Move the following functions forward.
r8152_mmd_indirect()
r8152_mmd_read()
r8152_mmd_write()
r8152_eee_en()
r8152b_enable_eee()
r8153_eee_en()
r8153_enable_eee()
r8152b_enable_fc()
r8153_aldps_en()
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing check for 25G and 100G while checking port speed,
which lead to less number of queues getting allocated for 25G & 100G
adapters and leading to low throughput. Adding the missing check for
both NIC and vNIC driver.
Also fixes port advertisement for 25G and 100G in ethtool output.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJX3/GcAAoJED07qiWsqSVq9PgH/jucrHh2H7IAnJi6ZasZmu1t
+beOkzg954rJfz2cGulhpNBAl9xJYRhPuJ+Jw5JhDEPXVisgeRVm6lT+8YJaCsWL
utTotzyRYI3HUrXIl6V2rjn1ms7TAlZsHrAGPj1ufJKEZg8/SF5C15NuY9YTlh4d
JZT0V13Yxj0CV3d2jqZshFXrF+CiAsGyQF1aGA9Wo2xQeZIt2vY/1DfNtC9eXlXW
+t7tBCgLka7cwTBC513BKjl9fGwzYO0eYU993N9+Ijir6HLM9N3igZwxjH1hEl/S
ow6n5T1O89JEnghSN5Xq+2ThkkXR7zZwi+6l74eFICkIwHK/pekZ8dPr9Ct9ZZ0=
=JcjG
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.8-20160919' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-09-19
this is a pull request of one patch for the upcoming linux-4.8 release.
The patch by Fabio Estevam fixes the pm handling in the flexcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fe56b9e6a8 ("qed: Add module with basic common support")
has introduced a stack corruption during probe, where filling a
local struct with data to be sent to management firmware is incorrectly
filled; The data is written outside of the struct and corrupts
the stack.
Changes from v1:
----------------
- Correct the value written [Caught by David Laight]
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core distributed switch architecture code currently does not have
a MAINTAINERS entry, which results in some contributions not landing
in the right peoples inbox.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8c14586fc3 ("net: ipv6: Use passed in table for nexthop
lookups") introduced a regression: insertion of an IPv6 route in a table
not containing the appropriate connected route for the gateway but which
contained a non-connected route (like a default gateway) fails while it
was previously working:
$ ip link add eth0 type dummy
$ ip link set up dev eth0
$ ip addr add 2001:db8::1/64 dev eth0
$ ip route add ::/0 via 2001:db8::5 dev eth0 table 20
$ ip route add 2001:db8:cafe::1/128 via 2001:db8::6 dev eth0 table 20
RTNETLINK answers: No route to host
$ ip -6 route show table 20
default via 2001:db8::5 dev eth0 metric 1024 pref medium
After this patch, we get:
$ ip route add 2001:db8:cafe::1/128 via 2001:db8::6 dev eth0 table 20
$ ip -6 route show table 20
2001:db8:cafe::1 via 2001:db8::6 dev eth0 metric 1024 pref medium
default via 2001:db8::5 dev eth0 metric 1024 pref medium
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
mlx5 fixes to 4.8-rc6
This series series has a fix from Roi to memory corruption bug in
the bulk flow counters code and two late and hopefully last fixes
from me to the new eswitch offloads code.
Series done over net commit 37dd348 "bna: fix crash in bnad_get_strings()"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
E-switch mode changes involve creating HW tables, potentially allocating
netdevices, etc, and things can fail. Add an attempt to rollback to the
existing mode when changing to the new mode fails. Only if rollback fails,
getting proper SRIOV functionality requires module unload or sriov
disablement/enablement.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enablement of the SRIOV e-switch in certain mode (switchdev or legacy)
fails, we must set the mode to none. Otherwise, we'll run into double free
based crashes when further attempting to deal with the e-switch (such
as when disabling sriov or unloading the driver).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FW command output length should be only the length of struct
mlx5_cmd_fc_bulk out field. Failing to do so will cause the memcpy
call which is invoked later in the driver to write over wrong memory
address and corrupt kernel memory which results in random crashes.
