As dmaengine_prep_slave_sg() is called with the DMA_CTRL_ACK flag set
for DMA transmit requests, there's no need to explicitly acknowledge DMA
transmit requests in the DMA transmit completion callback.
Hence remove the call to async_tx_ack(), and remove the now unused
dma_async_tx_descriptor pointer in the sci_port structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the SCI driver from the SHDMAE-specific partial DMA transfer
handling to the generic dmaengine residual data framework.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace open-coded
- calls to dma_async_tx_descriptor.tx_submit() by calls to the
dmaengine_submit() helper,
- dma_cookie_t comparisons by calls to dma_submit_error().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mapped transmit buffer is never unmapped. This leaks quite some
mappings, as the mapping is done in uart_ops.startup(), i.e. every time
the device is opened. Unmap the buffer on device close.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the DMA transmit code by using dma_map_single() instead of
constantly modifying the single-entry scatterlist to match what's
currently being transmitted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When comparing differently sized types, it's better to use
min_t()/max_t() than adding casts.
Also use "unsigned int" instead of "int", as that's the right type for
the length of an SG entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To function correctly in the presence of an IOMMU, the DMA buffers must
be managed using the DMA channel's device instead of the platform
device's device.
Make sure to free the DMA memory before releasing the channel, not
after.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let sci_request_dma() handle failures to initialize DMA itself.
This way sci_tx_dma_release() and sci_rx_dma_release() don't have to
consider partial initialization, and thus don't need to reset DMA
addresses to DMA_ERROR_CODE, which is not 100% portable access
architectures.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the life of the driver developer/debugger easier:
- Add __func__ prefix to identical messages,
- Add DMA directions to messages,
- Add TX failure messages,
- Always use "cookie %d" for DMA cookies,
- "#%d" is reserved for the DMA cookie/descriptor index.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix an issue that the driver may cause "nobody cared" IRQ
when this driver detects the overrun flag only.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b6ff84c2d ("serial: sh-sci: Fix R-Car SCIF and HSCIF
overrun handling") added overrun handling for (H)SCIF using the SCLSR
register, but also accidentally added a bogus call to
sci_handle_fifo_overrun() in the receive interrupt path.
Remove it again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reorder sampling_rate assignment for consistency in all cases of the
switch statement.
Avoid using the ternary conditional operator to make it more clear that
the value is overridden by platform data.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_core.c was moved from drivers/serial/ to drivers/tty/serial/ a
while ago. Remove the path to make it move-proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF_ERROR_CLEAR includes SCIFA_ORER, which exists only on SCIFA/SCIFB
and SCIF on sh7705/sh7720/sh7721.
To fix this:
1. Remove SCIFA_ORER from the definition of SCIF_ERROR_CLEAR,
2. During initialization, store the error clear mask to use,
incorporating the overrun bit only if it applies to the SCxSR
register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expressions involving "BIT(...)" create values of type "long", which is
64-bit on 64-bit. Hence "~BIT(...)" no longer fits in 32-bit, which
will cause future compiler warnings when assigning to 32-bit variables:
drivers/tty/serial/sh-sci.c: In function 'sci_init_single':
drivers/tty/serial/sh-sci.h:58:25: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define SCI_ERROR_CLEAR ~(SCI_RESERVED | SCI_PER | SCI_FER | SCI_ORER)
^
drivers/tty/serial/sh-sci.c:2325:27: note: in expansion of macro 'SCI_ERROR_CLEAR'
sci_port->error_clear = SCI_ERROR_CLEAR;
As these values are (at most) 32-bit register values anyway, cast them
to "u32" at the definition level to prevent such compiler warnings.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef logic to clear SCxSR bits using RMW on SCIFA/SCIFB and SCIF
variants with some SCIFA features (sh7705/SH7720/sh7721) has several
drawbacks:
- It wasn't updated for newer R-Mobile variants (APE6),
- It doesn't correctly handle SoCs with both SCIF and SCIFA/B (e.g.
R-Car Gen2, but also legacy sh7723/sh7724),
- It doesn't play well with ARM multi-platform kernels: on R-Car Gen2,
SCIF/SCIFA/SCIFB/HSCIF were handled differently, depending on
whether r8a7740 or sh73a0 support was enabled or not,
Replace the #ifdef logic by runtime logic to fix this.
SCIFA/SCIFB and SCIF on sh7705/sh7720/sh7721 use RMW to clear error
bits, other variants use plain stores, as before.
Note that this changes behavior for SCIFA on sh7723/sh7724 (these SoCs
have both SCIF and SCIFA), which didn't use RMW before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following race conditions can happen when a serial port is used
as console.
Case1: CPU_B is used to detect an interrupt from a serial port,
but it can have interrupts disabled during the waiting time.
Case2: CPU_B clears UART_IER just after CPU_A sets UART_IER and then
a serial port may not make an interrupt.
Case3: CPU_A sets UART_IER just after CPU_B clears UART_IER.
This is an unexpected behavior for serial8250_console_write().
CPU_A [autoconfig_irq] | CPU_B [serial8250_console_write]
----------------------------|---------------------------------------
|
probe_irq_on() | spin_lock_irqsave(&port->lock,)
serial_outp(,UART_IER,0x0f) | serial_out(,UART_IER,0)
udelay(20); | uart_console_write()
probe_irq_off() |
| spin_unlock_irqrestore(&port->lock,)
Case1 and 2 can make autoconfig_irq() failed.
In these cases, the console doesn't work in interrupt mode and
"input overrun" (which can make operation mistakes) can happen
on some systems. Especially in the Case1, It is known that the
problem happens with high rate every boot once it occurs
because the boot sequence is always almost same.
port mutex makes sure that the autoconfig operation is exclusive of
any other concurrent HW access except by the console operation.
console lock is required in autoconfig_irq().
Signed-off-by: Taichi Kageyama <t-kageyama@cp.jp.nec.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes receiving broken characters on the console from an MPC5125
system when systemd comes up which repeatedly opens and shuts down the
console device.
Trial and error with the needed interval showed that 500 us are good
enough most of the time when using 38400 Bd, so I think 1 ms is a good
compromise between fixing the issue and not penalize faster setups too
much.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
8250/Kconfig:config SERIAL_8250_LPC18XX
8250/Kconfig: bool "NXP LPC18xx/43xx serial port support"
...meaning that it currently is not being built as a module by anyone.
When targetting orphaned modular code in non-modular drivers, this
came up. Joachim indicated that the driver was actually meant to
be tristate but ended up bool by accident. So here we make it
tristate instead of removing the modular code that was essentially
orphaned.
Suggested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this driver is currently:
config SERIAL_MPSC
bool "Marvell MPSC serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We leave some tags like MODULE_AUTHOR for documentation purposes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/hvc/Kconfig:config HVC_DRIVER
drivers/tty/hvc/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only, even
though someone bothered to comment that the code was not used.
Unlike other changes, this driver binds in w/o using module_init,
so we dont have init ordering concerns with this commit.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
config.debug:config MAGIC_SYSRQ
bool "Magic SysRq key"
...meaning that it currently is not being built as a module by anyone.
Lets remove the traces of modularity we can so that when reading the
driver there is less doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't delete the module.h include since other parts of the file are
using content from there.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/Kconfig:config LEGACY_PTYS
drivers/tty/Kconfig: bool "Legacy (BSD) PTY support"
...and:
drivers/tty/Kconfig:config UNIX98_PTYS
drivers/tty/Kconfig: bool "Unix98 PTY support" if EXPERT
combined with this:
obj-$(CONFIG_LEGACY_PTYS) += pty.o
obj-$(CONFIG_UNIX98_PTYS) += pty.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the traces of modularity we can so that when reading the
driver there is less doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't delete the module.h include since other parts of the file are
using content from there.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CIR type serial ports aren't real serial ports.
This is just a way to prevent legacy 8250 serial
driver from probing and eventually binding some
resources.
Since in current state such ports aren't providing
any real functionality and it is not possible
to change their type via setserial/ioctl(TIOCSSERIAL)
(due to UPF_FIXED_PORT flag set on them)
it is simpler and cleaner to not register them at all
with serial core.
Print a short message in this case so it is known
to user what has happened.
This way checks for PORT_8250_CIR in serial port
callbacks can be removed too, since they won't
ever be called.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_insert_flip_string() returns an int and as such it
might fail. So the result is that I kindly asked to insert 48 bytes and
the function only insterted 32.
