commit 868ddfcef31ff93ea8961b2e81ea7fe12f6f144b upstream.
The code for hdac_ext_stream seems inherited from hdac_stream, and
similar locking issues are present: the use of the bus->reg_lock
spinlock is inconsistent, with only writes to specific fields being
protected.
Apply similar fix as in hdac_stream by protecting all accesses to
'link_locked' and 'decoupled' fields, with a new helper
snd_hdac_ext_stream_decouple_locked() added to simplify code
changes.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210924192417.169243-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef775a0e36c6a81c5b07cb228c02f967133fe768 upstream.
When CONFIG_PROC_FS is not set, there is a build warning (turned
into an error):
../drivers/hwmon/dell-smm-hwmon.c: In function 'i8k_init_procfs':
../drivers/hwmon/dell-smm-hwmon.c:624:24: error: unused variable 'data' [-Werror=unused-variable]
struct dell_smm_data *data = dev_get_drvdata(dev);
Make I8K depend on PROC_FS and HWMON (instead of selecting HWMON -- it
is strongly preferred to not select entire subsystems).
Build tested in all possible combinations of SENSORS_DELL_SMM, I8K, and
PROC_FS.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lkml.kernel.org/r/20210910071921.16777-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54fde91f52f515e0b1514f0f0fa146e87a672227 upstream.
Christoph pointed out that I'm updating bdev->bd_inode for the device
time when we remove block devices from a btrfs file system, however this
isn't actually exposed to anything. The inode we want to update is the
one that's associated with the path to the device, usually on devtmpfs,
so that blkid notices the difference.
We still don't want to do the blkdev_open, so use kern_path() to get the
path to the given device and do the update time on that inode.
Fixes: 8f96a5bfa150 ("btrfs: update the bdev time directly when closing")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e60feb445fce9e51c1558a6aa7faf9dd5ded533b upstream.
If you already have an inode and need to update the time on the inode
there is no way to do this properly. Export this helper to allow file
systems to update time on the inode so the appropriate handler is
called, either ->update_time or generic_update_time.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ff04286a9569675948f39cec2c6ad47c3584633 upstream.
PF pointer is always valid when PCI core calls its .shutdown() and
.remove() callbacks. There is no need to check it again.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc153aba3ef371d0d76eb88230ed4e0dee5b38f2 upstream.
Instead of maintaining a single-linked list of devices that must be
searched linearly in .remove() just use spi_set_drvdata() to remember the
link between the spi device and the driver struct. Then the global list
and the next member can be dropped.
This simplifies the driver, reduces the memory footprint and the time to
search the list. Also it makes obvious that there is always a corresponding
driver struct for a given device in .remove(), so the error path for
!max3421_hcd can be dropped, too.
As a side effect this fixes a data inconsistency when .probe() races with
itself for a second max3421 device in manipulating max3421_hcd_list. A
similar race is fixed in .remove(), too.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211018204028.2914597-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 827b0913a9d9d07a0c3e559dbb20ca4d6d285a54 upstream.
The recent fix for DAPM to correct the kctl change notification by the
commit 5af82c81b2c4 ("ASoC: DAPM: Fix missing kctl change
notifications") caused other regressions since it changed the behavior
of snd_soc_dapm_set_pin() that is called from several API functions.
Formerly it returned always 0 for success, but now it returns 0 or 1.
This patch addresses it, restoring the old behavior of
snd_soc_dapm_set_pin() while keeping the fix in
snd_soc_dapm_put_pin_switch().
Fixes: 5af82c81b2c4 ("ASoC: DAPM: Fix missing kctl change notifications")
Reported-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211105090925.20575-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc27f3c5d10c58069672215787a96b4fae01818b upstream.
When the hash table slot array allocation fails in hashtab_init(),
h->size is left initialized with a non-zero value, but the h->htable
pointer is NULL. This may then cause a NULL pointer dereference, since
the policydb code relies on the assumption that even after a failed
hashtab_init(), hashtab_map() and hashtab_destroy() can be safely called
on it. Yet, these detect an empty hashtab only by looking at the size.
Fix this by making sure that hashtab_init() always leaves behind a valid
empty hashtab when the allocation fails.
Cc: stable@vger.kernel.org
Fixes: 03414a49ad ("selinux: do not allocate hashtabs dynamically")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83dde7498fefeb920b1def317421262317d178e5 upstream.
