Jffs2 apparently needs this.
Accept newline at the end of input.
Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Remove Gareth from the Copyrights (at his own request)
- Fix the "fscking embarrassment"
Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove support for the Arcom Elan-104NC since it's no longer being maintained.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace msleep by cond_resched. On machines with HZ=100 (e.g. ARM)
msleep slows down the operation by factor 10
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix fairly sad NOR-specific bug - during FS building ic->scan_dents
isn't zero, but jffs2_mark_node_obsolete() migt be called it tries to
finde the ic corresponding to ref - this requires ic->scan_dents = 0.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Don't remove inocache for inodes which are in read_inode() or
clear_inode() until they're done.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This driver does not have as many options but it's easier to maintain.
And, it turns out AMD never shipped boards with different flash densities.
Signed-off-by: Pete Popov <ppopov@pacbell.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexander Nyberg <alexn@dsv.su.se>
Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Check timeout while we wait for the command to finish. No worry about a
false result. This prevents deadlocking when detecting an unknown number
of chips and is useful for removable media too.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Do not use the ready function here, as it might hang for ever.
The result will show, whether the chip is there or not
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix sparse errors due to lack of address-space markers
Updated header comments
Small re-format of initialiser
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
update the BAST driver config (which already supports the vr1000) to
be selected only if the vr1000 has been configured
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Look the ref->next_phys field instead of ->next_in_ino to determine
if the block has more then one node.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Scan 1st and 2nd pages of SP devices for BB marker by default.
Fix more then one page scanning in create_bbt.c.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move manufacturer ID search to display correct ID in case of buswidth
mismatch.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The change to the generic probe to look for the
smallest width of chip first is causing some problems
on boards with a single 16bit device.
The problem seems to be the jedec_match() is truncating
the device-id read from the table to match against the
one read from the hardware, causing a match against the
partial id of some chips with 16bit IDs (such as the
SST39LF160)
This fixes things for my own board, but something may
need to be done if the same problem is exhibited for
chips with an 8bit ID
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When scanning NAND for bad blocks, don't read the whole page, read
only needed OOB bytes instead. Also check the return code of the
nand_read_raw() function. Correctly free the this->bbt array in
case of failure. Tested with Large page NAND.
Fix debugging message.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Small bugfix. Sometimes it may be handy not to have bbt.
So, this->bbt might be NULL.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch replaces the current CONFIG_JFFS2_FS_NAND, CONFIG_JFFS2_FS_NOR_ECC
and CONFIG_JFFS2_FS_DATAFLASH with a single configuration option -
CONFIG_JFFS2_FS_WRITEBUFFER.
The only functional change of this patch is that the slower div/mod
calculations for SECTOR_ADDR(), PAGE_DIV() and PAGE_MOD() are now always
used when CONFIG_JFFS2_FS_WRITEBUFFER is enabled.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For Dataflash, can_mark_obsolete = false and the NAND write buffering
code (wbuf.c) is used.
Since the DataFlash chip will automatically erase pages when writing,
the cleanmarkers are not needed - so cleanmarker_oob = false and
cleanmarker_size = 0
DataFlash page-sizes are not a power of two (they're multiples of 528
bytes). The SECTOR_ADDR macro (added in the previous core patch) is
replaced with a (slower) div/mod version if CONFIG_JFFS2_FS_DATAFLASH is
selected.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
DataFlash page-sizes are not a power of two (they're multiples of 528
bytes). There are a few places in JFFS2 code where sector_size is used
as a bitmask. A new macro (SECTOR_ADDR) was defined to calculate these
sector addresses. For non-DataFlash devices, the original (faster)
bitmask operation is still used.
In scan.c, the EMPTY_SCAN_SIZE was a constant of 1024.
Since this could be larger than the sector size of the DataFlash, this
is now basically set to MIN(sector_size, 1024).
Addition of a jffs2_is_writebuffered() macro.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is implemented using a ioctl to switch the MTD char device into
one of the different OTP "modes", at which point read/write/seek can
operate on the selected OTP area. Also some extra ioctls to query
for size and lock protection segments or groups. Some example user
space utilities are provided.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This enables support for reading, writing and locking so called
"Protection Registers" present on some flash chips.
A subset of them are pre-programmed at the factory with a
unique set of values. The rest is user-programmable.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Prevent deadlock when checking erased block for
space allocation during wbuf recovery.
Signed-off-by: Estelle Hammache <estelle.hammache@st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* Removed table entry for AM29BDS643D, since device ID clashes with AM29DL640G
and both chips support CFI.
Signed-off-by: Jonas Holmberg <jonas.holmberg@axis.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Try larger numbers of chips before smaller
numbers of chips across the bus width.
This means we'll avoid misdetecting a 2 x16 array as 1 x32 if the
high 16-bits happen to read as zeros in the QRY area.
Signed-off-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
avoid segfault when nextblock was refiled because of a write failure
- avoid filing blocks on the clean list when they have wasted
space
Signed-off-by: Estelle Hammache <estelle.hammache@st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- block refiling when writing directly to flash a buffer
which is bigger than wbuf
- retry cases for flushing wbuf
Signed-off-by: Estelle Hammache <estelle.hammache@st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Correction of retry case to avoid silent failure of rmdir
when jffs2_wbuf_recover GCs the previous entry (+ corresponding
dnode case).
Signed-off-by: Estelle Hammache <estelle.hammache@st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added routine to perform extra error status checks on erase and write
failures to determine if errors are correctable.
Added option to prevent JFFS2 from using virtual erase blocks.
Performed minor cleanup on whitespace and comments.
Signed-off-by: David A. Marlin <dmarlin@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add optional hardware specific callback routine to perform extra error
status checks on erase and write failures for devices with hardware ECC.
Signed-off-by: David A. Marlin <dmarlin@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Driver for generic RAM blocks which are exported by an platform_device
from the device driver system.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Avoid "Eep. No valid nodes for ino #1" message for just-created filesystem.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Ensure the whole device is added if there are no partitions found on the
device, so that at least the flash can be read/written.
Replace some of the constants with their SZ_xxx counterparts
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
