197.355612] [<c0102d9d>] common_interrupt+0x25/0x2c
this is caused because the ns83820 driver re-enables irq flags
in hardirq context.
While legal in theory, in practice it should only be done if the
hardware is really old and has some very high overhead in its ISR.
(such as PIO IDE)
For modern hardware, running ISRs with irqs enabled is discouraged,
because 1) new hardware is fast enough to not cause latency problems
2) allowing the nesting of hardware interrupts only 'spreads out'
the handling of the current ISR, causing extra cachemisses that would
otherwise not happen. Furthermore, on architectures where ISRs share
the kernel stacks, enabling interrupts in ISRs introduces a much
higher kernel-stack-nesting and thus kernel-stack-overflow risk.
3) not managing irq-flags via the _irqsave / _irqrestore variants
is dangerous: it's easy to forget whether one function nests inside
another, and irq flags might be mismanaged.
In the few cases where re-enabling interrupts in an ISR is considered
useful (and unavoidable), it has to be taught to the lock validator
explicitly (because the lock validator needs the "no ISR ever enables
hardirqs" artificial simplification to keep the IRQ/softirq locking
dependencies manageable).
This teaching is done via the explicit use local_irq_enable_in_hardirq().
On a stock kernel this maps to local_irq_enable(). If the lock validator
is enabled then this does not enable interrupts.
Now, the analysis of drivers/net/ns83820.c's irq flags use: the
irq-enabling in irq context seems intentional, but i dont think it's
justified. Furthermore, the driver suffers from problem #3 above too,
in ns83820_tx_timeout() it disables irqs via local_irq_save(), but
then it calls do_tx_done() which does a spin_unlock_irq(),
re-enabling for a function that does not expect it! While currently
this bug seems harmless (only some debug printout seems to be
affected by it), it's nevertheless something to be fixed.
So this patch makes the ns83820 ISR irq-flags-safe, and cleans up
do_tx_done() use and locking to avoid the ns83820_tx_timeout() bug.
From: Arjan van de Ven <arjan@linux.intel.com>
ns83820_mib_isr takes the misc_lock in IRQ context. All other places that
do this in the ISR already use _irqsave versions, make this consistent at
least. At some point in the future someone should audit the driver to see
if all _irqsave's in the ISR can go away, this is generally an iffy/fragile
proposition though; for now get it safe, simple and consistent.
From: Arjan van de Ven <arjan@linux.intel.com>
ok this is a real driver deadlock:
The ns83820 driver enabled interrupts (by unlocking the misc_lock with
_irq) while still holding the rx_info.lock, which is required to be irq
safe since it's used in the ISR like this:
writel(1, dev->base + IER);
spin_unlock_irq(&dev->misc_lock);
kick_rx(ndev);
spin_unlock_irq(&dev->rx_info.lock);
This is can cause a deadlock if an irq was pending at the first
spin_unlock_irq already, or if one would hit during kick_rx().
Simply remove the first _irq solves this
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More cleanup to pcnet32_loopback_test to release receive buffers if
device is not up. Created common routine to free rx buffers.
Tested ia32 and ppc64
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Suspend the chip if possible rather than stop and discard all tx and rx
frames, when changing the mcast list or entering/leaving promiscuous
mode. Created common pcnet32_suspend routine.
Tested ia32 and ppc64
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix pcnet32_set_ringparam to handle memory allocation errors without
leaving the adapter in an inoperative state and null pointers waiting to
be dereferenced.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On 2006-03-08 Eric Sesterhenn wrote:
converts drivers/net to kzalloc usage.
Don Fry modified it to use netif_msg_drv. Tested ia32 and ppc64.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jon Mason wrote on Thu, 12 Jan 2006 17:07:49 -0600:
This patch adds the PCI_DEVICE macro to the pcnet32 driver.
This has been tested on my opteron with my "trident" adapter.
Don Fry modified it slightly and tested on ia32 and ppc64.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the Cicada 8201 PHY, a.k.a Vitesse VSC8201. This PHY is present on the MPC8349mITX.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are 60+ USB wifi adapters available on the market based on the ZyDAS
ZD1211 chip.
Unlike the predecessor (ZD1201), ZD1211 does not have a hardware MAC, so most
data operations are coordinated by the device driver. The ZD1211 chip sits
alongside an RF transceiver which is also controlled by the driver. Our driver
currently supports 2 RF types, we know of one other available in a few marketed
products which we will be supporting soon.
Our driver also supports the newer revision of ZD1211, called ZD1211B. The
initialization and RF operations are slightly different for the new revision,
but the main difference is 802.11e support. Our driver does not support the
QoS features yet, but we think we know how to use them.
This driver is based on ZyDAS's own GPL driver available from www.zydas.com.tw.
ZyDAS engineers have been responsive and supportive of our efforts, so thumbs
up to them. Additionally, the firmware is redistributable and they have
provided device specs.
This driver has been written primarily by Ulrich Kunitz and myself. Graham
Gower, Greg KH, Remco and Bryan Rittmeyer have also contributed. The
developers of ieee80211 and softmac have made our lives so much easier- thanks!
We maintain a small info-page: http://zd1211.ath.cx/wiki/DriverRewrite
If there is enough time for review, we would like to aim for inclusion in
2.6.18. The driver works nicely as a STA, and can connect to both open and
encrypted networks (we are using software-based encryption for now). We will
work towards supporting more advanced features in the future (ad-hoc, master
mode, 802.11a, ...).