Like other commits in the tree add __maybe_unused to a static inline in a
C file because some clang compilers will complain about unused code:
>> drivers/infiniband/core/nldev.c:2543:1: warning: unused function '__chk_RDMA_NL_NLDEV'
MODULE_ALIAS_RDMA_NETLINK(RDMA_NL_NLDEV, 5);
^
Fixes: e3bf14bdc1 ("rdma: Autoload netlink client modules")
Link: https://lore.kernel.org/r/4a8101919b765e01d7fde6f27fd572c958deeb4a.1636267207.git.leonro@nvidia.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4a118f2eead1d6c49e00765de89878288d4b890 upstream.
When __unmap_hugepage_range() calls to huge_pmd_unshare() succeed, a TLB
flush is missing. This TLB flush must be performed before releasing the
i_mmap_rwsem, in order to prevent an unshared PMDs page from being
released and reused before the TLB flush took place.
Arguably, a comprehensive solution would use mmu_gather interface to
batch the TLB flushes and the PMDs page release, however it is not an
easy solution: (1) try_to_unmap_one() and try_to_migrate_one() also call
huge_pmd_unshare() and they cannot use the mmu_gather interface; and (2)
deferring the release of the page reference for the PMDs page until
after i_mmap_rwsem is dropeed can confuse huge_pmd_unshare() into
thinking PMDs are shared when they are not.
Fix __unmap_hugepage_range() by adding the missing TLB flush, and
forcing a flush when unshare is successful.
Fixes: 24669e5847 ("hugetlb: use mmu_gather instead of a temporary linked list for accumulating pages)" # 3.6
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 886fe2915cce6658b0fc19e64b82879325de61ea upstream.
__ufshcd_issue_tm_cmd() clears req->end_io_data after timing out, which
races with the completion function ufshcd_tmc_handler() which expects
req->end_io_data to have a value.
Note __ufshcd_issue_tm_cmd() and ufshcd_tmc_handler() are already
synchronized using hba->tmf_rqs and hba->outstanding_tasks under the
host_lock spinlock.
It is also not necessary (nor typical) to clear req->end_io_data because
the block layer does it before allocating out requests e.g. via
blk_get_request().
So fix by not clearing it.
Link: https://lore.kernel.org/r/20211108064815.569494-2-adrian.hunter@intel.com
Fixes: f5ef336fd2e4 ("scsi: ufs: core: Fix task management completion")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5ef336fd2e4c36dedae4e7ca66cf5349d6fda62 upstream.
The UFS driver uses blk_mq_tagset_busy_iter() when identifying task
management requests to complete, however blk_mq_tagset_busy_iter() doesn't
work.
blk_mq_tagset_busy_iter() only iterates requests dispatched by the block
layer. That appears as if it might have started since commit 37f4a24c24
("blk-mq: centralise related handling into blk_mq_get_driver_tag") which
removed 'data->hctx->tags->rqs[rq->tag] = rq' from blk_mq_rq_ctx_init()
which gets called:
blk_get_request
blk_mq_alloc_request
__blk_mq_alloc_request
blk_mq_rq_ctx_init
Since UFS task management requests are not dispatched by the block layer,
hctx->tags->rqs[rq->tag] remains NULL, and since blk_mq_tagset_busy_iter()
relies on finding requests using hctx->tags->rqs[rq->tag], UFS task
management requests are never found by blk_mq_tagset_busy_iter().
By using blk_mq_tagset_busy_iter(), the UFS driver was relying on internal
details of the block layer, which was fragile and subsequently got
broken. Fix by removing the use of blk_mq_tagset_busy_iter() and having the
driver keep track of task management requests.
Link: https://lore.kernel.org/r/20210922091059.4040-1-adrian.hunter@intel.com
Fixes: 1235fc569e0b ("scsi: ufs: core: Fix task management request completion timeout")
Fixes: 69a6c269c0 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs")
Cc: stable@vger.kernel.org
Tested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf552083916a7f8800477b5986940d1c9a31b953 upstream.
amdgpu_connector_vga_get_modes missed function amdgpu_get_native_mode
which assign amdgpu_encoder->native_mode with *preferred_mode result in
amdgpu_encoder->native_mode.clock always be 0. That will cause
amdgpu_connector_set_property returned early on:
if ((rmx_type != DRM_MODE_SCALE_NONE) &&
(amdgpu_encoder->native_mode.clock == 0))
when we try to set scaling mode Full/Full aspect/Center.
Add the missing function to amdgpu_connector_vga_get_mode can fix this.
It also works on dvi connectors because
amdgpu_connector_dvi_helper_funcs.get_mode use the same method.
Signed-off-by: hongao <hongao@uniontech.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c34bd4532a3f39952952ddc102737595729afc4 upstream.