This bug was found using the kernel address sanitizer (kasan).
Fixes: a351a1b03b ('net/mlx5: Introduce bulk reading of flow counters')
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a imx6ul-pico board the following error is seen during system suspend:
dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* reject aggregation sessions for TSID/TID 8-16 that we
can never use anyway and which could confuse drivers
* check return value of skb_linearize()
-----BEGIN PGP SIGNATURE-----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=3dek
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Two more fixes:
* reject aggregation sessions for TSID/TID 8-16 that we
can never use anyway and which could confuse drivers
* check return value of skb_linearize()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC devices use the RWKPKTEN and MGKPKTEN bits of the PMT Control/Status
register to generate power management events.
So this patch is to properly set the RWKPKTEN [BIT(2)] inside the
PMT register (needed in case of global unicast).
Reported-by: Aditi SHARMA <aditi-hed.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6e7333d "net: add rx_nohandler stat counter" added the new entry
rx_nohandler into struct rtnl_link_stats64. Unfortunately the bna
driver foolishly depends on the structure. It uses part of it for
ethtool statistics and it's not bad but the driver assumes its size
is constant as it defines string for each existing entry. The problem
occurs when the structure is extended because you need to modify bna
driver as well. If not any attempt to retrieve ethtool statistics results
in crash in bnad_get_strings().
The patch changes BNAD_ETHTOOL_STATS_NUM so it counts real number of
strings in the array and also removes rtnl_link_stats64 entries that
are not used in output and are always zero.
Fixes: 6e7333d "net: add rx_nohandler stat counter"
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ba5ca784 "bna: check for dma mapping errors" added besides other
things a statistic that counts number of DMA buffer mapping failures
per each Rx queue. This counter is not included in ethtool stats output.
Fixes: ba5ca784 "bna: check for dma mapping errors"
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function actually operates on u32 yet its paramteres were declared
as u16, causing integer truncation upon calling.
Note in patch context that ADDIP_SERIAL_SIGN_BIT is already 32 bits.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb is not freed if newsk is NULL. Rework the error path so free_skb is
unconditionally called on function exit.
Fixes: c3ea9fa274 ("[IrDA] af_irda: IRDA_ASSERT cleanups")
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious TCP receiver, sending SACK, can force the sender to split
skbs in write queue and increase its memory usage.
Then, when socket is closed and its write queue purged, we might
overflow sk_forward_alloc (It becomes negative)
sk_mem_reclaim() does nothing in this case, and more than 2GB
are leaked from TCP perspective (tcp_memory_allocated is not changed)
Then warnings trigger from inet_sock_destruct() and
sk_stream_kill_queues() seeing a not zero sk_forward_alloc
All TCP stack can be stuck because TCP is under memory pressure.
A simple fix is to preemptively reclaim from sk_mem_uncharge().
This makes sure a socket wont have more than 2 MB forward allocated,
after burst and idle period.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a TCP socket gets a large write queue, an overflow can happen
in a test in __tcp_retransmit_skb() preventing all retransmits.
The flow then stalls and resets after timeouts.
Tested:
sysctl -w net.core.wmem_max=1000000000
netperf -H dest -- -s 1000000000
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error during netback_probe() (e.g. an entry missing on the
xenstore) netback_remove() is called on the new device, which will set
the device backend state to XenbusStateClosed by calling
set_backend_state(). However, the backend state wasn't initialized by
netback_probe() at this point, which will cause and invalid transaction
and set_backend_state() to BUG().
Initialize the backend state at the beginning of netback_probe() to
XenbusStateInitialising, and create two new valid state transitions on
set_backend_state(), from XenbusStateInitialising to XenbusStateClosed,
and from XenbusStateInitialising to XenbusStateInitWait.