I have no idea what to do with the remaining 16 so I think dropping them
is the only option. I also increase the buf_overrun counter so userpace
has a clue that we lost bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have couple of standard but rare used baudrates which are not supported by
1,8432MHz reference frequency. Besides that user can potentially ask for any
baudrate (via BOTHER flag) and we currently don't fully support that. Since
clk-fractional-divider is moved to use rational best approximation for
reference frequency we may amend the driver to support whatever user wants.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The split of the 8250 driver into a 8250_base/8250.ko resulted in a
lack of a license for the 8250_base.ko module. This caused the module
to fail to load and the kernel to be tainted. Add the appropriate
MODULE_LICENSE to 8250_port.c, which is always compiled into
8250_base.ko
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iucv code uses arrays as arguments. Even though this does not
really cause a problem, it could be misleading, since the compiler
turns array arguments into just a pointer argument. To be more
precise this patch changes the array arguments into pointers.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the correct GFN/BFN terms more consistently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV8VRMAAoJEFxbo/MsZsTRiGQH/i/jrAJUJfrFC2PINaA2gDwe
O0dlrkCiSgAYChGmxxxXZQSPM5Po5+EbT/dLjZ/uvSooeorM9RYY/mFo7ut/qLep
4pyQUuwGtebWGBZTrj9sygUVXVhgJnyoZxskNUbhj9zvP7hb9++IiI78mzne6cpj
lCh/7Z2dgpfRcKlNRu+qpzP79Uc7OqIfDK+IZLrQKlXa7IQDJTQYoRjbKpfCtmMV
BEG3kN9ESx5tLzYiAfxvaxVXl9WQFEoktqe9V8IgOQlVRLgJ2DQWS6vmraGrokWM
3HDOCHtRCXlPhu1Vnrp0R9OgqWbz8FJnmVAndXT8r3Nsjjmd0aLwhJx7YAReO/4=
=JDia
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen terminology fixes from David Vrabel:
"Use the correct GFN/BFN terms more consistently"
* tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: Rename the variable xen_store_mfn to xen_store_gfn
xen/privcmd: Further s/MFN/GFN/ clean-up
hvc/xen: Further s/MFN/GFN clean-up
video/xen-fbfront: Further s/MFN/GFN clean-up
xen/tmem: Use xen_page_to_gfn rather than pfn_to_gfn
xen: Use correctly the Xen memory terminologies
arm/xen: implement correctly pfn_to_mfn
xen: Make clear that swiotlb and biomerge are dealing with DMA address
Here are some reverts for some tty patches (specifically the pl011
driver) that ended up breaking a bunch of machines (i.e. almost all of
the ones with this chip.) People are working on a fix for this, but in
the meantime, it's best to just revert all 5 patches to restore people's
serial consoles.
These reverts have been in linux-next for many days now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlXvtvkACgkQMUfUDdst+ynEVACgvMxKazgRqCnYcqbQs9DwARds
0r4AoL51IVIQe976ZYSjUdSFL+Q0IE1t
=LOn1
-----END PGP SIGNATURE-----
Merge tag 'tty-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty driver reverts from Greg KH:
"Here are some reverts for some tty patches (specifically the pl011
driver) that ended up breaking a bunch of machines (i.e. almost all
of the ones with this chip).
People are working on a fix for this, but in the meantime, it's best
to just revert all 5 patches to restore people's serial consoles.
These reverts have been in linux-next for many days now"
* tag 'tty-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "uart: pl011: Rename regs with enumeration"
Revert "uart: pl011: Introduce register accessor"
Revert "uart: pl011: Introduce register look up table"
Revert "uart: pl011: Improve LCRH register access decision"
Revert "uart: pl011: Add support to ZTE ZX296702 uart"
Merge second patch-bomb from Andrew Morton:
"Almost all of the rest of MM. There was an unusually large amount of
MM material this time"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (141 commits)
zpool: remove no-op module init/exit
mm: zbud: constify the zbud_ops
mm: zpool: constify the zpool_ops
mm: swap: zswap: maybe_preload & refactoring
zram: unify error reporting
zsmalloc: remove null check from destroy_handle_cache()
zsmalloc: do not take class lock in zs_shrinker_count()
zsmalloc: use class->pages_per_zspage
zsmalloc: consider ZS_ALMOST_FULL as migrate source
zsmalloc: partial page ordering within a fullness_list
zsmalloc: use shrinker to trigger auto-compaction
zsmalloc: account the number of compacted pages
zsmalloc/zram: introduce zs_pool_stats api
zsmalloc: cosmetic compaction code adjustments
zsmalloc: introduce zs_can_compact() function
zsmalloc: always keep per-class stats
zsmalloc: drop unused variable `nr_to_migrate'
mm/memblock.c: fix comment in __next_mem_range()
mm/page_alloc.c: fix type information of memoryless node
memory-hotplug: fix comments in zone_spanned_pages_in_node() and zone_spanned_pages_in_node()
...
The force_kill member of struct oom_control isn't needed if an order of -1
is used instead. This is the same as order == -1 in struct
compact_control which requires full memory compaction.
This patch introduces no functional change.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are essential elements to an oom context that are passed around to
multiple functions.
Organize these elements into a new struct, struct oom_control, that
specifies the context for an oom condition.
This patch introduces no functional change.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
HVM_PARAM_CONSOLE_PFN is used to retrieved the console PFN for HVM
guest. It returns a PFN (aka GFN) and not a MFN.
Furthermore, use directly virt_to_gfn for both PV and HVM domain rather
than doing a special case for each of the them.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Based on include/xen/mm.h [1], Linux is mistakenly using MFN when GFN
is meant, I suspect this is because the first support for Xen was for
PV. This resulted in some misimplementation of helpers on ARM and
confused developers about the expected behavior.
For instance, with pfn_to_mfn, we expect to get an MFN based on the name.
Although, if we look at the implementation on x86, it's returning a GFN.
For clarity and avoid new confusion, replace any reference to mfn with
gfn in any helpers used by PV drivers. The x86 code will still keep some
reference of pfn_to_mfn which may be used by all kind of guests
No changes as been made in the hypercall field, even
though they may be invalid, in order to keep the same as the defintion
in xen repo.
Note that page_to_mfn has been renamed to xen_page_to_gfn to avoid a
name to close to the KVM function gfn_to_page.
Take also the opportunity to simplify simple construction such
as pfn_to_mfn(page_to_pfn(page)) into xen_page_to_gfn. More complex clean up
will come in follow-up patches.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=commitdiff;h=e758ed14f390342513405dd766e874934573e6cb
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
This reverts commit 534e14e229 as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7b753f318d as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2c096a9eed as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 09dcc7dfc0 as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8cd90e50d1 as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
- Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- Introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- Use hardware RNG for arch_get_random_seed_* not arch_get_random_* from Paul Mackerras
- Seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh Salgaonkar
- Add powerpc timebase as a trace clock source from Naveen N. Rao
- Misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- Add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- Fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- Drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from Andrew Donnellan
- Initialize distance lookup table from drconf path from Nikunj A Dadhania
- Enable RTC class support from Vaibhav Jain
- Disable automatically blocked PCI config from Gavin Shan
- Add LEDs driver for PowerNV platform from Vasant Hegde
- Fix endianness issues in the HVSI driver from Laurent Dufour
- Kexec endian fixes from Samuel Mendoza-Jonas
- Fix corrupted pdn list from Gavin Shan
- Fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and updates,
device tree updates, e6500 fixes for non-SMP, and misc cleanup and minor
fixes.
- A ton of cxl updates & fixes:
- Add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- Destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- Destroy afu->contexts_idr on release of an afu from Johannes Thumshirn
- Compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- Plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- Add alternate MMIO error handling from Ian Munsie
- Allow release of contexts which have been OPENED but not STARTED from Andrew Donnellan
- Remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- Release irqs if memory allocation fails from Vaibhav Jain
- Remove racy attempt to force EEH invocation in reset from Daniel Axtens
- Fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- Fix force unmapping mmaps of contexts allocated through the kernel api from Ian Munsie
- Set up and enable PSL Timebase from Philippe Bergheaud
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n9+X
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
Weak header file declarations are error-prone because they make every
definition weak, and the linker chooses one based on link order (see
10629d711e ("PCI: Remove __weak annotation from pcibios_get_phb_of_node
decl")).
The most elegant solution is to have a weak default implementation and
allow a strong function to override it. Then we don't have to test
whether a definition is present, and if there are ever multiple strong
definitions, we get a link error instead of calling a random definition.
Add a weak get_c0_fdc_int() definition with the default code and remove the
weak annotation from the declaration.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10687/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes several endianness issues detected when running the HVSI
driver in little endian mode.
These issues are raised in little endian mode because the data exchanged in
memory between the kernel and the hypervisor has to be in big endian
format. This exhibits as errors such as:
irq: (null) didn't like hwirq-0x1000a00 to VIRQ16 mapping (rc=-22)
hvsi_console_init: couldn't create irq mapping for 0x1000a00
The data structures already have endian annotations, and sparse is
generating numerous warnings based on those. This commit fixes all of
them.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: linuxppc-dev@lists.ozlabs.org
CC: linux-kernel@vger.kernel.org
[mpe: Flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This change teaches the imx serial driver to save its
context and restore it across suspend and resume path.
To do so, it introduces serial_imx_restore_context()
and serial_imx_save_context() functions. They use
a shadow set of registers to save key registers
and restore them accordingly. These functions can
be reused on other situations, when the device
context is lost.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets RTSDEN bit when going into idle (Stop mode).
We add the RTSDEN for the case RTS is sent from
the remote connection. This way we allow the system
to wakeup when RTS is received.