Atm, there are no sink rate values set for DP (vs. eDP) sinks until the
DPCD capabilities are successfully read from the sink. During this time
intel_dp->num_common_rates is 0 which can lead to a
intel_dp->common_rates[-1] (*)
access, which is an undefined behaviour, in the following cases:
- In intel_dp_sync_state(), if the encoder is enabled without a sink
connected to the encoder's connector (BIOS enabled a monitor, but the
user unplugged the monitor until the driver loaded).
- In intel_dp_sync_state() if the encoder is enabled with a sink
connected, but for some reason the DPCD read has failed.
- In intel_dp_compute_link_config() if modesetting a connector without
a sink connected on it.
- In intel_dp_compute_link_config() if modesetting a connector with a
a sink connected on it, but before probing the connector first.
To avoid the (*) access in all the above cases, make sure that the sink
rate table - and hence the common rate table - is always valid, by
setting a default minimum sink rate when registering the connector
before anything could use it.
I also considered setting all the DP link rates by default, so that
modesetting with higher resolution modes also succeeds in the last two
cases above. However in case a sink is not connected that would stop
working after the first modeset, due to the LT fallback logic. So this
would need more work, beyond the scope of this fix.
As I mentioned in the previous patch, I don't think the issue this patch
fixes is user visible, however it is an undefined behaviour by
definition and triggers a BUG() in CONFIG_UBSAN builds, hence CC:stable.
v2: Clear the default sink rates, before initializing these for eDP.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4297
References: https://gitlab.freedesktop.org/drm/intel/-/issues/4298
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018143417.1452632-1-imre.deak@intel.com
(cherry picked from commit 3f61ef9777c0ab0f03f4af0ed6fd3e5250537a8d)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f55aaf63bde0d0336c3823bb3713bd4a464abbcf upstream.
The postclose handler can run after the device has been removed (or the
driver has been unbound) since userspace clients are free to hold the
file open as long as they want. Because the device removal callback
frees the entire nouveau_drm structure, any reference to it in the
postclose handler will result in a use-after-free.
To reproduce this, one must simply open the device file, unbind the
driver (or physically remove the device), and then close the device
file. This was found and can be reproduced easily with the IGT
core_hotunplug tests.
To avoid this, all clients are cleaned up in the device finalization
rather than deferring it to the postclose handler, and the postclose
handler is protected by a critical section which ensures the
drm_dev_unplug() and the postclose handler won't race.
This is not an ideal fix, since as I understand the proposed plan for
the kernel<->userspace interface for hotplug support, destroying the
client before the file is closed will cause problems. However, I believe
to properly fix this issue, the lifetime of the nouveau_drm structure
needs to be extended to match the drm_device, and this proved to be a
rather invasive change. Thus, I've broken this out so the fix can be
easily backported.
This fixes with the two previous commits CVE-2020-27820 (Karol).
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125202648.5220-4-jcline@redhat.com
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aff2299e0d81b26304ccc6a1ec0170e437f38efc upstream.
Nouveau does not currently support hot-unplugging, but it still makes
sense to switch from drm_dev_unregister() to drm_dev_unplug().
drm_dev_unplug() calls drm_dev_unregister() after marking the device as
unplugged, but only after any device critical sections are finished.
Since nouveau isn't using drm_dev_enter() and drm_dev_exit(), there are
no critical sections so this is nearly functionally equivalent. However,
the DRM layer does check to see if the device is unplugged, and if it is
returns appropriate error codes.
In the future nouveau can add critical sections in order to truly
support hot-unplugging.
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125202648.5220-2-jcline@redhat.com
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abae9164a421bc4a41a3769f01ebcd1f9d955e0e upstream.
Rather than protecting the nouveau_drm clients list with the lock within
the "client" nouveau_cli, add a dedicated lock to serialize access to
the list. This is both clearer and necessary to avoid lockdep being
upset with us when we need to iterate through all the clients in the
list and potentially lock their mutex, which is the same class as the
lock protecting the entire list.
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125202648.5220-3-jcline@redhat.com
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5591c8f79db1729d9c5ac7f5b4d3a5c26e262d93 upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 5320918b9a ("drm/udl: initial UDL driver (v4)")
Cc: stable@vger.kernel.org # 3.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025115353.5089-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 563fbefed46ae4c1f70cffb8eb54c02df480b2c2 upstream.