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I recently patched softmac to enable shared key authentication. This small patch
will enable crazy or unfortunate bcm43xx users to use this new capability.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current version of bcm43xx-softmac uses local routines to check
if a channel is valid. As noted in the comments, these routines do
not take any regulatory information into account. This patch converts
the code to use the equivalent routine in ieee80211, which is being
converted to know about regulatory information.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Place the Init-vs-IRQ workaround before any card register
access, because we might not have the wireless core mapped
at all times in init. So this will result in a Machine Check
caused by a bus error.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use Softmac-suggested TX ratecode:
ieee80211softmac_suggest_txrate()
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds device IDs for Symbol LA-4123 and Global Sun Tech
GL24110P to the HostAP PLX driver.
This is not tested with real hardware, but there is no reason why it
shouldn't work.
Please test.
Signed-off-by: Faidon Liambotis <faidon@cube.gr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For messages prior to register_netdev(), prefer dev_printk() because
that prints out both our driver name and our [PCI | whatever] bus id.
Updates: 8139{cp,too}, b44, bnx2, cassini, {eepro,epic}100, fealnx,
hamachi, ne2k-pci, ns83820, pci-skeleton, r8169.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- const-ify pci_device_id table
- clean up pci_device_id table with PCI_DEVICE()
- don't store internal pointer in pci_device_id table,
use pci_device_id::driver_data as an integer index
- use dev_printk() for messages where eth%d prefix is unavailable
- formatting fixes
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Becker-derived drivers often have the 'io_size' member in their chip
info struct, indicating the minimum required size of the I/O resource
(usually a PCI BAR). For many situations, this number is either
constant or irrelevant (due to pci_iomap convenience behavior).
This change removes the io_size invariant member, and replaces it with a
compile-time constant.
Drivers updated: fealnx, gt96100eth, winbond-840, yellowfin
Additionally,
- gt96100eth: unused 'drv_flags' removed from gt96100eth
- winbond-840: unused struct match_info removed
- winbond-840: mark pci_id_tbl[] const, __devinitdata
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When in-kernel net drivers branched from Donald Becker's vanilla driver
set, in the days before BitKeeper and git, a driver changelog was
maintained in the driver source code. These days, the kernel's
changelog is far superior and much more accurate, so the in-driver
changelogs are removed.
Another relic of the Becker/kernel split was version numbering, using
"foo-LKx.y.z" notation, resulting in weird version numbers like
"1.17b-LK1.1.9". These drivers are for older hardware, and see few
changes these days, so the version numbers were all bumped to something
more simple.
Finally, in xircom_tulip_cb specifically, an additional cleanup removes
the always-enabled CARDBUS cpp macro.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Remove in-source changelog, it's in the global kernel history.
- convert silly and useless version to useful one
- replace invariant pci_id_tbl[]::io_size uses with EPIC_TOTAL_SIZE
- remove now-unused io_size member from pci_id_tbl[]
- current kernel style prefers dev_printk() for the rare ethernet driver
messages that cannot print an 'eth%d' prefix.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from Andrew Victor
The AT91RM9200 errata work-around should be using the GPIO API and not
accessing the PIO registers directly.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
Move workqueue exports to where the functions are defined.
[CPUFREQ] Misc cleanups in ondemand.
[CPUFREQ] Make ondemand sampling per CPU and remove the mutex usage in sampling path.
[CPUFREQ] Add queue_delayed_work_on() interface for workqueues.
[CPUFREQ] Remove slowdown from ondemand sampling path.
mthca: initialize send and receive queue locks separately
lockdep identifies a lock by the call site of its initialization. By
initializing the send and receive queue locks in mthca_wq_init() we confuse
lockdep. It warns that that the ordered acquiry of both locks in
mthca_modify_qp() is recursive acquiry of one lock:
=============================================
[ INFO: possible recursive locking detected ]
---------------------------------------------
modprobe/1192 is trying to acquire lock:
(&wq->lock){....}, at: [<f892b4db>] mthca_modify_qp+0x60/0xa7b [ib_mthca]
but task is already holding lock:
(&wq->lock){....}, at: [<f892b4ce>] mthca_modify_qp+0x53/0xa7b [ib_mthca]
Initializing the locks separately in mthca_alloc_qp_common() stops the
warning and will let lockdep enforce proper ordering on paths that acquire
both locks.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Ensure 8250_pci quirks are not marked __devinit
[SERIAL] Convert fifosize to an unsigned int
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
[Bluetooth] Add RFCOMM role switch support
[Bluetooth] Allow disabling of credit based flow control
[Bluetooth] Small cleanup of the L2CAP source code
[Bluetooth] Use real devices for host controllers
[Bluetooth] Add platform device for virtual and serial devices
[Bluetooth] Add automatic sniff mode support
[Bluetooth] Correct SCO buffer size on request
[Bluetooth] Add suspend/resume support to the HCI USB driver
[Bluetooth] Use raw mode for the Frontline sniffer device
[BRIDGE]: br_dump_ifinfo index fix
[ATM]: add+use poison defines
[NET]: add+use poison defines
[IOAT]: fix kernel-doc in source files
[IOAT]: fix header file kernel-doc
[TG3]: Add ipv6 TSO feature
[IPV6]: Fix ipv6 GSO payload length
[TIPC] Fixed sk_buff panic caused by tipc_link_bundle_buf (REVISED)
[NET]: Verify gso_type too in gso_segment
[IPVS]: Add sysctl documentation
[ROSE]: Try all routes when establishing a ROSE connections.
...
This patch adds a generic Bluetooth platform device that can be used
as parent device by virtual and serial devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