Signed-off-by: Filipe Manco <filipe.manco@neclab.eu>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
390: qeth patches
here are several fixes for the s390 qeth driver, built for net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
restructured the internal address handling.
This work broke setting a virtual IP address.
The command
echo 10.1.1.1 > /sys/bus/ccwgroup/devices/<device>/vipa/add4
fails with file exist error even if the IP address has not
been set before.
It turned out that the search result for the IP address
search is handled incorrectly in the VIPA case.
This patch fixes the setting of an virtual IP address.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to recent performance measurements, turning on net_device
feature NETIF_F_SG only behaves well, but turning on feature
NETIF_F_GSO shows bad results. Since the kernel activates NETIF_F_GSO
automatically as soon as the driver configures feature NETIF_F_SG, qeth
should not activate feature NETIF_F_SG per default, until the qeth
problems with NETIF_F_GSO are solved.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reduce the need of skb_linearize() calls, gso_max_segs of qeth
net_devices had been limited according to the maximum number of qdio SBAL
elements. But a gso segment cannot be larger than the mtu-size, while an
SBAL element can contain up to 4096 bytes. The gso_max_segs limitation
limits the maximum packet size given to the qeth driver. Performance
measurements with tso-enabled qeth network interfaces and mtu-size 1500
showed, that the disadvantage of smaller packets is much more severe than
the advantage of fewer skb_linearize() calls.
This patch gets rid of the gso_max_segs limitations in the qeth driver.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qeth IP address mapping logic has been reworked recently. It
causes now problems to specify qeth sysfs attribute "hsuid" in DOWN
state, which is allowed. Postpone registering or deregistering of
IP-addresses in this case.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l3_dev_hsuid_store() changes the ip hash table, which
requires the ip_lock.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After device recovery, only a basic set of network device features is
enabled on the device. If features like checksum offloading or TSO were
enabled by the user before the recovery, this results in a mismatch
between the network device features, that the kernel assumes to be
enabled on the device, and the features actually enabled on the device.
This patch tries to restore previously set features, that require
changes on the device, after the recovery of a device. In case of an
error, the network device's features are changed to contain only the
features that are actually turned on.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 73725d9dfd ("nfp: allocate ring SW structs dynamically")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ip_rcv_finish() calls l3mdev_ip_rcv(). On any VRF except
the global VRF, this replaces skb->dev with the VRF master interface.
When calling ip_route_input_noref() from here, the checks for forwarding
look at this master device instead of the initial ingress interface.
This will allow packets to be routed which normally would be dropped.
For example, an interface that is not assigned an IP address should
drop packets, but because the checking is against the master device, the
packet will be forwarded.
The fix here is to still call l3mdev_ip_rcv(), but remember the initial
net_device. This is passed to the other functions within ip_rcv_finish,
so they still see the original interface.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for preventing race conditions within ioctl calls.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add realization for mac address set and remove dummy callback.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device table is required to load modules based on
modaliases. After adding MODULE_DEVICE_TABLE, below entries
for example will be added to modules.alias:
alias of:N*T*Cmediatek,mt7623-ethC* mtk_eth_soc
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix reference counting for last_bonding_candidate, by Sven Eckelmann
- Fix head room reservation for ELP packets, by Linus Luessing
-----BEGIN PGP SIGNATURE-----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=mHPX
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20160914' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfix patches:
- Fix reference counting for last_bonding_candidate, by Sven Eckelmann
- Fix head room reservation for ELP packets, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs in mlx4_init_eq_table the index used in the
err_out_unmap label is one too big which results in a panic in
mlx4_free_eq. This patch fixes the index in the error path.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* better mesh path fixing, from Thomas
* fix TIM IE recalculation after sending frames
to a sleeping station, from Felix
* fix sequence number assignment while sending
frames to a sleeping station, also from Felix
* validate number of probe response CSA counter
offsets, fixing a copy/paste bug (from myself)
-----BEGIN PGP SIGNATURE-----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=xzhM
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more fixes:
* better mesh path fixing, from Thomas
* fix TIM IE recalculation after sending frames
to a sleeping station, from Felix
* fix sequence number assignment while sending
frames to a sleeping station, also from Felix
* validate number of probe response CSA counter
offsets, fixing a copy/paste bug (from myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mac80211 doesn't currently support TSIDs 8-15 which can
only be used after QoS TSPEC negotiation (and not even after
WMM negotiation), reject attempts to set up aggregation
sessions for them, which might confuse drivers. In mac80211
we do correctly handle that, but the TSIDs should never get
used anyway, and drivers might not be able to handle it.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The A-MSDU TX code (within TXQs) didn't always check the return value
of skb_linearize() properly, resulting in potentially passing a frag-
list SKB down to the driver even when it said it can't handle it. Fix
that.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to an apparent copy/paste bug, the number of counters for the
beacon configuration were checked twice, instead of checking the
number of probe response counters. Fix this to check the number of
probe response counters before parsing those.