Cc: Fabio Stevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change is a code reorganization. Here we introduce
serial_imx_enable_wakeup() helper function to do
the job of configuring and preparing wakeup sources
on imx serial device. The idea is to allow other
parts of the code to call this function whenever
the device is known to go to idle.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code attempts to prepare clk_per and clk_ipg
before using the device. However, the result is an extra
prepare call on each clock. Here is the output of uart
clocks (only uart enabled and used as console):
$ grep uart /sys/kernel/debug/clk/clk_summary
uart_serial 1 2 80000000 0 0
uart 1 2 66000000 0 0
This patch balances the calls of prepares. The result is:
$ grep uart /sys/kernel/debug/clk/clk_summary
uart_serial 1 1 80000000 0 0
uart 1 1 66000000 0 0
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That bitfield is modified by read + or + write operation. If someone
sets any of the other two bits it might render the lock useless.
While at it, remove other bitfields as well to avoid more such
errors.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250-omap driver requires the DMA-engine driver to support the pause
command in order to properly turn off programmed RX transfer before the
driver stars manually reading from the FIFO.
The lacking support of the requirement has been discovered recently. In
order to stay safe here we disable RX-DMA completly on probe.
The rx_dma_broken assignment on probe could be removed once we working
pause function in omap-dma.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the serial core is informed that this device is doing
automatic flow control, it is not necessary to alter CTS and
DCTS of the MSR as the core no longer attempts stop the port
in uart_handle_cts_change().
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
port->lock get's initialized in uart_add_one_port(), no need to do it
in men_z135_probe().
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix panic caused by a race between men_z135_intr() and men_z135_set_termios().
men_z135_intr() and men_z135_set_termios() both hold the struct uart_port::lock
spinlock, but men_z135_intr() does a spin_lock_irqsave() and
men_z135_set_termios() does a normal spin_lock(), which can lead to a deadlock
when an interrupt is called while the lock is being helt by
men_z135_set_termios().
This was discovered using a insmod, hardware looppback send/receive, rmmod
stress test.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: Andreas Werner <andreas.werner@men.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SMSC IrCC SIR/FIR port should not be bound to by
(legacy) serial driver so its own driver (smsc-ircc2)
can bind to it.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently mxs-auart doesn't care correctly about the baud rate divisor.
According to reference manual the baud rate divisor must be between
0x000000EC and 0x003FFFC0. So calculate the possible baud rate range
and use it for uart_get_baud_rate().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever the UART device driver gets closed from userland, the driver
disables the UART unit and then stops the clocks to save power.
The bit which disabled the UART unit is described as:
"UART Enable. If this bit is set to 1, the UART is enabled. Data
transmission and reception occurs for the UART signals. When the
UART is disabled in the middle of transmission or reception, it
completes the current character before stopping."
The important part is the "it completes the current character". Whenever
a reception is ongoing when the UART gets disabled (including the clock
off) the statemachine freezes and "remembers" this state on the next
open() when re-enabling the unit's clock.
In this case we end up receiving an additional bogus character
immediately.
The solution in this change is to switch the AUART unit into its reset
state on close() and only release it from its reset state on the next
open().
Note: when the unit is also used as system console it is always 'in use',
so we cannot reset it on close().
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function clears the reset the AUART unit is in after system start
to make it work.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparation for uniform definition of ioremap, ioremap_wc, ioremap_wt,
and ioremap_cache, tree-wide.
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix RS232/485 mode incorrect setting after S3/S4 resume for F81504/508/512
We had add RS232/485 RTS control with fecf27a373. But when it
resume from S3/S4, the mode register 0x40 + 0x08 * idx + 7 will
rewrite to 0x01 (RS232 mode).
This patch will modify 2 sections.
One is pci_fintek_init(), if it called when first init, it will
write mode register with 0x01. If it called from S3/S4 resume,
it's will get the relative port data and pass it to
pci_fintek_rs485_config() with NULL rs485 parameter.
The another modification is in pci_fintek_rs485_config(). It'll
re-apply old configuration when the parameter rs485 is NULL.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devtype structures are all declared as const.
Compiler does not complain because we cast
their pointers to save them in .driver_data.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently register the uart driver during device probe
which makes it hard to support more than one chip.
Move the driver registration to module init/exit time and
preallocate space for up to 8 lines (4-8 chips).
Reported-by: Michael Allwright <michael.allwright@upb.de>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation of supporting multiple devices we should save
the per-chip line number (0 or 1), because the uart_port line
will reflect system-wide uart number and will be offseted for
chips other than the first to register.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support ZTE uart with some registers differing offset.
Probe as platform device for not AMBA IP ID is
available on ZTE uart.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve LCRH register access decision as ARM PL011 lcrh
register serve as both TX and RX, while other SOC may
implement TX and RX function with separated register.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce register look up table as different SOC venders
may have different register offset for the some register.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce register accessor to ease loop up table access
in later patch.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename regs with enumeration to generalize register names.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pericom PI7C9X795[1248] are Uno/Dual/Quad/Octal UART devices, this
patch enables them, also defines PCI_VENDOR_ID_PERICOM here.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far DMA mode were activated when only number of bytes to send was
equal or greater than min_dma_size. Due to requirement that DMA transaction
buffer should be aligned to cache line size, the excessive bytes were
written to FIFO before starting DMA transaction. The problem occurred
when FIFO size were smaller than cache alignment, because writing all
excessive bytes to FIFO would fail. It happened in DMA mode when PIO
interrupts disabled, which caused driver hung.
The solution is to test if buffer is alligned to cache line size before
activating DMA mode, and if it's not, running PIO mode to align buffer
and then starting DMA transaction. In PIO mode, when interrupts are
enabled, lack of space in FIFO isn't the problem, so buffer aligning
will always finish with success.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to some of serial ports can have FIFO size smaller than cache line
size, and because of need to align DMA buffer address to cache line size,
it's necessary to calculate minimum number of bytes for which we want
to start DMA transaction to be at least cache line size. The simplest
way to meet this requirement is to get maximum of cache line size and
FIFO size.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial core does not use tty_port_open() or tty_port_close(); serial
core defines and extends it's own tty open() and close() methods
(uart_open() and uart_close(), respectively).
Remove the tty_port activate() and shutdown() initializations, and
the uart_port_activate() function, which is never called.
NB: uart_port_shutdown() is used by uart_close() => uart_shutdown()
call chain (but not via the tty_port methods).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_close() runs in non-atomic context only; use
spin_lock/unlock_irq instead of saving the interrupt state (which
== on).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes I/O accesses on the Receiver Holding Register and on the
Transmitter Holding Register. Indeed AVR32 can only perform 32bit I/O
accesses on registers: using 8bit I/O accesses would read or write garbage
data.
Fixes: commit b5199d4681 ("tty/serial: at91: add support to FIFOs")
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.
There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.
This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Documenation/serial/driver requests that the tx_empty callback should
return 0 if there are still chars in the fifo or shifter or TIOCSER_TEMT
(0x01) if no character is pending to be sent.
Fix the mpc52xx serial driver to not return MPC52xx_PSC_SR_TXEMP (i.e.
0x0800) but TIOCSER_TEMT as documented.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implementing enable_ms is optional by serial_core.
check_modem_status is just an empty local function.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When system goes into low power states like SUSPEND_MEM and
HIBERNATION, the hardware IP block may be powered off to reduce
the power consumption. This power down may cause problems on
some imx platforms, because the hardware settings are reset to
its power on default values which may differ from the ones when
it power off. This patch added the dev_pm_ops and implemented
two callbacks: suspend_noirq and resume_noirq, which will save
the necessory hardware parameters right before power down and
recover them before system uses the hardware.
Because added the dev_pm_ops, the old suspend/resume callbacks
under platform_driver will not be called any more. Changed their
prototypes and moved those two callbacks into dev_pm_ops too.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RS485 control for Fintek F81504/508/512
F81504/508/512 can control their RTS with H/W mode.
PCI configuration space for each port is 0x40 + idx * 8 + 7.
When it set with 0x01, it's configured with RS232 mode.
RTS is controlled by MCR.
When it set with 0x11, it's configured with RS485 mode.
RTS is controlled by H/W, RTS low with idle & RX, high with TX.
When it set with 0x31, it's configured with RS485 mode.
RTS is controlled by H/W, RTS high with idle & RX, low with TX.
We will force 0x01 on pci_fintek_setup().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e95044ba4f.
Commit e95044ba4f ("tty: serial: imx.c: Reset UART before activating
interrupts") terribly messes up with the console on mx6 boards, so
let's revert it.
Reported-by: kernelci.org bot <bot@kernelci.org>
Cc: David Jander <david@protonic.nl>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Other serial driver work wants to build on patches now in 4.2-rc4 so
merge the branch so this can properly happen.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Opens of /dev/ptmx don't use tty_open() so debug messages are
not printed for those opens; print a debug message with the
open count (which must always be 1) if TTY_DEBUG_HANGUP is defined.
NB: Each tty core source file undefs support for debug messages.
