And fix up the code to always allow MSI on 5714 A2.
Call tg3_find_peer() earlier because we need that information before
we can determine whether we can set TG3_FLAG_SUPPORT_MSI or not.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the use of the TG3_FLAG_5701_REG_WRITE_BUG flag.
It's logic is only used to set a function pointer and thus the
logic can be collapsed and the flag removed.
[ Comment tidy by Christoph Hellwig. -DaveM ]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
The reset was added a while back so that ASF could re-init whatever
MAC address it wanted to use after the MAC address was changed.
Instead of resetting, we can just keep MAC address 1 unchanged during
MAC address changes if MAC address 1 is different from MAC address 0.
This fixes 2 problems:
1. Bonding calls set_mac_address in contexts that cannot sleep.
It no longer sleeps with the chip reset removed.
2. When ASF shares the same MAC address as the NIC, it needs to
always do that even when the MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TG3_FLAG_SERDES_WOL_CAP to TG3_FLAG_WOL_CAP to make it easier
to manage WoL. This flag is now used consistently during ethtool WoL
setup and power setting changes.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO settings may change during reset and so the stored values in
tp->grc_local_ctrl should be cleared first.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the NVRAM sizing procedure so that the driver can
take advantage of devices with 1:1 NVRAM strapping configurations. This
is useful in cases where the traditional NVRAM sizing method fails. In
the event that the flash size cannot be determined, the largest known
NVRAM size is used. The patch also removes support for 5755 NVRAM
devices that are not supported by Broadcom and adds explicit sizing for
this device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove the check for skb->len greater than MTU when doing TSO.
When the destination has a smaller MSS than the source, a TSO packet
may be smaller than the MTU and we still need to process it as a TSO
packet.
2. On 5705A3 devices with TSO enabled, the DMA engine can hang due to a
hardware bug. This patch avoids the hanging condition by reducing the
DMA burst size.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MAINTAINERS entry for mac80211.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export various mac80211 internal variables through debugfs.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic IEEE 802.11 definitions.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People treating the *_pid fields in netlink as a process ID has caused
endless confusion over the years. The fact that our own netlink.h
does this only adds to the confusion.
So here is a patch to change the comments to refer to it as the port
ID which hopefully will make it clear what the purpose of the fields
really is.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Heiko Carstens <heiko.carstens@de.ibm.com>
CC [M] net/iucv/af_iucv.o
net/iucv/af_iucv.c: In function `iucv_fragment_skb':
net/iucv/af_iucv.c:984: error: structure has no member named `h'
net/iucv/af_iucv.c:985: error: structure has no member named `nh'
net/iucv/af_iucv.c:988: error: incompatible type for argument 1 of
`skb_queue_tail'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (46 commits)
mmc-omap: Clean up omap set_ios and make MMC_POWER_ON work
mmc-omap: Fix omap to use MMC_POWER_ON
mmc-omap: add missing '\n'
mmc: make tifm_sd_set_dma_data() static
mmc: remove old card states
mmc: support unsafe resume of cards
mmc: separate out reading EXT_CSD
mmc: break apart switch function
MMC: Fix handling of low-voltage cards
MMC: Consolidate voltage definitions
mmc: add bus handler
wbsd: check for data opcode earlier
mmc: Separate out protocol ops
mmc: Move core functions to subdir
mmc: deprecate mmc bus topology
mmc: remove card upon suspend
mmc: allow suspended block driver to be removed
mmc: Flush pending detects on host removal
mmc: Move host and card drivers to subdirs
mmc: Move queue functions to mmc_block
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Force use of GFP_NOFS in ocfs2_write()
ocfs2: fix sparse warnings in fs/ocfs2/cluster
ocfs2: fix sparse warnings in fs/ocfs2/dlm
ocfs2: fix sparse warnings in fs/ocfs2
[PATCH] Copy i_flags to ocfs2 inode flags on write
[PATCH] ocfs2: use __set_current_state()
ocfs2: Wrap access of directory allocations with ip_alloc_sem.
[PATCH] fs/ocfs2/: make 3 functions static
ocfs2: Implement compat_ioctl()
We used to BUG_ON() for a badly mapped IO port, which is certainly
correct, but actually made it harder to debug the case where the ATA
drivers had incorrectly mapped a nonconnected ATA port.