If the userspace tools switch from NL80211_IFTYPE_P2P_GO to
NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), it
does not call the cleanup cfg80211_stop_ap(), this leads to the
initialization of in-use data. For example, this path re-init the
sdata->assigned_chanctx_list while it is still an element of
assigned_vifs list, and makes that linked list corrupt.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+bbf402b783eeb6d908db@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20211027173722.777287-1-phind.uet@gmail.com
Cc: stable@vger.kernel.org
Fixes: ac800140c2 ("cfg80211: .stop_ap when interface is going down")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bec05f33ebc1006899c6d3e59a00c58881fe7626 upstream.
sticon_build_attr() checked the reverse argument and flipped
background and foreground color, but returned the non-reverse
value afterwards. Fix this and also add two local variables
for foreground and background color to make the code easier
to read.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45da9c1767ac31857df572f0a909fbe88fd5a7e9 upstream.
Ordered work functions aren't guaranteed to be handled by the same thread
which executed the normal work functions. The only way execution between
normal/ordered functions is synchronized is via the WORK_DONE_BIT,
unfortunately the used bitops don't guarantee any ordering whatsoever.
This manifested as seemingly inexplicable crashes on ARM64, where
async_chunk::inode is seen as non-null in async_cow_submit which causes
submit_compressed_extents to be called and crash occurs because
async_chunk::inode suddenly became NULL. The call trace was similar to:
pc : submit_compressed_extents+0x38/0x3d0
lr : async_cow_submit+0x50/0xd0
sp : ffff800015d4bc20
<registers omitted for brevity>
Call trace:
submit_compressed_extents+0x38/0x3d0
async_cow_submit+0x50/0xd0
run_ordered_work+0xc8/0x280
btrfs_work_helper+0x98/0x250
process_one_work+0x1f0/0x4ac
worker_thread+0x188/0x504
kthread+0x110/0x114
ret_from_fork+0x10/0x18
Fix this by adding respective barrier calls which ensure that all
accesses preceding setting of WORK_DONE_BIT are strictly ordered before
setting the flag. At the same time add a read barrier after reading of
WORK_DONE_BIT in run_ordered_work which ensures all subsequent loads
would be strictly ordered after reading the bit. This in turn ensures
are all accesses before WORK_DONE_BIT are going to be strictly ordered
before any access that can occur in ordered_func.
Reported-by: Chris Murphy <lists@colorremedies.com>
Fixes: 08a9ff3264 ("btrfs: Added btrfs_workqueue_struct implemented ordered execution based on kernel workqueue")
CC: stable@vger.kernel.org # 4.4+
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2011928
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Tested-by: Chris Murphy <chris@colorremedies.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9119570039481d56350af1c636f040fb300b8cf3 upstream.
According to upstream commit 5ec55823438e("net: stmmac:
add clocks management for gmac driver"), it improve clocks
management for stmmac driver. So, it is necessary to implement
the runtime callback in dwmac-socfpga driver because it doesn't
use the common stmmac_pltfr_pm_ops instance. Otherwise, clocks
are not disabled when system enters suspend status.
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a48fc69fe6588b48d878d69de223b91a386a7cb4 upstream.
udf_readdir() didn't validate the directory position it should start
reading from. Thus when user uses lseek(2) on directory file descriptor
it can trick udf_readdir() into reading from a position in the middle of
directory entry which then upsets directory parsing code resulting in
errors or even possible kernel crashes. Similarly when the directory is
modified between two readdir calls, the directory position need not be
valid anymore.
Add code to validate current offset in the directory. This is actually
rather expensive for UDF as we need to read from the beginning of the
directory and parse all directory entries. This is because in UDF a
directory is just a stream of data containing directory entries and
since file names are fully under user's control we cannot depend on
detecting magic numbers and checksums in the header of directory entry
as a malicious attacker could fake them. We skip this step if we detect
that nothing changed since the last readdir call.
Reported-by: Nathan Wilson <nate@chickenbrittle.com>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af957eebfcc17433ee83ab85b1195a933ab5049c upstream.
When loading nested state, don't use check vcpu->arch.efer to get the
L1 host's 64-bit vs. 32-bit state and don't check it for consistency
with respect to VM_EXIT_HOST_ADDR_SPACE_SIZE, as register state in vCPU
may be stale when KVM_SET_NESTED_STATE is called---and architecturally
does not exist. When restoring L2 state in KVM, the CPU is placed in
non-root where nested VMX code has no snapshot of L1 host state: VMX
(conditionally) loads host state fields loaded on VM-exit, but they need
not correspond to the state before entry. A simple case occurs in KVM
itself, where the host RIP field points to vmx_vmexit rather than the
instruction following vmlaunch/vmresume.