The relevant source file must be patched/edited to enable these
messages.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add debug messages for ldisc open and close, and remove
"closing ldisc" message from tty_ldisc_release(), because a
close message is now printed for both ldiscs; always print ldisc
pointer first so ldisc changes are easier to identify.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce tty_debug() macro to output uniform debug information for
tty core debug messages (function name and tty name).
Note: printk(KERN_DEBUG) is retained here over pr_debug() since
messages can be enabled in non-DEBUG builds.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Output the function name, tty name, and invariant failure (if applicable).
Add the tty count to the tty_open() message. Fix the disassociate_ctty()
message, which printed the NULL pointer and the wrong message.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this driver is currently:
config SERIAL_SUNHV
bool "Sun4v Hypervisor Console support"
...meaning that it currently is not being built as a module by
anyone. Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't swap module.h for init.h since this file has init.h already.
We leave some tags like MODULE_LICENSE for documentation purposes, and
for the "git blame" value. Also note that MODULE_DEVICE_TABLE is a
no-op for non-modular code, so we remove that too.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this driver is currently:
config SERIAL_SUNCORE
bool
...meaning that it currently is not being built as a module by
anyone. Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't swap module.h for init.h since this file has init.h already.
We leave some tags like MODULE_LICENSE for documentation purposes, and
for the "git blame" value.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this option is currently:
config SERIAL_LANTIQ
bool "Lantiq serial driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We delete the MODULE_DESCRIPTION and LICENSE tags since they are
not adding any new information above and beyond what is at the top
of the file. Also note that MODULE_DEVICE_TABLE is a no-op for
non-modular code, so we remove that as well.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this option is currently:
config SERIAL_SGI_L1_CONSOLE
bool "SGI Altix L1 serial console support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the orphaned module code, so that when reading the
driver there is no doubt it is builtin-only. We could consider
making it tristate, but the above bool has been there since before
the start of git history, which isn't all that surprising, since
consoles are typically critical to have at early boot. So adding
tristate is really of no value here.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 84f57d9e36 ("tty: serial/samsung: fix modular build") fixed
build issues when the driver was built as a module. One of those was
that printascii is only accessible when the driver is built-in.
But there is no need to check for defined(CONFIG_DEBUG_LL) since the
SERIAL_SAMSUNG_DEBUG Kconfig symbol already depends on DEBUG_LL.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The advance of the 'read' buffer index belongs in the outer
flip buffer consume loop, with the other buffer index arithmetic.
No functional change.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clarify flip buffer producer/consumer operation; the use of
smp_load_acquire() and smp_store_release() more clearly indicates
which memory access requires a barrier.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While closing, new rx data may be received after the input buffers
have been flushed but before stop_rx() halts receiving [1]. The
new data might not be processed by flush_to_ldisc() until after
uart_shutdown() and normal input processing is re-enabled (ie.,
tty->closing = 0). The race is outlined below:
CPU 0 | CPU 1
|
uart_close() |
tty_port_close_start() |
tty->closing = 1 |
tty_ldisc_flush() |
| => IRQ
| while (LSR & data ready)
| uart_insert_char()
| tty_flip_buffer_push()
| <= EOI
stop_rx() | .
uart_shutdown() | .
free xmit.buf | .
tty_port_tty_set(NULL) | .
tty->closing = 0 | .
| flush_to_ldisc()
| n_tty_receive_buf_common()
| __receive_buf()
| ...
| commit_echoes()
| uart_flush_chars()
| __uart_start()
| ** OOPS on port.tty deref **
tty_ldisc_flush() |
Input processing must be prevented from echoing (tty->closing = 1)
until _after_ the input buffers have been flushed again at the end
of uart_close().
[1] In fact, some input may actually be buffered _after_ stop_rx()
since the rx interrupt may have already triggered but not yet been
handled when stop_rx() disables rx interrupts.
Fixes: 2e75891083 ("serial: core: Flush ldisc after dropping port
mutex in uart_close()")
Reported-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum bitrate supported depends on the clock rate used in BRG.
This is stored in port.uartclk during probe. Respecting the 16x
oversampling higher bitrates can be supported.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For now this improvement is only used with TX DMA transfers. The data
width must be set properly when configuring the DMA controller. Also
the FIFO configuration must be set to match the DMA transfer data
width:
TXRDYM (Transmitter Ready Mode) and RXRDYM (Receiver Ready Mode) must
be set into the FIFO Mode Register. These values are used by the
USART to trigger the DMA controller. In single data mode they are not
used and should be reset to 0.
So the TXRDYM bits are changed to FOUR_DATA; then USART triggers the
DMA controller when at least 4 data can be written into the TX FIFO
througth the THR. On the other hand the RXRDYM bits are left unchanged
to ONE_DATA.
Atmel eXtended DMA controller allows us to set a different data width
for each part of a scatter-gather transfer. So when calling
dmaengine_slave_config() to configure the TX path, we just need to set
dst_addr_width to the maximum data width. Then DMA writes into THR are
split into up to two parts. The first part carries the first data to
be sent and has a length equal to the greatest multiple of 4 (bytes)
lower than or equal to the total length of the TX DMA transfer. The
second part carries the trailing data (up to 3 bytes). The first part
is written by the DMA into THR using 32 bit accesses, whereas 8bit
accesses are used for the second part.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on the hardware, TX and RX FIFOs may be available. The RX
FIFO can avoid receive overruns, especially when DMA transfers are
not used to read data from the Receive Holding Register. For heavy
system load, The CPU is likely not be able to fetch data fast enough
from the RHR.
In addition, the RX FIFO can supersede the DMA/PDC to control the RTS
line when the Hardware Handshaking mode is enabled. Two thresholds
are to be set for that purpose:
- When the number of data in the RX FIFO crosses and becomes lower
than or equal to the low threshold, the RTS line is set to low
level: the remote peer is requested to send data.
- When the number of data in the RX FIFO crosses and becomes greater
than or equal to the high threshold, the RTS line is set to high
level: the remote peer should stop sending new data.
- low threshold <= high threshold
Once these two thresholds are set properly, this new feature is
enabled by setting the FIFO RTS Control bit of the FIFO Mode Register.
FIFOs also introduce a new multiple data mode: the USART works either
in multiple data mode or in single data (legacy) mode.
If MODE9 bit is set into the Mode Register or if USMODE is set to
either LIN_MASTER, LIN_SLAVE or LON_MODE, FIFOs operate in single
data mode. Otherwise, they operate in multiple data mode.
In this new multiple data mode, accesses to the Receive Holding
Register or Transmit Holding Register slightly change.
Since this driver implements neither the 9bit data feature (MODE9 bit
set into the Mode Register) nor LIN modes, the USART works in
multiple data mode whenever FIFOs are available and enabled. We also
assume that data are 8bit wide.
In single data mode, 32bit access CAN be used to read a single data
from RHR or write a single data into THR.
However in multiple data mode, a 32bit access to RHR now allows us to
read four consecutive data from RX FIFO. Also a 32bit access to THR
now allows to write four consecutive data into TX FIFO. So we MUST
use 8bit access whenever only one data have to be read/written at a
time.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the UART_PUT_*, resp. UART_GET_*, macros by
atmel_uart_writel(), resp. atmel_uart_readl(), inline function calls.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
task_pgrp requires an rcu or tasklist lock to be obtained if the returned pid
is to be dereferenced, which kill_pgrp does. Obtain an RCU lock for the
duration of use.
Signed-off-by: Patrick Donnelly <batrick@batbytes.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XR17V35X UART needs the ECB bit set in its XR_EFR
register to enable access to IER [7:5], ISR [5:4], FCR[5:4],
MCR[7:5], and MSR [7:0].
Also reset the IER register to mask interrupts after access
to all bits of this register has been enabled.
This makes my 8-port XR17V35X working with the in-kernel
serial driver.
Cc: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An already-active sender can swamp the interrupt handler with
"too much work" if the rx interrupts are enabled when the fifo is
disabled and operating in single-byte mode.
Defer rx and line status interrupt enable until after the fifos
are enabled in set_termios(), but at least initialize the shadow
IER value with the interrupts which will be enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ed71871bed ("tty/8250_early: Turn serial_in/serial_out into
weak symbols") made these routines weak to allow platform specific
Big endian override
However recent updates to core, specifically ebc5e20082 ("serial:
of_serial: Support big-endian register accesses") and 6e63be3fee
("serial: earlycon: Add support for big-endian MMIO accesses") means
that round about way to overide the early serial accessors is no longer
needed.
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 068500e08d.
According to some tests, SDMA support is broken at least for i.MX6 without
HW flow control. Different forms of data-corruption appear either with
the ROM firmware for the SDMA controller as well as when loading Freescale
provided SDMA firmware versions 1.1 or 3.1.
Signed-off-by: David Jander <david@protonic.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the UART has been in use before this driver was loaded, IRQs might be
active and get fired as soon as we set the handler, which will crash
in the spin_lock_irqsave(&sport->port.lock, flags) because port.lock is
not initialized until the port is added at the end of probe.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To prevent problems with interrupt latency, and due to the fact, that
the error will be counted anyway (icount.overrun), the dev_err is simply
removed.