Cc: stable@vger.kernel.org
Fixes: 9a774c78e2 ("cfg80211: Support multiple CSA counters")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If 'IS_ERR(pdata->clk)' is true, then 'clk_disable_unprepare(pdata->clk)'
will do nothing.
It is likely that 'if (!IS_ERR(pdata->clk))' was expected here.
In fact, the test can even be removed because 'clk_disable_unprepare'
already handles such cases.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 4f00878126 ("sctp: apply rhashtable api to send/recv
path"), sctp uses transport rhashtable with .obj_cmpfn sctp_hash_cmp,
in which it compares the members of the transport with the rhashtable
args to check if it's the right transport.
But sctp uses the transport without holding it in sctp_hash_cmp, it can
cause a use-after-free panic. As after it gets transport from hashtable,
another CPU may close the sk and free the asoc. In sctp_association_free,
it frees all the transports, meanwhile, the assoc's refcnt may be reduced
to 0, assoc can be destroyed by sctp_association_destroy.
So after that, transport->assoc is actually an unavailable memory address
in sctp_hash_cmp. Although sctp_hash_cmp is under rcu_read_lock, it still
can not avoid this, as assoc is not freed by RCU.
This patch is to hold the transport before checking it's members with
sctp_transport_hold, in which it checks the refcnt first, holds it if
it's not 0.
Fixes: 4f00878126 ("sctp: apply rhashtable api to send/recv path")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system enters into kdump kernel because of kernel panic, it won't
shutdown devices. On-flight DMA will continue transferring data until
device driver initializes. All devices are supposed to reset during
driver initialization. And this property is used to fix the kdump
failure in system with intel iommu. Other systems with hardware iommu
should be similar. Please check commit 091d42e ("iommu/vt-d: Copy
translation tables from old kernel") and those commits around.
But bnx2 driver doesn't reset device during driver initialization. The
device resetting is deferred to net device up stage. This will cause
hardware iommu handling failure on bnx2 device. And its resetting relies
on firmware. So in this patch move the firmware requesting code to earlier
bnx2_init_one(), then next call bnx2_reset_chip to reset device.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Endianess fix for the new nf_tables netlink trace infrastructure,
NFTA_TRACE_POLICY endianess was not correct, patch from Liping Zhang.
2) Fix broken re-route after userspace queueing in nf_tables route
chain. This patch is large but it is simple since it is just getting
this code in sync with iptable_mangle. Also from Liping.
3) NAT mangling via ctnetlink lies to userspace when nf_nat_setup_info()
fails to setup the NAT conntrack extension. This problem has been
there since the beginning, but it can now show up after rhashtable
conversion.
4) Fix possible NULL pointer dereference due to failures in allocating
the synproxy and seqadj conntrack extensions, from Gao feng.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When memory is exhausted, nfct_seqadj_ext_add may fail to add the
synproxy and seqadj extensions. The function nf_ct_seqadj_init doesn't
check if get valid seqadj pointer by the nfct_seqadj.