However, for the particular case of L1 being in 32- or 64-bit mode
on entry, the exit controls can be treated instead as the source of
truth regarding the state of L1 on entry, and can be used to check
that vmcs12.VM_EXIT_HOST_ADDR_SPACE_SIZE matches vmcs12.HOST_EFER if
vmcs12.VM_EXIT_LOAD_IA32_EFER is set. The consistency check on CPU
EFER vs. vmcs12.VM_EXIT_HOST_ADDR_SPACE_SIZE, instead, happens only
on VM-Enter. That's because, again, there's conceptually no "current"
L1 EFER to check on KVM_SET_NESTED_STATE.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20211115131837.195527-2-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 392006871bb26166bcfafa56faf49431c2cfaaa8 upstream.
The SCM changes set the flags in mcp->out_mb instead of mcp->in_mb so the
data was not actually being read into the mcp->mb[] array from the adapter.
Link: https://lore.kernel.org/r/20211108183012.13895-1-emilne@redhat.com
Fixes: 9f2475fe74 ("scsi: qla2xxx: SAN congestion management implementation")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e35eba4055149c578baf0318d2f2f89ea3c44a0 upstream.
As spotted and explained in commit c12ab8dbc492 ("powerpc/8xx: Fix
Oops with STRICT_KERNEL_RWX without DEBUG_RODATA_TEST"), the selection
of STRICT_KERNEL_RWX without selecting DEBUG_RODATA_TEST has spotted
the lack of the DIRTY bit in the pinned kernel data TLBs.
This problem should have been detected a lot earlier if things had
been working as expected. But due to an incredible level of chance or
mishap, this went undetected because of a set of bugs: In fact the
DTLBs were not pinned, because instead of setting the reserve bit
in MD_CTR, it was set in MI_CTR that is the register for ITLBs.
But then, another huge bug was there: the physical address was
reset to 0 at the boundary between RO and RW areas, leading to the
same physical space being mapped at both 0xc0000000 and 0xc8000000.
This had by miracle no consequence until now because the entry was
not really pinned so it was overwritten soon enough to go undetected.
Of course, now that we really pin the DTLBs, it must be fixed as well.
Fixes: f76c8f6d25 ("powerpc/8xx: Add function to set pinned TLBs")
Cc: stable@vger.kernel.org # v5.8+
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Depends-on: c12ab8dbc492 ("powerpc/8xx: Fix Oops with STRICT_KERNEL_RWX without DEBUG_RODATA_TEST")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a21e9a057fe2d247a535aff0d157a54eefee017a.1636963688.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34dbc3aaf5d9e89ba6cc5e24add9458c21ab1950 upstream.
When kmemleak is enabled for SLOB, system does not boot and does not
print anything to the console. At the very early stage in the boot
process we hit infinite recursion from kmemleak_init() and eventually
kernel crashes.
kmemleak_init() specifies SLAB_NOLEAKTRACE for KMEM_CACHE(), but
kmem_cache_create_usercopy() removes it because CACHE_CREATE_MASK is not
valid for SLOB.
Let's fix CACHE_CREATE_MASK and make kmemleak work with SLOB
Link: https://lkml.kernel.org/r/20211115020850.3154366-1-rkovhaev@gmail.com
Fixes: d8843922fb ("slab: Ignore internal flags in cache creation")
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Glauber Costa <glommer@parallels.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 126e8bee943e9926238c891e2df5b5573aee76bc upstream.
Patch series "shm: shm_rmid_forced feature fixes".
Some time ago I met kernel crash after CRIU restore procedure,
fortunately, it was CRIU restore, so, I had dump files and could do
restore many times and crash reproduced easily. After some
investigation I've constructed the minimal reproducer. It was found
that it's use-after-free and it happens only if sysctl
kernel.shm_rmid_forced = 1.
The key of the problem is that the exit_shm() function not handles shp's
object destroy when task->sysvshm.shm_clist contains items from
different IPC namespaces. In most cases this list will contain only
items from one IPC namespace.
How can this list contain object from different namespaces? The
exit_shm() function is designed to clean up this list always when
process leaves IPC namespace. But we made a mistake a long time ago and
did not add a exit_shm() call into the setns() syscall procedures.
The first idea was just to add this call to setns() syscall but it
obviously changes semantics of setns() syscall and that's
userspace-visible change. So, I gave up on this idea.
The first real attempt to address the issue was just to omit forced
destroy if we meet shp object not from current task IPC namespace [1].
But that was not the best idea because task->sysvshm.shm_clist was
protected by rwsem which belongs to current task IPC namespace. It
means that list corruption may occur.
Second approach is just extend exit_shm() to properly handle shp's from
different IPC namespaces [2]. This is really non-trivial thing, I've
put a lot of effort into that but not believed that it's possible to
make it fully safe, clean and clear.