So make badly mapped ports trigger a WARN_ON(), and throw the IO away
instead (and return all ones for reads). For things like broken driver
initialization - which is the most likely cause anyway - that should
mean that the machine comes up and is usable (at least that was the case
for the ATA breakage that triggered this patch).
It tends to be a whole lot easier to do a "dmesg" on a working machine
than to try to capture logs off a dead one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (28 commits)
NFS: Fix a compile glitch on 64-bit systems
NFS: Clean up nfs_create_request comments
spkm3: initialize hash
spkm3: remove bad kfree, unnecessary export
spkm3: fix spkm3's use of hmac
NFS4: invalidate cached acl on setacl
NFS: Fix directory caching problem - with test case and patch.
NFS: Set meaningful value for fattr->time_start in readdirplus results.
NFS: Added support to turn off the NFSv3 READDIRPLUS RPC.
SUNRPC: RPC client should retry with different versions of rpcbind
SUNRPC: remove old portmapper
NFS: switch NFSROOT to use new rpcbind client
SUNRPC: switch the RPC server to use the new rpcbind registration API
SUNRPC: switch socket-based RPC transports to use rpcbind
SUNRPC: introduce rpcbind: replacement for in-kernel portmapper
SUNRPC: Eliminate side effects from rpc_malloc
SUNRPC: RPC buffer size estimates are too large
NLM: Shrink the maximum request size of NLM4 requests
NFS: Use pgoff_t in structures and functions that pass page cache offsets
NFS: Clean up nfs_sync_mapping_wait()
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (49 commits)
[SCTP]: Set assoc_id correctly during INIT collision.
[SCTP]: Re-order SCTP initializations to avoid race with sctp_rcv()
[SCTP]: Fix the SO_REUSEADDR handling to be similar to TCP.
[SCTP]: Verify all destination ports in sctp_connectx.
[XFRM] SPD info TLV aggregation
[XFRM] SAD info TLV aggregationx
[AF_RXRPC]: Sort out MTU handling.
[AF_IUCV/IUCV] : Add missing section annotations
[AF_IUCV]: Implementation of a skb backlog queue
[NETLINK]: Remove bogus BUG_ON
[IPV6]: Some cleanups in include/net/ipv6.h
[TCP]: zero out rx_opt in tcp_disconnect()
[BNX2]: Fix TSO problem with small MSS.
[NET]: Rework dev_base via list_head (v3)
[TCP] Highspeed: Limited slow-start is nowadays in tcp_slow_start
[BNX2]: Update version and reldate.
[BNX2]: Print bus information for PCIE devices.
[BNX2]: Add 1-shot MSI handler for 5709.
[BNX2]: Restructure PHY event handling.
[BNX2]: Add indirect spinlock.
...
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (65 commits)
Input: gpio_keys - add support for switches (EV_SW)
Input: cobalt_btns - convert to use polldev library
Input: add skeleton for simple polled devices
Input: update some documentation
Input: wistron - fix typo in keymap for Acer TM610
Input: add input_set_capability() helper
Input: i8042 - add Fujitsu touchscreen/touchpad PNP IDs
Input: i8042 - add Panasonic CF-29 to nomux list
Input: lifebook - split into 2 devices
Input: lifebook - add signature of Panasonic CF-29
Input: lifebook - activate 6-byte protocol on select models
Input: lifebook - work properly on Panasonic CF-18
Input: cobalt buttons - separate device and driver registration
Input: ati_remote - make button repeat sensitivity configurable
Input: pxa27x - do not use deprecated SA_INTERRUPT flag
Input: ucb1400 - make delays configurable
Input: misc devices - switch to using input_dev->dev.parent
Input: joysticks - switch to using input_dev->dev.parent
Input: touchscreens - switch to using input_dev->dev.parent
Input: mice - switch to using input_dev->dev.parent
...