Background:
If an rx-fifo overflow occurs a dev_err message was called in interrupt
context. Since dev_err messages are written to console in a synchronous way
(unbuffered), and console may be a serial terminal, this leads to a
highly increased interrupt-latency (several milliseconds).
As a result of the high latency more rx-fifo overflows will happen, and
therefore a feedback loop of errors is created.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Acked-By: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As can be seen in function uart_insert_char (serial_core) the element
buf_overrun of struct uart_icount is used to count overruns of
tty-buffer.
Added support for counting of overruns in imx driver analogue to
serial_core.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable interrupts before requesting them in order to fix a kernel oops
after lauching a kernel via kexec.
Tested on a imx6sl-evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Being a soft core, it can be located not only on PPC or Microblaze
platforms.
Since the driver already does endianness detection we only need to
change the Kconfig to use it in other arches.
This is also done in other softcores as xilinx-spi.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SysRq support activation depends on CONFIG_SERIAL_STM32_USART_CONSOLE, but
this config flag does not exists.
This patch fix this by depending on the valid config flag, which is
SERIAL_STM32_CONSOLE.
Reported-by: Andreas Ruprecht <andreas.ruprecht@fau.de>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calls to regmap_raw_read/write needed register rewrite in a
similar way as function calls to regmap_read/write already had.
This enables reading/writing the serial datastream to the device.
Signed-off-by: Bo Svangård <bo.svangard@embeddedart.se>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I2C=m and SPI=y or-ing them will produce =y while
what we need is the lower bound, i.e. =m. Fortunately
SPI is a boolean so we need to handle only one special
case.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While UART work in DMA mode, function start_rx will request descriptor
from DMA engine, if there is no left descriptor UART, driver will give
err logs "DMA slave single fail".
currently start_rx is called in set_termios function, so everytime, port
setting will call start_rx once.
Now put start_rx in startup, it will be called once while open the port.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when UART works in DMA mode and left bytes in rx fifo less than
a dma transfer unit, DMA engine can't transfer the bytes out
to rx DMA buffer. so it need a way to fetch them out and
flush them into tty buffer in time.
in the above case, we want UART switch from DMA mode to PIO mode and
fetch && flush bytes into tty layer buffer until rxfifo become empty,
after that done let UART switch from PIO mode back to DMA mode.
(record as method1)
method1 result in the next receive result wrong. for example in PIO part
of method1, we fetched && pushed X1...X3 bytes, when UART rxfifo newly
received Y1...Y4 bytes, UART trigger a DMA unit transfer, the DMA unit's
content is X1...X3Y1 and rxfifo fifo status is empty, so X1X2X3 pushed
twice by PIO way and DMA way also the bytes Y2Y3Y4 missed. add rxfifo
reset operation before UART switch back to DMA mode would resolve the
issue. ([method1 + do fifo reset] record as method2)
before the commit, UART driver use method2. but methd2 have a risk of
data loss, as if UART's shift register receive a complete byte and
transfer it into rxfifo before rxfifo reset operation the byte will
loss.
UART and USP have the similar bits CLEAR_RX_ADDR_EN(uart)/FRADDR_CLR_EN(usp),
When found UART controller changing I/O to DMA mode, UART controller
clears the two low bits of read point (rx_fifo_addr[1:0]).
when enable the bit + method1(record as method3), in above example
the DMA unit's content is X1...X3Y1 and there are Y2Y3Y4 in rxfifo by
experiment, we just push bytes in rx DMA buffer.
BTW, the workaround works only for UART receive DMA channel use SINGLE
DMA mode.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In probe, we use dev_id as array index of etraxfs_uart_ports and store the
index in port->line. So etraxfs_uart_ports[port->line] should be released
when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The implementation of cris_console_device() is exactly the same as
uart_console_device(), so let's switch to use uart_console_device().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP h/w-assisted IXON flow control is borked. The transmitter becomes
stuck if XON is never received; clearing the fifos or resetting the
rx flow control bits has no effect.
Remove auto-IXANY as well, since without auto-IXON, it has no purpose.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to Advisory 21 as documented in AM437x errata document,
UART module cannot be disabled once DMA is used. The only
workaround is to softreset the module before disabling it.
DRA7x UARTs are compatible to AM437x UARTs in terms of
this errata and prescribed workaround.
Enable usage of workaround for this errata on DRA7x SoCs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM335x, AM437x and DRA7x SoCs have an errata[1] due to which UART
cannot be idled after it has been used with DMA.
OMAP3 has a similar sounding errata which has been worked around
in a2fc36613a ("ARM: OMAP3: Use manual idle for UARTs
because of DMA errata"). But the workaround used there does not
apply to AM335x, AM437x SoCs.
After using DMA, the UART module on these SoCs must be soft reset
to go to idle.
This patch implements that errata workaround. It is expected that
UART will be used with DMA so no explicit check for DMA usage
has been added for errata applicability.
MDR1 register needs to be restored right after soft-reset because
"UART mode" must be set in that register for module wake-up on AM335x
to work. As a result, SCR register is now used to determine if
context was lost during sleep.
[1] See Advisory 21 in AM437x errata SPRZ408B, updated April 2015.
http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of of_machine_is_compatible() for handling AM335x specific
"DMA kick" quirk in 8250_omap driver makes it ugly to extend the
quirk for other platforms. Instead use a new compatible.
The new compatible will also make it easier to take care of
other quirks on AM335x and like SoCs.
In order to not break backward DTB compatibility for users of
8250_omap driver on AM335x based boards, existing use of
of_machine_is_compatible() has not been removed.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The silicon errata[1] workaround implemented in a follow-on
patch, "serial: 8250_omap: workaround errata on disabling
UART after using DMA", requires MDR1 register programming.
Extract MDR1 register update into helper function,
omap8250_update_mdr1() to help with that.
[1] Advisory 21 in http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_device infrastructure has a suspend_noirq hook which
runtime suspends all devices late in the suspend cycle (see
_od_suspend_noirq() in arch/arm/mach-omap2/omap_device.c)
This leads to a NULL pointer exception in 8250_omap driver
since by the time omap8250_runtime_suspend() is called, 8250_dma
driver has already set rxchan to NULL via serial8250_release_dma().
Make an explicit check to see if rxchan is NULL in
runtime_{suspend|resume} hooks to fix this.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be configured for io addresses different than the standard.
Query the chip for the configured addresses and try to match it with the
pnp address.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chip can be configured to use entry key different than 0x77. Try all the
valid keys until one gives out the right chip id.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some chips with the same interface but different chip ip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be connected at address 0x4e and also 0x2e.
Add some logic to find out the address of the chip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save the port index and the line id in a private structure.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In little endian cases, macro htons unfolds to __swab16 which
provides special case for constants. In big endian cases,
__constant_htons and htons expand directly to the same expression.
So, replace __constant_htons with htons with the goal of getting
rid of the definition of __constant_htons completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_htons(x)
+ htons(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 3873e2d7f6 ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling signalling char, claim the termios write lock before
signalling waiting readers and writers to prevent further i/o
before flushing the echo and output buffers. This prevents a
userspace signal handler which may output from racing the terminal
flush.
Reference: Bugzilla #99351 ("Output truncated in ssh session after...")
Fixes: commit d2b6f44779 ("n_tty: Fix signal handling flushes")
Reported-by: Filipe Brandenburger <filbranden@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVlXl/AAoJEFk3GJrT+8ZlDccQAJ5vxvImNvJmoqeCv+6Tkshm
UOGtoTBWKu+1wVgvYvYWXbNL06NKtS1c/CP8CZE0V6XdLQ+EHd4RWsHyRLHi4xwS
6qqtwVfqYwFLli++87NKqzizl01a0eImPiHl5Rwo9oFy0u81+lsivwWbCBk+Dh0n
HtkmuKzWnKSYL3rgnApq1USL4dhbc6SbNYo0pwvZXNDTK57FrQN/2Z2Pl1FZS9RQ
BQgnqDSdhvF5PD/fWJ5KHs2k2WDtjMMN2TgVMtMjMg2x5kSMAN6fBwi49wYgcwUz
ndHtuHosX4BkPgDHvzIv7jRCYHeRaHOYxbPG+tzYXci4gXUUEn3i8jte91Hb3+ri
tDcgAnod+R1SoBmSRdj/nqM7Y8Qw7Pnjo2tuKYfb1NFaX5KtjrjaaDx/09G7PD+U
fw400HKPi4r2h11n96Y5MZUbLv9XgB9BAePmIdNLuQZabFc1DcsUOG9JbRsMArRT
5g6Sk+Lar9FGH32fLk5sGEAroFs52YmGmLviHKiAsbBSOV751SN2AcA8NDXBuKI1
L+hC41NslENztHTgLsmEt6YY4H/4+jW66du5GYc4ZkPd1scO2+esXDzPZ864vxo+
rIIMnRNQHb2hGiNvImyzEt2NgelSk/xKQR5Dl6MNiKCmiyw2XHlR5UTkRRBZXDd+
5T1KnOvKE2THuxWyWARH
=bhUU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late fixes and dependencies from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable BRCMNAND driver
ARM: BCM: Do not select CONFIG_MTD_NAND_BRCMNAND
ARM: at91/dt: update udc compatible strings
ARM: at91/dt: trivial: fix USB udc compatible string
arm64: dts: Add APM X-Gene standby GPIO controller DTS entries
soc: qcom: spm: Fix idle on THUMB2 kernels
ARM: dove: fix legacy dove IRQ numbers
ARM: mvebu: fix suspend to RAM on big-endian configurations
ARM: mvebu: adjust Armada XP DT spi muxing after pinctrl function rename
serial: 8250_omap: Move wake-up interrupt to generic wakeirq
serial: omap: Switch wake-up interrupt to generic wakeirq
mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0BDx
-----END PGP SIGNATURE-----
Merge tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part one from Paul Gortmaker:
"Replace module_init with equivalent device_initcall in non modules.