Thanks to the efforts of Manfred Spraul working an elegant solution was
designed. Thanks a lot, Manfred!
Eric also suggested the way to address the issue in ("[RFC][PATCH] shm:
In shm_exit destroy all created and never attached segments") Eric's
idea was to maintain a list of shm_clists one per IPC namespace, use
lock-less lists. But there is some extra memory consumption-related
concerns.
An alternative solution which was suggested by me was implemented in
("shm: reset shm_clist on setns but omit forced shm destroy"). The idea
is pretty simple, we add exit_shm() syscall to setns() but DO NOT
destroy shm segments even if sysctl kernel.shm_rmid_forced = 1, we just
clean up the task->sysvshm.shm_clist list.
This chages semantics of setns() syscall a little bit but in comparision
to the "naive" solution when we just add exit_shm() without any special
exclusions this looks like a safer option.
[1] https://lkml.org/lkml/2021/7/6/1108
[2] https://lkml.org/lkml/2021/7/14/736
This patch (of 2):
Let's produce a warning if we trying to remove non-existing IPC object
from IPC namespace kht/idr structures.
This allows us to catch possible bugs when the ipc_rmid() function was
called with inconsistent struct ipc_ids*, struct kern_ipc_perm*
arguments.
Link: https://lkml.kernel.org/r/20211027224348.611025-1-alexander.mikhalitsyn@virtuozzo.com
Link: https://lkml.kernel.org/r/20211027224348.611025-2-alexander.mikhalitsyn@virtuozzo.com
Co-developed-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f2ec593441d3d1ebc0d478fac3ea329c7c93ac upstream.
When building allmodconfig, there is a warning about TIMER_ENABLE being
redefined:
drivers/clocksource/timer-oxnas-rps.c:39:9: error: 'TIMER_ENABLE' macro redefined [-Werror,-Wmacro-redefined]
#define TIMER_ENABLE BIT(7)
^
arch/hexagon/include/asm/timer-regs.h:13:9: note: previous definition is here
#define TIMER_ENABLE 0
^
1 error generated.
The values in this header are only used in one file each, if they are
used at all. Remove the header and sink all of the constants into their
respective files.
TCX0_CLK_RATE is only used in arch/hexagon/include/asm/timex.h
TIMER_ENABLE, RTOS_TIMER_INT, RTOS_TIMER_REGS_ADDR are only used in
arch/hexagon/kernel/time.c.
SLEEP_CLK_RATE and TIMER_CLR_ON_MATCH have both been unused since the
file's introduction in commit 71e4a47f32 ("Hexagon: Add time and timer
functions").
TIMER_ENABLE is redefined as BIT(0) so the shift is moved into the
definition, rather than its use.
Link: https://lkml.kernel.org/r/20211115174250.1994179-3-nathan@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffb92ce826fd801acb0f4e15b75e4ddf0d189bde upstream.
Patch series "Fixes for ARCH=hexagon allmodconfig", v2.
This series fixes some issues noticed with ARCH=hexagon allmodconfig.
This patch (of 3):
When building ARCH=hexagon allmodconfig, the following errors occur:
ERROR: modpost: "__raw_readsl" [drivers/i3c/master/svc-i3c-master.ko] undefined!
ERROR: modpost: "__raw_writesl" [drivers/i3c/master/dw-i3c-master.ko] undefined!
ERROR: modpost: "__raw_readsl" [drivers/i3c/master/dw-i3c-master.ko] undefined!
ERROR: modpost: "__raw_writesl" [drivers/i3c/master/i3c-master-cdns.ko] undefined!
ERROR: modpost: "__raw_readsl" [drivers/i3c/master/i3c-master-cdns.ko] undefined!
Export these symbols so that modules can use them without any errors.
Link: https://lkml.kernel.org/r/20211115174250.1994179-1-nathan@kernel.org
Link: https://lkml.kernel.org/r/20211115174250.1994179-2-nathan@kernel.org
Fixes: 013bf24c38 ("Hexagon: Provide basic implementation and/or stubs for I/O routines.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a31d27fbed5d518734cb60956303eb15089a7634 upstream.
As stated in the bonding doc, trans_start must be set manually for drivers
using NETIF_F_LLTX:
Drivers that use NETIF_F_LLTX flag must also update
netdev_queue->trans_start. If they do not, then the ARP monitor will
immediately fail any slaves using that driver, and those slaves will stay
down.