Fixed up conflicts with core device model removal of "struct subsystem" manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
remove "struct subsystem" as it is no longer needed
sysfs: printk format warning
DOC: Fix wrong identifier name in Documentation/driver-model/devres.txt
platform: reorder platform_device_del
Driver core: fix show_uevent from taking up way too much stack
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits)
PCI: Free resource files in error path of pci_create_sysfs_dev_files()
pci-quirks: disable MSI on RS400-200 and RS480
PCI hotplug: Use menuconfig objects
PCI: ZT5550 CPCI Hotplug driver fix
PCI: rpaphp: Remove semaphores
PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry
PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically
PCI: rpaphp: Document is_php_dn()
PCI: rpaphp: Document find_php_slot()
PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot()
PCI: rpaphp: refactor tail call to rpaphp_register_slot()
PCI: rpaphp: remove rpaphp_set_attention_status()
PCI: rpaphp: remove print_slot_pci_funcs()
PCI: rpaphp: Remove setup_pci_slot()
PCI: rpaphp: remove a call that does nothing but a pointer lookup
PCI: rpaphp: Remove another wrappered function
PCI: rpaphp: Remve another call that is a wrapper
PCI: rpaphp: remove a function that does nothing but wrap debug printks
PCI: rpaphp: Remove un-needed goto
PCI: rpaphp: Fix a memleak; slot->location string was never freed
...
ps3av:
- Move the definition of struct ps3av to ps3av.c, as it's locally used only.
- Kill ps3av.sem, use the existing ps3av.mutex instead.
- Make the 512-byte buffer in ps3av_do_pkt() static to reduce stack usage.
Its use is protected by a semaphore anyway.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3av: Replace the kernel_thread and the ping pong semaphores by a singlethread
workqueue and a completion.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Replace the kernel_thread and the semaphore by a proper kthread, which
is simply woken up when the screen must be updated
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert kmap_atomic() in the non-highmem case from a macro to a static
inline function, for better type-checking and the ability to pass void
pointers instead of struct page pointers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent conversion from `memcpy' to `skb_copy_from_linear_data' removed a
few casts, which were needed to silence compiler warnings. Re-add them.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kill resource_size_t warnings by casting resource_size_t to unsigned long when
formatting Zorro bus resources, as they are always 32-bit.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Install the built-in macsonic interrupt handler on both IRQs when using
via_alt_mapping. Otherwise the rare interrupt that still comes from the
nubus slot will wedge the nubus.
$ cat /proc/interrupts
auto 2: 89176 via2
auto 3: 744367 sonic
auto 4: 0 scc
auto 6: 318363 via1
auto 7: 0 NMI
mac 9: 119413 framebuffer vbl
mac 10: 1971 ADB
mac 14: 198517 timer
mac 17: 89104 nubus
mac 19: 72 Mac ESP SCSI
mac 56: 629 sonic
mac 62: 1142593 ide0
Version 1 of this patch had a bug where a nubus sonic card would register
two interrupt handlers. Only a built-in sonic needs both.
Versions 2 and 3 needed some cleanups, as Raylynn Knight and Christoph
Hellwig pointed out (thanks).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a potential problem in the timeout handling: don't free the DMA buffers
before resetting the chip.
Also a trivial cleanup. Bring macsonic and jazzsonic into sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a race condition in the transmit code, where the dma interrupt could update
the free tx buffer count concurrently and wedge the tx queue.
Fix the misuse of the rx frame status and rx frame length registers: no more
"fifo overrun" errors caused by the OFLOW bit being tested in the frame length
register (instead of the status register), and no more missed packets due to
incorrect length taken from status register (instead of the frame length
register).
Fix a panic (skb_over_panic BUG) caused by allocating and then copying an
incoming packet while the packet length register was changing.
Cut-and-paste the reset code from the powermac mace driver (mace.c), so the NIC
functions when MacOS does not initialise it (important for anyone wanting to
use the Emile boot loader).
Cut-and-paste the error counting and timeout recovery code from mace.c.
Fix over allocation of rx buffer memory (it's page order, not page count).
Converted to driver model.
Converted to DMA API.
Since I've run out of ways to make it fail, and since it performs well now,
promote the driver from EXPERIMENTAL status. Tested on both quadra 840av and
660av.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the flakiness in the CUDA ADB driver on m68k macs (keypresses getting
wedged down or ADB just going AWOL altogether).
The only IRQ used by this driver is the VIA shift register IRQ. The PowerMac
conditional code disables the other VIA IRQ sources, so don't mess with the
other IRQ flags in the common code -- m68k macs need them.
When polling, don't disable local interrupts when we only need to disable the
CUDA interrupt.
Unless polling, don't clear the shift register IRQ flag. On m68k macs this
creates a race that often breaks CUDA ADB.