This series of commits converts non-modular code that is using the
module_init() call to hook itself into the system to instead use
device_initcall().
The conversion is a runtime no-op, since module_init actually becomes
__initcall in the non-modular case, and that in turn gets mapped onto
device_initcall. A couple files show a larger negative diffstat,
representing ones that had a module_exit function that we remove here
vs previously relying on the linker to dispose of it.
We make this conversion now, so that we can relocate module_init from
init.h into module.h in the future.
The files changed here are just limited to those that would otherwise
have to add module.h to obviously non-modular code, in order to avoid
a compile fail, as testing has shown"
* tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MIPS: don't use module_init in non-modular cobalt/mtd.c file
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
cris: don't use module_init for non-modular core eeprom.c code
tty/metag_da: Avoid module_init/module_exit in non-modular code
drivers/clk: don't use module_init in clk-nomadik.c which is non-modular
xtensa: don't use module_init for non-modular core network.c code
sh: don't use module_init in non-modular psw.c code
mn10300: don't use module_init in non-modular flash.c code
parisc64: don't use module_init for non-modular core perf code
parisc: don't use module_init for non-modular core pdc_cons code
cris: don't use module_init for non-modular core intmem.c code
ia64: don't use module_init in non-modular sim/simscsi.c code
ia64: don't use module_init for non-modular core kernel/mca.c code
arm: don't use module_init in non-modular mach-vexpress/spc.c code
powerpc: don't use module_init in non-modular 83xx suspend code
powerpc: use device_initcall for registering rtc devices
x86: don't use module_init in non-modular devicetree.c code
x86: don't use module_init in non-modular intel_mid_vrtc.c
- Add "make xenconfig" to assist in generating configs for Xen guests.
- Preparatory cleanups necessary for supporting 64 KiB pages in ARM
guests.
- Automatically use hvc0 as the default console in ARM guests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJVkpoqAAoJEFxbo/MsZsTRu3IH/2AMPx2i65hoSqfHtGf3sz/z
XNfcidVmOElFVXGaW83m0tBWMemT5LpOGRfiq5sIo8xt/8xD2vozEkl/3kkf3RrX
EmZDw3E8vmstBdBTjWdovVhNenRc0m0pB5daS7wUdo9cETq1ag1L3BHTB3fEBApO
74V6qAfnhnq+snqWhRD3XAk3LKI0nWuWaV+5HsmxDtnunGhuRLGVs7mwxZGg56sM
mILA0eApGPdwyVVpuDe0SwV52V8E/iuVOWTcomGEN2+cRWffG5+QpHxQA8bOtF6O
KfqldiNXOY/idM+5+oSm9hespmdWbyzsFqmTYz0LvQvxE8eEZtHHB3gIcHkE8QU=
=danz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Xen features and cleanups for 4.2-rc0:
- add "make xenconfig" to assist in generating configs for Xen guests
- preparatory cleanups necessary for supporting 64 KiB pages in ARM
guests
- automatically use hvc0 as the default console in ARM guests"
* tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
block/xen-blkback: s/nr_pages/nr_segs/
block/xen-blkfront: Remove invalid comment
block/xen-blkfront: Remove unused macro MAXIMUM_OUTSTANDING_BLOCK_REQS
arm/xen: Drop duplicate define mfn_to_virt
xen/grant-table: Remove unused macro SPP
xen/xenbus: client: Fix call of virt_to_mfn in xenbus_grant_ring
xen: Include xen/page.h rather than asm/xen/page.h
kconfig: add xenconfig defconfig helper
kconfig: clarify kvmconfig is for kvm
xen/pcifront: Remove usage of struct timeval
xen/tmem: use BUILD_BUG_ON() in favor of BUG_ON()
hvc_xen: avoid uninitialized variable warning
xenbus: avoid uninitialized variable warning
xen/arm: allow console=hvc0 to be omitted for guests
arm,arm64/xen: move Xen initialization earlier
arm/xen: Correctly check if the event channel interrupt is present
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVkgKHAAoJENkgDmzRrbjxQpwQAJVmBN6jF3SnwbQXv9vRixjH
58V33sb1G1RW+kXxQ3/e8jLX/4VaN479CufruXQp+IJWXsN/CH0lbC3k8m7u50d7
b1Zeqd/Yrh79rkc11b0X1698uGCSMlzz+V54Z0QOTEEX+nSu2ZZvccFS4UaHkn3z
rqDo00lb7rxQz8U25qro2OZrG6D3ub2q20TkWUB8EO4AOHkPn8KWP2r429Axrr0K
wlDWDTTt8/IsvPbuPf3T15RAhq1avkMXWn9nDXDjyWbpLfTn8NFnWmtesgY7Jl4t
GjbXC5WYekX3w2ZDB9KaT/DAMQ1a7RbMXNSz4RX4VbzDl+yYeSLmIh2G9fZb1PbB
PsIxrOgy4BquOWsJPm+zeFPSC3q9Cfu219L4AmxSjiZxC3dlosg5rIB892Mjoyv4
qxmg6oiqtc4Jxv+Gl9lRFVOqyHZrTC5IJ+xgfv1EyP6kKMUKLlDZtxZAuQxpUyxR
HZLq220RYnYSvkWauikq4M8fqFM8bdt6hLJnv7bVqllseROk9stCvjSiE3A9szH5
OgtOfYV5GhOeb8pCZqJKlGDw+RoJ21jtNCgOr6DgkNKV9CX/kL/Puwv8gnA0B0eh
dxCeB7f/gcLl7Cg3Z3gVVcGlgak6JWrLf5ITAJhBZ8Lv+AtL2DKmwEWS/iIMRmek
tLdh/a9GiCitqS0bT7GE
=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Pull arch/tile updates from Chris Metcalf:
"These are a grab bag of changes to improve debugging and respond to a
variety of issues raised on LKML over the last couple of months"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: avoid a "label not used" warning in do_page_fault()
tile: vdso: use raw_read_seqcount_begin() in vdso
tile: force CONFIG_TILEGX if ARCH != tilepro
tile: improve stack backtrace
tile: fix "odd fault" warning for stack backtraces
tile: set up initial stack top to honor STACK_TOP_DELTA
tile: support delivering NMIs for multicore backtrace
drivers/tty/hvc/hvc_tile.c: properly return -EAGAIN
tile: add <asm/word-at-a-time.h> and enable support functions
tile: use READ_ONCE() in arch_spin_is_locked()
tile: modify arch_spin_unlock_wait() semantics
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoSAACgkQMUfUDdst+ymxNQCguSEmkAYNDdLyYhdcOqSxJt9u
U1gAoMThUDoomkx6CTDMU1wn53hxgMk9
=eCUS
-----END PGP SIGNATURE-----
Merge tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
Here's the big, really big, staging tree patches for 4.2-rc1.
Loads of stuff in here, almost all just coding style fixes / churn, and
a few new drivers as well, one of which I just disabled from the build a
few minutes ago due to way too many build warnings.
Other than the one "disable this driver" patch, all of these have been
in linux-next for quite a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNpc0ACgkQMUfUDdst+ym8EgCg0pL1Qcf9Se3jAc96fLt+itpv
Rd0AoI9uJcq8Qm7d+IXnz3ojLnN9xvN3
=xt0u
-----END PGP SIGNATURE-----
Merge tag 'staging-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big, really big, staging tree patches for 4.2-rc1.
Loads of stuff in here, almost all just coding style fixes / churn,
and a few new drivers as well, one of which I just disabled from the
build a few minutes ago due to way too many build warnings.