Link: https://www.kernel.org/doc/html/v5.15/networking/bonding.html#arp-monitor-operation
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14831fad73f5ac30ac61760487d95a538e6ab3cb upstream.
When running the following command without arm-linux-gnueabi-gcc in
one's $PATH, the following warning is observed:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 mrproper
make[1]: arm-linux-gnueabi-gcc: No such file or directory
This is because KCONFIG is not run for mrproper, so CONFIG_CC_IS_CLANG
is not set, and we end up eagerly evaluating various variables that try
to invoke CC_COMPAT.
This is a similar problem to what was observed in
commit dc960bfeed ("h8300: suppress error messages for 'make clean'")
Reported-by: Lucas Henneman <henneman@google.com>
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211019223646.1146945-4-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec3f415f7244b7747a7952596971adb0df2f568 upstream.
Commit 2d26f6e39afb ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings")
while getting rid of a runtime PM warning ended up breaking ethernet
on rk3399 based devices. By dropping an extra reference to the device,
the commit ends up enabling suspend / resume of the ethernet device -
which appears to be broken.
While the issue with runtime pm is being investigated, partially
revert commit 2d26f6e39afb to restore the network on rk3399.
Fixes: 2d26f6e39afb ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings")
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Cc: Michael Riesch <michael.riesch@wolfvision.net>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210929135049.3426058-1-punitagrawal@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20c76e242e7025bd355619ba67beb243ba1a1e95 ]
kexec_file_add_ipl_report ignores that ipl_report_finish may fail and
can return an error pointer instead of a valid pointer.
Fix this and simplify by returning NULL in case of an error and let
the only caller handle this case.
Fixes: 99feaa717e ("s390/kexec_file: Create ipl report and pass to next kernel")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3866ae319c846a612109c008f43cba80b8c15e86 ]
According to the latest uncore document, COMP_BUF_OCCUPANCY (0xd5) event
can be collected on 2-3 counters. Update uncore IIO event constraints for
Skylake Server.
Fixes: cd34cd97b7 ("perf/x86/intel/uncore: Add Skylake server uncore support")
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20211115090334.3789-3-alexander.antonov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e324234e0aa881b7841c7c713306403e12b069ff ]
According Uncore Reference Manual: any of the CHA events may be filtered
by Thread/Core-ID by using tid modifier in CHA Filter 0 Register.
Update skx_cha_hw_config() to follow Uncore Guide.
Fixes: cd34cd97b7 ("perf/x86/intel/uncore: Add Skylake server uncore support")
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20211115090334.3789-2-alexander.antonov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a3a100473d2f6ebf9bdfe6efedd7e18de724388 ]
It has been observed that dual edge triggered wakeirq GPIOs on SDM845
doesn't trigger interrupts on the falling edge.
Enabling wakeirq_dual_edge_errata for SDM845 indicates that the PDC in
SDM845 suffers from the same problem described, and worked around, by
Doug in 'c3c0c2e18d94 ("pinctrl: qcom: Handle broken/missing PDC dual
edge IRQs on sc7180")', so enable the workaround for SDM845 as well.
The specific problem seen without this is that gpio-keys does not detect
the falling edge of the LID gpio on the Lenovo Yoga C630 and as such
consistently reports the LID as closed.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211102034115.1946036-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dae581864609d36fb58855fd59880b4941ce9d14 ]
kvmppc_h_set_dabr(), and kvmppc_h_set_xdabr() which jumps into
it, need to use _GLOBAL_TOC to setup the kernel TOC pointer, because
kvmppc_h_set_dabr() uses LOAD_REG_ADDR() to load dawr_force_enable.
When called from hcall_try_real_mode() we have the kernel TOC in r2,
established near the start of kvmppc_interrupt_hv(), so there is no
issue.
But they can also be called from kvmppc_pseries_do_hcall() which is
module code, so the access ends up happening with the kvm-hv module's
r2, which will not point at dawr_force_enable and could even cause a
fault.
With the current code layout and compilers we haven't observed a fault
in practice, the load hits somewhere in kvm-hv.ko and silently returns
some bogus value.
Note that we we expect p8/p9 guests to use the DAWR, but SLOF uses
h_set_dabr() to test if sc1 works correctly, see SLOF's
lib/libhvcall/brokensc1.c.
Fixes: c1fe190c06 ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Link: https://lore.kernel.org/r/20210923151031.72408-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d2ca2e12dfb2aff3388ca57b06f570fa6206ced ]
As reported in [1], e100 was no longer working for suspend/resume
cycles. The previous commit mentioned in the fixes appears to have
broken things and this attempts to practice best known methods for
device power management and keep wake-up working while allowing
suspend/resume to work. To do this, I reorder a little bit of code
and fix the resume path to make sure the device is enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=214933
Fixes: 69a74aef8a ("e100: use generic power management")
Cc: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reported-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48b71a9e66c2eab60564b1b1c85f4928ed04e406 ]
There are two sites that calls queue_work() after the
destroy_workqueue() and lead to possible UAF.