Tested on Quadra 840av and LC630 (both m68k); also Beige G3 (powerpc).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a crash caused by requests placed in the queue with the completed flag
already set. This lead to some ADB_SYNC requests returning early and their
request structs being popped off the stack while still queued. Stack corruption
ensued or an invalid request callback pointer was invoked or both. Eliminate
macii_retransmit() and its buggy implementation of macii_write(). Have
macii_queue_poll() fully initialise the request queues.
Fix a bug in macii_queue_poll() where the last_req pointer was not being set.
This caused some requests to leave the queue before being completed (and would
also corrupt the stack under certain conditions).
Fix a race in macii_start that could set the state machine to "reading" while
current_req was null.
No longer send poll commands with the ADBREQ_REPLY flag -- doing that caused
the replies to be stored in the request buffer where they were forgotten
about.
Don't autopoll by continuously sending new Talk commands. Get the controller to
do that for us. This reduces the ADB interrupt rate on an idle bus to about 5
per second. Only autopoll the devices that were probed.
Explicitly clear the interrupt flag when polling.
Use disable_irq rather than local_irq_save when polling.
Remove excess local_irq_save/restore pairs.
Improve bus timeout and service request detection.
Remove unused code (last_reply, adb_dir etc) and unneeded code (prefix_len,
first_byte etc).
Change TIP and TACK to their correct names on this ADB controller (ST_EVEN and
ST_ODD).
Add some commentry.
Add a generous quantity of sanity checks (BUG_ONs).
Let m68k macs use the adb_sync boot param too.
Tested on Mac II, Mac IIci, Quadra 650, Quadra 700 etc.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are no slow IRQs on Macs since Roman Zippel's IRQ reorganisation that
went into 2.6.16 and removed mac_irq_list[] and the do_mac_irq_list()
dispatcher. (They were implemented in do_mac_irq_list() by lowering the IPL.)
Hence there's no more use for mutual exclusion in the Mac interrupt
dispatchers. Remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some Macs lack a slot interrupt enable register. So the existing code makes
disabled and unregistered slot IRQ lines outputs set high. This seems to work
on quadras, but does not work on genuine VIAs (perhaps the card still succeeds
in pulling the line low, or perhaps because this increases the settle time on
the port A input, meaning that the CA1 IRQ could fire before the slot line
reads active).
Because of this, the nubus_active flags were used to mask IRQs, which is
actually worse than the problem it tries to solve. Any interrupt masked by
nubus_active will remain asserted and prevent further transitions on CA1. And
so the nubus gets wedged regardless of hardware (emulated VIA ASIC, real VIA
chip or RBV).
The best solution to this hardware limitation of genuine VIAs is to disable the
umbrella SLOTS IRQ when disabling a slot on those machines. Unfortunately, this
means all slot IRQs get disabled when any slot IRQ is disabled. But it is only
a problem when there's more than 1 device using nubus interrupts.
Another potential problem for genuine VIAs is an unregistered nubus IRQ.
Eventually it will be possible to enable the CA1 interrupt by installing its
handler only _after_ all nubus drivers have loaded but _before_ the kernel
needs them, at which time this last problem can be fixed. For now it can be
worked around:
- disable MacOS extensions
- don't boot MacOS (use the Emile bootloader instead)
- get the bootloaders to disable ROM drivers (Penguin does this for video
cards already, don't know about Emile)
- physically remove unsupported cards
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure that there are no slot IRQs asserted before leaving the nubus
handler. If there are and we don't then the nubus gets wedged because this
prevents a CA1 transition, which means no more nubus IRQs.
Make the interrupt dispatch loops terminate sooner.
Explicitly initialise the VIA latches to make the code more easily understood.
Also some cleanups.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reverse the last of a monumental brown-paper-bag commit that went into the 2.3
kernel.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the support for C/NET nubus ethernet cards etc. Sync up the DP8390 driver
with the latest code in the mac68k repo.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sync the nubus defines with the latest code in the mac68k repo. Some of these
are needed for DP8390 driver update in the next patch.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some more machines that support A/UX interrupt priorities. There are
probably others as well, but I've only tested these ones so far.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The asm-m68k/adb.h header is unused. Some definitions are wrong and the rest
are duplicated in linux/adb.h. Remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