Other than the one "disable this driver" patch, all of these have been
in linux-next for quite a while with no reported issues"
* tag 'staging-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1163 commits)
staging: wilc1000: disable driver due to build warnings
Staging: rts5208: fix CHANGE_LINK_STATE value
Staging: sm750fb: ddk750_swi2c.c: Insert spaces before parenthesis
Staging: sm750fb: ddk750_swi2c.c: Place braces on correct lines
Staging: sm750fb: ddk750_swi2c.c: Insert spaces around operators
Staging: sm750fb: ddk750_swi2c.c: Replace spaces with tabs
Staging: sm750fb: ddk750_swi2c.h: Shorten lines to under 80 characters
Staging: sm750fb: ddk750_swi2c.h: Replace spaces with tabs
Staging: sm750fb: modedb.h: Shorten lines to under 80 characters
Staging: sm750fb: modedb.h: Replace spaces with tabs
staging: comedi: addi_apci_3120: rename 'this_board' variables
staging: comedi: addi_apci_1516: rename 'this_board' variables
staging: comedi: ni_atmio: cleanup ni_getboardtype()
staging: comedi: vmk80xx: sanity check context used to get the boardinfo
staging: comedi: vmk80xx: rename 'boardinfo' variables
staging: comedi: dt3000: rename 'this_board' variables
staging: comedi: adv_pci_dio: rename 'this_board' variables
staging: comedi: cb_pcidas64: rename 'thisboard' variables
staging: comedi: cb_pcidas: rename 'thisboard' variables
staging: comedi: me4000: rename 'thisboard' variables
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fE8E
-----END PGP SIGNATURE-----
Merge tag 'for-4.2' of git://git.sourceforge.jp/gitroot/uclinux-h8/linux
Pull Renesas H8/300 architecture re-introduction from Yoshinori Sato.
We dropped arch/h8300 two years ago as stale and old, this is a new and
more modern rewritten arch support for the same architecture.
* tag 'for-4.2' of git://git.sourceforge.jp/gitroot/uclinux-h8/linux: (27 commits)
h8300: fix typo.
h8300: Always build dtb
h8300: Remove ARCH_WANT_IPC_PARSE_VERSION
sh-sci: Get register size from platform device
clk: h8300: fix error handling in h8s2678_pll_clk_setup()
h8300: Symbol name fix
h8300: devicetree source
h8300: configs
h8300: IRQ chip driver
h8300: clocksource
h8300: clock driver
h8300: Build scripts
h8300: library functions
h8300: Memory management
h8300: miscellaneous functions
h8300: process helpers
h8300: compressed image support
h8300: Low level entry
h8300: kernel startup
h8300: Interrupt and exceptions
...
Merge first patchbomb from Andrew Morton:
- a few misc things
- ocfs2 udpates
- kernel/watchdog.c feature work (took ages to get right)
- most of MM. A few tricky bits are held up and probably won't make 4.2.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (91 commits)
mm: kmemleak_alloc_percpu() should follow the gfp from per_alloc()
mm, thp: respect MPOL_PREFERRED policy with non-local node
tmpfs: truncate prealloc blocks past i_size
mm/memory hotplug: print the last vmemmap region at the end of hot add memory
mm/mmap.c: optimization of do_mmap_pgoff function
mm: kmemleak: optimise kmemleak_lock acquiring during kmemleak_scan
mm: kmemleak: avoid deadlock on the kmemleak object insertion error path
mm: kmemleak: do not acquire scan_mutex in kmemleak_do_cleanup()
mm: kmemleak: fix delete_object_*() race when called on the same memory block
mm: kmemleak: allow safe memory scanning during kmemleak disabling
memcg: convert mem_cgroup->under_oom from atomic_t to int
memcg: remove unused mem_cgroup->oom_wakeups
frontswap: allow multiple backends
x86, mirror: x86 enabling - find mirrored memory ranges
mm/memblock: allocate boot time data structures from mirrored memory
mm/memblock: add extra "flags" to memblock to allow selection of memory based on attribute
mm: do not ignore mapping_gfp_mask in page cache allocation paths
mm/cma.c: fix typos in comments
mm/oom_kill.c: print points as unsigned int
mm/hugetlb: handle races in alloc_huge_page and hugetlb_reserve_pages
...
Pull input subsystem updates from Dmitry Torokhov:
"Thanks to Samuel Thibault input device (keyboard) LEDs are no longer
hardwired within the input core but use LED subsystem and so allow use
of different triggers; Hans de Goede did a large update for the ALPS
touchpad driver; we have new TI drv2665 haptics driver and DA9063
OnKey driver, and host of other drivers got various fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: pixcir_i2c_ts - fix receive error
MAINTAINERS: remove non existent input mt git tree
Input: improve usage of gpiod API
tty/vt/keyboard: define LED triggers for VT keyboard lock states
tty/vt/keyboard: define LED triggers for VT LED states
Input: export LEDs as class devices in sysfs
Input: cyttsp4 - use swap() in cyttsp4_get_touch()
Input: goodix - do not explicitly set evbits in input device
Input: goodix - export id and version read from device
Input: goodix - fix variable length array warning
Input: goodix - fix alignment issues
Input: add OnKey driver for DA9063 MFD part
Input: elan_i2c - add product IDs FW names
Input: elan_i2c - add support for multi IC type and iap format
Input: focaltech - report finger width to userspace
tty: remove platform_sysrq_reset_seq
Input: synaptics_i2c - use proper boolean values
Input: psmouse - use true instead of 1 for boolean values
Input: cyapa - fix a few typos in comments
Input: stmpe-ts - enforce device tree only mode
...
The zonelist locking and the oom_sem are two overlapping locks that are
used to serialize global OOM killing against different things.
The historical zonelist locking serializes OOM kills from allocations with
overlapping zonelists against each other to prevent killing more tasks
than necessary in the same memory domain. Only when neither tasklists nor
zonelists from two concurrent OOM kills overlap (tasks in separate memcgs
bound to separate nodes) are OOM kills allowed to execute in parallel.
The younger oom_sem is a read-write lock to serialize OOM killing against
the PM code trying to disable the OOM killer altogether.
However, the OOM killer is a fairly cold error path, there is really no
reason to optimize for highly performant and concurrent OOM kills. And
the oom_sem is just flat-out redundant.
Replace both locking schemes with a single global mutex serializing OOM
kills regardless of context.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Disable the 32-bit vdso when building LE, so we can build with a 64-bit only
toolchain.
- EEH fixes from Gavin & Richard.
- Enable the sys_kcmp syscall from Laurent.
- Sysfs control for fastsleep workaround from Shreyas.
- Expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- Fix for kernel to userspace backtraces for perf from Anton.
- Merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- Fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- Dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- Reworked version of the patch to abort syscalls when transactional.
- Fix the swap encoding to support 4TB, from Aneesh.
- Various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx optimizations, an
e6500 hugetlb optimization, QMan device tree nodes, t1024/t1023 support, and
various fixes and cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=d9Wh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
kernel series:
- A big set of cleanups to the aged sysfs interface from
Johan Hovold. To get these in, v4.1-rc3 was merged into
the tree as the first patch in that series had to go
into stable. This makes the locking much more fine-grained
(get rid of the "big GPIO lock(s)" and store states in the
GPIO descriptors.
- Rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value()
to avoid confusions.
- New drivers for:
- NXP LPC18xx (currently LPC1850)
- NetLogic XLP
- Broadcom STB SoC's
- Axis ETRAXFS
- Zynq Ultrascale+ (subdriver)
- ACPI:
- Make it possible to retrieve GpioInt resources from
a GPIO device using acpi_dev_gpio_irq_get()
- Merge some dependent I2C changes exploiting this.
- Support the ARM X-Gene GPIO standby driver.
- Make it possible for the generic GPIO driver to read
back the value set registers to reflect current
status.
- Loads of OMAP IRQ handling fixes.
- Incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- Janitorial (contification, checkpatch cleanups)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vKYs
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the big bulk of GPIO changes queued for the v4.2 kernel
series:
- a big set of cleanups to the aged sysfs interface from Johan
Hovold. To get these in, v4.1-rc3 was merged into the tree as the
first patch in that series had to go into stable. This makes the
locking much more fine-grained (get rid of the "big GPIO lock(s)"
and store states in the GPIO descriptors.
- rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
avoid confusions.
- New drivers for:
* NXP LPC18xx (currently LPC1850)
* NetLogic XLP
* Broadcom STB SoC's
* Axis ETRAXFS
* Zynq Ultrascale+ (subdriver)
- ACPI:
* make it possible to retrieve GpioInt resources from a GPIO
device using acpi_dev_gpio_irq_get()
* merge some dependent I2C changes exploiting this.
* support the ARM X-Gene GPIO standby driver.
- make it possible for the generic GPIO driver to read back the value
set registers to reflect current status.
- loads of OMAP IRQ handling fixes.
- incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- janitorial (constification, checkpatch cleanups)"
* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: Fix checkpatch.pl issues
gpio: pcf857x: handle only enabled irqs
gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
gpio: improve error reporting on own descriptors
gpio: promote own request failure to pr_err()
gpio: Added support to Zynq Ultrascale+ MPSoC
gpio: add ETRAXFS GPIO driver
fix documentation after renaming gpiod_set_array to gpiod_set_array_value
gpio: Add GPIO support for Broadcom STB SoCs
gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
gpio: tb10x: Drop unneeded free_irq() call
gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
gpio: stp-xway: Use the of_property_read_u32 helper
gpio: pcf857x: Check for irq_set_irq_wake() failures
gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
gpio: Prevent an integer overflow in the pca953x driver
gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
gpio: omap: rework omap_gpio_request to touch only gpio specific registers
gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
...