The first site is nci_send_cmd(), which can happen after the
nci_close_device as below
nfcmrvl_nci_unregister_dev | nfc_genl_dev_up
nci_close_device |
flush_workqueue |
del_timer_sync |
nci_unregister_device | nfc_get_device
destroy_workqueue | nfc_dev_up
nfc_unregister_device | nci_dev_up
device_del | nci_open_device
| __nci_request
| nci_send_cmd
| queue_work !!!
Another site is nci_cmd_timer, awaked by the nci_cmd_work from the
nci_send_cmd.
... | ...
nci_unregister_device | queue_work
destroy_workqueue |
nfc_unregister_device | ...
device_del | nci_cmd_work
| mod_timer
| ...
| nci_cmd_timer
| queue_work !!!
For the above two UAF, the root cause is that the nfc_dev_up can race
between the nci_unregister_device routine. Therefore, this patch
introduce NCI_UNREG flag to easily eliminate the possible race. In
addition, the mutex_lock in nci_close_device can act as a barrier.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: 6a2968aaf5 ("NFC: basic NCI protocol implementation")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211116152732.19238-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f011539e723c737b74876ac47345e40270a3c384 ]
If there is a NCI command in work queue after closing the NCI device at
nci_unregister_device, The NCI command timer starts at flush_workqueue
function and then NCI command timeout handler would be called 5 second
after flushing the NCI command work queue and destroying the queue.
At that time, the timeout handler would try to use NCI command work queue
that is destroyed already. it will causes the problem. To avoid this
abnormal situation, change the sequence to prevent the NCI command timeout
handler from being called after destroying the NCI command work queue.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e3b5dfcd16a3e254aab61bd1e8c417dd4503102 ]
There is a potential UAF between the unregistration routine and the NFC
netlink operations.
The race that cause that UAF can be shown as below:
(FREE) | (USE)
nfcmrvl_nci_unregister_dev | nfc_genl_dev_up
nci_close_device |
nci_unregister_device | nfc_get_device
nfc_unregister_device | nfc_dev_up
rfkill_destory |
device_del | rfkill_blocked
... | ...
The root cause for this race is concluded below:
1. The rfkill_blocked (USE) in nfc_dev_up is supposed to be placed after
the device_is_registered check.
2. Since the netlink operations are possible just after the device_add
in nfc_register_device, the nfc_dev_up() can happen anywhere during the
rfkill creation process, which leads to data race.
This patch reorder these actions to permit
1. Once device_del is finished, the nfc_dev_up cannot dereference the
rfkill object.
2. The rfkill_register need to be placed after the device_add of nfc_dev
because the parent device need to be created first. So this patch keeps
the order but inject device_lock to prevent the data race.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: be055b2f89 ("NFC: RFKILL support")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211116152652.19217-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86cdf8e38792545161dbe3350a7eced558ba4d15 ]
There is a possible data race as shown below:
thread-A in nci_request() | thread-B in nci_close_device()
| mutex_lock(&ndev->req_lock);
test_bit(NCI_UP, &ndev->flags); |
... | test_and_clear_bit(NCI_UP, &ndev->flags)
mutex_lock(&ndev->req_lock); |
|
This race will allow __nci_request() to be awaked while the device is
getting removed.
Similar to commit e2cb6b891ad2 ("bluetooth: eliminate the potential race
condition when removing the HCI controller"). this patch alters the
function sequence in nci_request() to prevent the data races between the
nci_close_device().
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: 6a2968aaf5 ("NFC: basic NCI protocol implementation")
Link: https://lore.kernel.org/r/20211115145600.8320-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aff430d4e33a0b48a6b3d5beb06f79da23f9916 ]
Fix misleading display error in dmesg if tc filter return fail.
Only i40e status error code should be converted to string, not linux
error code. Otherwise, we return false information about the error.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e6d218c1ec6fb9cd70693b78134cbc35ae0b5a9 ]
Reject TCs creation with proper message if the first queue
assignment is not equal to the power of two.
The first queue number was checked too late in the second queue
iteration, if second queue was configured at all. Now if first queue value
is not a power of two, then trying to create qdisc will be rejected.
Fixes: 8f88b3034d ("i40e: Add infrastructure for queue channel support")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
