For some odd reason, the plink_state enum is
declared in the middle between aggregation
related structures. Move it down to make the
file easier to read.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After ieee80211_rx_h_ctrl() processing we only
want to process management (including action)
frames, so there's no point in letting control
frames continue.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since we use only cfg80211 for configuration,
there is no configuration that could be pending at
this point, cfg80211 will have the configuration
that is pending and apply it afterwards.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I suspect the compiler will do this optimisation
anyway, but it seems cleaner to move this into
the WEP switch case.
Also make rx_h_decrypt use a local variable for
the frame_control so that we don't need to reload
the hdr variable for this after linearizing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.
The debugfs code I recently added got this wrong
as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware allow extended filtering of ARP frames not intended for
the host. To perform such filtering, the hardware needs to know the current
IP address(es) of the host, bound to its interface.
Add support for ARP filtering to mac80211 by adding a new op to the driver
interface, allowing to configure the current IP addresses. This op is called
upon association with the currently configured address(es), and when
associated whenever the IP address(es) change.
This patch adds configuration of IPv4 addresses only, as IPv6 addresses don't
need ARP filtering.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a single use of this struct member, but
as it is write-only it clearly not necessary.
Thus we can free up some space here, even if we
don't need it right now it seems pointless to
carry around the variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS code has a bogus mod_timer(..., 0) call,
we shouldn't ever pass a constant value to the
function since any constant value could be in the
future or the past.
However, invoking the timer here is not necessary
at all, since we just finished scanning and just
need to have the IBSS code run again from the
workqueue later, so factor out the work starting
and use that instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the buggy 'ath9k: Group Key fix for VAPs' change.
For AP mode group keys, use the BSSID as lookup mac address, with
the multicast keysearch bit set.
For IBSS mode, use the peer's MAC address with multicast keysearch.
For STA mode, keep using the group key slots.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a MAC address for a key table entry is flagged with the
multicast bit (0x01), indicate to the hardware that multicast
lookup instead of unicast lookup should be used. The multicast
bit itself never makes it to the actual keytable entry register,
as it is shifted out.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit a2064b7a4a.
when CONFIG_IWLAGN=n:
drivers/net/wireless/iwlwifi/iwl-rx.c:254: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:303: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:304: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:305: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:306: error: 'struct iwl_priv' has no member named '_agn'
and many more.
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn-debugfs.c
drivers/net/wireless/iwlwifi/iwl-debugfs.c
drivers/net/wireless/iwlwifi/iwl-dev.h
drivers/net/wireless/iwlwifi/iwl-rx.c
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove suspicious register write as the reg variable is never filled
with an TX_SW_CFG2 associated value before.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
In case of mcs rates txrate->idx contains the mcs index to be used for
transmission. Previously the mcs values dedicated for legacy rates where
used for mcs transmissions which resulted in the use of mcs 0 in a number
of cases (e.g. for all mcs rates >= 15 as rt2x00 does not register legacy
rates with indexes >= 15).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Update TX_SW_CFG initvals for 305x SoC to match with the appropriate
legacy driver.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Use the IEEE80211_TX_CTL_STBC flag to determine the
correct value to be used for the STBC field in the
TX descriptor
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Disable TX STBC for 1 stream devices as a minimum of 2 streams is needed for TX STBC.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Closer inspection of the legacy Ralink driver reveals that in case of HT40+
or HT40- we must adjust the frequency settings that we program to the device.
Implement the same adjustment in the rt2x00 code.
With this HT40 seems to work for all devices supported by rt2800pci and
rt2800usb.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Latest versions of the Ralink rt2800 family drivers use 0 as the token value,
not 0xff.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
This prevents us having common code depend on PCI or USB specific code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Instead of parsing the EEPROM information, use the flag that was set during
device initialization.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Needed later for PCI-express specific code in rt2800pci.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
There is no point on having them separated across 3 files.
At the same time rename USB_CYC_CFG to its proper name US_CYC_CNT
(as per the datasheet).
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
There is no evidence, either in adapters or in the Ralink code, that such
a device actually exists. All so-call RT2870 adapter identify themselves
as RT2860.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
The beacon writing functions of rt2800pci and rt2800usb are now identical.
Move them to rt2800lib to only have one central function.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
There is no need to force the separation between a buffer USB vendor
request that does fit the CSR cache and one that doesn't onto the
callers. This is something that the rt2x00usb_vendor_request_buff
function can figure out by itself.
Combine the rt2x00usb_vendor_request_buff and
rt2x00usb_vendor_request_large_buff functions into a single one, as
both of them were equivalent for small buffers anyway.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Instead of fiddling with the skb->data pointer and thereby risking
out of bounds accesses, properly reserve the space needed in an
skb for descriptors.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
For rt2800 reverse the calling order of rt2x00pci_write_data and
rt2800pci_write_data. Currently rt2800pci_write_data calls rt2x00pci_write_data
as there can be only 1 driver callback function specified by the driver.
Reverse this calling order by introducing a new driver callback function,
called write_tx_datadesc, which is called from the bus-specific write_tx_data
functions.
Preparation for futher cleanups in the skb data handling of rt2x00.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Not all the devices require a TX descriptor to be written (i.e. rt2800
device don't require them). Push down the creation of the TX descriptor
to the device drivers so that they can decide for themselves whether
a TX descriptor is to be created.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
The 5GHz bands were scanned without the proper IE's in place, preventing
proper 5GHz scanning. This patches fixes the problem by storing a pointer
to the scan request (with the IE's) for all iterations of scan.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A fixed 1 mbps rate was used for the PSM entry/exit null-func frames. Fix this
by using the basic rates instead.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The core wl1271 module can also be used with SDIO, so it should not depend on
SPI_MASTER.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 changes to idle almost immediately after transmitting some
frames, such as deauth etc. When going to idle, the wl1271 is disconnected,
which causes TX frames already on buffers, but not yet transmitted, to be
deleted.
To make sure deauth frames reach the air, allow the TX buffers to flush
before proceeding to idle.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As there is more and more stuff triggered by going in and out of idle,
create a separate function for handling that.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 uses a session counter in CMD_JOIN and TX frame descriptors. This
counter is used to determine which frames to drop when the CMD_JOIN is
executed.
The driver executes CMD_JOIN multiple times upon association and sometimes
disassociation, and we don't want any frames to get lost.
Fix this by incrementing the session counter only when leaving idle (not every
CMD_JOIN as before.) Also, remove the TX flush flag from the CMD_JOIN options.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We dereference "wmi" on the line before and also when we initialize "ah".
This check has always been after a dereference since the first commit a
couple months ago. Looking through the code, it looks like "wmi" can't
actually be null here so I just removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use memdup_user when user data is immediately copied into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rx status length should also be taken into account while
validating the length of a received frame.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip the rx status portion in skb->data before accessing ieee80211
frame header.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_rx_skb_preprocess() needs only ieee80211 frame header,
pass only frame headers instead of skb to that function. Also
remove ineffective frame dump in ath9k_process_rate().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A bunch of data structures are present in the
common module, which are internal to ath9k.
Move them to ath9k.h
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch relocates RX processing code from the
common module to ath9k. This reduces the size
of the common module which is also used by ath9k_htc.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To enable it we now disable and re-enable the PHY chips
after TX IQ calibration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending action frames, we want to verify
that we do that on the correct channel. However,
checking the channel type in addition can get in
the way, since the channel type could change on
the fly during an association, and it's not
useful to have the channel type anyway since it
has no effect on the transmission. Therefore,
make it optional to specify so that if wanted,
it can still be checked, but is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