There is much SCI of SoC having within,
and the register size is also different in everyone.
So get from platform device.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Acked-by: by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Introduce a driver suitable for use with the UARTs present in
Ingenic SoCs such as the JZ4740 & JZ4780. These are described as being
ns16550 compatible but aren't quite - they require the setting of an
extra bit in the FCR register to enable the UART module. The serial_out
implementation is the same as that in arch/mips/jz4740/serial.c - which
will shortly be removed.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-serial@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/10159/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a MIPS specific SysRq operation to dump the TLB entries on all CPUs,
using the 'x' trigger key.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10072/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In addition to defining triggers for VT LED states, let's define triggers
for VT keyboard lock states, such as "kbd-shiftlock", "kbd-altgrlock", etc.
This permits to fix#7063 from userland by using a modifier to implement
proper CapsLock behavior and have the keyboard caps lock led show that
modifier state.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that input core allows controlling keyboards LEDs via standard LED
subsystem triggers let's switch VT keyboard code to make use of this
feature. We will define the following standard triggers: "kbd-scrollock",
"kbd-numlock", "kbd-capslock", and "kbd-kanalock" which are default
triggers for respective LEDs on keyboards.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The metag_da TTY driver can't get built as a module at the moment, but
it still uses module_init() and module_exit(). Those macros are moving
to module.h which isn't included by metag_da.c, which will result in the
following build warnings (remarkably no build errors) and an apparent
failure to boot as the TTY driver won't be loaded.
drivers/tty/metag_da.c:660: warning: data definition has no type or storage class
drivers/tty/metag_da.c:660: warning: type defaults to ‘int’ in declaration of ‘module_init’
drivers/tty/metag_da.c:660: warning: parameter names (without types) in function declaration
drivers/tty/metag_da.c:661: warning: data definition has no type or storage class
drivers/tty/metag_da.c:661: warning: type defaults to ‘int’ in declaration of ‘module_exit’
drivers/tty/metag_da.c:661: warning: parameter names (without types) in function declaration
drivers/tty/metag_da.c:572: warning: ‘dashtty_init’ defined but not used
drivers/tty/metag_da.c:645: warning: ‘dashtty_exit’ defined but not used
drivers/tty/metag_da.c In function ‘dash_console_write’:
drivers/tty/metag_da.c:670 : warning: passing argument 4 of ‘chancall’ discards qualifiers from pointer target type
Instead of just adding the module.h include, now would be a good time to
remove the use of these macros, replacing the module_init with
device_initcall, and removing the exit function altogether since it
isn't needed. If module support is added later the code can always be
resurrected.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-metag@vger.kernel.org
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In platforms which does not use CLK framework (HAVE_CLK not set), the
clk_* functions return NULL instead of an error. This patch handles that
scenario.
Signed-off-by: Fernando Guzman Lugo <fernando.guzman.lugo@intel.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The internal clock of the master chip, which is usually 125MHz, is only half
(62.5MHz) for the slave chips. So we have to adjust the uartclk for all the
slave ports. Therefor we add a new function to determine if a slave chip is
present and update pci_xr17v35x_setup accordingly.
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exar XR17V358 can also be combined with a XR17V354 chip to act as a
single 12 port chip. This works the same way as the combining two XR17V358
chips. But the reported device id then is 0x4358.
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align with coding guidelines:
Replaced a chain of "else if" by a switch case.
Signed-off-by: Joakim Nordell <joakim.nordell@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This drivers adds support to the STM32 USART controller, which is a
standard serial driver.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now use generic wakeirq handling and remove the custom handling
for the wake-up interrupts.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now use generic wakeirq handling and remove the custom handling
for the wake-up interrupts.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also set IRQ_NOPROBE and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few TTY and Serial driver fixes for reported regressions and
crashes. All of these have been in linux-next with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlVzhBsACgkQMUfUDdst+yk3vACgok97fBbPTarm5Xw7yZAbu3tD
6twAmwQC2GwyyAoZz3HTjK0NQnfBIm8N
=j8nR
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a few TTY and Serial driver fixes for reported regressions
and crashes.
All of these have been in linux-next with no reported problems"
* tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
n_tty: Fix auditing support for cannonical mode
serial: 8250_omap: provide complete custom startup & shutdown callbacks
n_tty: Fix calculation of size in canon_copy_from_read_buf
serial: imx: Fix DMA handling for IDLE condition aborts
serial/amba-pl011: Unconditionally poll for FIFO space before each TX char
The platform_sysrq_reset_seq code was intended as a way for an embedded
platform to provide its own sysrq sequence at compile time. After over two
years, nobody has started using it in an upstream kernel, and the platforms
that were interested in it have moved on to devicetree, which can be used
to configure the sequence without requiring kernel changes. The method is
also incompatible with the way that most architectures build support for
multiple platforms into a single kernel.
Now the code is producing warnings when built with gcc-5.1:
drivers/tty/sysrq.c: In function 'sysrq_init':
drivers/tty/sysrq.c:959:33: warning: array subscript is above array bounds [-Warray-bounds]
key = platform_sysrq_reset_seq[i];
We could fix this, but it seems unlikely that it will ever be used, so
let's just remove the code instead. We still have the option to pass the
sequence either in DT, using the kernel command line, or using the
/sys/module/sysrq/parameters/reset_seq file.
Fixes: 154b7a489a ("Input: sysrq - allow specifying alternate reset sequence")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 32f13521ca
("n_tty: Line copy to user buffer in canonical mode")
changed cannonical mode copying to use copy_to_user
but missed adding the call to the audit framework.
Add in the appropriate functions to get audit support.
Fixes: 32f13521ca ("n_tty: Line copy to user buffer in canonical mode")
Reported-by: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d118 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").
This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.
Fixes: ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core:
read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial port driver for the 8250-based UART found on LPC18xx/43xx
devices. The UART is 16550A compatible with additional features
like RS485 support, synchronous mode, IrDA, and DMA.
For now only basic UART and RS485 operation is supported.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the driver for on-chip UART used on UniPhier SoCs.
This hardware is similar to 8250, but the register mapping is
slightly different:
- The offset to FCR, MCR is different.
- The divisor latch access bit does not exist. Instead, the
divisor latch register is available at offset 9.
This driver overrides serial_{in,out}, dl_{read,write} callbacks,
but wants to borrow most of code from 8250_core.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On many new Intel SoCs the UART has an integrated DMA engine
(iDMA). In order to use it a special filter function is needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function clk_prepare_enable() may fail, and in that case it
does not make sense to proceed. Let's check its return code and
error out if it is a negative value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe method of this driver calls clk_get(), but clk_put() is
missing from the remove callback.
Using the managed clk function is easier than fixing other parts.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support command line parameters of the form:
earlycon=<name>,io|mmio|mmio32|mmio32be,<addr>,<options>
This commit seem to be needed even after commit:
serial: 8250: Add support for big-endian MMIO accesses
c627f2ceb6
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when the serial works as a bluetooth sink, due to audio realtime
requirement, the driver should have something similar with ALSA:
1. one big DMA buffer to easy the schedule jitter
2. split this big DMA buffer to multiple small periods, for each
period, we get a DMA interrupt, then push the data to userspace.
the small periods will easy the audio latency.
so ALSA generally uses a cyclic chained DMA.
but for sirfsoc, the dma hardware has the limitation: we have
only two loops in the cyclic mode, so we can only support two
small periods to switch. if we make the DMA buffer too big, we
get long latency, if we make the DMA buffer too little, we get
miss in scheduling for audio realtime.
so this patch moves to use a hrtimer to simulate the cyclic
DMA, then we can have a big buffer, and also have a timely
data push to users as the hrtimer can generate in small period
then actual HW interrupts.
with this patch, we also delete a lot of complex codes to handle
loop buffers, and RX timeout interrupt since the RX work can be
completely handled from hrtimer interrupt.
tests show using this way will make our bad audio streaming be-
come smooth.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A corner case exists in the current driver. if an app opens the console
device, and before writing to console device, and there are huge kernel
ogs to print out, system will hang on
sirfsoc_uart_console_putchar:
while (rd_regl(port, ureg->sirfsoc_tx_fifo_status) &
ufifo_st->ff_full(port->line))
cpu_relax();
as in sirfsoc_uart_startup(), the driver assigns tx_fifo_op to 0 will stop
TX FIFO, this loop will be endless.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_set_mctrl() is a void type function. Returning something
does not look nice.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS-485 configuration is also done under the spinlock
so no blocking I/O allowed.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
.stop_rx/tx() are called in atomic context, we cannot use
blocking I/O. While at it correct the name of RX bit and
'*' placement in pointer declarations.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert md_proc into general async reconfiguration procedure.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of spinning under port->lock let's just sleep
inside the kthread. It should be equivalent as TX cannot
proceed when thread is blocked.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert workqueue usage to a real-time kworker. The problem
with workqueues is that we cannot set real-time priorities on
our work and asynchronous reconfiguration can be blocked by
less important tasks.
We need kthread for the interrupt anyway and because we will
now be using single kthread for all TX-related operations we
can get rid of the port mutex.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