Now drop the packet directly when fail to add seqadj extension to
avoid dereference NULL pointer in nf_ct_seqadj_init from
init_conntrack().
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_nat_setup_info() returns NF_* verdicts, so convert them to error
codes that is what ctnelink expects. This has passed overlook without
having any impact since this nf_nat_setup_info() has always returned
NF_ACCEPT so far. Since 870190a9ec ("netfilter: nat: convert nat bysrc
hash to rhashtable"), this is problem.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
"Mostly small sets of driver fixes scattered all over the place.
1) Mediatek driver fixes from Sean Wang. Forward port not written
correctly during TX map, missed handling of EPROBE_DEFER, and
mistaken use of put_page() instead of skb_free_frag().
2) Fix socket double-free in KCM code, from WANG Cong.
3) QED driver fixes from Sudarsana Reddy Kalluru, including a fix for
using the dcbx buffers before initializing them.
4) Mellanox Switch driver fixes from Jiri Pirko, including a fix for
double fib removals and an error handling fix in
mlxsw_sp_module_init().
5) Fix kernel panic when enabling LLDP in i40e driver, from Dave
Ertman.
6) Fix padding of TSO packets in thunderx driver, from Sunil Goutham.
7) TCP's rcv_wup not initialized properly when using fastopen, from
Neal Cardwell.
8) Don't use uninitialized flow keys in flow dissector, from Gao
Feng.
9) Use after free in l2tp module unload, from Sabrina Dubroca.
10) Fix interrupt registry ordering issues in smsc911x driver, from
Jeremy Linton.
11) Fix crashes in bonding having to do with enslaving and rx_handler,
from Mahesh Bandewar.
12) AF_UNIX deadlock fixes from Linus.
13) In mlx5 driver, don't read skb->xmit_mode after it might have been
freed from the TX reclaim path. From Tariq Toukan.
14) Fix a bug from 2015 in TCP Yeah where the congestion window does
not increase, from Artem Germanov.
15) Don't pad frames on receive in NFP driver, from Jakub Kicinski.
16) Fix chunk fragmenting in SCTP wrt. GSO, from Marcelo Ricardo
Leitner.
17) Fix deletion of VRF routes, from Mark Tomlinson.
18) Fix device refcount leak when DAD fails in ipv6, from Wei Yongjun"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
net/mlx4_en: Fix panic on xmit while port is down
net/mlx4_en: Fixes for DCBX
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_state()
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_all()
net: ethernet: renesas: sh_eth: add POST registers for rz
drivers: net: phy: mdio-xgene: Add hardware dependency
dwc_eth_qos: do not register semi-initialized device
sctp: identify chunks that need to be fragmented at IP level
mlxsw: spectrum: Set port type before setting its address
mlxsw: spectrum_router: Fix error path in mlxsw_sp_router_init
nfp: don't pad frames on receive
nfp: drop support for old firmware ABIs
nfp: remove linux/version.h includes
tcp: cwnd does not increase in TCP YeAH
net/mlx5e: Fix parsing of vlan packets when updating lro header
net/mlx5e: Fix global PFC counters replication
net/mlx5e: Prevent casting overflow
net/mlx5e: Move an_disable_cap bit to a new position
net/mlx5e: Fix xmit_more counter race issue
tcp: fastopen: avoid negative sk_forward_alloc
...
A fixed mpath was not quite being treated as such:
1) if a PERR frame was received, a fixed mpath was
deactivated.
2) queued path discovery for fixed mpath was potentially
being considered, changing mpath state.
3) other mpath flags were potentially being inherited when
fixing the mpath. Just assign PATH_FIXED and SN_VALID.
This solves several issues when fixing a mesh path in one
direction. The reverse direction mpath should probably
also be fixed, or root announcements at least be enabled.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using intermediate queues, sequence number allocation is deferred
until dequeue. This doesn't work for PS response frames, which bypass
those queues.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Handle the case where the mac80211 intermediate queues are empty and the
driver has buffered frames
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
